In the video drivers it is useful to print errors while debugging but
doing so risks an infinite loop as the debugging info itself may go
through the video drivers.
Add a new console function that prints information only to the serial
device, thus making it safe for use in debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Similar to dm_rtc_read(), introduce a helper that allows the caller to
write multiple consecutive 8-bit registers with one call. If the
driver provides the ->write method, use that, otherwise loop using
->write8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some users may want to read multiple consecutive 8-bit
registers. Instead of each caller having to implement the loop,
provide a dm_rtc_read() helper. Also, allow a driver to provide a
->read method, which can be more efficient than reading one register
at a time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
rsa_verify() expects a memory region and wants to do the hashing itself,
but there may be cases where the hashing is done via other means,
like hashing a squashfs rootfs.
So add rsa_verify_hash() to allow verifiying a signature against
an existing hash. As this entails the same verification routines
we can just move the relevant code over from rsa_verify() and also
call rsa_verify_hash() from there.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Define this macro always so we don't need the preprocessor to check it.
Convert the users to #if instead of #ifdef.
Note that '#if MEM_SUPPORT_64BIT_DATA' does not give an error if the
macro is not define. It just assumes zero.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add linefeeds before and after the announce string. This makes the
output easier to read, especially if some text follows the announce
message without a specific additional CR.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The arch timer on 64-bit Arm Ltd. platforms is driven by a 24 MHz
crystal oscillator, so the frequency is not 25165824 MHz, as the current
code suggests.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Now that, we calculate SDRAM size by reading DDR registers,
"CONFIG_SYS_SDRAM_SIZE" is no more needed.
This commit removes "CONFIG_SYS_SDRAM_SIZE" from common configuration
file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch adds support for ZSTD decompression of FIT images.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added command "fstypes" to list supported/included filesystems.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Limit to sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the boot command used in ST boards, bootcmd_stm32mp, only support
the SD card as second stage, where is found the bootfs with DISTRO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The built in keyboard on the Pinebook Pro is attached via USB so
fix this up to ensure USB works as expected.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
-----BEGIN PGP SIGNATURE-----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=wwI2
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for UEFI sub-system for efi-2020-10-rc1
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
- Resync Kconfiglib with the v14.1.0 release.
- Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream.
- Fully resync checkpatch.pl with v5.7 release.
To safely to all of the above, we have a few bugfixes about functions
that need a 'static inline' but weren't. We also stop setting
CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes
boards can now opt-in to optimizing inlining and we do this for the
socfpga stratix10 platform for space savings.
Export the UEFI sub-system initialization state. This will allow to treat
the setting of UEFI variables during and after initialization differently.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There are cases where when we allow the compiler to decide about making
inline decisions rather than forcing them it can save us space.
For now, we keep the default values for inlining that we have had
historically.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the Linux kernel, support for forcing inline functions to be made
inline, rather than allowing the compiler to make its own choice has
been removed. With respect to performance, modern GCC (and Clang) do a
good job at deciding when to, or not to, inline code and there are no
run-time requirements in Linux anymore.
There is one downside to this, which is final binary size. On average
in U-Boot removing this support grows SPL by almost 1 kilobyte. But
there are cases where it shrinks the binary by making better inline
choices than we had forced.
Start by re-introducing CONFIG_OPTIMIZE_INLINING as a global which
essentially reverts 889b3c1245de ("compiler: remove CONFIG_OPTIMIZE_INLINING entirely")
from Linux.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Copy these from Linux v5.7-rc5 tag.
This brings in some handy new attributes and is otherwise important to
keep in sync.
