After settings the speed of the sd with the switch command, a check is
done to make sure that the new speed has been set. The current check has a
masking error: speed are encoded on 4 bits only.
Fix it by masking the upper bits.
This fixes a problem seen with QEmu emulating a vexpress-a15.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc core has defined a new parameter *clk_disable* to gate the clock.
Disable the clock here if *clk_disable* is set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).
Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use pr_* log functions from Linux. They can be enabled/disabled
via CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Fixes: 9546eb92cb ("mmc: fix the wrong disabling clock")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76a ("mmc: disable the mmc clock during power off")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
During the tuning, drivers repeat data transfer, changing timing
parameters in the controller hardware. So, the tuning commands
(CMD19 for SD, CMD21 for eMMC) fail, and this is not a problem
at all.
Showing "Error detected..." in normal operation just make users
upset. This should not be shown.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This line overwrites host_cap that has been set by drivers and/or
helpers like mmc_of_parse(). Accumulate capabilities flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You must fix your DT if it specifies insane bus-width, for example,
bus-width = <3>;
debug() is not displayed in usual configuration, so people will not
even notice weirdness. Use dev_err() instead, then let it fail.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc_of_parse() in U-Boot is a pussy helper; it sets cfg->f_max to
52MHz even if DT does not provide "max-frequency" at all. This can
overwrite cfg->f_max that may have been set to a reasonable default.
As the DT binding says, "max-frequency" is an optional property.
Do nothing if DT does not specify it. This is the behavior of
mmc_of_parse() in Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.
Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
struct mmc_data contains the block size to use for the data transfer.
Use this information instead of using the default value or the block length
information stored in struct mmc.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The SDcard initialization procedure does a few more things than it did earlier:
* switch the bus width even for 1-bit bus width
* check that speed has been properly set (in resp[4] of SD_CMD_SWITCH_FUNC)
Update the SD simulator to handle those requests gracefully.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Not using this function reduces the size of the binary. It's replaces by
a standard malloc() and the alignment requirement is handled by an
intermediate buffer on the stack.
Also make sure that the allocated buffer is freed in case of error.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The ext_csd is allocated only for MMC above version 4. The compare will
crash or fail for older MMCs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Make sure that those basic capabilities are advertised by the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the legacy modes were not added to the list of supported modes, old
cards that do not support other modes could not be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* convert to livetree API
* don't fail because of an invalid bus-width, instead default to 1-bit.
* recognize 1.2v DDR and 1.2v HS200 flags
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is a useful information while debugging the initialization process or
performance issues.
Also dump this information with the other mmc info if the verbose option
is selected
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function to parse host controller dt node and
set mmc_config. This function can be used by mmc controller
drivers to set the generic mmc_config.
This function can be extended to set other UHS mode caps
once UHS mode support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card.
Add a simple function to send tuning command and to read and
compare the received data with the tuning block pattern.
This function can be used by platform driver to perform DLL
tuning.
This patch is similar to
commit 996903de92f0 ("mmc: core: add core-level function for
sending tuning commands") added in linux kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v
or 1.2v signal voltages.
Select the lowest voltage available when using those modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.
To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Boot partitions do not support HS200. Changing to a lower performance mode
is required to access them.
mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to
make it easier to call them outside of the initialization context.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a power cycle cannot be done on Vcc, it is safer not to try the UHS
modes because we wouldn't be able to recover from an error occurring
during the UHS initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add UHS modes to the list of supported modes, get the UHS capabilites of
the SDcard and implement the procedure to switch the voltage (UHS modes
use 1v8 IO lines)
During the voltage switch procedure, DAT0 is used by the card to signal
when it's ready. The optional card_busy() callback can be used to get this
information from the host driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add HS200 to the list of supported modes and introduce tuning in the MMC
startup process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes.
This callback execute the tuning process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no point in having the mmc clock enabled during
power off. Disable the mmc clock. This is similar to how it's
programmed in Linux Kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc/sd specification requires vdd to be disabled for 1 ms
and then enabled again during power cycle. Add a
function in mmc core to perform power cycle and set
the io signal to it's initial state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new callback function *send_init_stream* which start a sequence of
at least 74 clock cycles.
