The chip_desc.enable field is used only for muxes, not for switches.
Document it and remove the unused values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The Kconfig help has not been updated while adding PCA9547 and PCA9646.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The 'u-boot,i2c-transaction-bytes' device tree property provides
information regarding number of bytes transferred by a device in a
single transaction.
This change is necessary to avoid hanging devices after soft reset.
One notable example is communication with MC34708 device:
1. Reset when communicating with MC34708 via I2C.
2. The u-boot (after reboot -f) tries to setup the I2C and then calls
force_idle_bus. In the same time MC34708 still has some data to be sent
(as it transfers data in 24 bits chunks).
3. The force_idle_bus() is not able to make the bus idle as 8 SCL
clocks may be not enough to have the full transmission.
4. We end up with I2C inconsistency with MC34708.
This PMIC device requires 24+ SCL cycles to make finish any pending I2C
transmission.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Periphs bank offset must be applied on all pins and
PMX bank to prevent issue in meson_pinconf_set call.
Without offset on pins when a call to pinconf is done
meson_gpio_calc_reg_and_bit return wrong offset.
To avoid breaking pmx function offset is needed in pmx bank structure too.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
backport from linux:
931b18e92cd0 ("2c: meson: add configurable divider factors")
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Synchronize R-Car Gen3 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783,
has a TDSEL fix for R8A7790 H2 and R8A7794 E2 SoCs, implement
similar fix for U-Boot. The difference here is that the SoC
ES matching has to be implemented manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There exists code in drivers/common/common.c to read the dr_mode
from the device tree. This patch converts this driver to use that
function to initialize the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.
Example of the original output:
> USB0: USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch fixes the timer register setup in at91_wdt_start() to
correctly configure the register again. The input timeout value is
now in milli-seconds instead of seconds with the new watchdog API.
Make sure to take this into account and only use a max timeout
value of 16 seconds as appropriate for this SoC.
Also the check against a lower timeout value than 0 is removed. This
check makes no sense, as the timeout value is unsigned.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
This patch adds an alterative SPL version of atmel_serial_enable_clk().
This enables the usage of this driver without full clock support (in
drivers and DT nodes). This saves some space in the SPL image.
Please note that this fixed clock support is only added to the SPL code
in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL
should not be affected.
This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART
input clock. It defaults to 132096000 for ARCH_AT91 but can be set to
a different value if needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Before printk.h was introduced and MTDDEBUG was removed,
pr_crit() was calling MTDDEBUG(), which was since then
replaced by the current pr_debug().
pr_debug is more appropriate here.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new definition for ubi_assert and keep
the original one in an ifndef __UBOOT__.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcnoA9AAoJECaAFcEOcohNRYYH/0SAGKro+gO1q07xpBLGbOSL
MJPNDQ853IpH+kI+Mc+VFeFZz8fuQHae2aKfgmHmEGGSygFqAKXvMUgG73XO8Z27
Ov9r0RgR5s35eXFC0URqcDSCuTtFSP/MdmSy2hO546pJOapHhmx/eZUId3ZFjSe5
puIQfTxK0zbNqfFlfjsRnkXhR9jhYVvPtSpFYYjCeU/dRB4/OUzNHQjwjkdB8ru1
mTLmrhqqZ4fq3t9JMrxCH3COvI6QYBXj73ynKYtJ4lByh3NdIz0a37F99FiWgH2X
0WptUN8tjjZP+2BboVNo6io/12YxE6V+wG2LGEXreS9ubMr4nm+LXqDCoZIB7MM=
=ESBv
-----END PGP SIGNATURE-----
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
After the commit b9a2a0e2e9 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
There are no higher 16 writing corresponding bits for pmu_gpio0's
iomux/drive/pull at rk3288, need to read the value from register
firstly. Add the flag to distinguish it from normal registers.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Currently, HDMI driver doesn't consider minimum and maximum allowed rate
of pll3 (video PLL). It works most of the time, but not always.
