Commit graph

716 commits

Author SHA1 Message Date
Luca Ceresoli
6da4f67ad0 arm/arm64: zynq/zynqmp: pass the PS init file as a kconfig variable
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:

 1. if a board-specific file exists in
    board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
    then use it
 2. otherwise use board/xilinx/zynq/ps?_init_gpl.c

In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).

This generates a few problems:

 * if the source tree is shared among different out-of-tree builds,
   they will pollute (and potentially corrupt) each other
 * the source tree cannot be read-only
 * any buildsystem must add a command to copy the PS init file binary
 * overwriting or deleting files in the source tree is ugly as hell

Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.

Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.

Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.

Build-tested with all combinations of:
 - platform: zynq or zynqmp
 - PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
   non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
 - building in-tree, in subdir, in other directory

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:53 +02:00
Ley Foon Tan
a684729a15 arm: socfpga: stratix10: Enable Stratix10 SoC build
Add build support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>

Conflicts:

	arch/arm/Kconfig
	arch/arm/mach-socfpga/Kconfig
2018-07-12 09:22:12 +02:00
Thomas Fitzsimmons
894c3ad27f board: arm: Add support for Broadcom BCM7445
Add support for loading U-Boot on the Broadcom 7445 SoC.  This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.

Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-07-10 16:55:57 -04:00
Manivannan Sadhasivam
eba6589f7e board: Add uCRobotics Bubblegum-96 board support
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.

Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons

U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:23 -04:00
Manivannan Sadhasivam
97775d26c2 arm: Add support for Actions Semi OWL SoC family
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:15 -04:00
Nishanth Menon
c2ca3fdfb9 ARM: Introduce ability to enable invalidate of BTB with ICIALLU on Cortex-A15 for CVE-2017-5715
As recommended by Arm in [1], ACTLR[0] (Enable invalidates of BTB)
needs to be set[2] for BTB to be invalidated on ICIALLU. This needs to
be done unconditionally for Cortex-A15 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.

NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
   provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the
   right locations.
c) This workaround applies to only the boot processor. It is important
   to apply workaround as necessary (context-save-restore) around low
   power context loss OR additional processors as necessary in either
   firmware support OR elsewhere in OS.

[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438c/BABGHIBG.html

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-29 11:30:39 -04:00
Nishanth Menon
7b37a9c732 ARM: Introduce ability to enable ACR::IBE on Cortex-A8 for CVE-2017-5715
As recommended by Arm in [1], IBE[2] has to be enabled unconditionally
for BPIALL to be functional on Cortex-A8 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.

NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
   provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the right
   locations.
c) This workaround applies to only the boot processor. It is important
   to apply workaround as necessary (context-save-restore) around low
   power context loss OR additional processors as necessary in either
   firmware support OR elsewhere in OS.

[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0344k/Bgbffjhh.html

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-29 11:30:39 -04:00
Vinitha V Pillai
2d91b53331 LS1012AFRWY: Add Secure Boot support
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11 12:34:45 -07:00
Bhaskar Upadhaya
9629ccdde7 board: ls1012a: FRWY-LS1012A board support
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.

Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11 12:34:45 -07:00
Alex Kiernan
312a10f16b fastboot: Move fastboot to drivers/fastboot
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.

Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-30 11:59:21 +02:00
Patrick Delaunay
c3600e1f92 stm32mp1: add FUSE command support
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26 18:19:18 -04:00
Tom Rini
ea37f0b312 arm: armv7m: Clean up some thumb / compiler flag options
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
  sub-config.mk file.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-23 13:03:42 -04:00
Tom Rini
f58e94602e at91: Minor tweaks to SPL logic for space savings on smartweb
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
  SPL and instead let full U-Boot handle it.  Instead of an empty
  function just do not call a function.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-22 22:08:57 -04:00
Tom Rini
904e546970 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-05-20 09:44:05 -04:00
Marek Vasut
73172753f4 ARM: socfpga: Convert to DM serial
Pull the serial port configuration from DT and use DM serial instead
of having the serial configuration in two places, DT and board config.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Marek Vasut
48befc009f ARM: socfpga: Clean up Kconfig entries
Shuffle the default Kconfig entries around so it is not such a mess.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Magnus Lilja
3159ec64f5 mx31pdk: Convert CONFIG_MX31 flag to use Kconfig.
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-17 12:02:24 +02:00
Michal Simek
1d6c54ecb3 arm: zynqmp: Add ZynqMP minimal R5 support
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.

This configuration with uart1 was tested on zcu100-revC.

U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)

Model: Xilinx ZynqMP R5
DRAM:  512 MiB
WARNING: Caches not enabled
MMC:
In:    serial@ff010000
Out:   serial@ff010000
Err:   serial@ff010000
Net:   Net Initialization Skipped
No ethernet found.
ZynqMP r5>

There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split

2. Load via jtag when directly to R5

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:38:23 +02:00
Michal Simek
4aba5fb857 arm: zynq: Rework FPGA initialization
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.

Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Lokesh Vutla
f2ef204312 arm: v7R: Add support for MPU
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.

[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0460d/I1002400.html

Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-07 15:53:29 -04:00
Michal Simek
4bbd6b1d94 arm: v7R: Add initial support
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.

Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-05-07 15:53:28 -04:00
Lokesh Vutla
f4bcd767bd arm: v7: Kconfig: Introduce SYS_ARM_CACHE_CP15
Certain ARM architectures like ARMv7-A, ARMv7-R has support for
enabling caches using CP15 registers. To have a common support
for all these architectures, introduce a Kconfig symbol
SYS_ARM_CACHE_CP15 that selects cache-cp15.c

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-05-07 15:53:28 -04:00
Lokesh Vutla
7240b80ee0 arm: v7: Kconfig: Add entry for MMU
Add a Kconfig entry for MMU and imply for all platforms using
cache-cp15.c containing MMU setup. Using imply instead of select so that
MMU can be disabled by defconfigs when not needed.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-05-07 15:53:28 -04:00
Lokesh Vutla
acf1500138 arm: v7: Kconfig: Rename CPU_V7 as CPU_V7A
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.

As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.

Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-05-07 15:53:24 -04:00
Tom Rini
b25f8e2112 Merge git://git.denx.de/u-boot-imx 2018-04-30 07:14:05 -04:00
Andre Przywara
7842b6a91e arm: move SYS_ARCH_TIMER to KConfig
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-04-28 18:30:43 -04:00
Masahiro Yamada
7325f6cfdc distro: use imply to enable DISTRO_DEFAULTS as SoC default
The default of DISTRO_DEFAULTS is messy.  Using the 'imply' keyword
is equivalent and cleaner.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-28 10:42:35 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Mans Rullgard
07a8f79ee8 ARM: mxs: support full SPL framework
This allows using the full SPL framework on mxs devices.  In this
mode, the u-boot.sb image loaded by the boot ROM contains only the
SPL which then loads U-Boot proper or a kernel in falcon mode.