The mmc core uses *mmc_send_init_stream* in order to invoke the callback
function. This will be used during power cycle where the specification
requires such a sequence after power up.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function *mmc_set_signal_voltage* in mmc core
which can be used during mmc initialization to select the
signal voltage. Platform driver should use the set_ios
callback function to select the signal voltage.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
set_ios callback has a return value of 'int' but the mmc_set_ios()
function ignore this. Modify mmc_set_ios() and the callers of mmc_set_ios() to
to return the error status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MMC startup process currently handles 4 modes. To make it easier to
add support for more modes, let's make the process more generic and use a
list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SDcard startup process currently handles only 2 modes. To make it
easier to add support for more modes, let's make the process more generic
and use a list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple helper function to display information (bus width and
mode) based on a capability mask. Useful for debug.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
no functionnal changes.
In order to add the support for the high speed SD and MMC modes, it is
useful to track this information.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will be reused later in the selection of high speed and ddr modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ext csd is used for comparison many times. Keep a reference content
of the ext csd in the struct mmc to avoid reading multiple times
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
no functionnal change. This is only to further reduce the size o
mmc_startup().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
No functionnal change here. The function is really big and can be split.
The part related to bus configuration are put in 2 separate functions: one
for MMC and one for SD.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get a reference to the regulator devices from the dts and store them
in the struct mmc for later use.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
data is defined as struct mmc_data *data.
So it should not be compared to 0.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes emmc initialization regression on the db410c platform.
Clearing this register while SDHCI_PRESENT_STATE reports
SDHCI_CMD_INHIBIT leads to undefined behaviour on the db410c.
When commit 7dde50 was merged (mmc: sdhci: Wait for SDHCI_INT_DATA_END
when transferring), SDHCI transfers transitioned to wait for bit
SDHCI_INT_DATA_END before flagging transfers done.
Without this patch, the db410 platform fails to initialize its eMMC
due to all of its transfers timing out (SDHCI_INT_DATA_END is never
raised after all the blocks have been transferred).
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This patch fixes some warnings when building boards that do not define
DM_I2C_COMPAT i.e. boards that entirely rely on the new i2c layer.
Signed-off-by: Felix Brack <fb@ltec.ch>
priv pointer should be freed before returning with an error value
from exynos_dwmci_get_config().
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Raghu Bharadwaj <raghu@techveda.org>
__be32_to_cpu() accepts argument of type __be32. This patch changes
type of the buffer in ALLOC_CACHE_ALIGN_BUFFER macro to __be32, which
is then passed to __be32_to_cpu().
This prevents sparse build warnings.
drivers/mmc/mmc.c: warning: cast to restricted __be32
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Add new compatible to the Uniphier SD driver for R8A77995 D3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the Uniphier SD driver for R8A77970 V3M SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MMC commands like MMC_CMD_ALL_SEND_CID or MMC_CMD_SEND_CSD can reach
500 us. This patch increases the polling status register delay to avoid
a timeout on a command.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since e7881d85 "dm: mmc: Drop CONFIG_DM_MMC_OPS" DM_MMC_OPS
is no more used, remove it from STM32_SDMMC2 dependencies
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC framework in U-Boot does not support a systematic API for
timing switch like mmc_set_timing() in Linux.
U-Boot just provides a hook to change the clock frequency via
mmc_set_clock(). It is up to drivers if additional register
settings are needed.
This driver needs to set a correct timing mode into a register when
it migrates to a different speed mode. Only increasing clock frequency
could result in setup/hold timing violation.
The timing mode should be decided by checking MMC_TIMING_* like
drivers/mmc/host/sdhci-cadence.c in Linux, but "timing" is not
supported by U-Boot for now. Just use mmc->clock to decide the
timing mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial support for setting the vqmmc regulator. Since we do not
support 1V8 modes, set the regulator to 3V3 and enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Old version of the uniphier-sd 64bit IO support patchset V1 was
applied by the maintainer, update the uniphier-sd.c with the
changes from the V3 of the patchset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds SD/MMC support for STM32H7 SoCs.
Here is an extraction of SDMMC main features, embedded in
STM32H7 SoCs.
The SD/MMC block include the following:
_ Full compliance with MultiMediaCard System Specification
Version 4.51. Card support for three different databus modes:
1-bit (default), 4-bit and 8-bit.
_ Full compatibility with previous versions of MultiMediaCards
(backward compatibility).
_ Full compliance with SD memory card specifications version 4.1.
(SDR104 SDMMC_CK speed limited to maximum allowed IO speed,
SPI mode and UHS-II mode not supported).