Consider monitor with resolution 1920x1200, which has pixel clock rate
of 154 MHz. Current code would determine that pll3 rate has to be set to
154 MHz. However, minimum supported rate is 192 MHz. In this case video
output just won't work.
The reason why the driver is written in the way it is, is that at the
time HDMI PHY and clock configuration wasn't fully understood. But now
we have needed knowledge, so the issue can be fixed.
With this fix, clock configuration routine uses full range (1-16) for
clock divider instead of limited one (1, 2, 4, 11). It also considers
minimum and maximum allowed rate for pll3.
Fixes: 56009451d8 ("sunxi: video: Add A64/H3/H5 HDMI driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set MMCIF clock rate to 97.5 MHz, which is the default according
to Gen2 datasheet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Add code for configuring the MMC0CKCR/MMC1CKCR on Gen2 platforms.
This allows the MMCIF driver to set higher clock rate if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The $div and $mul values were swapped in the debug output,
fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The gen2_clk_get_sdh_div() function is supposed to look up the
$val value read out of the SDCKCR register in the supplied table
and return the matching divider value. The current implementation
was matching the value from SDCKCR on the divider value in the
table, which is wrong. Fix this and rework the function a bit
to make it more readable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
This patch fixes below warnings found with checker tool.
The variable len in i2c_msg struct is of unsigned type
and it is received as recv_count which is unsigned type
but it is checked with < 0 which is always false, hence
removed it.
The local variable curr_recv_count is declared as signed
type and compared aginst unsigned recv_count which is
incorrect. This is fixed by declaring it as unsigned type.
drivers/i2c/i2c-cdns.c: In function ‘cdns_i2c_read_data’:
drivers/i2c/i2c-cdns.c:317:18: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
if ((recv_count < 0))
^
drivers/i2c/i2c-cdns.c:340:24: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
updatetx = recv_count > curr_recv_count;
^
drivers/i2c/i2c-cdns.c:361:39: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
while (readl(®s->transfer_size) !=
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
Inactive chip-selects will give invalid values for read_sample so don't
consider them when trying to determine the overall min/max read sample.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/18]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Based on the JEDEC standard JESD79-3F. The tRAS timings should include
the highest speed bins at a given frequency. This is similar to commit
683c67b ("mv_ddr: ddr3: fix tfaw timimg parameter") where the wrong
comparison was used in the initial implementation.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/15]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a comment to explain the use of the hardcoded value for
the number of address cells in mvebu_get_tgt_attr(). This should help to
rework this function, once CONFIG_OF_LIVE is enabled for MVEBU in
general.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When booting on a 64-bit system, the boot_addr_start buffer is not
large enough to contain a 64-bit number, thus leading to a crash
even if fastboot_buf_addr is valid, only the high part of the address
will be printed to boot_addr_start :
fastboot with fastboot_buf_addr = 0x0000000006000000:
downloading of 92239872 bytes finished
Booting kernel at 0x00000000...
"Synchronous Abort" handler, esr 0x96000004
elr: 00000000010561f4 lr : 0000000001056fac (reloc)
<snip>
x28: 000000007df2d38f x29: 000000007df2d1b0
Resetting CPU ...
With this fix, boot_addr_start can have the full 64-bit address passed
to bootm.
Fixes: f73a7df984 ("net: fastboot: Merge AOSP UDP fastboot")
Cc: Simon Glass <sjg@chromium.org>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 801f1fa442 "dm: usb: udc: Use SEQ_ALIAS to index the USB gadget
ports" changed the way the udevice if found. It uses the alias to find
a udevice for a given USB port number. In the commit log it was stated
that if no alias is provided, the bind order will be used instead. However
it doesn't work. Fixing this by adding a call to uclass_get_device() if
uclass_get_device_by_seq() fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.
Fixes: 1161dbcc0a ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).
So we drop here the single steps and call just phy_connect_dev(...).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the spl system calls nand_init which does nothing.
It isn't until an attempt to load from NAND that it gets initialized.
Subsequent attempts to load just skip the initialization because
NAND is already initialized.