Signed-off-by: Mans Rullgard <mans@mansr.com>
2018-04-27 09:32:54 +02:00
Kever Yang
c3c0331db1 rockchip: enable SYS_NS16550 for all SoCs by default
All rockchip SoCs can use ns16550 driver, enable it for all
and set SYS_NS16550_MEM32 for all SoCs.

Version-changes: 2
- use imply instead of select

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-25 22:20:07 +02:00
Tom Rini
ebca902aeb Merge git://git.denx.de/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 08:43:50 -04:00
Tom Rini
448fc44fb8 mx31ads: Delete
This platform has been marked as orphaned since September 2013, remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 11:54:02 +02:00
Tom Rini
bcca8aa9ee imx31_phycore: Delete
This platform has been marked as orphaned since September 2013, remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 11:52:39 +02:00
Patrick Delaunay
86634a93b4 stm32mp: handle SYSRESET
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06 20:45:44 -04:00
Patrick Delaunay
08772f6e79 stm32mp1: get boot mode from BootRom
SPL copy BootRom boot mode information
in TAMP register 21.

This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06 20:45:28 -04:00
Siva Durga Prasad Paladugu
c436bf92f6 arm64: zynqmp: Add support for verifying secure images
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:36:15 +01:00
Michal Simek
e6cc3b25d7 arm: zynq: Wire watchdog internals
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:34:43 +01:00
Patrick Delaunay
2514c2d0e6 arm: stm32: add new architecture for STM32MP family
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:21 -04:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Andrew F. Davis
5fbed8f2c6 ARM: Kconfig: Move TI_SECURE_DEVICE to a common area
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.

Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.

Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.

Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-02-23 10:21:41 -05:00
Simon Goldschmidt
fef4a545b6 arm: socfpga: use imply instead of select where applicable
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.

These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
  partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
  should still work without it.

Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
2018-02-15 13:45:16 +01:00
Lukasz Majewski
21a9f435f3 Convert socfpga: select CONFIG_HW_WATCHDOG support for ARCH_SOCFPGA
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
2018-02-15 13:45:16 +01:00
Simon Goldschmidt
7d531e8a4f arm: update Kconfig help for ENABLE_ARM_SOC_BOOT0_HOOK
When this config is enabled, <asm/arch/boot0.h> is included,
but the Kconfig help says this should be a define
(ARM_SOC_BOOT0_HOOK).

The code for this in arch/arm/lib/vectors.s was changed on
01/02/2017 with commit ce62e57fc5 ("ARM: boot0 hook: remove macro,
include whole header file").

Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
2018-02-13 23:24:22 -05:00
Stefan Agner
ac4605ae64 spl: use ARCH_MX23/28 to specify SPL_LDSCRIPT
Simplify SPL_LDSCRIPT config by using the new arch Kconfig
configurations ARCH_MX23 and ARCH_MX28.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-02-08 10:17:17 -05:00
Stefan Agner
25c5b4e1bf arm: imx: mx28: Move MX28 selection to Kconfig
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-02-08 10:17:17 -05:00
Stefan Agner
c5343d4e11 arm: imx: mx23: Move MX23 selection to Kconfig
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-02-08 10:17:16 -05:00
Adam Ford
8bbff6a70e Convert CONFIG_MXC_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_MXC_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-08 10:17:16 -05:00
Peng Fan
7a7391fd7e imx: add i.MX8M into Kconfig
Add i.MX8M into Kconfig, create a new folder mx8m
dedicated for i.MX8M.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-02-04 12:00:58 +01:00
Tom Rini
ab21ecef7a Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
 - Some DTS updates
 - ZynqMP psu rework based on Zynq concept
 - Add low level initialization for zc770 and zcu102
 - Add support for Zynq zc770 x16 nand configuration
 - Add mini nand/emmc ZynqMP targets
 - Some arasan nand changes
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
 G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
 =Ylul
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
2018-01-31 07:10:55 -05:00
Michal Simek
93561a327b arm: zynq: Enable DM_GPIO when needed
There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:28:44 +01:00
Michal Simek
c4a142f4a6 arm: zynq: Enable DM_ETH and DM_MMC only if subsystem is enabled
Do not enable DM_ETH/MMC if subsystems are not enabled.
This saves memory for memory constrained boards like cse.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:28:44 +01:00
Michal Simek
099b9ae7b7 arm: zynq: Enable BLK when needed
There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:28:44 +01:00
Alexander Graf
ae5326a6b3 serial: Make full device search optional
Commit 608b0c4ad4 ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.

Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.

Fixes: 608b0c4ad4 ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-29 08:18:02 -05:00
Alexander Graf
cf2c7784bd pl01x: Convert CONFIG_PL01X_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl01x.

Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-28 12:27:35 -05:00
Alexander Graf
d10fc50f78 pl011: Convert CONFIG_PL011_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl011.

Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-28 12:27:35 -05:00
Alexander Graf
884f901368 pl010: Convert CONFIG_PL010_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.

This round goes to pl010.

Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-28 12:27:35 -05:00
Felix Brack
85ab0452fe arm: add support for PDU001
This patch adds support for the PDU001 board.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-28 12:27:32 -05:00
Andre Heider
eff264d731 sunxi: imply CONFIG_OF_LIBFDT_OVERLAY
fdt overlay support is useful for all sunxi boards, enable per default
and remove it from sunxi defconfigs.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-26 20:02:33 +05:30
Ezequiel Garcia
578d95e99f arm: zynq: Enable SPL_CLK only if SPL is enabled
Setup proper dependency in Kconfig for SPL_CLK.
If SPL is not enabled, SPL_CLK shouldn't be selected.

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-24 11:45:06 +01:00
Tuomas Tynkkynen
ddcca73051 ARM: qemu-arm: Add support for AArch64
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:30 -05:00
Bhaskar Upadhaya
b0ce187b1f board: ls1012a: LS1012A-2G5RDB board support
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.

Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 11:56:33 -08:00
Stephen Warren
8163faf952 ARMv8: add optional Linux kernel image header
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12 09:52:11 -07:00
Stephen Warren
e6c904489a ARMv8: Allow dynamic early stack pointer
U-Boot typically uses a hard-coded value for the stack pointer before
relocation. Implement option SYS_INIT_SP_BSS_OFFSET to instead calculate
the initial SP at run-time. This is useful to avoid hard-coding addresses
into U-Boot, so that can be loaded and executed at arbitrary addresses and
thus avoid using arbitrary addresses at runtime. This option's value is
the offset added to &_bss_start in order to calculate the stack pointer.
This offset should be large enough so that the early malloc region, global
data (gd), and early stack usage do not overlap any appended DTB.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12 09:52:11 -07:00
Alison Wang
ab0ab54e49 armv8: Implement workaround for Cortex-A53 erratum 855873
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.

This patch is to implement the workaround for this erratum.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:29:57 -08:00
Michal Simek
2f03968e6c arm64: zynqmp: Enable SPL_CLK when SPL is enabled
Setup proper dependency in Kconfig for SPL_CLK.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14 20:08:21 +01:00
Tuomas Tynkkynen
9fd95ef0d3 ata: Migrate CONFIG_SCSI_AHCI to Kconfig
And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:13:19 -05:00
Michal Simek
b8d4497f99 arm: zynq: Change Zynq/ZynqMP Kconfig description
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:40 +01:00
Philipp Tomsich
14ad6eb264 rockchip: enable boot0-hook for all Rockchip SoCs
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
  instruction load and running by bootrom;

Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-11-21 23:57:21 +01:00
Stephen Warren
49e93875a6 arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17 07:44:13 -05:00
Masahiro Yamada
d6a0c78a4e pylibfdt: compile pylibfdt only when dtoc/binman is necessary
Currently, pylibfdt is always compiled if swig is installed on your
machine.  It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.

"checkbinman" and "checkdtoc" are wrong.  It is odd that the final
build stage checks if we have built necessary tools.  If your platform
depends on dtoc/binman, you must be able to build pylibfdt.  If swig
is not installed, it should fail immediately.

I added PYLIBFDT, DTOC, BINMAN entries to Kconfig.  They should be
property select:ed by platforms that need them.  Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-17 07:43:32 -05:00
Ashish Kumar
91fded6200 armv8: ls1088aqds: Add SD boot support for ls1088qds
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:52:19 -08:00
Ashish Kumar
099f4093a5 armv8: ls1088ardb: Add SD boot support for ls1088
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:51:46 -08:00
Fabio Estevam
07df697e14 mx25: Move MX25 selection to Kconfig
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07 10:12:50 +01:00
Maxime Ripard
ce2e44d836 sunxi: Enable THUMB build for the U-Boot binary
We start to get to the limit of our main U-Boot binary size (with some
boards even crossing it). Enable its build using thumb2 to get some extra
room.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Tuomas Tynkkynen
32f1182926 ARM: Add a new arch + board for QEMU's 'virt' machine
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:

    qemu-system-arm -machine virt,highmem=off -bios u-boot.bin

(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
    - u-boot.bin loaded and executing in the emulated flash at address 0x0
    - A generated device tree blob placed at the start of RAM
    - A freely configurable amount of RAM, described by the DTB
    - A PL011 serial port, discoverable via the DTB
    - An ARMv7 architected timer
    - PSCI for rebooting the system
    - A generic ECAM-based PCI host controller, discoverable via the DTB

Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:

- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
    -drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
    -net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
    -device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
    -drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-06 11:28:16 -04:00
Maxime Ripard
3c989f3a19 sunxi: Fix USB_GADGET implication
USB_GADGET will fail to compile if USB_MUSB_GADGET is not defined. Make
sure we have that condition right.

Fixes: e0ea88042d51 ("sunxi: Imply USB_ETHER")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
a12fb0e368 sunxi: Enable CMD_GPT by default
GPT is pretty common these days and can be useful for things like fastboot.
Add a platform imply, so that users can still opt out if they wish so.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
6e2166c186 sunxi: Imply USB_ETHER
Now that we can enable the usb_ether gadget, do it. This will be especially
useful for boards that don't have any ethernet controller, such as the ones
based on the A13 or A33.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
cfa34996b0 cmd: fastboot: Rework fastboot dependency
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.

That will also reduce the boilerplate in the defconfigs.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
654b02b18c sunxi: imply USB_GADGET
A good number of our boards have USB_GADGET enabled. Imply it so that all
the boards can benefit from it, and remove some boilerplate from our
defconfigs.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Kever Yang
e19fa89c9d rockchip: enable TPL_SYSRESET for all rockchip SoCs
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need TPL_SYSRESET
for do_reset() in TPL for Rockchip SoCs.

References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_)
macro"

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:35 +02:00
Philipp Tomsich
8e8bcccc18 rockchip: imply ADC and SARADC_ROCKCHIP for Rockchip SOCs
Enable the Rockchip SARADC driver for all Rockchip SoCs.

Note that the SARADC peripheral is available on all SoCs except the
RK3036 and RK3228.  However, as this is a DM-driver, enabling by
default will not cause any function problems (and can always be
changed from defconfig, if size is a concern).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
2017-10-01 00:33:31 +02:00
Tom Rini
ff6c3125e7 TI: ARCH_OMAP2PLUS: Enable SPL_STACK_R and provide default value
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it.  select this and re-sync the defconfigs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-29 14:07:51 -04:00
Ashish Kumar
7769776a60 armv8: ls1088aqds: Add support of LS1088AQDS
This patch add support of LS1088AQDS platform.

The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
e84a324ba7 armv8: ls1088ardb: Add support for LS1088ARDB platform
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>

WIP: disable NAND for LS1088ARDB
2017-09-11 08:00:13 -07:00
Kever Yang
0532ceef30 rockchip: enable SPL_SYSRESET config for all Rockchip SoCs
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.

References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-08 11:45:19 +02:00
Tom Rini
48f6232e58 Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
  not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:21 -04:00
Masahiro Yamada
213fcabdfd clk: uniphier: fix unmet direct dependencies warning
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:

  $ make uniphier_v8_defconfig
  warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
  SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)

While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Tom Rini
1fdafb2e3d Merge branch 'master' of git://git.denx.de/u-boot-mmc 2017-08-18 18:24:36 -04:00
Simon Glass
e7881d85a9 dm: mmc: Drop CONFIG_DM_MMC_OPS
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:59:55 +09:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Peng Fan
11d94319c3 arm: Implement workaround for Cortex-A9 errata 845369
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:50:51 +02:00
Simon Glass
c1c3fe2307 env: Convert CONFIG_ENV_IS_IN... to a choice
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).

Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.

Also expand the help for the 'nowhere' option and move it to the top since
it is the default.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-15 20:50:01 -04:00
Philipp Tomsich
b529993e02 spl: add hierarchical defaults for SPL_LDSCRIPT
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.

