net: dwmac_meson8b: do not set TX delay in TXID & RXID

When the PHY interface is set as TXID & RXID, the delays should be taken from DT,
but first they should not be hardcoded since the PHY driver will set them.

Fixes: 798424e857 ("net: designware: add Amlogic Meson8b & later glue driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This commit is contained in:
Neil Armstrong 2021-05-05 09:52:08 +02:00
parent 60e531fabf
commit 81d0edafd9

View file

@ -59,8 +59,6 @@ static int dwmac_setup_axg(struct udevice *dev, struct eth_pdata *edata)
switch (edata->phy_interface) {
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RGMII_RXID:
case PHY_INTERFACE_MODE_RGMII_TXID:
/* Set RGMII mode */
setbits_le32(plat->regs + ETH_REG_0, AXG_ETH_REG_0_PHY_INTF_RGMII |
AXG_ETH_REG_0_TX_PHASE(1) |
@ -69,6 +67,15 @@ static int dwmac_setup_axg(struct udevice *dev, struct eth_pdata *edata)
AXG_ETH_REG_0_CLK_EN);
break;
case PHY_INTERFACE_MODE_RGMII_RXID:
case PHY_INTERFACE_MODE_RGMII_TXID:
/* TOFIX: handle amlogic,tx-delay-ns & rx-internal-delay-ps from DT */
setbits_le32(plat->regs + ETH_REG_0, AXG_ETH_REG_0_PHY_INTF_RGMII |
AXG_ETH_REG_0_TX_RATIO(4) |
AXG_ETH_REG_0_PHY_CLK_EN |
AXG_ETH_REG_0_CLK_EN);
break;
case PHY_INTERFACE_MODE_RMII:
/* Set RMII mode */
out_le32(plat->regs + ETH_REG_0, AXG_ETH_REG_0_PHY_INTF_RMII |
@ -90,8 +97,6 @@ static int dwmac_setup_gx(struct udevice *dev, struct eth_pdata *edata)
switch (edata->phy_interface) {
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RGMII_RXID:
case PHY_INTERFACE_MODE_RGMII_TXID:
/* Set RGMII mode */
setbits_le32(plat->regs + ETH_REG_0, GX_ETH_REG_0_PHY_INTF |
GX_ETH_REG_0_TX_PHASE(1) |
@ -101,6 +106,16 @@ static int dwmac_setup_gx(struct udevice *dev, struct eth_pdata *edata)
break;
case PHY_INTERFACE_MODE_RGMII_RXID:
case PHY_INTERFACE_MODE_RGMII_TXID:
/* TOFIX: handle amlogic,tx-delay-ns & rx-internal-delay-ps from DT */
setbits_le32(plat->regs + ETH_REG_0, GX_ETH_REG_0_PHY_INTF |
GX_ETH_REG_0_TX_RATIO(4) |
GX_ETH_REG_0_PHY_CLK_EN |
GX_ETH_REG_0_CLK_EN);
break;
case PHY_INTERFACE_MODE_RMII:
/* Set RMII mode */
out_le32(plat->regs + ETH_REG_0, GX_ETH_REG_0_INVERT_RMII_CLK |