This moves the contents of mxs_nand_init to nand_init. In the event
of an error, it clears the number of nand chips found. Any
attempts to use nand will check if there are nand chips available
instead of actually doing the initialization at that time. If there
are none, it will return an error to the higher level calls.
Signed-off-by: Adam Ford <aford173@gmail.com>
Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled. This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
-----BEGIN PGP SIGNATURE-----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=JKJm
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc4-2' of https://github.com/xypron2/u-boot
Pull request for UEFI system for v2019.04-rc4
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
According to datasheet, the output on LDO regulators will start
appearing after 10-15 us.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Changing voltage and enabling regulator might require delays so the
regulator stabilizes at expected level.
Add support for "regulator-ramp-delay" binding which can introduce
required time to both enabling the regulator and to changing the
voltage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When stopping the ADC_V2_CON1_STC_EN should be cleared.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Our selftest will soon test the actual runtime reset function rather than
the boot time one. For this, we need to ensure that the runtime version
actually succeeds on x86 to keep our travis tests work.
So this patch implements an x86 runtime reset function. It is missing
shutdown functionality today, but OSs usually implement that via ACPI
and this function does more than the stub from before, so it's at least
an improvement.
Eventually we will want to have full DM functionality in runtime services.
But this fixes a travis failure and doesn't clutter the code too heavily, so
we should pull it in without the amazing new RTS DM framework.
Signed-off-by: Alexander Graf <agraf@suse.de>
Replace the current rather convoluted code using ad-hoc polling
mechanism with a more straightforward code. Use wait_for_bit_le32()
to poll the DDRCALSTAT register instead of local reimplementation.
It makes no sense to pull for 5 seconds before giving up and trying
to restart the EMIF, so instead wait 500 mSec for the calibration to
complete and if this fails, restart the EMIF and try again. Perform
this 32 times instead of 3 times as the original code did.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The EMIF reset code can well use wait_for_bit_le32() instead of all that
convoluted polling code. Reduce the timeout from 100 seconds to 1 second,
since if the EMIF fails to reset itself in 1 second, it's unlikely longer
wait would help. Make sure to clear the EMIF reset request even if the
SEQ2CORE_INT_RESP_BIT isn't asserted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The current EMIF clear timeout handling code was applying bitwise
operations to signed data types and as it was, was extremely hard
to read. Replace it with simple wait_for_bit(). Expand the error
handling to make it more readable too.
This patch also changes the timeout for emif_clear() from 14 hours
to 1 second.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The debug print is missing a newline, add it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The Altera Arria10 DDR driver was using constants in a few places
instead of reading registers associated with those constants, fix
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
EPHY CLK and RESET is available in Allwinner H3 EMAC
via mdio-mux node of internal PHY. Add the respective
clock and reset reg and bits.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Implement EMAC, GMAC clocks via ccu_clk_gate for
all supported Allwinner SoCs.
- Implement EMAC, GMAC resets via ccu_reset for all
supported Allwinner SoCs.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement EMAC clocks via ccu_clk_gate for Allwinner A10 SoC.
Which would eventually used in sunxi_emac.c driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This pull request contains bugfixes for rcar_i2c, rcar_ii2c and
i2c_cdns driver.
Also the commit "i2c: rcar_i2c: Add Gen3 SoC support" from Marek
is a bugfix for arm64 builds, as discussed with Marek on list.
Fix typo in axp_set_dldo() so that it correctly uses AXP818_DLDO1_CTRL
register to configure the voltage instead of setting AXP818_ELDO1_CTRL
register which is obviously incorrect.
