Commit graph

8718 commits

Author SHA1 Message Date
Adam Ford
20188f519a ARM: dts: Rename logicpd-toredp-37xx-devkit in U-Boot
In U-Boot, this device tree is compatible with both the Torpedo and
SOM-LV kits.  Let's rename it in the device tree since the U-Boot code and
show a more generic OMAP3 name.  The code auto detects between the two and
loads the proper DTB file for Linux.  This would eliminate the SOM-LV showing
the name Torpedo during boot and hopefully eliminate some confusion.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-11-29 22:30:50 -05:00
Ludovic Desroches
aaa4ba930c board: atmel: add sama5d2_ptc_ek board
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-11-29 22:30:50 -05:00
Ludovic Desroches
48e4851f49 ARM: at91: add sama5d2 smc header
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
c729fb258a mach-stm32: Factorize MPU's region config for STM32 SoCs
MPU's region setup can be factorized between STM32F4/F7/H7 SoCs family
and used a common MPU's region config.

Only one exception for STM32H7 which doesn't have device area
located at 0xA000 0000.

For STM32F4, configure_clocks() need to be moved from arch_cpu_init()
to board_early_init_f().

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
014a953c4a stm32: migrate clock structs in include/stm32_rcc.h
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
4e97e25723 clk: clk_stm32fx: add clock configuration for mmc usage
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.

STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.

Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
c88c6a9e03 clk: stm32fx: migrate define from rcc.h to driver
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
1555903c8d ARM: DTS: stm32: update rcc compatible for STM32F746
Align the RCC compatible string with the one used by kernel.
It will allow to use the same clock driver for STM32F4
and STM32F7 and to manage the differences between the 2 SoCs

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
d0a768b1c8 clk: stm32f7: retrieve PWR base address from DT
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
d3651aac46 ARM: DTS: stm32: add pwrcfg node for stm32f746
This node is needed to enable performance mode
when system frequency is set up to 200Mhz.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Marek Vasut
02e80f0c11 ARM: rmobile: Migrate boards to RCar IIC drivers
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
d7f0b85269 ARM: rmobile: Use PRR driver on all Gen3 boards
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
aff151e5b2 ARM: rmobile: Convert PRR to DM and OF control
Implement DM driver for the Renesas PRR into RCar cpu info and convert
all users with DM and OF enabled to this new driver. This means all of
the boards with DM and OF enabled can fetch PRR address from DT, which
is useful on ie. V3M which has different PRR address than the rest of
Gen3 SoCs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
ef5f1979ff ARM: rmobile: Zap checkboard on Gen3
The checkboard() function showing hard-coded board model for which the
U-Boot was built is superseded on Gen3 by show_board_info() displaying
the Model from device tree. Add small ifdef to stop compiling the
function into U-Boot.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
f2b2bd6660 ARM: rmobile: Unify R8A7795 and R8A7796 in rmobile Makefile
Since both R8A7795 and R8A7796 now use the same files, unify the
Makefile entry to CONFIG_RCAR_GEN3.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
a523af69e8 ARM: rmobile: Unify memory map for RCar Gen3
Unify the R7A7795 and R8A7796 memory maps in memmap-gen3 and, for now,
select which one is used based on which SoC is selected. Since this is
done in C code instead of statically assigned now, the decision can be
taken by PRR SoC match as well, which will be done in a subsequent patch.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
262e91566f ARM: rmobile: Add PRR CPU ID macros
Replace the ad-hoc values in the PRR CPU ID table with macros,
so that users can use rmobile_get_cpu_type() can compare the
returned value with these macros to figure out on which CPU they
are running.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
654f37da64 ARM: rmobile: Dispose of r8a779x.h for Gen3
These files no longer contain anything useful, so remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
5271dda050 ARM: rmobile: Zap Gen3 PFC tables
These old PFC tables are no longer needed as there is now a proper
PFC pinmux driver in drivers/pinctrl/renesas . Remove them .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
d4bde6fa18 ARM: rmobile: Drop SDHI address macros from Gen3
Since the RCar Gen3 no longer uses the SH SDHI driver, but rather
uses the Matsushita SD driver, which loads all the properties from
device tree, these macros are no longer used, remove them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
5d1b875dfa ARM: rmobile: Fix eMMC signal voltage on ULCB
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for ULCB to describe the hardware correctly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Tom Rini
b06c46de63 Xilinx changes for v2018.1
Zynq:
 - Add support for Syzygy and cc108 boards
 - Add support for mini u-boot configurations (cse)
 - dts updates
 - config/defconfig updates in connection to Kconfig changes
 - Fix psu_init handling
 
