This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Changes to mvpp2.c require the MVMDIO module which in turn uses
DM_MDIO.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.
This patch fixes the issue with the link always down on MCBIN board.
nhed: added NULL deref test.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Issue:
- Network stuck if autonegotion fails.
Issue root cause:
- When autonegotiation fails during port open procedure, the packet
processor configuration does not finish and open procedure exits
with error.
- However, this doesn't prevent u-boot network framework from
calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
processor will cause traffic to get stuck.
Fix:
- Continue packet processor configuration even if autonegotiation
fails. Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
indication.
- U-boot network framework now calls open procedure again during next
transmit initiation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Refactor SGMII configuration to group all settings together and reduce
number of MDIO transactions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.
The driver would only set the IO impedance value when RGMII internal delays
were enabled. There is no reason for this. Move the IO impedance block
out of the RGMII delay block.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.
The current code is assuming the reset default of the delay control
register was to have delay disabled. This is what the datasheet shows as
the register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.
Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this. It could be used to daisy-chain PHYs, but
this is uncommon. Since the PHY can disable the output, make doing so an
option. I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).
Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver ti.c is actually driver for TI DP83867x PHYs, so rename it
accordingly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: tetsu-aoki via github
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):
$ ./tools/buildman/buildman -b video-wip -sS wandboard
...
01: Merge git://git.denx.de/u-boot-sh
02: video: add guards around 16bpp/32bbp code
03: video: make BPP and ANSI configs optional
arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Many boards use only single depth configuration, for such boards
there is some unused code in video and console uclass routines.
Add guards to avoid dead code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
The 24MHz oscillator clock is referenced by "clock-osc-24m" and not
"osc_24m".
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In case the BMP size is bigger than the frame buffer, don't use
the BMP's width and height in video_display_rle8_bitmap, but the
one's checked in video_bmp_display() as parameters to
video_display_rle8_bitmap().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CC: Yannick Fertré <yannick.fertre@st.com>
Convert panel_picture_delta and axis_alignment from unsigned long
to long to insure to store correctly the difference between
panel_size and picture_size in case the panel_size is smaller
than picture_size.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CC: Yannick Fertré <yannick.fertre@st.com>
[agust: change axis_alignment to long]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
An iomux register contains 8 pins, each of which is represented
by 2 bits, but the register offset is 0x8.
For example, GRF_GPIO0A_IOMUX offset is 0x0, but GRF_GPIO0B_IOMUX
offset is 0x8, the offset 0x4 is reserved.
So add a type IOMUX_8WIDTH_2BIT to calculate offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the glue code to allow the rk3308 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The mmc CID value is one of the input parameters used to provision the
RPMB key. The trusted execution environment expects this value to be
specified in big endian format.
Before this fix, on little endian systems, the value returned by the
linux kernel mmc driver differed from the one returned by u-boot.
This meant that if linux provisioned the RPMB key, u-boot would not
have access to the partition (and the other way around).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
CONFIG_DFU_NAND needs the raw NAND core being compiled.
Also fix the colibri_vf defconfig to reflect this dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add null pointer check to take care of out of memory errors.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The MMC boot is currently broken on omapl138-lcdk after enabling the
driver model in SPL. The main problem is the driver's bind callback not
being called after probe in SPL (even with the DM_FLAG_PRE_RELOC flag
specified).
While a proper fix is still being worked on, this hacky changeset at
least fixes the MMC boot on this platform by calling mmc_bind()
manually from probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
struct mmc_config & struct mmc don't need to be exported over platform
data, but can instead be private in the driver.
Remove struct davinci_mmc_plat.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set. In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
The array 'mtd_table' is unused in the code. Remove this as gcc doesn't
always discard unused global variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
The content of pci_rom.c is only used in a few cases. Only build and
link in these cases to avoid a global variable as gcc doesn't always
discard those when they are unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
Make the at91_gpio driver set sensible GPIO bank names in the platform
data. This makes the 'gpio status' command a lot more useful.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function header to serial.h since this function is clearly
related to serial. The function itself stays in console.c since we don't
have a single serial file. DM and non-DM each has a separate file so we
would have to either create a new common serial file, or repeat the
function in both serial.c and serial-uclass.c, neither of which seem
worthwhile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function declarations in serial.h are not in sync with what is
currently used in usbtty. Fix this by updating the header and including
it, to help catch future such problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have an existing U-Boot header for the one function that this defines.
Use that instead of the linux/ one. Move over the nice comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a few whitespace problems with this code. Tidy them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is only used by a few files so it should not be in the common header.
Move it out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With commit f0921f5098 ("fdt: Sync up to the latest libfdt"),
SiFive Unleashed board does not boot any more. This was due to
the U-Boot local changes commit 77d7fff8ce ("fdt: Fix handling
of paths with options in them") to libfdt/fdt_ro.c was dropped
during the libfdt upgrade.
>From the history [1] it was mentioned that the U-Boot changes
commit 77d7fff8ce ("fdt: Fix handling of paths with options in
them") was rejected by libfdt upstream, hence we need find another
way to fix the things.
This commit uses another method, by updating serial_check_stdout()
directly to handle the situation of "stdout-path" with ":options".
