Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
SMMU is disabled by default and not all masters can be enabled at the same
time because of limited number of entries. That's why comment all iommu
properties but keep them for reference in DT. In XEN case they should be
added back and Xen should have SMMU enabled by default.
Also add IDs for DP and DPDMA.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e868c27c52ded5d8ef25f75ba394b1ab3b31b80a.1698825657.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/28b3cdd7e91b2b4c3c36d0bf65aa5bac042f248c.1698329087.git.michal.simek@amd.com
gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state
is enabled for MIO38, causing inappropriate PHY register reads.
Disabled Tri-state for MIO38 to make HW reset work.
Tri-state disable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7a3 00000540
Tri-state enable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7e3 00000540
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20231020050622.972750-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Board specific late init allows vendors to set up different device
or board specific env variables (like serial number, platform name).
In case this information is missing, u-boot will lack info regards
serial or platform.
To avoid this prior nvidia_board_late_init internal generic function
is called which fills required data. In this case platform name is
obtained from get_chip and serialno is filled with SoC id.
Though SoC id is not dedicated to be devices serial but it fits well
in case of restriction of data about device and since SoC is basically
a main chip of the device.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Transformers
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Re-crypt support was extended to devices without burnt SBK. In case
SBK is not set, place from where it is read is filled with zeroes.
This patch adds support for ebtupdate function to detect nosbk device
and avoid crypto operations for it.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra 4, same as Tegra 3, requires configuration of CPU and CORE
voltages in the SPL stage to boot properly. Expose function to be
able perform this configuration in the SPL section of the device
board.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS TF701T
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TF201 unlike other transformers uses non-fused xcvr value for
its dock USB port. With out it dock USB and SD reader will not
work.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TF600T has significant differences (Tegra DSI and DSI panel,
own power supply system) which makes use of common transformer
device tree complicated.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
P1801-T has significant differences (hdmi panel and backlight,
own power supply system) which makes use of common transformer
device tree complicated.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Default-tap and default-trim values are used for eMMC setup
mostly on T114+ devices. As for now, those values are hardcoded
for T210 and ignored for all other Tegra generations. Fix this
by passing tap and trim values from dts.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra MMC driver has hardcoded tap and trim values as for now.
Set default-tap and default-trim values in sdhci nodes to avoid
regressions in case Tegra MMC driver is upated to use dts values.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
For most source files we can just drop <common.h>. We need to add an
include for <asm/u-boot.h> in a couple of places. Also sort the include
list in memmap-gen3.c while we're here.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
If <common.h> won't be included before <asm/armv8/mmu.h>, we need to
ensure that we have the required type definitions.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
Disarm the error message forcing u-boot/spl image to be located at
sector 0 on eMMC data-partition and microSD.
Offset 0 makes sense on eMMC boot partitions only, data partition must
use 4096 to avoid conflicting with MBR.
Valid offsets when booting from microSD, reported by boot-rom v1.73:
BootROM: Bad header at offset 00000200
BootROM: Bad header at offset 00004400
BootROM: Bad header at offset 00200000
BootROM: Bad header at offset 00400000
BootROM: Bad header at offset 00600000
BootROM: Bad header at offset 00800000
BootROM: Bad header at offset 00A00000
BootROM: Bad header at offset 00C00000
BootROM: Bad header at offset 00E00000
BootROM: Bad header at offset 01000000
BootROM: Bad header at offset 01200000
BootROM: Bad header at offset 01400000
BootROM: Bad header at offset 01600000
BootROM: Bad header at offset 01800000
BootROM: Bad header at offset 01A00000
BootROM: Bad header at offset 01C00000
BootROM: Bad header at offset 01E00000
BootROM: Bad header at offset 02000000
BootROM: Bad header at offset 02200000
BootROM: Bad header at offset 02400000
BootROM: Bad header at offset 02600000
BootROM: Bad header at offset 02800000
BootROM: Bad header at offset 02A00000
BootROM: Bad header at offset 02C00000
BootROM: Bad header at offset 02E00000
Valid offsets when booting from eMMC:
BootROM: Bad header at offset 00000000
BootROM: Bad header at offset 00200000
Switching BootPartitions.
BootROM: Bad header at offset 00000000
BootROM: Bad header at offset 00200000
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.
Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.
Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3588 and rock-5b contain usb3 nodes that have
deviated too much from current state of submitted mainline linux usb3
patches, see [1].
Sync usb3 related nodes from latest patches and collaboras rk3588 tree
so that dwc3-generic driver can be updated to include support for the
rockchip,rk3588-dwc3 compatible in the future, use rockchip,rk3568-dwc3
compatible until final node is merged in linux maintainer tree.