Signed-off-by: Ondřej Jirman <megous@megous.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Cosmetic change. Any call to the recover function would need to do the
same check afterwards, so it's sensible to make it part of the function.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
It needs to be done for both reads and writes, so do it at rcar_i2c_xfer
to avoid duplication.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fix rcar_i2c_xfer return value, previously it was always returning
-EREMOTEIO when dealing with errors from calls to the read/write
functions.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Do the reset before clearing the MSR, otherwise it may result in a read
or write operation instead if the start condition is repeated.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Document the meaning of macros related to registers and values to be
written to them.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Setting up the delay only needs to be done once; move it to
rcar_i2c_set_speed so it's done at initialization time.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds support for handling arbitration lost
in case of multi master mode. When an arbitration lost
is detected, it retries for 10 times before failing.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The arbitration lost interrupt was not getting cleared
while clearing interrupts. This patch fixes this by adding
arbitration lost interrupt as well during clear. This patch
also removes hardcoded value and defined a macro for it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for R-Car Gen3 SoCs into the driver, which encompases
the Gen3 SoC extra timing register handling and 64bit build fixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Read ICSR only once to avoid missing interrupts. This happens on R8A7791
Porter during reset, when reading the PMIC register 0x13, which may fail
sometimes because of the missed DTE interrupt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Now the same SPI controller driver is reusable in all Allwinner
SoC variants, so rename the existing sun4i_spi.c into spi-sunxi.c
which eventually look like a common sunxi driver.
Also update the function, variable, structure names in driver from
sun4i into sunxi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- drop unused macros.
- use base instead of base_addr, for better code readability
- move .probe and .ofdata_to_platdata functions in required
places to add platdata support in future.
- use sentinel sun4i_spi_ids.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The usual SPI transmission protocol in Allwinner A10 and A31
controllers share similar context with minimal changes in register
offsets along with few additional register bits on A31.
So, add A31 spi controller support in existing sun4i_spi with A31
specific register offsets and bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLK support to enable AHB and MOD SPI clocks on sun4i_spi driver.
Clock disablement could be done while releasing the bus transfer, but
the existing code doesn't disable the clocks it only taken care of clock
enablement globally in probe.
So to make a proper clock handling, the clocks should enable it in claim
and disable it in release.
This patch would also do that change, by enable and disable clock in
proper order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Support fifo_depth via drvdata instead of macro definition, this would
eventually reduce another macro definition for new SPI controller fifo
depth support addition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Allwinner support two different SPI controllers one for A10 and
another for A31 with minimal changes in register offsets and
respective register bits, but the logic for accessing the SPI
master via SPI slave remains nearly similar.
Add enum offsets for register set and register bits, so-that
it can access both classes of SPI controllers.
Assign same control register for global, transfer and fifo control
registers to make the same code compatible with A31 SPI controller.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Stefan Mavrodiev <stefan@olimex.com> # A20-SOM204
- Implement SPI AHB, MOD clocks via ccu_clk_gate for all
supported Allwinner SoCs
- Implement SPI resets via ccu_reset for all supported
Allwinner SoCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
To drain rx fifo the fifo need to poll for how much data has
been filled up in rx fifo.
To achieve this, the current code is using wait_for_bit logic
on control register with exchange burst mode mask, which is not
a proper way of waiting for fifo filled up.
So, add code for polling rxfifo to be filled up using fifo
status register.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
With current order of include files, the file designware_spi.c
can't see that the struct global_data has the member
board_type when CONFIG_BOARD_TYPES is defined. By not seeing this
then all the members are shifted in the struct global_data.
So when the driver is trying to read from device tree blob, it
would pass the wrong address to the function 'fdtdev_get_int'.
This will make to use the default frequency 500000.