A simpler way is to change the logic in fdtdec_get_chosen_node()
to do similar thing, but I feel that not every property in chosen
node may have the option in them, hence it would make more sense
to do the special handling in serial_check_stdout() directly.
[1]: http://patchwork.ozlabs.org/patch/462756/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Check SCC for errors after check command if applicable and
optionally adjust the bus skew settings accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the auto-retuning in HS400 mode in favor of manual calibration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the TMPPORT3 offsets according to the latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the DT2FF offsets in HS400 according to latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The M3W up to ES1.2 uses 4 tuning taps for HS400, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch is to get clock directly from global data.
- Remove uclass clk api method. This was what i.MX platforms were
using, while QorIQ platforms weren't.
- Get clock only from global data, dropping mxc_get_clock().
QorIQ eSDHC controllers on one silicon use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Allow the unit test to pass full 8 byte scan code sequences to the USB
keyboard emulation driver and to parse multi-byte escape sequences.
The following features are not yet tested:
* LED status
* caps-lock
* num-lock
* numerical pad keys
The following features are not yet implemented by the USB keyboard
driver and therefore not tested:
* modifiers for non-alpha-numeric keys, e.g. <SHIFT><TAB> and <ALT><F4>
* some special keys, e.g. <PRINT>
* some modifiers, e.g. <ALT> and <META>
* alternative keyboard layouts
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide support for F1-F12, Insert, Delete, Home, End, Page Up, Page Down.
As this leads to a size increase provide a customizing setting
CONFIG_USB_KEYBOARD_FN_KEYS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit ec3dcea744 ("video: mxsfb: Configure the clock after eLCDIF reset")
causes boot regression on imx7d-pico/imx7d-sdb boards, so revert it
until a better solution is prepared.
This reverts commit ec3dcea744.
Reported-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi 4 upstream kernel device tree instroduces
a new compatible for the pinctroller. Add this to the driver
so that we can boot with the upstream kernel DT.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Rockchips dwmmc controllers can't do dma to non-ddr addresses,
like for example the soc-internal sram but during boot parts of
TrustedFirmware need to be placed there from the read FIT image.
So add handling for a u-boot,spl-fifo-mode to not put the mmc
controllers into fifo mode for all time.
The regular fifo-mode property still takes precedent and only
if not set do we check for the spl-specific property.
Suggested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add 0x330c for rk3399 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot has two different variants of dwc3 initializations,
- with dm variant gadget, so the respective dm driver would
call the dwc3_init in core.
- with non-dm variant gadget, so the usage board file would
call dwc3_uboot_init in core.
The driver probe would handle all respective gadget properties
including phy interface via phy_type property and then trigger
dwc3_init for dm-variant gadgets.
So, to support the phy interface for non-dm variant gadgets,
the better option is dwc3_uboot_init since there is no
dedicated controller for non-dm variant gadgets.
This patch support for adding phy interface like 8/16-bit UTMI+
code for dwc3_uboot.
This change used Linux phy.h enum list, to make proper code
compatibility.
Cc: Marek Vasut <marex@denx.de>
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Technically the default mmc device for fastboot would
use eMMC if the board support for it.
Rockchip platform access device 0 for eMMC so, use the
same device number for rk3328.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add 0x310c for rk3128 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fan53555_regulator_set_value() passes its own dev to pmic_clrsetbits()
instead of its parent (pmic). As result u-boot crashes when you try to
set voltage on fan53555 regulator
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
That's not correct and it breaks SMBUS-style reads and and writes for
some chips (e.g. SYR82X/SYR83X).
Stop bit should be sent only after the last message.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SYR82X and SYR83X are almost identical to FAN53555, the only difference
is different die ID and revision, voltage ranges and steps.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting dwc2_fifo_read to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting two functions to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
To use this DM timer on socfpga as system tick, it needs to take itself
out of reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Make the function pointer struct const, as it does not need to be
writable. This doesn't really change anything other than moving this
variable to a different section. No functional change.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
We only need to build and link input.o when we have any of
CONFIG_KEYBOARD, CONFIG_DM_KEYBOARD (and SPL/TPL variants) or
CONFIG_TEGRA_KEYBOARD set.
Signed-off-by: Tom Rini <trini@konsulko.com>
xhci.h has now been moved to include/usb/ directory. Therefore, update the
path in the Cadence USB drivers.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DM support for Silicon(SIL3131 / SIL3132 / SIL3124) sata driver as
few of the PowerPC platforms such as P series based boards need to
use SATA_SIL with DM,
Also fix below warning while PowerPC P series boards compilation,
===================== WARNING ======================"
This board does use CONFIG_LIBATA but has CONFIG_AHCI not"
enabled. Please update the storage controller driver to use"
CONFIG_AHCI before the v2019.07 release."
Failure to update by the deadline may result in board removal."
See doc/driver-model/MIGRATION.txt for more info."
===================================================="
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add DM support for Freescale PowerPC sata driver used for PowerPC T series
SoCs,
CONFIG_BLK needs to be enabled on these platforms. It adds the SATA
controller as AHCI device, which is strictly speaking not correct,
as the controller is not AHCI compatible, But the U-Boot AHCI uclass
interface enables the usage of this DM driver,
Also fix below warning while PowerPC T series boards compilation,
===================== WARNING ======================"
This board does use CONFIG_LIBATA but has CONFIG_AHCI not"
enabled. Please update the storage controller driver to use"
CONFIG_AHCI before the v2019.07 release."