_ Full compliance with SDIO card specification version 4.0.
Card support for two different databus modes: 1-bit (default)
and 4-bit. (SDR104 SDMMC_CK speed limited to maximum allowed IO
speed, SPI mode and UHS-II mode not supported).
_ Data transfer up to 208 Mbyte/s for the 8 bit mode.
(depending maximum allowed IO speed).
_ Data and command output enable signals to control external
bidirectional drivers.
The current version of the SDMMC supports only one SD/SDIO/MMC card
at any one time and a stack of MMC Version 4.51 or previous.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add OF match entries and quirks for Renesas RCar Gen3 controllers
into the driver. The IP this driver handles is in fact Matsushita
one and in used both in Socionext and Renesas chips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Check if the OF match has any associated data and if so, use those
data as the controller quirks, otherwise fallback to the old method
of reading the controller version register to figure out the quirks.
This allows us to supply controller quirks on controllers which ie.
do not have version register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita. This patch adds support for handling of the 64bit
FIFO on this controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita, yet the register addresses are shifted by 1 to the
left. The whole controller is also 64bit, including the data
FIFOs and RSP registers. This patch adds support for handling
the register IO by shifting the register offset by 1 in the IO
accessor functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
This patch prepares the driver to support controller(s) with registers
at locations shifted by constant. Pull out the readl()/writel() from
the driver into separate functions, where the adjustment of the register
offset can be easily contained.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Use struct udevice* as input parameter. Previous
parameters are retrieved through plat and priv data.
This to prepare to use the reset framework.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_sdhci.c
Update the Rockchip-specific wrapper for the Designware driver to
support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_dw_mmc.c
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When enabling the new mmc timing mode, we inadvertently clear all the
remaining bits in the new timing mode register. The bits cleared
include a default phase delay on the output clock. The BSP kernel
states that the default values are supposed to be used. Clearing them
results in decreased performance or transfer errors on some boards.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The driver-model rework changed, among other things, the way the private
data were moved around. It now uses the private field in the struct mmc.
However, the mmc_create argument was changed in the process to always pass
the array we used to have to store our private structures.
The basically means that all the MMC driver instances will now have the
private data of the first instance, which obviously doesn't work very well.
Pass the proper pointer to mmc_create.
Fixes: 034e226bc7 ("dm: mmc: sunxi: Pass private data around explicitly")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.
Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.
Add support for it through a Kconfig option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This changes pci_mmc driver to use PCI_CLASS_SYSTEM_SDHCI instead of
individual vendor id & device id pair to support generic PCI SD host
controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This patch allows to show the EXT_CSD[179] partition_config
register info, just by specifying the dev param:
U-Boot> mmc partconf 0
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x0
BOOT_PARTITION_ENABLE: 0x0
PARTITION_ACCESS: 0x0
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we will not use mmc->priv to access driver-private data.
To accomodate this, update internal functions so that we can pass the
private data directly. This will allow the caller to obtain it as it
prefers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bind() method is called before the device is probed and so the
device has no private data, should use the platform data, and set up
a new struct to hold the mmc and cfg members.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we now have clock driver for the RCar Gen3 , add support for
enabling the clock into the SH SDHI driver to prevent hacks in the
board files.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The command handling in this driver is awful, esp. because the driver
depends on command numbers to determine whether this is APPCMD or not.
Also, handling of command RSP response types is totally wrong.
This patch at least plucks out some of the custom command encoding and
fixes the APPCMD handling. The RSP handling still needs work, yet that
might not be needed as it turns out the uniphier-sd.c driver is in much
better shape and supports the same IP, so we might be able to just drop
this driver in favor of the uniphier one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add MMC DM and DT probing support into the SH SDHI driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The long response entry 0..3 LSByte comes from the next response
register MSByte, not from the next response register LSByte. Fix
this to make the driver report correct values in response 136 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We shouldn't always change the status to okay. There could be
situations that the esdhc is intentionally disabled in the device
tree.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit 4483b7eb added variable vqmmc_dev but only uses it under
CONFIG_DM_REGULATOR. Add the same macro to variable declaration to
get rid of compiling warning.
Signed-off-by: York Sun <york.sun@nxp.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver-model version of this driver which mostly uses the existing
code. The old code can be removed once all boards are switched over.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has #ifdefs in it which we want to avoid for driver model.