[1] https://lore.kernel.org/lkml/20231009172129.43568-1-sebastian.reichel@collabora.com/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmU2fxwcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyKr+B/42+WkPiAiwt79R6Kh5
UKo404oN1na28D3V12EvikiCH2QWubi38EV7VfcB3jqEpxj4j+rY0cSLZv+u7d4/
bfQN3FPrcTwYnXYLbYkUKC+MAVzGLiVzFBBhIt5cPrT4iVXctwYY6LJ58aX8uRo6
KU6CwXYc3cnmIUqpXE4EYbbQU4TAp55SV2n8QLFFI9DHcy2kELfdrZduFn+Hm9Ij
9sQHH5JxbrGHv5XpcjJkARW3M4K3K4TPzweFGN61VMJwWqzD3L4YPshwIGDfhRui
LECKCdr/rWkavumXCfw2pD3RYFTqnqnUzaEN/3ueL9FCJ2uFH1EyaoSuXFEn3+Ul
m1LE
=CMMd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2024.01 cycle
This feature set a new board named Conclusive KSTR sama5d27 with some
small prerequisites patches.
This is mostly about support for the Allwinner R528/T113s SoC, which is
reportedly the same die as the Allwinner D1, but with the two
Arm Cortex-A7 cores activated instead of the RISC-V one.
Using sunxi code outside of arch/arm proved to be difficult, so apart
from enabling this Arm SoC, the patches also prepare for more refactoring
to get the D1 nicely supported some day:
- We get rid of some Kconfig (hard-)coded GPIO pins, responsible for
enabling regulators.
- The GPIO code is moved out of arch/arm, into drivers/gpio.
- Some definitions are moved out of header files under asm/arch.
- Some T113s/D1 specific definitions are guarded by a generic Kconfig
symbol (CONFIG_SUNXI_GEN_NCAT2).
- The DRAM controller initialisation code is located under drivers/ram.
- The base SoC .dtsi files are shared (under arch/riscv, as in Linux).
Of course there are also the usual new SoC specific patches, like clock
and pinmux descriptions, alongside a rework of the pinctrl code, since
Allwinner changed the GPIO register layout, for the first time since
sunxi's inception.
On top of this the PSCI code sees some update, to provide SMP services
for R528/T113s boards. Many thanks to Sam for providing this code and
staying strong through the review cycles.
The final patch enables support for one popular board, I hope to see
more DTs and defconfigs contributed in the future!
Many thanks to all the various contributors, testers and reviewers,
that series was a real team effort!
Introduce support for Conclusive KSTR-SAMA5D27 Single Board Computer.
Co-developed-by: Jakub Klama <jakub@conclusive.pl>
Signed-off-by: Jakub Klama <jakub@conclusive.pl>
Co-developed-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Sync the rk3328-rock64 dts from v6.6-rc5.
See Linux kernel commit for details:
03633c4ef1fb ("arm64: dts: rockchip: fix USB regulator on ROCK64")
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.
There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR
Specifications:
CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
+ 4x Cortex-A55 (up to 1.8GHz)
GPU: Mali-G610 MP4
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
eMMC: 0GB/32GB/64GB/256GB HS400
MicroSD Slot: MicroSD SDR104
PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
supports M.2 WiFi and Bluetooth
4G Module: MiniPCIe x1, MicroSIM Card Slot x1
Audio Out: 3.5mm jack for stereo headphone output
Audio In: 2.0mm PH-2A connector for analog microphone input
Video Input: standard HDMI input port, up to 4Kp60
2x 4-lane MIPI-CSI, compatible with MIPI V1.2
Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
HDMI2.0, and HDMI1.4
2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
USB-A: USB 3.0, Type A
USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
8x PWMs, 2x I2Ss, 28x GPIOs
Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
Onboard IR receiver: 38KHz carrier frequency
RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
RTC IC HYM8563TS
5V Fan connector
Working Temperature: 0C to 70C
Power: 5.5*2.1mm DC Jack, 12VDC input
Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)
Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable mini PCIe slot, pcie3x1 node, now that the PCIe PHY driver
support bifurcation.
A pinctrl is assigned for reset-gpios or the device may freeze running
pci enum and nothing is connected to the mini PCIe slot.
Also drop the AHCI_PCI Kconfig option as this option is not required for
a functional M.2 SATA drive slot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The MangoPi MQ-R board uses an Allwinner T113s Soc (with 128MB of
embedded DRAM), support for which was just added to the code.
Since the devicetree was already synced from the latest Linux kernel
tree, all we need is a _defconfig file to add support for the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