As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig.  Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:37 +02:00
Adam Ford
5bbc265bec Convert CONFIG_NAND to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-12 09:18:47 -04:00
Simon Glass
72c3033fd1 Convert CONFIG_CMD_SPL to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SPL

Note that trats does not actually use SPL, so this option can no-longer be
set.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:57 -04:00
Simon Glass
15dc63d646 Convert CONFIG_CMD_SAVES to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SAVES

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:55 -04:00
Suji Velupillai
c89782dcac net: move Broadcom SF2 driver to Kconfig
move to Kconfig:
	CONFIG_BCM_SF2_ETH
	CONFIG_BCM_SF2_ETH_DEFAULT_PORT
	CONFIG_BCM_SF2_ETH_GMAC

Also modified defconfigs of all platforms that use these configs.

Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:30 -05:00
Simon Glass
b31e065f89 Convert CONFIG_ENV_IS_IN_FAT to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_FAT

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25 21:34:15 -04:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Tom Rini
d56b4b1974 configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFS
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies.  Migrate these to configs/ from include/configs/.  In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-24 20:35:55 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Simon Glass
fedb428c5b Convert CONFIG_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Jorge Ramirez-Ortiz
d754254f20 ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards
This port adds support for:
        1) Serial
        2) eMMC
        3) USB

It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]

eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.

USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.

PSCI has been tested via the reset call (PSCI executes from DDR)

The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-07-10 14:26:03 -04:00
Andy Yan
f8136e68cc ARM: make memset and memcpy prompt message more clearly
The origin SPL_USE_ARCH_MEMSET/MEMCPY use same prompt message
as USE_ARCH_MEMSET/MEMCPY, which makes it's hard to distinguish
them in menuconfig interface. This patch gives them different
prompt messages for spl and none-spl config.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
2017-06-29 09:51:06 -04:00
Tom Rini
ab43de8036 sunxi: Correct select's of SPL_STACK_R and SPL_SYS_MALLOC_SIMPLE
On ARCH_SUNXI we've been selecting these targets for a long time if
SUPPORT_SPL is set.  However, Lichee Pi Zero is the first platform we've
added that does support SPL but does not build SPL and has exposed a
latent bug.  Both of these symbols depend on SPL not SUPPORT_SPL, so we
need to update our select here otherwise we get a Kconfig warning.

Fixes: f02abb0608 ("sunxi: add support for Lichee Pi Zero")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-21 07:54:46 -04:00
Phil Edworthy
111a6af97a arm: Add Kconfig symbols used for Linux asm compatibility
Rather than change asm files that come from Linux, add the symbols
to Kconfig. Since one of the symbols is for thumb2 builds, make
CPU_V7M always select them.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
2017-06-05 14:13:13 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Daniel Thompson
221a949eb6 Kconfig: Finish migration of hashing commands
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way.  As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
        migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-31 19:38:14 -04:00
Tom Rini
380e86f361 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-05-26 11:19:27 -04:00
Priyanka Jain
3049a583f3 armv8: ls2080ardb: Add LS2081ARDB board support
LS2081ARDB board is similar to LS2080ARDB board with few differences
 It hosts LS2081A SoC
 Default boot source is QSPI-boot
 It does not have IFC interface
 RTC and QSPI flash device are different
 It provides QIXIS access via I2C

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:47:08 -07:00
Simon Glass
551c393446 Convert CONFIG_CMD_HASH to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HASH

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:38:15 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Masahiro Yamada
4aa2ba3a34 mmc: replace CONFIG_GENERIC_MMC with CONFIG_MMC
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature.  Deprecate the
former.

This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-15 18:28:23 +09:00
Tom Rini
a6d4cd4778 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-05-08 15:44:44 -04:00
Nisal Menuka
8776350d87 Add ARM errata workaround 852421 and 852423 for Cortex-A17
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.

Signed-off-by: Nisal Menuka <nisalmenuka23@gmail.com>
2017-05-08 11:57:36 -04:00
Ladislav Michl
a96c08f509 igep0033: Rename to igep003x
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:26 -04:00
Masahiro Yamada
af83a604b3 ARM: sunxi: use imply instead of bare default y in Kconfig
Fix annoying config redefines in SoC/board level Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-05-02 09:20:42 +02:00
Masahiro Yamada
3abfd887e8 ARM: sunxi: move board/sunxi/Kconfig to arch/arm/mach-sunxi/Kconfig
For the consistent location of SoC-level Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-05-02 09:20:30 +02:00
Simon Glass
d315628edb Convert CONFIG_CMD_CLK to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_CLK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:40:58 -04:00
Tom Rini
29ec685883 arm: Re-sync ARCH_MX5 / MX51 / MX53 CONFIG options
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig.  Do so now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:29:38 -04:00
Masahiro Yamada
a93fbf4a78 ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.

Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-27 16:49:08 -04:00
Andrew F. Davis
46f9ef1846 Kconfig: Enable FIT support by default for TI platforms
Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-27 16:49:06 -04:00
Masahiro Yamada
573a3811ed sysreset: psci: support system reset in a generic way with PSCI
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.

The arm-smccc is supported on ARMv7 or later.  Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31.  In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:19 -04:00
Masahiro Yamada
c54bcf6805 ARM: adjust arm-smccc code for use in U-Boot
Adjust ARM SMC Calling Convention code for U-Boot:
  - Replace the license block with SPDX
  - Change path to asm-offsets.h
  - Define UNWIND() as no-op
  - Add Kconfig entry
  - Add asm-offsets

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:17 -04:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Marek Vasut
2a4058c240 ARM: mx5: Rename M53EVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05 18:12:20 +02:00
Marek Vasut
fcea480d1d ARM: mxs: Rename M28EVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05 18:12:04 +02:00
Andre Przywara
85db5831ad sunxi: simplify ACTLR.SMP bit set #ifdef
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Patrice Chotard
584861ffeb reset: Add STi reset support
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device.

Driver code has been mainly extracted from kernel
drivers/reset/sti/reset-stih407.c

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-03-26 13:22:58 -06:00
Dirk Eibach
60083261a1 arm: mvebu: Add gdsys ControlCenter-Compact board
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.

It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.