Instead we should use different compatible strings and the .data field.
It also uses the MMC device number which is not available in driver
model except through aliases.
Move the function's into its caller so that the driver-model version can
do things its own way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present the driver-private data is obtained in various functions by
various means. With driver model this is provided automatically. Without
driver model it comes from a C array declared at the top of the file.
Adjust internal functions so that they are passed the private data as
a parameter, allowing the caller to obtain it using either means.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use the driver-model naming convention for this structure. It is data
private to the driver so the local variable should be called 'priv'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use the driver-model naming convention for this structure. It is data
private to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if U-Boot proper uses driver model for MMC, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
Add new SPL versions of the options for DM_MMC, DM_MMC_OPS and BLK. By
default these follow their non-SPL versions, but this can be changed by
boards which need it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the tegra mmc driver to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
DTB is encoded in big endian. When we retrieve property values,
we need to use fdt32_to_cpu (aka be32_to_cpu) for endian conversion.
This is a bit error-prone, but sparse is useful to detect endian
mismatch.
We need to use (fdt32_t *) instead of (u32 *) for a pointer of a
property value. Otherwise sparse warns "cast to restricted __be32".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
According to MMC spec, the write_counter is 4-byte length,
use 'int' instead of 'long' type for the 'long' is not 4-byte
in 64 bit CPU.
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Handle vqmmc supply. Some boards have a fixed I/O voltage
at 1.8V for emmc, so the usdhc also needs to be configured
as 1.8V by setting VSELECT bit. The vs18_enable is the one
that used to checking whether setting VSELECT or not in
the driver. So if vqmmc supply is 1.8V, set vs18_enable,
the driver will set VSELECT.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.
This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.
We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The origin patch get rockchip dwmmc by name 'ciu', which lead
to the SPL not able to remove 'clock-names' node in dts.
I'm not saying this is not correct, but I would prefer to handle
this in dts or clock driver to save memory for SPL.
For example the rk3288 SPL size has out of memory if not enable
BACK_TO_BROM option, there are many other SoCs has less internal
memory than rk3288.
This reverts commit 480a9b834c.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency for
all rockchip SoC dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the dw_mmc and sdhci wrapper drivers for Rockchip.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is used in another board; remove board information from
the driver debug log.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver currently does not reset bit 5 of the hostctl register even if
the MMC stack requests it. Then means that once a bus width of 8 is
selected it is not possible to change it back to 1. This breaks
'mmc rescan' which needs to start off with a bus width of 1.
The problem was surfaced by enabling CONFIG_DM_MMC_OPS on tegra. Without
this option the MMC stack fully reinits the driver on a 'mmc rescan'.
But with this option driver model does not re-probe a driver once it has
been probed once.
Fix the driver to honour the request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Chubb <peter.chubb@data61.csiro.au>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We do not need to probe the block device here, so avoid doing so. The MMC
device itself must be active, but the block device can come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is called when the MMC block device is being probed. There
is a recursive call in this function since find_mmc_device() itself can
cause the MMC device to be probed.
Admittedly the MMC device should already be probed, since we would not be
probing its child otherwise, but the current code is unnecessarily
convoluted.
Rewrite this to access the MMC structure directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
When binding a new MMC device, make sure that it has the required
operations. Since for now we still support *not* having the operations
(with CONFIG_DM_MMC_OPS not enabled) it makes sense to add this check.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not call out to board code from drivers. With driver model,
mmc_power_init() already has code to use a named regulator, but the
legacy code path remains. Update the code to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
Don't build non DM_MMC code when DM_MMC defined so move
them into #ifndef CONFIG_DM_MMC
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
On i.MX, SYSCTL.SDCLKFS may be set to 0 in order to make the SD clock
frequency prescaler divide by 1 in SDR mode. In DDR mode, the prescaler
can divide by up to 512. Allow both of these settings.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Number of blocks is a 9 bit field where 0 stands for a unlimited
number of blocks. Therefore the max number of blocks which can
be set is 511.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
To fix the timeout of sending the write command, enable the quirk
SDHCI_QUIRK_WAIT_SEND_CMD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simplifies makefiles. Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is a counterpart of drivers/mmc/host/sdhci-cadence.c
from Linux. Some updates for v4.12-rc1 can be imported to U-Boot.