Failure to update by the deadline may result in board removal."
See doc/driver-model/MIGRATION.txt for more info."
===================================================="
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXdJyOg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOmuAJ9lF7GyPpv0vZNX1V4UV2EyyOOdbwCfQzHu3Xo+
3VWLV9ZHkVMlfnGbbx0=
=+YuG
-----END PGP SIGNATURE-----
Merge tag 'video-for-v2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
A dm based dram driver for rk3308 u-boot
to get capacity.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clk controller driver for RK3308 SOC.
This patch depends on Elaine's pll patch[0].
[0]http://patchwork.ozlabs.org/patch/1183718/
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Common PLL setup function, compatible with different SOC.
Mainly for the subsequent new SOC use.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_IS_ENABLED() needs the config name like used in Kconfig, so
without the leading CONFIG_. The clock drivers all wrongly check for
CONFIG_RESET_ROCKCHIP, fix that
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_reset_bind() already does the needed init for the reset
registers, only referenced the wrong cru structure.
So we can get rid of the open-coded reset init and just fix
the correct cru reference.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Newer Rockchip socs like the px30 use a different ip block to handle
one-time-programmable memory, so add a misc driver for it as well.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the glue code to allow the px30 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the necessary glue code to allow pinctrl setting on px30 socs.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are some code different with rockchip vendor code which may lead
to different bugs, including:
1) Fix setting error about LPDDR3 dram size ODT.
2) Set phy io speed to 0x2.
3) Fix setting error about phy_pad_fdbk_drive.
4) Fix setting error about PI_WDQLVL_VREF_EN
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update the calculation of the stride to support all the DRAM case.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The io setting are updated after some bugfix in different rk3399 boards,
sync the code from vendor.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update lpddr timing in lpddr4-400 and lpddr4-800 file from rockchip
vendor code;
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add capacity detect for rk3399 so that the driver able to detect the
capacity automatically.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up the sdram_init to keep sync with rockchip source code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up rk3399 dram driver source code for more readable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The debug info for dram is main about the capacity related info which is
very important the board init, so set this default enable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The functions for dram info print are part of common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The header file sdram.h is used for rk3288 and similar SoCs, rename it
to make it more understandable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Remove the pinctrl_decode_pin_config() API, because this
function is unused and not compatible with livetree
(it uses fdtdec_get_bool instead of ofnode API).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the compatible "synopsys,dw-mipi-dsi" added in U-Boot
(it don't exist in Linux kernel binding); it is only used
to bind the generic synopsys UCLASS_DSI_HOST "dw_mipi_dsi" to
the driver "stm32-display-dsi" UCLASS_VIDEO_BRIDGE
This binding is done in Linux kernel drivers without compatible
(dw_mipi_dsi_bind() is called in bind of driver, for example in
drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c).
This patch does the same in U-Boot driver, the STM32 driver
calls during its bind the function device_bind_driver_to_node
to bind the generic driver "dw_mipi_dsi" at the same address.
This patch reduces the device tree differences
between Linux kernel and U-Boot for stm32mp1 platform.
Tested with v2020.01-rc1 on STM32MP157C-EV1 and STM32MP157C-DK2.
The dependency of driver is clearer and the probe order is guaranteed.
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
sysreset 0 [ ] syscon_reboot |-- reboot
simple_bus 0 [ + ] generic_simple_bus |-- soc
serial 0 [ + ] serial_stm32 | |-- serial@40010000
...
video_brid 0 [ + ] stm32-display-dsi | |-- dsi@5a000000
dsi_host 0 [ + ] dw_mipi_dsi | | |-- dsihost
panel 0 [ + ] rm68200_panel | | `-- panel-dsi@0
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
Running stress reboot test on a i.MX6ULL evk board with a
custom LCD can lead to splash screen failure (black screen).
After comparing the eLCDIF initialization with the Linux kernel
driver, it was noticed that the eLCDIF reset is the first operation
that needs to be done.
So do like the eLCDIF Linux driver and move the eLCDIF clock
frequency configuration after the eLCDIF reset and just prior to
setting the RUN bit.
With this change applied, no more black screen issues has been
found during overnight reboot stress tests.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Fix a typo that caused incorrect values to be loaded into the DRAM
controller's deskew registers.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix a pair of tests in phy_dll_bypass_set() that used incorrect units
for the DDR frequency, causing the DRAM controller to be misconfigured
in most cases.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a call to rk3328_configure_cpu() during initialization to set the
CPU-clock frequency.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK809 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(5*BUCKs, 9*LDOs, 2*SWITCHes)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK817 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1* BOOST, 9*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK805 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 3*LDOs)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK816 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1*BOOST, 6*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to adapt the following pmics, make the interface more compatible.
Support buck and ldo suspend voltage setting and getting.