On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-23 15:48:28 +01:00
Lokesh Vutla
19c1c700ec configs: am43xx_evm: Enable SPL_DM
Enable SPL_DM on all AM43xx based platforms

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-21 07:17:11 -04:00
Jon Mason
274bced86d board: ns2: Add support for Broadcom Northstar 2
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k).  The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
2017-03-20 18:04:43 -04:00
Tom Rini
02ccab1908 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/bk4r1_defconfig
	configs/colibri_vf_defconfig
	configs/pcm052_defconfig
	include/configs/colibri_vf.h
	include/configs/pcm052.h
2017-03-19 15:13:38 -04:00
Stefan Agner
7966b43778 ARM: vf610: move to standard arch/board approach
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19 17:30:11 +01:00
Tom Rini
3a649407a4 arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons.  We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode.  So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2017-03-18 20:28:01 -04:00
Peng Fan
e90a08daee imx: mx7ulp: Add mx7ulp to Kconfig
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Tom Rini
b504ff9f6b Xilinx changes for v2017.05
- Move to DM clk driver
 - Add clk support for zynq_sdhci
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
 /oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
 =JYC5
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2017.05

- Move to DM clk driver
- Add clk support for zynq_sdhci
2017-03-16 16:44:23 -04:00
Patrice Chotard
eee20f8132 STiH410: Add STi SDHCI driver
Add SDHCI host controller found on STMicroelectronics SoCs

On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.

This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.

W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-03-14 20:40:20 -04:00
Patrice Chotard
214a17e61d STiH410: Add STi serial driver
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14 20:40:19 -04:00
Patrice Chotard
94e9a4ef91 arm: Add support for STMicroelectronics STiH410 soc
The STiH410 is an advanced multi-HD AVC processor with 3D
graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU
part of the STiH407 family.

It has wide connectivity including USB 3.0, PCI-e, SATA
and gigabit ethernet.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-03-14 20:40:18 -04:00
Siarhei Siamashka
19a75b8cf8 arm: omap3: Bring back ARM errata workaround 725233
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-14 20:40:17 -04:00
Tom Rini
8dda2e2f9e ARM: Migrate errata to Kconfig
This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:50 -05:00
Tom Rini
0f12f10117 omap4: Migrate to using imply
Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be
using imply instead in arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:16 -05:00
Tom Rini
7551dcf980 omap3: Migrate to using imply
Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be
using imply instead in arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:16 -05:00
Tom Rini
9d4f7a311f TI: Migrate board/ti/common/Kconfig to imply
The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:15 -05:00
Dalon Westergreen
949123e30a SPL: Move SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.

Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2017-02-17 14:15:15 -05:00
Stefan Herbrechtsmeier
781745bd87 zynq: Move zynq to clock framework
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.

Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17 10:22:46 +01:00
Tom Rini
43ade93bdb Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-02-01 16:34:25 -05:00
Marcin Niestroj
ab38bf6a39 board/chiliboard: Add support for chiliBoard
chiliBoard is a development board which uses chiliSOM as its base.

Hardware specification:
 * chiliSOM (TI AM335x, DRAM, NAND)
 * Ethernet PHY (id 0)
 * USB host (usb1)
 * MicroSD slot (mmc0)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-28 14:04:37 -05:00
maxims@google.com
4697abea62 aspeed: Add drivers common to all Aspeed SoCs
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.

Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.

Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-28 14:04:27 -05:00
Marcin Niestroj
d4b1b52737 ARM: imx6ul: Move liteSOM source to SoC directory
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.

[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html

Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:48:07 +01:00
Simon Glass
4585601ae2 Convert CONFIG_ARCH_MISC_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_MISC_INIT

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:41 -05:00
Simon Glass
a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00
Simon Glass
a421192fb8 Convert CONFIG_ARCH_EARLY_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_EARLY_INIT_R

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 16:43:48 -05:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Tom Rini
f428268adb imx31_phycore: Split the eet variant out into a different TARGET
Rename CONFIG_IMX31_PHYCORE_EET to CONFIG_TARGET_IMX31_PHYCORE_EET and
make this a distinct config target.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-24 10:33:53 -05:00
Masahiro Yamada
561ca649a8 ARM: uniphier: make SPL optional for ARVv8 SoCs
We may want to run different firmware before running U-Boot.  For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader.  In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.

This commit removes "select SPL" to make it configurable.  This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI)  Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT.  The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint.  This will mitigate the per-SoC
(sometimes per-board) defconfig burden.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 15:11:12 +09:00
Tom Rini
40d5534cff ARM: Default to using optimized memset and memcpy routines
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel.  We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase.  However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.

Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-20 15:38:01 -05:00
Hou Zhiqiang
dccef2ec01 ls1046ardb: Add support power initialization
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:13 -08:00
York Sun
c01e4a1a6f mmc: move CONFIG_SYS_FSL_ERRATUM_ESDHC* to Kconfig
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-04 19:40:44 -05:00
York Sun
d26e34c4c4 fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-04 19:40:41 -05:00
York Sun
90b80386ff crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to Kconfig
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:19 -05:00
York Sun
2c2e2c9e14 crypto: Move SYS_FSL_SEC_COMPAT into driver Kconfig
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:17 -05:00
Masahiro Yamada
085be482f6 ARM: revive CONFIG_USE_ARCH_MEMCPY/MEMSET for UniPhier and Tegra
Commit be72591bcd ("Kconfig: Move USE_ARCH_MEMCPY/MEMSET to
Kconfig") is misconversion.

The original logic in include/configs/uniphier.h was as follows:

  #if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_ARM64)
  #define CONFIG_USE_ARCH_MEMSET
  #define CONFIG_USE_ARCH_MEMCPY
  #endif

This means those configs were enabled when building U-Boot proper,
but disabled when building SPL.  Likewise for Tegra.

Now "depends on !SPL" prevents any boards with SPL support
from reaching these options.  This changed the behavior for
UniPhier and Tegra SoC family.

Please notice these two options only control the U-Boot proper
build.  As you see arch/arm/Makefile, ARM-specific memset/memcpy
are never compiled for SPL.  So, __HAVE_ARCH_MEMCPY/MEMSET should
not set for SPL.

Fixes: be72591bcd ("Kconfig: Move USE_ARCH_MEMCPY/MEMSET to Kconfig")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-27 11:24:15 -05:00
Tom Rini
8ea05705a7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-12-18 17:43:20 -05:00
Fabio Estevam
be72591bcd Kconfig: Move USE_ARCH_MEMCPY/MEMSET to Kconfig
Move USE_ARCH_MEMCPY/MEMSET options to Kconfig.

Make it "default y" for the ARMv7 architecture and make it
depend on !ARM64 && !SPL.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 07:14:38 -05:00
Marcin Niestroj
727feafebb ARM: imx6ul: Add support for liteSOM
liteSOM is a System On Module (http://grinn-global.com/litesom/). It
can't exists on its own, but will be used as part of other boards.