The fix consists of changing the order of include files in
designware_spi.c to include first common.h file.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since the datasheet Rev.1.00 has an error about the USB ID pin name,
this patch revises it.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50,
the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is selected,
and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Rev.1.50, the MOD_SEL0
bit16 is set to 0 when NFALE_A and NFRB_N_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Rev 1.50, the MOD_SEL0
bit2 is set when RX2_{A,B}, TX2_{A,B} and SCK2_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes the allocation name "RTSx_N_TANS_x" of IPSR /
MOD_SEL0/1 of r8a77990 to "RTSx_N_x". This information was
confirmed in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes the allocation name "sel_ndfc" of MOD_SEL2[22]
of r8a7796 / r8a77965 to "sel_ndf". This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch removes CC5_OSCOUT assignment of IP17[3:0] of r8a7795
/ r8a7796 / r8a77965. This information was confirmed in the R-Car
Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes to the correct names, and "_" is not include after
"adg" for r8a7795/r8a7796/r8a77965. This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch is change the bit assignment of "HDMI1_CEC" to "GP7_03",
and "HDMI0_CEC" to "GP7_02". This information was confirmed in the
R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
_omap3_spi_set_wordlen() indexed the regs->channel[] array with the
old wordlen (instead of the chipselect number) when reading the current
CHCONF register value. This meant it read from the wrong memory location,
modified that value, and then wrote it back to the correct CHCONF
register. The end result is that most slave configuration settings would
be lost, such as clock divisor, clock/chipselect polarities, etc.
Fixes: 77b8d04854 ("spi: omap3: Convert to driver model")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Currently, timer driver is bound only for hart0.
There is no mandatory requirement that hart0 should always
come up. In fact, HiFive Unleashed SoC hart0 doesn't boot
in S-mode because it only has M-mode.
The timer driver should be bound for boot hart.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is possible that input clock is not available because clk
device was not available and 'clock-frequency' DT property is
also not available.
In this case, instead of failing we should just skip baudrate
config by returning zero.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch adds fixed-factor clock driver which derives clock
rate by dividing (div) and multiplying (mult) fixed factors
to a parent clock.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver code for the SiFive FU540 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU540 device and
implements SoC-level clock tree controls and dividers.
Based on code written by Wesley Terpstra <wesley@sifive.com>
found in commit 999529edf517ed75b56659d456d221b2ee56bb60 of:
https://github.com/riscv/riscv-linux
Boot and PLL rate change were tested on a SiFive HiFive Unleashed
board.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
According to latest specification rev.0026 and after confirmation with
HW engineer, the DTCNTL register TAPNUM field must be set to 8 even on
H3 ES2.0 SoC. Make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
According to latest specification rev.0026, when HOST_MODE bit 0
(WMODE) is not set, HOST_MODE bit 8 (BUSWIDTH) is ignored. Clear
HOST_MODE bit 8 in such case and align the code with Linux and
avoid possible unforeseen issues.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop per SoC def_bool on each driver, since this is now implied by
SoC Kconfig option instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop per SoC def_bool on each driver, since this is now implied by
SoC Kconfig option instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
gpio_get_value should return 0 or 1, not the value of bit & (1 << pin)
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release.
Migrate TEGRA_KEYBOARD from headers to Kconfig, only the seaboard uses it but we
drop CONFIG_KEYBOARD as the driver doesn't use the legacy drv_keyboard_init.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate SYS_I2C_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable sound on samus using the broadwell I2S and an RT5677 audio codec.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a sound driver for samus which ties together the audio codec and
I2S controller.
For now broadwell_sound is commented out in the makefile since we cannot
compile it without sound support enabled. The next commit fixes this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
I2S is used to send digital audio data to an audio codec. Add support for
this on broadwell.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sound driver which can output simple beeps using this legacy timer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sound support for link, using the HDA codec implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When testing the sound system we don't need the hear the beeps. The
testing works by checking the data that would be emitted. Add a
device-tree property to silence the sound, and enable it for testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel High-definition Audio is a newer-generation audio system which
provides for transfer of a large number of audio stream, each containing
up to 16 channels.
Add support for HDA as a library which can be used by other drivers.
U-Boot currently uses only two channels (stereo).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some audio codecs such as Intel HDA do not need to use digital data to
play sounds, but instead have a way to emit beeps. Add this interface as
an option. If the beep interface is not supported, then the sound uclass
falls back to the I2S interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This method in the sound API is optional since some drivers can do this
when probing or as part of SoC init. Mark it as such.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the PCH has 4 operations and these are reasonably widely used
in the drivers. But sometimes we want to add rarely used operations, and
each of these currently adds to the size of the PCH operations table.