- Fix value of SDHCI_CDNS_HRS04_RDATA_SHIFT
- Add polling for ACK bit to be sure that data are written to
the PHY register
- Retrieve PHY values from DT properties instead of fixed data
The following is the list of upstream commits:
- Linux commit 4e03f628b464e0580abadf5161eaa38c61d20943
mmc: sdhci-cadence: fix bit shift of read data from PHY port
- Linux commit a0f8243229ed071c8da0ea7cedc1b7bf1b1515da
mmc: sdhci-cadence: Fix writing PHY delay
- Linux commit a89c472d8b55c5afc4c79e6e3d1338730034eb01
mmc: sdhci-cadence: Update PHY delay configuration
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the programmable clock mode, the SDCLK frequency is incorrectly
assigned when the maximum clock has been assigned during probe,
this causes the SDHCI not work well.
In the programmable clock mode, when calculating the SDCLK Frequency
Select, when the maximum clock has been assigned, it is the actual
value, should not be multiplied by host->clk_mul. Otherwise, the
maximum clock is multiplied host->clk_mul by the base clock achieved
from the BASECLKF field of the Capabilities 0 Register.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For platforms that don't use device tree in SPL the only
way to mark this driver as 'required by relocation' is
with the DM_FLAG_PRE_RELOC flag. Add this to ensure that
the driver is bound.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The 'clock-freq-min-max' property was deprecated in the upstream
(i.e. Linux) DTS bindings in favor of the 'max-frequency' property.
With the latest RK3399 DTSI does no longer include the deprecated
property and the rockchip_dw_mmc driver requiring it to be present,
the driver doesn't bind to the node in the RK3399 DTSI any longer
(thus breaking access to the SD card on the RK3399-Q7 board).
To fix this, we implement a similar logic as in the Linux driver: if
the deprecated property is present, we issue a warning (if DEBUG is
enabled); if it is missing, we require 'max-frequency' to be set and
use it to create a min/max value-pair.
See b023030f10
for the deprecation/matching change in Linux.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As you know, biu_clk is used for AMBA AHB/APB interface, ciu_clk is
used for communication between host and card devices. The real bus clock
is ciu, so let's rectify it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the
.compatible flags.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the bcm2835 SDHCI driver over to support CONFIG_DM_MMC and move
all boards over. There is no need to keep the old code since there are no
other users.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The maximum supported peripheral clock frequency of the zynq depends on
the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz
respectively 25 MHz. Use the max-frequency value of the device tree to
determine the maximal supported peripheral clock frequency.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base
clock frequency but this clock is not fixed and depends on the hardware
configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ
doesn't match the real base clock frequency of SDIO_FREQ. Use the clock
framework to determine the frequency at run time.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It was incorrect to always include "asm/arch-omap3/mux.h" constantly.
This introduced warnings on non-omap3 where certain values will conflict
between the various families. Conditionally guard the inclusion in
order to correct the problem.
Fixes: 6aca17c9b7 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx")
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC devices accessed exclusively via the driver model were not
being initialized before being exposed as block devices, causing
issues in scenarios where the MMC device is first accessed via the
uclass block interface.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has
a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which
are related to GPIO_126, 127 and 129 are disabled. Some boards may
need this for MMC. After the PBIAS is configured, this bit should
be set high to enable these GPIO pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ftsdc021_sdhci.c is dead file.
There is no reason to maintain this host controller.
Removes the entire ftsdc021_sdhci.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If there are alias nodes as "mmc", use the devnum as alias index
number.
This patch is for fixing a problem of Exynos4 series.
Problem is the below thing.
Current legacy mode:
EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1
After using DM:
SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1
Dev index is swapped.
Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev.
If change from legacy to DM, also needs to touch all exynos4 config file.
For using simply, just supporting the fixed devnum with alias node is better than it.
Usage:
alaise {
....
mmc0 = &sdhci2; /* eMMC */
mmc1 = &sdhci1; /* SD */
...
}
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ROCKCHIP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[1] Rename CONFIG_SANDBOX_MMC to CONFIG_MMC_SANDBOX for consistency
I want all MMC driver options prefixed with CONFIG_MMC_.
[2] Fix dependency
Add necessary depends on to avoid compile error.
Instead "depends on MMC" is unneeded because this config entry
resides inside of "if MMC".
[3] Currently, this config symbol is not referenced at all.
Use it to enable/disable the driver in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