Hardware specification:
 * NXP i.MX6UL processor
 * 256M or 512M DDR3 memory
 * optional eMMC (uSDHC2)

Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-*
directory and make it possible to reuse initialization code (i.e. DDR,
eMMC init) for all boards that use it.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-12-16 10:31:04 +01:00
Masahiro Yamada
6c498835af ARM: uniphier: remove BLK select
This is a user configurable option, but "select BLK" forces users to
enable it.

Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-11 17:55:13 +09:00
Marek Vasut
beee6a3083 ARM: socfpga: Add boot0 hook to prevent SPL corruption
Valid Altera SoCFPGA preloader image must contain special data at
offsets 0x40, 0x44, 0x48 and valid instructions at address 0x4c or
0x50. These addresses are by default used by U-Boot's vector table
and a piece of reset handler, thus a valid preloader corrupts those
addresses slightly. While this works most of the time, this can and
does prevent the board from rebooting sometimes and triggering this
issue may even depend on compiler.

The problem is that when SoCFPGA performs warm reset, it checks the
addresses 0x40..0x4b in SRAM for a valid preloader signature and
header checksum. If those are found, it jumps to address 0x4c or
0x50 (this is unclear). These addresses are populated by the first
few instructions of arch/arm/cpu/armv7/start.S:

ffff0040 <data_abort>:
ffff0040:       ebfffffe        bl      ffff0040 <data_abort>

ffff0044 <reset>:
ffff0044:       ea000012        b       ffff0094 <save_boot_params>

ffff0048 <save_boot_params_ret>:
ffff0048:       e10f0000        mrs     r0, CPSR
ffff004c:       e200101f        and     r1, r0, #31
ffff0050:       e331001a        teq     r1, #26

Without this patch, the CPU will enter the code at 0xffff004c or
0xffff0050 , at which point the value of r0 and r1 registers is
undefined. Moreover, jumping directly to the preloader entry point
at address 0xffff0000 will also fail, because address 0xffff004.
is invalid and contains the preloader magic.

Add BOOT0 hook which reserves the area at offset 0x40..0x5f and
populates offset 0x50 with jump to the entry point. This way, the
preloader signature is stored in reserved space and can not corrupt
the SPL code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2016-12-06 01:45:56 +01:00
Simon Glass
08848e9c31 arm: samsung: Convert s5p_goni and smdkc100 to DM_I2C
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-05 13:27:29 +01:00
Simon Glass
fc47cf9d05 arm: exynos: i2c: Convert exynos boards to use DM_I2C
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-05 13:27:15 +01:00
Simon Glass
950c3f700c arm: Remove VCMA9 board
This board has not been converted to DM_SERIAL by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-04 13:55:00 -05:00
Simon Glass
fd9080ea50 arm: Remove smdk2410 board
This board has not been converted to DM_SERIAL by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
2016-12-04 13:54:59 -05:00
Tom Rini
4d6647ab17 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-11-30 09:57:52 -05:00
Sebastien Bourdelin
d9e268ed76 ARM: ts4600: add basic board support
This commit adds basic support including:
MMC, Serial console

Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-11-29 16:45:48 +01:00
Fabian Vogt
7670909638 ARM: bcm283x: use OF_CONTROL for bcm283x
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:15:18 -05:00
Yann E. MORIN
2997ee5054 arm: sunxi: do not force USB for arch-sunxi
Currently, USB is forced-enabled for the sunxi familly, and there is no
way to disable it.

However, USB takes a long time to initiliase, delaying the boot by up to
5 seconds (without any USB device attached!). This is a very long delay,
especially in cases where USB booting is not wanted at all, and where
the device is expected to boot relatively often (even in production).

Change the way the dependencies are handled, by only forcibly selecting
USB when CONFIG_DISTRO_DEFAULTS ("defaults suitable for booting general
purpose Linux distributions") is set. This option defaults to y for the
sunxi familly, so the current default behaviour is kept unchanged. Users
interested in boot time and/or size will be able to disable this to
further disable USB.

With USB disabled, the time spent in U-Boot before handing control to
the Linux kernel is about 1s now, down from ~5s (Nanopi Neo, sunxi H3).

Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-11-28 15:10:28 -05:00
Tom Rini
ed77ccd014 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/Kconfig
2016-11-25 17:39:54 -05:00
Alison Wang
ec6617c397 armv8: Support loading 32-bit OS in AArch32 execution state
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.

The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.

Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:40:24 -08:00
Tom Rini
983e37007d arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Tom Rini
272686eb75 arm: Introduce ARCH_OMAP2
To start consolidating various TI-related code, introduce the ARCH_OMAP2
symbol.  While we have removed omap2-specific boards some time ago,
matching up with the kernel naming here will help overall.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:28 -05:00
Feng Li
20c700f8da armv7: Add support of ls1021a-iot board
The patch adds support for Freescale ls1021a-iot board.

Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Tom Rini
3c594d34c4 Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2016-10-12 08:30:38 -04:00
Tom Rini
711b534120 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1021aqds.h
	include/configs/ls1021atwr.h
2016-10-12 08:29:42 -04:00
Masahiro Yamada
4fb96c48c1 reset: uniphier: add reset controller driver for UniPhier SoCs
This is the initial commit for UniPhier reset controller driver.
Most code was ported from Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-10 10:03:23 +09:00
York Sun
fb2bf8c2c6 arm: Move FSL_LSCH2 FSL_LSCH3 to Kconfig
Move these options to Kconfig and create a sub-menu to avoid name
conflict with other architectures.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
Hongbo Zhang
adee1d4c9e ARMv7: LS102xA: Move two macros from header files to Kconfig
Following commits 217f92b and 1544698, these two config
CPU_V7_HAS_NONSEC and CPU_V7_HAS_VIRT are moved to Kconfig,
for correctly select ARMV7_PSCI.

Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 09:56:59 -07:00
Albert ARIBAUD \(3ADEV\)
27192d16eb pcm052: add new BK4r1 target based on PCM052 SoM
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:22:11 +02:00
Tom Rini
51b4a639e4 Merge git://git.denx.de/u-boot-rockchip 2016-10-03 09:09:29 -04:00
Andrew F. Davis
b39a9ade5c Kconfig: Separate AM33XX SOC config from target board config
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.

This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:58 -04:00
Kever Yang
8d29e3a4c4 Kconfig: rockchip: enable DM_PWM and DM_REGULATOR
Enable DM_PWM and DM_REGULATOR on rockchip SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Stefan Roese
21b29fc64e arm64: mvebu: Add basic support for the Marvell Armada 7K/8K SoC
Compared to the Armada 3700, the Armada 7K and 8K are much more on the
high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as
opposed to the Cortex-A53 for the Armada 3700.