Add an ioctl() method which can be easily expanded without any more impact
on the operations table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass currently has no tests. Add a sandbox driver and some simple
tests to provide basic coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: Use "sandbox,pch" for the compatible string, for consistency]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this uclass is selected only on x86. In order to add a test for
it, it must also support sandbox. Create a new CONFIG_PCH option and
enable it on x86 and sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not used outside this file so make it static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this driver does not check whether it is able to actually
communicate with the I2C controller. It prints a timeout message but still
considers the probe to be successful.
To fix this, add some checking that the init succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present it is not possible to use the syscon devices for PCI devices
since a regmap is required. Since PCI uses a 3-cell address the conversion
of the 'reg' property to an address always fails. In any case, the regmap
is not useful with PCI since devices are accessed through the PCI bus
which regmap does not support.
Add a special case for PCI syscon devices, so that they don't set up a
regmap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Before the patch scsi would report the same device number for all SCSI
devices, e.g.
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 0: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
With the patch the same device number is reported as is used in
scsi_read():
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 1: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fsl_ddr_board_options is generally defined in board
board's ddr.c, but some boards like lx2160ardb board
does not need this function.
Defining fsl_ddr_board_options as weak function to
resolve compilation errors for such boards.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[PK: Fix checkpatch warnings]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch prevent the Stratix 10 FPGA driver incorrectly return the
transaction ID as the mailbox error code. It should always return the
actual mailbox error code from SDM firmware.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set the HOST_MODE register WMODE bit according to the SDHI bus width,
that is 0 for 64bit bus and 1 for 16/32bit bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch adds support to load 24bpp BMP files on 16bpp displays. This
will be used by the theadorable board. The "old" bmp command did support
this operartion mode and to not break compatibility with the move to
DM_VIDEO, we need to add this support to the "new" bmp code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
There are HDMI displays where hpd pin is not connected, thus
we cannot get it to work unless we specifically set the resolution.
Rework the display probing, so hotplug detect failure causes
fallback to probing ddc for EDID data.
Signed-off-by: Priit Laes <priit.laes@paf.com>
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbca ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add native tsc calibration function. Calibrate the tsc timer the same
way as linux does in arch/x86/kernel/tsc.c.
Fixes booting for Apollo Lake processors.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The dm_gpio_set_value() routine sets signal logical level, with
GPIO_ACTIVE_LOW/HIGH value taken into account. Reset active value is 1
(asserted), while reset inactive value is 0 (de-asserted). Fix the reset
toggle code to set the correct reset logic value.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
At present there is still some samsung-specific code in the audio codecs.
Remove it so that these can be used by other SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow misc devices to have children, so that we can use this uclass for
cases where a child device (e.g. I2S) needs to access a misc driver for
transferring data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while enabling io regulators. This way the driver doesn't see an error
when disabling an always-on regulator and when enabling is not supported.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit e17e0ceb83.
It is advised to return an error when trying to disable an always-on
regulator and let the consumer driver handle the error if needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
While uclass_find_device() fails with -ENODEV in case of list_empty
strangely uclass_find_first_device() returns 0.
Fix uclass_find_first_device() to also fail with -ENODEV instead.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
To activate the csg option, the driver need to set the bit2
of PLLNCR register = SSCG_CTRL: Spread Spectrum Clock Generator
of PLLn enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of clk dump command and
display information during probe (under CONFIG_DISPLAY_CPUINFO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Because stgen is initialized with HSI clock, we need to
recalculate the counter when changing frequency.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove support of ck_usbo_48m clock node in device tree,
but force 48MHz frequency to prepare alignment
with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver
as this driver is used in NXP based SoCs
It is necessary to have Serial console running before relocation
The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround"
for DM problem : 4687919684
This flag is set if board does not support device-tree and using
platform data, In DM Model either of device tree or platform data
can be used to fetch device configuration
It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout
corresponding device tree description (OF_CONTROL)
Other board/SoCs have this flag set unconditionally
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
This driver is used on several big endian mips board.