Supprot buck and ldo suspend enable/disable setting and getting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the SPI_FLASH_BAR for the ESPI controller of FSL, this entry
is missed by
commit 6d82517836 ("configs: Don't use SPI_FLASH_BAR as default")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The xHCI 1.1 version also need set Transfer Type field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the missing RGMII PHY modes in which case the MAC has configure its
RGMII settings. The only difference between these modes is the RX and
TX delay configuration. A user might choose any RGMII mode in the device
tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The saved ofnode is used by some PHY drivers to access the device tree
node of the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In ls_pcie_ep_enable_cfg(), as part of EP setup,config ready bit
of pci controller is set, so that RC can read the config space of EP.
While setting the config ready bit, LTSSM_EN bit in same register was
also inadvertently getting cleared. This restarts the link training
between RC and EP.
Update code to just set the desired CFG_READY bit (bit 0),
while leaving the other bits unchanged.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
j721e SoCs have different OPP tables. Add support for the same.
Note: DM Still has lot of voltages TBD hence the correct
values need to be programmed once they are published.
Signed-off-by: Keerthy <j-keerthy@ti.com>
TPS6236x is a family of step down DC-DC converters optimized for battery
powered portable applications for a small solution size. Add a regulator
driver for supporting these devices.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize
the operating voltage based on characterization data written to efuse
during production. Add a driver to support this feature for K3 line of
SoCs, initially for AM65x.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
To add usb-3.0 support to peripheral device add BOS & SS capability
descriptors to gadget composite framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Add a new bcdDevice entry for Cadence USB gadget controller similar to
other controller and add gadget_is_cdns3() macro as well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add driver to handle TI specific wrapper for Cadence USB3 controller
present on J721e SoC. Based on Linux driver for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Implement udc_set_speed() callback to limit Controller's speed to
high-speed/full-speed when working with gadgets that are high-speed or
full-speed only
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[jjhiblot@ti.com: Add PHY support]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch was copied from kernel commit: 67fdfda4a99ed.
Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver because that will just fail.
So here introduce a new optional ->udc_set_speed() method which can be
implemented by interested UDC drivers to achieve this purpose.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add match_ep() op to usb_gadget_ops similar to Linux kernel which is
useful in finding a suitable ep match for the function driver. This will
avoid adding more gadget_is_xxx() handling code to usb_ep_autoconfig().
Also sync usb_ep_caps struct thats is usually used in the match_ep()
callback by the gadget controller driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add more clks for fec_mxc according to Linux Kernel 5.4.0-rc1
drivers/net/ethernet/freescale/fec_main.c.
Since i.MX8MQ not support CLK_CCF, so add a check to restrict
the code only effect when CONFIG_IMX8M and CONFIG_CLK_CCF both defined.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined
in defconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add set_parent callback, then assigned-clock-parents in dts could
be work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add enet ref/timer/PHY_REF/root clk which are required to make enet
function well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add i.MX8MM ccf driver support.
Modifed from Linux Kernel 5.3.0-rc1, drop some entries
that not used in U-Boot and adapt to U-Boot CCF style.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Lukasz Majewski <lukma@denx.de>
The power domain tree is not accepted by Linux Kernel upstream.
only a single pd node is used currently, as following:
pd: imx8qx-pd {
compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd";
#power-domain-cells = <1>;
};
So to migrate to use upstream linux dts, we also need a driver
to support this.
This patch is to support the new method, compared with legacy power
domain tree, it will be simpiler, because each device will
has resource id as power domain index, it will be directly passed
to scfw, and no need to let power domain build that tree. If multiple
power domain is needed, it is the dts node should has correctly power
domains entry added and sequence correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current i.MX8 power domain driver is based on i.MX vendor
power domain tree which will retire later.
The Linux upstream use a single pd node for power domain driver,
and U-Boot will adopt that. When U-Boot i.MX8 dts synced with
Linux Kernel upstream and related driver ready, the legacy
driver will be removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
clk and pinctrl will be get(probed) during each device probe,
we don't need to probe them in scu driver. Only need to bind the sub-nodes
(clk and iomuxc) of MU node with their drivers.
So drop the code to probe the clk/pinctrl, and this patch will make it
easy to add more subnodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set gd->fb_base so it can be shown with bdinfo command.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now TI CPSW driver will disable MAC TX internal delay for PHY interface
mode "rgmii-rxid" which is incorrect.
Hence, fix it by keeping default value (enabled) for MAC TX internal delay
when "rgmii-rxid" interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds support for standard Ethernet "max-speed" DT property to
allow PHY link speed limitation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
[1] https://patchwork.kernel.org/patch/10285239/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can be called before the timer is set up. Make sure that the
init function is called so that it works correctly.