We drop the reference to smp_read_barrier_depends() as it is not
relevant on the architectures we support at this time, based on where
it's implemented in Linux today. We drop the call to kasan_check_read()
as that is not relevant to U-Boot as well.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Where possible, I have tried to find compatible drivers based on the layout
of registers. However, many devices remain untested. All untested devices
have been left disabled, but some tentative properties (such as compatible
strings, and clocks, interrupts, and resets properties) have been added.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
dev_read_addr_ptr had different semantics depending on whether OF_LIVE was
enabled. This patch converts both implementations to return NULL on error,
and converts all call sites which check for FDT_ADDR_T_NONE to check for
NULL instead. This patch also removes the call to map_physmem, since we
have dev_remap_addr* for those semantics.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to the large number of clocks, I decided to use the CCF. The overall
structure is modeled after the imx code. Clocks parameters are stored in
several arrays, and are then instantiated at run-time. There are some
translation macros (FOOIFY()) which allow for more dense packing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
This is a small driver to do a software bypass of a clock if hardware
bypass is not working. I have tried to write this in a generic fashion, so
that it could be potentially broken out of the kendryte code at some future
date. For the K210, it is used to have aclk bypass pll0 and use in0 instead
so that the CPU keeps on working.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
This pll code is primarily based on the code from the kendryte standalone
sdk in lib/drivers/sysctl.c. k210_pll_calc_config is roughly analogous to
the algorithm used to set the pll frequency, but it has been completely
rewritten to be fixed-point based.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Clean-up platform data include file by using BIT macro and converting
indentation with spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the CONFIG_DM_SPI_FLASH and CONFIG_SPI_FLASH_DATAFLASH
to be defined in Kconfig, not in board specific header file
(include/configs/<board>.h).
Before this change the CONFIG_DM_SPI_FLASH was not set in .config (so it
was not possible to use CONFIG_IS_ENABLED(DM_SPI_FLASH) in SPI DM/DTS
converted drivers), but it was set in u-boot.cfg file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch fixes issue with defining the DM_SPI_FLASH in the
configs/include/<board.h> instead of enabling this option in Kconfig.
The problem is that CONFIG_IS_ENABLED(DM_SPI_FLASH) shows false as there
is no DM_SPI_FLASH=y in .config (but the define is set in u-boot.cfg).
As a result conversion of DM_SPI_FLASH to using CONFIG_IS_ENABLED() is not
working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fix banner string overwriting the logo on small displays
- fix splash warning when building for ARM64
- fix STM32 DSI driver to probe only on supported hardware
- fix memory corruption with DSI panel drivers
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXviLYw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDKoAJ9c+Rcel2q/lM8lK4NkhVLIdOfFxgCffcy4laCM
A1Hk+Ru0PQ77dhlI684=
=g+Hg
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix logo on mx6ul_14x14_evk with DM_VIDEO enabled
- fix banner string overwriting the logo on small displays
- fix splash warning when building for ARM64
- fix STM32 DSI driver to probe only on supported hardware
- fix memory corruption with DSI panel drivers
Add new fields "lanes, format & mode_flags" to structure
mipi_dsi_panel_plat.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are two remaining users of the CONFIG_SECURE_BOOT symbol that have
not been migrated to another symbol. In this case, they should be using
CONFIG_NXP_ESBC as their guard.
Cc: Vladimir Oltean <olteanv@gmail.com>
Fixes: 5536c3c9d0 ("freescale/layerscape: Rename the config CONFIG_SECURE_BOOT name")
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_MUX
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
CONFIG_BOOTCOUNT_LIMIT
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_STOP_STR
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_NAND_HW_PMECC
CONFIG_ATMEL_NAND_HWECC
CONFIG_NAND_ATMEL
CONFIG_PMECC_CAP
CONFIG_PMECC_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
We don't really want to have ARM-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the functions to print a number and a frequency are static. We
want to move some of the code in here to an arch-specific file. For
consistency that code should use these same functions. So export them with
an appropriate name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These values were 'old' in 2013 so it should be safe to remove them. They
are never set in U-Boot anyway, so the values will always be zero.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Reduce console buffer size to 1kbyte to accommodate memory
allocations in mini u-boot for zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Correct the PL bitstream loading sequence for zynqaes command by
clearing the loaded PL bitstream before loading the new encrypted
bitstream using the zynq aes command. This was done by setting
the PROG_B same as in case of fpgaload commands.
This patch fixes the issue of loading the encrypted PL bitstream
onto the PL in which a bitstream has already been loaded
successfully.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: fa33d20749 ("mmc: split fsl_esdhc driver for i.MX")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Commit 0528979fa7 ("part: Drop disk_partition_t typedef") changed to
a struct. As a result it uncovered an apparent missing include in
zfs_common.h for part.h which actually contains the definition. The ZFS
handles the struct exclusively as pointers so it was only a warning.
warning: ‘struct disk_partition’ declared inside parameter list
will not be visible outside of this definition or declaration
void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info);
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Series-CC: Simon Glass <sjg@chromium.org>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The distro bootscript uses kernel_image to get the file name of
the kernel, so change that variable name.