So we could use raw I/O function instead of forcing
big endian access.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy,
do not poll for the completion status using CMD13, but rather wait 50mS.
Once the card receives the CMD6 and starts executing it, the bus is in
undefined state until both the card finishes executing the command and
until the controller switches the bus to matching timing configuration.
During this time, it is not possible to transport any commands or data
across the bus, which includes the CMD13.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The internal DMAC asserts DMA transfer end bit too early on older
version of the TMIO IPs which use bit 17 for DTRAEND. Add 1uS
delay after the completion of DMA transfer and before invalidating
the cache to let the DMAC fully complete the transfer. Otherwise,
it could happen that the last few bytes of a transferred data are
not available.
A test case to trigger this behavior is the following command, ran
on the U-Boot command line, with Sandisk 16 GiB UHS-I card inserted
into SDHI slot 0 and with first partition being of type FAT:
=> while true ; do mmc rescan ; fstype mmc 0:1 ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Different versions of the SDHI core use either bit 17 or bit 20 for the
DTRAEND indication, which can differ even between SoC revisions. Make
the DTRAEND bit position part of the driver private data, so that the
probe function can set this accordingly. Set this to 20 on Socionext
SoCs and either 17 or 20 on Renesas SoCs, depending on the SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add non DM version of SPI_MEM to support easy migration to new SPI NOR
framework. This can be removed once DM_SPI conversion is complete.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
It is necessary to call spi_claim_bus() before starting any SPI
transactions and this restriction would also apply when calling spi-mem
operations. Therefore claim and release bus before requesting transfer
via exec_op.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Extend spi_mem_adjust_op_size() to take spi->max_write_size and
spi->max_read_size into account.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SPI controllers support all types of SPI modes including dual/quad bus
widths. Therefore remove constraint wrt SPI mode from spi-mem layer.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
- Move Armada XP / 38x PCIe driver to DM_PCI from me
- Move Armada XP / 38x LCD driver to DM_VIDEO from me
- Add uDPU board (Armada-3720) from Vladimir
[trini: Fix warning in pci-uclass.c by removing ret from
pci_uclass_child_post_bind as it no longer calls functions with
a return code to catch.]
Signed-off-by: Tom Rini <trini@konsulko.com>II
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.
To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This function will be used by the Marvell Armada XP/38x PCIe driver,
which is moved to DM right now. So let's extract the functionality
from pci_uclass_child_post_bind() to make it available.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
The OMAP36 and DM37 TRM state to disable extneded drain IO before
changing the PBIAS. This patch does this before pmic writes if
the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is
omap36xx
Signed-off-by: Adam Ford <aford173@gmail.com>
After the merge of the new, generic pinctrl-code, the include for
rockchip/Kconfig was missing. Add it here, so we can select the
pinctrl-driver for SPL.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To make adding new subdirectories easier, let's enforce alphabetical
ordering of the includes of Kconfig files in the respective
subdirectories.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These clocks are needed to get MMC running. We don't actually support
setting them yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It is helpful to print the clock number as well as the index, so that this
can be looked up in the binding file. Update the debug() statement to do
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we used the pinctrl-rockchip driver, these code is not needed,
so remove them.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use this driver to fit all Rockchip SOCs and to support
the desired pinctrl configuration via DTS.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a sound driver for rk3288 supporting chromebook_jerry. This uses the
I2S driver, and existing audio codec and the clock/pinmux support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a driver for I2S which allows audio data to be sent from the SoC to
the audio codec. The sample rate and other settings are hard-coded for now
as there is no suitable device-tree binding available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for setting pinctrl and clock for I2S on rk3288. This allows
the sound driver to operate. These settings were created by rkmux.py
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If the host does not respond in time, the initialization fails. However
the usb ether driver will still be registered. This will make
usb_gadget_probe_driver() fail the next time the initialization is
attempted because it cannot find an available UDC.
Fixing this by calling _usb_eth_halt() when the init fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This functions can be reused by other MSCC SoCs therefore,
make them more generic and move them in separate files.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