The Armada 7K and 8K also use a fairly unique architecture, internally
they are composed of several components:

- One AP (Application Processor), which contains the processor itself
  and a few core hardware blocks. The AP used in the Armada 7K and 8K
  is called AP806, and is available in two configurations:
  dual Cortex-A72 and quad Cortex-A72.
- One or two CP (Communication Processor), which contain most of the I/O
  interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one
  CP, while the 8K family chips integrate two CPs, providing two times
  the number of I/O interfaces available in the CP.
  The CP used in the 7K and 8K is called CP110.

All in all, this gives the following combinations:

- Armada 7020, which is a dual Cortex-A72 with one CP
- Armada 7040, which is a quad Cortex-A72 with one CP
- Armada 8020, which is a dual Cortex-A72 with two CPs
- Armada 8040, which is a quad Cortex-A72 with two CPs

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support,
starting with the Marvell DB-88F7040 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
f61aefc150 arm64: mvebu: Add support for the Marvell Armada 3700 SoC
The Armada 3700 integrates the following interfaces (not complete list):
- Dual Cortex-A53 ARMv8
- USB 3.0
- SATA 3.0
- PCIe 2.0
- 2 x Gigabit Ethernet 1Gbps / 2.5Gbps
- ...

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support
for the Marvell DB-88F3720 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Tom Rini
cbe7706ab8 Merge git://git.denx.de/u-boot-fsl-qoriq
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-26 17:10:56 -04:00
York Sun
5e8bd7e117 armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig option
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
York Sun
0a37cf8f27 Convert CONFIG_SYS_FSL_ERRATUM_A010315 to Kconfig option
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
2016-09-26 08:53:07 -07:00
York Sun
9533acf36c armv8: ls1012a: Convert CONFIG_LS1012A to Kconfig option ARCH_LS1021A
Move this config to Kconfig option and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
York Sun
da28e58a7f armv8: ls1046a: Convert CONFIG_LS1046A to Kconfig option ARCH_LS1046A
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
Tom Rini
201c9d884d Merge git://git.denx.de/u-boot-rockchip 2016-09-22 16:51:19 -04:00
Masahiro Yamada
0298f4c003 ARM: uniphier: move CONFIG_SPL_* to defconfig or select
As I repeated in the ML, I am unhappy with config entries with bare
defaults.  Kick them out of arch/arm/mach-uniphier/Kconfig.

Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable
(build fails without it), but it should be fixed later anyway,
so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-23 00:38:38 +09:00
MengDongyang
892742df1f rockchip: select DM_USB for rockchip SoC
Select DM_USB to compatible with USB DM driver model.

Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-09-22 07:32:22 -06:00
Masahiro Yamada
27350c922e ARM: uniphier: select PINCTRL and SPL_PINCTRL
Now all UniPhier SoCs support a pinctrl driver.  Select (SPL_)PINCTRL
since it is mandatory even for base use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:35 +09:00
Shaohui Xie
126fe70d77 armv8: ls1046aqds: Add LS1046AQDS board support
LS1046AQDS Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:11:10 -07:00
Mingkai Hu
dd02936f81 armv8: ls1046ardb: Add LS1046ARDB board support
LS1046ARDB Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 512 Mbyte NAND flash
 * Two 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card
 * On-board 4G eMMC

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe:
 * PCIe1 (SerDes2 Lane0) to miniPCIe slot
 * PCIe2 (SerDes2 Lane1) to x2 PCIe slot
 * PCIe3 (SerDes2 Lane2) to x4 PCIe slot

SATA:
 * SerDes2 Lane3 to SATA port

USB 3.0: one super speed USB 3.0 type A port
	 one Micro-AB port

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:11:00 -07:00
Masahiro Yamada
14f4723466 mmc: uniphier-sd: migrate to CONFIG_BLK
This is the state-of-the-art MMC driver implementation.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-14 22:54:19 +09:00
Masahiro Yamada
47a79f657e usb: uniphier: remove UniPhier xHCI driver and select DM_USB
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers.  Remove it for now.

The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.

These two changes must be done atomically because removing the
legacy driver causes a build error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-09-14 22:54:19 +09:00
Masahiro Yamada
b5550e496e ARM: uniphier: sort select:s alphabetically
ARCH_UNIPHIER is having more and more select:s.  Sort them in case
a select is accidentally duplicated.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14 22:54:19 +09:00
Masahiro Yamada
174245b909 ARM: am335x: select DM_GPIO
We are supposed to not add config entries with only "default y"
in board/SoC Kconfig files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2016-09-07 08:48:58 -04:00
Masahiro Yamada
217f92bb79 ARM: armv7: move CONFIG_ARMV7_PSCI to Kconfig
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select.  Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.

Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07 08:48:51 -04:00
Tom Rini
e009bfa4f9 arch/arm/Kconfig: Whitespace correction
Use a tab not 8 spaces.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-26 17:04:55 -04:00
Tom Rini
067716bac5 ARM: Move SYS_CACHELINE_SIZE over to Kconfig
This series moves the CONFIG_SYS_CACHELINE_SIZE.  First, in nearly all
cases we are mirroring the values used by the Linux Kernel here.  Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux).  Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
2016-08-26 17:04:46 -04:00
Tom Rini
c98b171e10 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
[trini: Drop CMD_BOOTI as it's now on by default on ARM64]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-20 16:40:34 -04:00
Nobuhiro Iwamatsu
7a500a7a78 ARM: rmobile: Create R-Car 32bit (Gen1 and Gen2) for Kconfig
This creates Kconfig of R-Car 32bit for Kconfig of R-Car 64bit (Gen3).

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-08-17 10:25:34 +09:00
Nobuhiro Iwamatsu
1cc95f6e1b ARM: Rmobile: Rename CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-08-17 10:25:34 +09:00
Nobuhiro Iwamatsu
badbb63c2c ARM: rmobile: Move SoC sources to mach-rmobile
Move from arch/arm/cpu/armv7/rmobile/ to arch/arm/mach-rmobile/.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-08-17 10:25:28 +09:00
Tom Rini
7d106242d3 omap3, omap4: Enable USE_TINY_PRINTF for all
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler.  Move to USE_TINY_PRINTF
to give them more room.  OMAP4 will soon enough be in a similar place,
so enable that now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 07:27:29 -04:00
Tom Rini
a2ea62e826 omap3: Move to select SUPPORT_SPL for all
In reality all omap3 platforms support SPL so move the select for this
up a level.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 07:27:29 -04:00
Masahiro Yamada
bb6b142fc1 treewide: move CONFIG_PHYS_64BIT to Kconfig
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system.  Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.

Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.

I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable.  However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones.  I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.

CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.

Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-05 07:27:25 -04:00
Michal Simek
28559d4c93 ARM64: zynqmp: Do not enable DM_MMC by default
The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1: 329a449f2c)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.

Move options to defconfig instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-08-02 07:19:09 +02:00
Simon Glass
329a449f2c dm: mmc: zynq: Convert zynq to use driver model for MMC
Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
dec49e862e dm: zynq: usb: Convert to CONFIG_DM_USB
Convert zynq USB to driver model. Note this is tested on zynq-zybo only.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Kever Yang
a381bcf529 ARM64: rockchip: add support for rk3399 SoC based evb
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:46:45 -06:00
Andreas Färber
e0f5dbcb4b rockchip: Clean up CPU selection
In preparation for RK3368 and RK3399, which need to select ARM64, don't
select CPU_V7 at the ARCH_ROCKCHIP level but at the SoC level instead.

Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:19 -06:00
Michal Simek
1f29738ad1 ARM64: zynqmp: Enable CLK and SPL_CLK by default
Serial driver starts to use clk framework that's why
enable it by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22 14:03:54 +02:00
Simon Glass
42b37d8d46 dm: mmc: rockchip: Enable CONFIG_DM_MMC_OPS for all boards
Enable this option to move rockchip over to use driver model for MMC
operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-11 14:06:44 -06:00
Simon Glass
aa15038cdf rockchip: Use 'select' instead of defaults in Kconfig
Rockchip uses driver model for all subsystems. Specify this in the arm
Kconfig rather than as defaults in the Rockchip Kconfig. This means that
boards cannot turn these options off, which seems correct.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-11 14:06:44 -06:00
Hannes Schmelzer
a4d799939f board/BuR: rename kwb board to brxre1
Rename B&R kwb board to brxre1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24 17:24:40 -04:00
Hannes Schmelzer
2290fe0642 board/BuR: rename tseries board to brppt1
Rename B&R tseries board to brppt1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24 17:24:39 -04:00
Hans de Goede
9f823615af Kconfig: Add a new DISTRO_DEFAULTS Kconfig option
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.

The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.

The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.

For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 21:30:13 -04:00
Hans de Goede
8c7d22965d sunxi: Select USE_TINY_PRINTF
This gives us a bit more breathing room wrt our SPL size.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-20 22:43:59 +02:00
Masahiro Yamada
51ea5a060d ARM: uniphier: reserve memory for DRAM PHY training on PH1-LD20
The DRAM PHY layer on PH1-LD20 is able to calibrate PHY parameters
periodically.  This compensates for the voltage and temperature
deviation and improves the PHY parameter adjustment.  Instead, it
requires 64 byte scratch memory in each DRAM channel for the dynamic
training.  The memory regions must be reserved in DT before jumping
to the kernel.

The scratch area can be anywhere in each DRAM channel, but the DRAM
init code in SPL currently assigns it at the end of each channel.
So, it makes sense to reserve the regions on run-time by U-Boot
instead of statically embedding it in the DT in Linux.  Anyway,
a boot-loader should know much more about memory initialization
than the kernel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-20 07:15:33 +09:00
Heiko Schocher
71423435fb arm, am335x: siemens: enable DM/DTS support
enable basic DM/DTS support for the siemens am335x based boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-17 09:51:05 -04:00
Eddy Petrișor
9702ec00e9 armv8: s32v234: Introduce basic support for s32v234evb
Add initial support for NXP's S32V234 SoC and S32V234EVB board.

The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.

Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>

Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
2016-06-13 08:56:35 -04:00
Steve Rae
43486e4cd0 board: arm:: Add support for Broadcom BCM23550
Add support for the Broadcom BCM23550 board.

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-13 08:56:02 -04:00
Heiko Schocher
6b3943f1b0 siemens,am33x: add draco etamin board
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:13 -04:00
Heiko Schocher
d8ccbe93b5 am335x, shc: add support for the am335x based bosch shc board
U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06)
SHC C3-Sample
MPU reference clock runs at 6 MHz
Setting MPU clock to 594 MHz
Enabling Spread Spectrum of 18 permille for MPU
Trying to boot from MMC
reading u-boot.img
reading u-boot.img

U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100)

       Watchdog enabled
I2C:   ready
DRAM:  512 MiB
reloc off 1f783000
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net:   cpsw
U-Boot#

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:10 -04:00
Tom Rini
d77fa2ff76 Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig
2016-06-06 13:39:43 -04:00
Andre Przywara
cdaa633fcf arm/arm64: implement a boot header capability
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.

Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
  .space 1000
  .word 0x12345678

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
  start.S (arm64) and
  vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).

For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.

[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-06 13:39:19 -04:00
Tom Rini
c41c649c2f Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-06-04 08:49:08 -04:00
Prabhakar Kushwaha
ff78aa2ba1 armv8: ls1012a: Add support of ls1012afrdm board
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Prabhakar Kushwaha
3b6e3898c2 armv8: ls1012a: Add support of ls1012ardb board
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Prabhakar Kushwaha
9d044fcb8c armv8: ls1012a: Add support of ls1012aqds board
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Marek Vasut
66020a67c1 arm: config: Introduce CONFIG_SYS_ARM_ARCH
Introduce new helper Kconfig option, which is automatically set to
the version of ARM architecture for which the U-Boot is built. This
is useful when selecting tuning options in the libgcc imported from
Linux kernel.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-02 21:21:43 -04:00
Marek Vasut
b4ba1693ef arm: Select CONFIG_ARM64 for Cavium ThunderX
Select the config option, since this board is ARM64.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2016-06-02 21:21:42 -04:00
Madan Srinivas
a774e08858 ti: omap-common: Add Kconfig file for secure device support
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.

This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.

With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
6384726d2d arm: Kconfig: Add support for AM43xx SoC specific Kconfig
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.

This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.

Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Beniamino Galvani
bfcef28ae4 arm: add initial support for Amlogic Meson and ODROID-C2
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].

[1] https://patchwork.ozlabs.org/patch/603583/

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 15:39:47 -04:00
Hans de Goede
0878a8a7db sunxi: Enable a bunch of commands by default on sunxi
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.

Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25 17:52:39 +02:00
Thomas Abraham
36aa893775 arm: exynos: realign the code to allow support for newer 64-bit platforms
The existing Exynos 32-bit platform support needs to be realigned in
order to support newer 64-bit Exynos platforms. The driver model will
be utlized for drivers on the 64-bit Exynos platforms and so some of
the older platform support code would not be required for the newer
64-bit Exynos platforms.

Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 10:00:19 +09:00