This is needed so that bootstage can work correctly in TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl25wUcACgkQxIHbvCwF
GsQ16w/+IibWYFw2t6AdI8DLWOvlHR/PVAOrbF9cBi1vZPr4drEH6m1ymRWAKjRt
E4u8siBiIs5yhD7laL09JK4p/veTnoHCVrCdli9iPhIJUFGKz9uuXh4ruZgRnGIn
+j0ra0tkTRHeGX4bMtTpMVySQqIuLQ+2ZrMMnfKfnTTlLmhv436xUyBZ/CFl7k4J
7sFj/FfjRCYpe7nfHTqUGidJtJG1cc+hw26c1YrfiKB6piVdH43myOB5sPDW24g3
OPptJyUFqbQjjV6Eq0EOVJt103rVtXpQc0e4Oa/mDDkmrQZ1pUhXi3zhxmzMRDQu
k+9gX0IoSNJcW+e7DrcQsx5SmOnlvoC4euCypzhWEWvES89ftAHIitEAz9oTs6Gc
etwXFomvH797ZOoBztrja9XsfnLFHBQHaAiExqEVVFi/1nhDsYdj+xEDHjDU+cZx
E3UcrRNXcfA2+oaXpNBguzAOrMPX8UbrR1kkaMDTuJfA32Pe7RLz3aMfXyx1rAOU
t7GWSROOYtoNf5IU/Jha1F8231WRPJnWm1LQdzNLaGSmbG/H7vFgW4dpdxEyLn4m
C0Goj0GzmBIQxRL+38sCOKLVxPEpGoU/GzonC9bU0O+UyN57rAiwn9ZbTa6ZvJqG
/2tPoKiutJRueUH3IDWViMhyW/w0h0tj0BUiV5lAQ9X9vW4E1YQ=
=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Bootstage improvements for TPL, SPL
Various sandbox and dm improvements and fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl24zDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZRiwf+Mf7oG//zjiZcHaPP6KOFb1CjwqLSuiaI
eCYB6GEZXuSpc8MjAw+baAfIw8MMFuaCfPsUQ5dDo391neK0sW9kkEsdcXnQBpB3
GdJYcewLN1UuJZovriGobIisGc0GQHh8gmRcVGWSKoEt+gAQauRtVYBIUPuS3JG+
ihZgYmVgICa+3tqavIbP2oZdXLuLAxR65mfiQHtiJwdCN3OOzyls2v0T0slQX9GV
ln6EvTk8OMIudBmkB7YiTmJF7AB+3PH/uBaiYyTKO9gtjLhnmCFvG5HxJTRFOKvU
F4oVWZJDEcqfZvYgWg8i5vgokMP41nzLfBr7j5ifUX1f3xwCHy/Tpw==
=S4XI
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29oct19' of git://git.denx.de/u-boot-dm
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Change the stack-allocated buffer for the identification command
to explicitly allocate page-aligned buffers. Even though the spec
seems to allow having admin queue commands on non page-aligned
buffers, it seems to not be possible on my i.MX8MQ board with a
a Silicon Power P34A80. Since all of the NVMe drivers I have seen
always do admin commands on a page-aligned buffer, which does work
on my system, it makes sense for us to do that as well.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It's possible that the data cache for the buffer still holds data
to be flushed to memory, since the buffer was probably used as stack
before. Thus we need to make sure to flush it also on reads, since
it's possible that the cache is automatically flused to memory after
the NVMe DMA transfer happened, thus overwriting the NVMe transfer's
data. Also add a missing dcache flush for the prp list.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Profiling the EHCI driver shows a significant performance problem in
ehci_submit_async(). Specifically, this function keeps enabling and
disabling async schedule back and forth for every single transaction.
However, enabling/disabling the async schedule does not take effect
immediatelly, but instead may take up to 1 mS (8 uFrames) to complete.
This impacts USB storage significantly, esp. since the recent reduction
of maximum transfer size to support more USB storage devices. This in
turn results in sharp increase in the number of ehci_submit_async()
calls. Since one USB storage BBB transfer does three such calls and
the maximum transfer size is 120 kiB, the overhead is 6 mS per 120 kiB,
which is unacceptable.
However, this overhead can be removed simply by keeping the async
schedule running. Specifically, the first transfer starts the async
schedule and then each and every subsequent transfer only adds a new
QH into that schedule, waits until the QH is completed and does NOT
disable the async schedule. The async schedule is stopped only by
shutting down the controller, which must happen before moving out
of U-Boot, otherwise the controller will corrupt memory.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Add weak callback to allow board specific behavior
- flush
- initiated
This patch prepare usage of DFU back end for communication with
STM32CubeProgrammer on stm32mp1 platform with stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a virtual DFU backend to allow board specific read and write
(for OTP update for example).
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the support of MTD partition for the MTD backend.
The expected dfu_alt_info for one alternate on the mtd device :
<name> part <part_id>
<name> partubi <part_id>
"partubi" also erase up to the end of the partition after write operation.
For example: dfu_alt_info = "spl part 1;u-boot part 2; UBI partubi 3"
U-Boot> dfu 0 mtd nand0
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DFU backend for MTD device: allow to read
and write on all MTD device (NAND, SPI-NOR,
SPI-NAND,...)
For example :
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd nand0
This MTD backend provides the same level than dfu nand
backend for NAND and dfu sf backend for SPI-NOR;
So it can replace booth of them but it also
add support of spi-nand.
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd spi-nand0
The backend code is based on the "mtd" command
introduced by commit 5db66b3aee ("cmd: mtd:
add 'mtd' command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch allows the DFU backend to indicate that that it can't
provide no more data to fill the DFU buffer, by setting b_left =0
without error, even if the size of received data is lower of the
expected total size indicated by get_medium_size.
For USB DFU stack point of view, it is acceptable:
the read length < requested size in DFU_UPLOAD and the
transaction is stopped.
That avoid infinite loop issue in dfu_read_buffer_fill because the
size for the DFU read is limited by get_medium_size = r_left
and the DFU stack expects that read is allowed up to this size.