UBI boot has precedence in the default boot command. If one wants
to boot from SD with a working NAND installation stop in U-Boot
and enter:
setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
When using distro boot to boot from UBI volumes the boot partition
has been hardcoded to "UBI" (capital letters). However, our default
MTD layout uses "ubi" (lower case letter). Define "ubi" as the
default UBI partition for distro boot for Toradex. This allows to
use distro boot without having to redefine the MTD partition layout
which is useful for TorizonCore.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.
This also brings the benefit of restoring Ethernet functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
DXNTYVrHS/43T8ijGYo=
=7G75
-----END PGP SIGNATURE-----
Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
The ethernet PHY on all known Gen3 boards takes a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Migration to DM_VIDEO driver is long overdue, configure it in
board config files. To enable the display set stdout like:
setenv stdout serial,vidconsole
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
-----BEGIN PGP SIGNATURE-----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=yON/
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc5
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
The random_port() routine is not used anywhere else. Make it local to
dns.c to reduce code clutter, and shrink generated code a little.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add phy_set/clear_bit helper routines so that ported drivers from the
kernel can use these functions.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Fix kernel doc warnings in phy.h. Mostly the warnings were due to the
return missing the semi-colon.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add kernel doc to the phy_read/write utility functions in phy.h
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This keeps the compatibility with the old bootcmd.
The fdtfile environment variable also needed to be set to
imx6q-tbs2910.dtb to enable booting mainline kernels
otherwise with extlinux.conf it tries to load
mx6-tbs2910.dtb instead.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +2041 bytes
- data: 0 bytes
- bss: 0 bytes
- total: +2041 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This doesn't affect the size of the image: with
arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux
distribution, the text, data, bss and total sizes remain
unchanged.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
The current recommendation for best security practice from the US government
is to use SHA384 for TOP SECRET [1].
This patch adds support for SHA384 and SHA512 in the hash command, and also
allows FIT images to be hashed with these algorithms, and signed with
sha384,rsaXXXX and sha512,rsaXXXX
The SHA implementation is adapted from the linux kernel implementation.
[1] Commercial National Security Algorithm Suite
http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
If there are aliases for an uclass, set the base for the "dynamically"
allocated numbers next to the highest alias.
Please note, that this might lead to holes in the sequences, depending
on the device tree. For example if there is only an alias "ethernet1",
the next device seq number would be 2.
In particular this fixes a problem with boards which are using ethernet
aliases but also might have network add-in cards like the E1000. If the
board is started with the add-in card and depending on the order of the
drivers, the E1000 might occupy the first ethernet device and mess up
all the hardware addresses, because the devices are now shifted by one.
Also adapt the test cases to the new handling and add test cases
checking the holes in the seq numbers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> [on zcu102-revA]
If CONFIG_DM_DEV_READ_INLINE is set, dev_read_alias_highest_id() calls
libfdt_get_highest_id(). But this function is only available if we have
libfdt compiled in. If its not available return -1, which matches the
return code for no alias found.
This fixes the following error on omapl138_lcdk:
arm-linux-gnueabi-ld.bfd: drivers/built-in.o: in function `dev_read_alias_highest_id':
/home/mw/repo/u-boot/include/dm/read.h:986: undefined reference to `fdtdec_get_alias_highest_id'
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
This would make SPL build to DM_SPL, SPL_OF_CONTROL.
Build fine with but not tested.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board has flash chip on board so let store U-Boot environment there.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Per the boards config header file, there is no useful GPIO on these
boards. Remove CONFIG_CMD_GPIO from the defconfigs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
This is a sample GPT partition layout for SD card,
right now three important partitions are added to
make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x00000821 "loader1"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
guid: cbcbef44-e627-42bc-b134-93b6f3784b8c
2 0x00000822 0x00002821 "loader2"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
guid: f54eba28-d8de-4852-978d-1a673777e2ae
3 0x00002822 0x00020821 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93
Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin)
from MMC boot devices.
