Currently by running the following test:
=> setenv bootcmd reset
=> save
=> reset
, we observe a hang after approximately 20-30 minutes of stress reboot test.
Investigation of this issue revealed that when a single DDR chip select is used,
the hang does not happen. It only happens when the two chip selects are active.
MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":
"The controller must keep the memory lines quiet (except for CK) for the ZQ
calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256
for other ZQCL and 64 for ZQCS)."
According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:
"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines.
Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"
So make sure to activate one chip select at time (CS0 first and then CS1 later),
so that the required JEDEC delay is respected for each chip select.
With this change applied the board has gone through three days of reboot stress
test without any hang.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since a clock function setup_gpmi_io_clk is implemented for GPMI
IO clock settings, change to use this common function in GPMI setup.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021AQDS board.
For ls1021aqds_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the CH7301 HDMI options and the common configuration
for DCU on LS1021AQDS board.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Cc: Jason Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch configures and initializes the L2 switch on T1040rdb board.
The external L2 switch ports may be connected to PHYs only over
QSGMII, for T1040rdb.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
This patch configures and initializes the L2 switch on T1040QDS board.
The L2 switch ports must be initialized according to the SerDes
protocols.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit 1f98e31bc0 ("imx: mx6sxsabresd: Use the pfuze common init
function") board_late_init() became empty, so we can safely remove this unneeded
function.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB-PB board adds 2.5G SGMII support with AQR105 PHY.
rcw_0x095 is used for 10G XFI + 3x PCIex1
rcw_0x135 is used for 2.5G SGMII + 2x PCIex1
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Besides, added SPI/SD/NAND boot deep sleep support.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure boot target is added for T1042RDB platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes 2 protocol 56 is not valid any longer due to
the new RCW; protocol 55 is used instead, so add
SerDes 2 protocol 55 to align with RCW.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR and SPI flash secure boot target for C29XPCIE board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.
Let's get rid of get_board_rev() as it is not being used with its correct
meaning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains
selection bits and connected status bit. So the Corresponding mux
value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new device trees use a more generic interface for
supporting muxing mdio buses. The mux property is thus
specified in "reg", rather than "fsl,hydra-mdio-muxval".
In order to support using old device trees, we keep the
old fixup in there. Linux will therefore see the both
properties, but will ignore fsl,hydra-mdio-muxval.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.
To enable XFI via SFP use the below hwconfig:
fsl_b4860_serdes2:sfp_amc=sfp
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since xfi has no phy, we delete the property "phy-handle" and use
a "fixed-link" property for a xfi port.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or
SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1
as other functionality except RGMII. The workaround is to select
ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use these new functions where possible. They default to a value of 2 so we
cannot use them in some places where we need a default value of 1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Modify the pfuze init for mx6sxsabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Modify the pfuze init for mx6sabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Since the Pfuze initializations are similar on various mx6 SABRE
boards. Factorize the initialization to a common function in file
board/freescale/common/pfuze.c. So that all SABRE boards BSP can
share the function.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
In U-boot it is preferred to access the register via structure pointer, so
convert it such style.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid
getting a warning that the mx6sabresd_spl is not maintained.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Many boards use a minimal .cfg file in the SPL case.
Introduce spl_sd.cfg so that we can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The PFUZ probe failed with the following msg:
" wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=0
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=1
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=2
i2c_init_transfer: give up i2c_regs=021a0000
Can't find PMIC:PFUZE100 "
board_early_init_f is too early to call i2c related setting, because
init_func_i2c is called after board_early_init_f being invoked. Thus
move setup_i2c into board_init.
Also PFUZ is connected to I2C bus 0, so change "1" -> "0".
Using this patch PFUZ can be correctly probed:
"PMIC: PFUZE100 ID=0x11"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX
mode. By default, the lane runs in SGMII mode, when a MAC uses a lane
in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set,
and needs to fixup dtb accordingly for kernel to do proper initialization.
Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC
1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a
MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx",
'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc.
If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below
setting:
fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: Fix compiling warning]
Reviewed-by: York Sun <yorksun@freescale.com>
XFI ports on t2080qds can work with fiber cable and direct attach
cable(copper). We use hwconfig to define cable type for XFI, and fixup
dtb based on the cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4.
fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3
stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four
<10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if
a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6sxsabresd board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to make host port work in HOST mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The config targets described in README are not present
any more, update the info to currently used targets.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The "S: Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")
For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
N
/S:[[:blank:]]Orphan/s/^/#/
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