This issue never occurs for current flash device (where chunk are
always completely read, and b_left will be never 0) but it is useful for
virtual partition when the backend only know the max size of this
alternate, the real size of the data are only known in the read
treatment.
PS: for file access on mmc, EOF is never reached as
dfu_get_medium_size_mmc returns the exact size of the file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Copy the partition support from NAND backend to SF,
support part and partubi option.
In case of ubi partition, erase the rest of the
partition as it is mandatory for UBI.
The added code is under compilation flag CONFIG_DFU_SF_PART
activated by default.
for example:
U-Boot> env set dfu_alt_info "spl part 0 1;\
u-boot part 0 2;u-boot-env part 0 3;UBI partubi 0 4"
U-Boot> dfu 0 sf 0:0:10000000:0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Calling cache flush on invalid buffer, even with zero length might cause
an exception on certain platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add possibility to define a part of partition as a separate DFU entity.
This allows to have more than one items on the given partition.
The real use case for this option is TM2 board. It can use u-boot stored
as Linux kernel on the defined partition (as RAW data) and load the real
kernel from the same partition, but stored under the certain offset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This is needed to make Windows THOR flash tool happy, because it
starts sending data only when interrupt packet is received on the 3rd
endpoint.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
In combination with multiple partitions in NAND, this printf() ends up
being more noise than helpful. Change it to debug() instead.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some boards don't populate clk/reset entries as these are are optional
as per binding documentation. Therefore, don't fail driver probe if
clk/reset entries are absent in DT.
This fixes fastboot failures seen due to enabling of CONFIG_CLK on AM57xx
Fixes: e8e683d33b ("board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
_gpio_direction_output function currently calls gpio_set_value
with the wrong gpio number. gpio_set_value in the uclass driver
expects a different gpio number and the _gpio_direction_output
is currently providing the number specific to the bank.
Hence fix it by calling the _gpio_set_value function instead.
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Fixes: 8e51c0f254 ("dm: gpio: Add DM compatibility to GPIO driver for Davinci")
Signed-off-by: Keerthy <j-keerthy@ti.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
The ext4 file system requires log2blksz to be set. So when setting the
block size on the block descriptor we should fill this field too.
This fixes a problem with EFI block devices providing ext4 partitions, cf.
https://lists.denx.de/pipermail/u-boot/2019-October/387702.html.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
0e1bf61 mmc: fsl_esdhc: Add support for DDR mode
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch.
66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Use log() insted of debug() for uclass_find_device_by_seq function,
since this print is very much and we can filter it out with log()
interface.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move #define to top of file as per docs:
Signed-off-by: Simon Glass <sjg@chromium.org>
This function assumes that the 'val' parameter has no masked bits set.
This is not defined by the function prototype though. Fix the function to
mask the value and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added training support for LPDDR4 and DDR3L DDRs. Also added/changed
some register configuration to support all 3 DDR types
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add an entry for the Adesto AT25SL321 SPI NOR chip.
This SPI NOR chip is found in the Embedded Artist i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.
Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).
We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.
We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Disable and free clock when remove driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.
This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25wp256, chip to spi-nor id table.
Tested on SiFive FU540 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
1) CONFIG_SPI_FLASH is not just a legacy code, but it has common
core code which handle both dm and non-dm spi flash code. So
fix the info text to make it clear globally.
2) Since it's flash core it shouldn't depends on legacy SPI,
so remove the 'depends on SPI'
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Example of USB nodes for iMX7S/D:
usbotg1: usb@30b10000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b10000 0x200>;
^^^^^^^^^^
....
usbotg2: usb@30b20000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b20000 0x200>;
^^^^^^^^^^
....
usbh: usb@30b30000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b30000 0x200>;
^^^^^^^^^^
....
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch adds manual relocation for Modular Exponentiation if
CONFIG_NEEDS_MANUAL_RELOC is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gpio driver for pmc gpio.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gpio driver for versal platform
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix error debug messages to be more accurate and aligned with debug message
style in the whole file.
And do not initialize ret variable because it is initialized later on and
it is just additional step.
Fixes: 1327d1678b ("firmware: zynqmp: Add zynqmp-power support")
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Function should report error when called in EL3 context. Also report it as
error instead 0 (success).
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
versal_pm_request() and invoke_smc() are almost the same. Only one
difference is that versal_pm_request is adding PM_SIP_SVC offset to api_id.
The patch is moving platform implementation to firmware driver code for
synchronization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
The Microchip Flexcom is just a wrapper which embeds a SPI controller,
an I2C controller and an USART.
Only one function can be used at a time and is chosen at boot time according
to the device tree.
The bindings are kept as in Linux.
The driver registers to MISC_UCLASS.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
There is no proper power domain support for the keystone platforms.
However we need to turn off the USB domains before jumping to linux or it
fail to boot (observed with k2e and k2l platforms).
This can be done in the PHY driver as it is dedicated only to the keystone
platforms and matches the required on/off sequence.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.
Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function that read quirk and configuration information from the
DT. The goal is to allow platforms using their own version of DWC3 driver
to migrate to the generic DWC3 driver.
The function is adapted from the function dwc3_get_properties() in the
linux dwc3 driver introduced in commit c5ac6116db35d.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no need to fail if the maximum speed is not specified.