SPL related code is leveraged from FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
-----BEGIN PGP SIGNATURE-----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=rbBa
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc4
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
For passing the optional data of the load option to the loaded imaged
protocol we need its size.
efi_deserialize_load_option() is changed to return the size of the optional
data.
As a by-product we get a partial validation of the load option.
Checking the length of the device path remains to be implemented.
Some Coverity defects identified the load options as user input because
get_unaligned_le32() and get_unaligned_le16() is called. But non of these
Coverity defects can be resolved without marking functions with Coverity
specific tags.
Reported-by: Coverity (CID 303760)
Reported-by: Coverity (CID 303768)
Reported-by: Coverity (CID 303776)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is defined in the asm/cache.h header file. Update this header file to
include it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init
that is convenient for both DM_USB and u-boot traditional process.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot has video output enabled so time to get keyboard working.
=> usb reset;usb tree
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
| ALCOR Generic USB Hub
|
+-3 Mass Storage (12 Mb/s, 200mA)
Kingston DT 101 G2 001478544887BB3157380157
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 76mA)
ADATA ADATA USB Flash Drive 1520405012240002
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include NVME in the list of boot targets if CONFIG_NVME is enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The size is not actually used since it is present in the header. Drop this
parameter. Also tidy up error handling while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently we support reading a file from CBFS given the address of the end
of the ROM. Sometimes we only know the start of the CBFS. Add a function
to find a file given that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function currently returns a node pointer so there is no way to know
the error code. Also it uses data in BSS which seems unnecessary since the
caller might prefer to use a local variable.
Update the function and split its body out into a separate function so we
can use it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We may as well return the error code and use it directly in the command
code. CBFS still uses its own error enum which we may be able to remove,
but leave it for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot uses ulong for addresses but there are a few places in this driver
that don't use it. Convert this driver over to follow this convention
fully.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not definded anywhere.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.gpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot
will be located at address 0x16000. But, SPL will try to load the
payload from 0x24000 causing the boot to hang.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them
by CONFIG_SANDBOX instead of setting them in configs/sandbox.h.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the device firmware update functions to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
-----BEGIN PGP SIGNATURE-----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=o+Cy
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc3 (2)
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
Reference to commit that adds HDMI to other rk3399 boards:
commit 9778edae55 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI")
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide device path nodes for SATA devices.
This avoids creation of two handles with the same device path indicating
our root node.
This is what the device paths for a SATA drive with four partitions could
like:
/VenHw(..)/Sata(0x0,0xffff,0x0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(1,MBR,0x81ea591f,0x800,0x63ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(2,MBR,0x81ea591f,0x6400800,0x9ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(3,MBR,0x81ea591f,0x6e00800,0x16ef2ab0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(4,MBR,0x81ea591f,0x1dcf3800,0x1dcedab0)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI specification does not define a device sub-type for virtio.
Let's use a vendor hardware node here.
This avoids creation of two handles with the same device path indicating
our root node.
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI 2.8 specification has introduced the EFI_MEMORY_SP memory
attribute. Add it to the 'efidebug memmap' and 'efi mem' commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Add weak function which is called right after fdtdec_setup() configured
the U-Boot DT. This permits board-specific adjustments to the U-Boot DT
before U-Boot starts parsing the DT. This could be used e.g. to patch in
various custom nodes or merge in DT fragments from prior-stage firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
the mpc83xxx suvd3 variant is not longer used, so
remove it.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This macro is only used (tested for existence) in mpc83xx.c, which
unconditionally includes mpc83xx.h where it is unconditionally
defined. Removing it makes the remaining code easier to read.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
ls1046afrwy does not support sata boot.
So Override default BOOT_TARGET_DEVICES
and support only mmc, usb and dhcp as boot targets.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less
space to do malloc in flash environmet. Increase the value to get more
memory and also make it align with other boards(ls1046a, ls1043a etc.)
config values.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
BOOT command currently access spi-nor flash memory directly. As per spi-mem
framework, flash memory access via absolute addresses is no more possible.
Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MC_INIT command currently access spi-nor flash memory directly. As per
spi-mem framework, flash memory access via absolute addresses is no more
possible. Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