If the speed is not specified, do the same as linux and assume super speed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Currently the host driver used by dwc3-generic is "xhci-dwc3". This is
a functional driver but it doesn't use the dwc3 core and, in particular,
it lacks some bits that may be important.
For example on the k2 platforms, it is important that the phy are properly
suspended when the USB is not used anymore. The dwc3 core also has a
partial support for quirks.
The new driver can be used as a drop-in replacement for "xhci-dwc3".
In terms of implementation, it may seem strange that 2 private structures
dwc3_generic_host_priv and dwc3_generic_priv) are used. The reason for this
is simply that the xhci layer expects a struct xhci_ctrl at the beginning
of the private data and it seemed wasteful to include it also for the
peripheral case.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No one is actually implementing those functions.
We could remove calls to these altogether, but it does not really hurt to
keep the empty inlined version at the moment and it satisfies a symmetry
with the gadget mode.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allow the phy to enter idle and then suspend.
the K2 platforms require the PHY to be suspended before the USB domain
clock can be turned off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Some SCSI devices like UFS use DMA for executing scsi commands and hence
need to know the direction of transfer of the dma. Add a dma_dir element
to the command structure to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The UFS SCSI device LUNs are observed to return failure the first time a
unit ready inquiry is sent and pass on the second try. Send this
inquiry 3 times to make sure device is ready.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add max_bytes_per_req to scsi_platdata to enable the host driver to limit
the number of bytes that can be read/written per request.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With no non-DM driver using scsi_read()/_write() APIs, remove
the legacy implementations.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[trini: Reorder slightly and mark scsi_read/write behind BLK test to
avoid warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
Make sure that the clock self-assignment works by having a clock of
clk-sbox be configured automatically when clk-sbox is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This fixes the case where assigned-clocks is used to define a clock
defaults inside this same clock's node. This is used sometimes to setup a
default parents and/or rate for a clock.
example:
muxed_clock: muxed_clock {
clocks = <&clk_provider 0>, <&clk_provider 1>;
#clock-cells = <0>;
assigned-clocks = <&muxed_clock>;
assigned-clock-parents = <&clk_provider 1>;
};
It doesn't work in u-boot because the assigned-clocks are setup *before*
the clock is probed. (clk_set_parent() will likely crash or fail if called
before the device probe function)
Making it work by handling "assigned-clocks" in 2 steps: first before the
clk device is probed, and then after the clk device is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a few more clocks the clk_sandbox clock provider and get them using
the managed API.
Make sure they are released when the device is removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add devm_clk_get(), devm_clk_get_optional() to get clocks from the
device-tree. The clocks is automatically released and the data structure
freed when the device is unbound.
Also add devm_clk_put() to release the clock and free the data structure
manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This change adds support for I2C clock modeled in CCF. This code intention
is to only enable those clocks in the I2C driver with default settings.
For that reason the "busy" versions of clocks reuse the generic approach
and would need to be updated when one wants to adjust the I2C clock
frequency in U-Boot.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the documentation in clk.h, clk_set_parent() return the new
rate of the clock or a negative error code.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit e878b53a79 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit c20851b3d8 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finally add the Amlogic G12A SoC compatible for the VPU driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Synchronize the Amlogic Meson Video driver back with the latest
DRM misc tree, adding G12A platform support, from the latest commit:
528a25d040bc ("drm: meson: use match data to detect vpu compatibility")
The sync includes the following changes from Linux adapted to U-Boot:
- Add support for VIC alternate timings
- Switch PLL to 5.94GHz base for 297Mhz pixel clock
- Add registers for G12A SoC
- Add G12A Support for VPP setup
- Add G12A Support for VIU setup
- Add G12A support for OSD1 Plane
- Add G12A support for plane handling in CRTC driver
- Add G12A support for CVBS Encoder
- Add G12A Video Clock setup
- Add G12A support for the DW-HDMI Glue
- fix G12A HDMI PLL settings for 4K60 1000/1001 variations
- fix primary plane disabling
- fix G12A primary plane disabling
- mask value when writing bits relaxed
- crtc: drv: vpp: viu: venc: use proper macros instead of magic constants
- global clean-up
- add macro used to enable HDMI PLL
- venc: set the correct macrovision max amplitude value
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Remove getting and enabling the node power domain since it's now handled
by the dm core directly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add necessary clock support to set up clock for the VPU and
HDMI support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add Amlogic G12A support for the gx-pwrc driver, aligned on the
Linux v5.2 driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
hs: fix typo in commit message
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
At present the 'Index' column of 'dm tree' assumes there is
two digits, this patch increase it to 3 digits.
It also aligns output of 'dm uclass', assuming the same 3 digits index.
The boards with CONFIG_PINCTRL_FULL activated have one pinconfig
by pin configuration, so they can have more than 100 devices
pinconfig (for example with stm32mp157c-ev1 board we have
106 pinconfig node).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixed CONFIG_IF_ENABLED() condition, added __maybe_unused:
Signed-off-by: Simon Glass <sjg@chromium.org>
The power domain associated with a device is enabled when probing,
but currently the domain remains enabled when the device is removed.
Some boards started to disable power domains for selected devices
via custom board_quiesce_devices(), but it doesn't work in many
cases, i. e. because devices still can be accessed later in
.remove() callback on behalf of dm_remove_devices_flags().
Utilize the DM core to power off the device power domain, but add a
device flag to be able to selectively let the power domain enabled
after device removal. This might be required for devices that must
remain enabled when booting OS, i. e. serial console for debug
output, etc.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add dev_power_domain_off() api to disable all the power-domains
corresponding to a device
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable DM_FLAG_DEFAULT_PD_CTRL_OFF for arm64 remote core so that
pd can be enabled after loading the image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In some remoteproc cases, enabling the power domain of the core will
start running the core. In such cases image should be loaded before
enabling the power domain. But the current DM framework enables the
power-domain by default during probe. This is causing the remotecore
to start and crash as there is no valid image loaded.
In order to avoid this introduce a DM flag that doesn't allow for
enabling/disabling the power-domain by DM framework.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip not associated gpio phandle let register the other gpios on a group.
We need anyway to send out a warning to the user to fix their uboot-board.dtsi.
Thhe handle id can be found inside the decompiled dtb
dtc -I dtb -O dts -o devicetree.dts spl/u-boot-spl.dtb
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When multiple power domains attached to a device, need power on
them all, so use dev_power_domain_on to do that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add this new API to power on multiple domains attached
to a device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Changed to static inline and added a condition into C file:
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_OF_PRIOR_STAGE is enabled, this workaround was needed
before device_bind_common assigned request numbers sequentially in the
absence of aliases.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
For CONFIG_OF_PRIOR_STAGE, in the absence of a device tree alias for a
given device, use the next request number for that type of device.
This allows aliases to be used when they're available, while still
allowing unaliased devices to be probed.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
The reset function sets the pin to 0 then 1 but if the pin is marked
ACTIVE_LOW in the DT it gets inverted and leaves the TPM in reset.
Let the gpio driver take care of the reset polarity.
Signed-off-by: Kayla Theil <kayla.theil@mixed-mode.de>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Add a Synopsys Designware MIPI DSI host bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Mipi_display.c contains a set of dsi helpers.
This file is a copy of file drm_mipi_dsi.c (linux kernel).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Regulator should not be enabled at probe time if regulator-boot-on
property is not in the dt node.
"enable-active-high" property is only used to indicate the GPIO
polarity.
See kernel documentation :
- Documentation/devicetree/bindings/regulator/fixed-regulator.yaml
- Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In 32bits mode upper bits need to be set to 0, otherwise controller will
try to DMA into not existing memory and stops with error.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Oleksandr Rybalko <ray@ddteam.net>
The driver provides PHY for USB2, USB3.0, PCIe and SATA, and now
we just enable PCIe. As for the other functionalities will be
added gradually in upcoming days.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds PCIe controller support for MT7623.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
The Broadcom ARM implementations do not yet have a clock framework so
one can use a fixed clock as the root clock of the hsspi block. The
fixed clock does not have an "enable" routine, since it's always
enabled. So when we hit this issue, getting an ENOSYS return, do not
bail but continue initialization.
Similarly the block might already have been out of reset, say, when
we are booting from a SPI device. So if the reset signal is not configured
in the device tree, do not bail out and instead skip deasserting the reset.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Make the driver compatible with both big and little endian SOCs.
Replace big-endian calls with their raw equivalents, expect for
writing the command to FIFO. That still has to be in big-endian
format.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This IP exists in both MIPS and ARM cores, so we also
allow to use this driver on bcm6858 and bcm63158.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Certain SoCs with K3 architecture have integrated a C66 Corepac DSP
subsystem and an advanced C71 DSPs. Introduce a remoteproc driver
that that does take care of loading an elf to any of the specified
DSPs and start it.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
SoCs with K3 architecture have an integrated Arm Cortex-R5F subsystem
that is comprised of dual-core Arm Cortex-R5F processor cores. This R5
subsytem can be configured at boot time to be either run in a LockStep
mode or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has each Tightly-Coupled Memory (TCM) internal memories
for each core split between two banks - TCMA and TCMB.
Add a remoteproc driver to support this subsystem to be able to load
and boot the R5 cores primarily in LockStep mode or split mode.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Power domain for the remote cores needs to be handled in a right
sequence as mandated by the spec. Introduce tisci helper apis
that can control power-domains of remote cores. TISCI clients
can use this api and control the remote cores power domain instead
of hooking it to power-domain layer.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce rproc_elf_get_boot_addr() that returns the entry point of
the elf file. This api auto detects the 64/32 bit elf file and returns
the boot addr accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce a common remoteproc elf loader and checker functions that
automatically detects the 64 bit elf file or 32 bit elf file and
loads/checks the sections accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
The current rproc-elf-loader supports loading of only 32 bit elf files.
Introduce support for loading of 64 bit elf files in rproc-elf-loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
rproc_elf32_load_image() rely on user to send a valid address for elf loading.
Instead do a sanity check on the address passed by user. This will help
all rproc elf users to not call sanity_check explicitly before calling
elf_loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Introduce a new parameter "size" that accepts size of the region to
remoteproc ops callback device_to_virt(). This can enforce more checks
on the region that device_to_virt() is dealing with.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