 ZynqMP:
 - SPL fixes
 - Remove slcr.c
 - Fixing r5 startup sequence
 - Add support for external pmufw
 - Add support for new ZynqMP chips
 - dts updates
 - Add support for zcu102 rev1.0 board
 
 Drivers:
 - nand: Support external timing setting and board init
 - ahci: Fix wording
 - axi_emac: Wait for bit, non processor mode, readl/write conversion
 - zynq_gem: Fix SGMII/PCS support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
 MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
 =BqNN
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.1

Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling

ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board

Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
2017-11-29 08:26:07 -05:00
Michal Simek
b8d4497f99 arm: zynq: Change Zynq/ZynqMP Kconfig description
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:40 +01:00
Wilson Lee
310995d9f9 mtd: zynq: nand: Move board_nand_init() function to board.c
Putting board_nand_init() function inside NAND driver was not appropriate
due to it doesn't allow board vendor to customise their NAND
initialization code such as adding NAND lock/unlock code.

This commit was to move the board_nand_init() function from NAND driver
to board.c file. This allow customization of board_nand_init() function.

Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:40 +01:00
Michal Simek
30829447a4 arm: zynq: Use unsigned type with comparison with ARRAY_SIZE
Sparse is return warning about this:
arch/arm/mach-zynq/slcr.c: In function 'zynq_slcr_get_mio_pin_status':
arch/arm/mach-zynq/slcr.c:185:16: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
  for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
                ^

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:39 +01:00
Michal Simek
11ea6f556c arm: zynq: Add support for EMIT_WRITE operation
Add proper support for EMIT_WRITE operation which is write only.
Do not use EMIT_MASKWRITE which is read-modify-write.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:39 +01:00
Michal Simek
f29074803c arm: zynq: Add ps7GetSiliconVersion() to ps7_spl_init
Unfortunately camelcase is coming from ps7_init* format.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:39 +01:00
Michal Simek
c0823a76df arm: zynq: Move common ps7_init* initialization to arch code
This patch is based on work done in topic board where the first address
word also storing operation which should be done. This is reducing size
of configuration data.
This patch is not breaking an option to copy default ps7_init_gpl* files
from hdf file but it is doing preparation for ps7_init* consolidation.

The patch is also marking ps7_config as weak function.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:39 +01:00
Michal Simek
f0b619ec29 arm: zynq: Move ps7_* to separate file
Extract ps7_* from spl code to prepare for extension.
And also return value.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:39 +01:00
Michal Simek
96b96adf0b arm: zynq: Add missing ps7_post_config declaration
Add missing declaration to header.

Warning log:
arch/arm/mach-zynq/spl.c:94:12: warning: symbol 'ps7_post_config' was
not declared. Should it be static?

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:38 +01:00
Masahiro Yamada
b443fb4210 ARM: dts: uniphier: Sync with Linux 4.15-rc1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:29:00 +09:00
Masahiro Yamada
10c62f41e3 ARM: uniphier: remove XIRQ pin settings
The XIRQ pins are now set up on the Linux side by the GPIO hogging.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Masahiro Yamada
eadd95a97e ARM: uniphier: remove IRQ settings
This work-around has been here in U-Boot because the AIDET and GPIO
drivers were missing in the upstream Linux.  Both are now available
in Linus' tree:
  - drivers/irqchip/irq-uniphier-aidet.c
  - drivers/gpio/gpio-uniphier.c

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Masahiro Yamada
ed3986ca30 bitops: collect BIT macros to include/linux/bitops.h
Same macros are defined in various places.  Collect them into
include/linux/bitops.h like Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Shubhrajyoti Datta
fe16aa4b02 arm64: zynqmp: Enable watchdog by default
Enable watchdog in dts for zcu102.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:17 +01:00
Michal Simek
b10255f8e0 arm64: zynqmp: Add note about si5328 interrupt
Add comment about irq present on the board connected to PL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:16 +01:00
Anurag Kumar Vulisha
8861dcf2b9 arm64: zynqmp: usb: Correct IOMMU node for making SMMU work with USB
This patch makes SMMU work by moving the iommus node under the dwc3 child
entry from parent node.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:16 +01:00
Michal Simek
a41bd46c2a arm64: zynqmp: Remove clock setting from dtsi
clock setting is handled via clk dtsi file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:16 +01:00
Anurag Kumar Vulisha
397a08ab92 arm64: zynqmp: Uncomment snps,quirk-frame-length-adjustment flag in dwc3
This patch uncomments snps,quirk-frame-length-adjustment which has
the value to adjust the SOF/ITP generated from the controller.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:16 +01:00
Manish Narani
2ef98667b7 arm64: zynqmp: Add USB OTG interrupts support in dt
This patch adds OTG interrupt support in device tree. It will add
an extra interrupt line number dedicated to OTG events. This will
enable OTG interrupts to serve in DWC3 OTG driver.

Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:16 +01:00
Manish Narani
f7346ef14c arm64: zynqmp: Enabled CCI support for USB
This patch adds CCI support for USB when CCI is enabled in design.
This patch also adds 'reg' property for Xilinx USB 3.0 IP. The 'reg'
property is added in order to modify a register in that to enable
coherency in Hardware.

Also add address to unit name to avoid dtc warning

Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Anurag Kumar Vulisha
8e5a4e6f0e arm64: zynqmp: Add support reading SoC revision using nvmem driver in dwc3
This patch adds support for reading silicon revision using zynqmp nvmem
driver.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Michal Simek
b0c55207bf arm64: zynqmp: Move nodes which have no reg property out of bus
Nodes without reg properties shouldn't be placed in amba node.
Move them out.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Michal Simek
795ebc0e64 arm64: zynqmp: dt: Add AMS node
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.

Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Manish Narani
5e3c90d238 arm64: zynqmp: sdhci: set host quirk2 for no 1.8V support for 1.0 silicon
This patch sets host quirk2 bit field for No 1.8V supported in case of
1.0 silicon. The 1.0 silicon doesn't have support for UHS-I modes. This
property will ensure the SD runs on High Speed mode.

Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Anurag Kumar Vulisha
0aada397b5 arm64: zynqmp: Use reset controller framework for asserting/de-asserting reset
This patch modifies the phy_zynqmp.c driver to use reset-controller
framework for asserting/de-asserting reset for High Speed modules.

Also fix documentation and dtsi.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Anurag Kumar Vulisha
98ad47bfab arm64: zynqmp: Add reset-controller support in serdes driver
This patch add the reset nodes in zynqmp.dtsi which are used by
reset-controller framework

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Michal Simek
3940bca4a8 arm64: zynqmp: Remove tx_termination_fix detection on silicon v1
Only silicon v1 requires this termination fix. With new nvmem soc
revision nvmem detection driver this can be autodetected at run time and
this flag is not needed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Nava kishore Manne
0d87c4fd9b arm64: zynqmp: Add support for zynqmp nvmem firmware driver
Add support for zynqmp nvmem firmware driver.

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:15 +01:00
Michal Simek
ae9775f822 arm64: zynqmp: Add support for zcu102 1.0 rev
1.0 rev is the latest rev. Describe information in eeprom.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:11 +01:00
Michal Simek
9c77cb73c7 arm64: zynqmp: Update device tree for pinmux
Added pin control support in device tree for zynqmp.

Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:10 +01:00
Michal Simek
6507be7800 arm64: zynqmp: Remove local-mac-address from dtsi file
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
5fe03269f2 arm64: zynqmp: Use SPDX license with dc4
Just header change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
b9f7edee07 arm64: zynqmp: Remove leading 0s from mtd table for spi flashes
dtc reports issues with it.
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
816019a8d4 arm64: zynqmp: Add missing alias for gem0 for ep108
Add missing alias for gem0 for ep108 to have proper sequence number.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Bharat Kumar Gogada
f811eca9db arm64: zynqmp: zcu102: Modifying GTR lane-0 to PCIe
- Enabling GTR lane-0 to PCIe
- Enabling PCIe node in device tree

Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Chirag Parekh
d801ce553e arm64: zynqmp: Update device tree for gpio
Used defines rather than raw values for gpio configurations.

Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
582ee92417 arm64: zynqmp: Add revB string to compatible string
Some user space libraries reading platform compatible string and based
on that changing behavior. Mark revB board with revB string.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
23b34d1456 arm64: zynqmp: Use revision in dts file description
Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Jyotheeswar Reddy Mutthareddyvari
5f9b083cdb arm64: zynqmp: PM: Specify power domains for DP related nodes
Currently DP power domain (pd_dp) is not attached to any of the DP nodes which is
causing genpd to trigger a power down request for DP domain, making all DP related
peripherals unusable. So assign power domains for all DP related nodes to enable
proper accounting of DP power domain usage.

Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Naga Sureshkumar Relli
10f2a292b1 arm64: zynqmp: disable smmu
This patch disables the smmu and also removes the mmu-masters

Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Nava kishore Manne
4d9d69856f arm64: zynqmp: rtc: Add calibration
This patch adds the calibration property with required value,
calculated based on rtc input crystal oscillator frequency (32.768Khz).

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Anurag Kumar Vulisha
110d06b2e3 arm64: zynqmp: Add SMMU support for SATA IP
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below

	SATA SMMU ID =  <TBU number>, 0011, 00, 00, AXI ID[1:0]
	Note: SATA in  ZynqMp uses TBU1 so TBU number = 0x1, so
	      SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]

Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values

 Read ID/ Write ID for Non-Data Port0 transfers = 0
 Read ID/ Write ID for Data Port0 transfers = 1
 Read ID/ Write ID for Non-Data Port1 transfers = 2
 Read ID/ Write ID for Data Port1 transfers = 3

Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Rob Herring
ec2b2d4c53 arm64: dts: xilinx: fix PCI bus dtc warnings
dtc recently added PCI bus checks. Fix these warnings.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Michal Simek
0b33e0b156 arm64: zynqmp: Add missing gpio property to dtsi
All gpio controllers should contain this property.
This property is not checked by the code that's why this issue wasn't
found earlier.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Hyun Kwon
834ec8e9dd arm64: zynqmp: Update the GPU address size
The correct register size is 0x10000, otherwise
it overlaps with other register space.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Madhurkiran Harikrishnan
59206dd1e3 arm64: zynqmp: Add clock name for GPU
This patch will add names to the clocks used by GPU.

Signed-off-by: Madhurkiran Harikrishnan <madhurki@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Nava kishore Manne
7689dce753 arm64: zynqmp: Label whole PL part as fpga_full region
This will simplify dt overlay structure for the whole PL.

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Michal Simek
6db82e0956 arm64: zynqmp: Fix broken architected timer interrupt trigger
Extract from Linux mainline patch:
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).

A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.

The respective maintainers are of course welcome to prove me wrong.

While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).

Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Soren Brinkmann
19ee402d08 arm64: zynqmp: PM: Add IRQ
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Jolly Shah
6a097b0d05 arm64: zynqmp: Reduced min-residency time for idle state node
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.

Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Jyotheeswar Reddy
fec547397f arm64: zynqmp: DT: Fix typo in idle-states node definition
Fixed a typo in specifying "entry-method"

Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Shubhrajyoti Datta
941f61fe80 arm64: zynqmp: Update the OPPs for cpu freq
Add operating-points-v2.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
585ca873ef arm64: zynqmp: Add references to cpu nodes
Add missing references to all cpu nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
40d1f8af17 arm64: zynqmp: Wire QSPI boot mode for SPL
ZynqMP qspi driver is on the way to mainline

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:02 +01:00
Michal Simek
494fffe70d arm64: zynqmp: Add support for CG/EG/EV device detection
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.

These efuse bits are setup for certain devices.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
011f0c4f7c arm64: zynqmp: Add SD1 level shifter mode to alternative selection
Extend Kconfig to cover SD1 level shifter mode.

Reported-by: Jason Wu <jason.hy.wu@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Siva Durga Prasad Paladugu
89401481bd arm64: zynqmp: Enable config DEFINE_TCM_OCM_MMAP if CONFIG_MP defined
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
c85a6b79d1 tools: mkimage: Extend mkimage to also include pmufw
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.

This is generated command line when PMUFW_INIT_FILE is setup.

./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:57 +01:00
Siva Durga Prasad Paladugu
e042d36e17 arm64: zynqmp: Provide a Kconfig option to use specified memory for MMU table
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Siva Durga Prasad Paladugu
f322ad604e arm64: zynqmp: mp: Correct the R5 release sequence
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
   A53 can do speculative and may result in ECC failures
   if TCM's are not initialized. So, it is always better
   to disable dcaches before accessing TCM and enable back.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Michal Simek
62e950fad3 arm64: zynqmp: Remove slcr with mio status pin detection
This code is not used on this platform and it is not called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:55 +01:00
Michal Simek
dea4d2f01d arm: zynq: Add mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.

ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE  0x40000
was hardcoded.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:47 +01:00
Michal Simek
70ca290422 arm: zynq: Sort dts names
Sort names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:45 +01:00
Michal Simek
bc133e80ae arm: zynq: Add board support for cc108
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:40 +01:00
Michal Simek
534f7e0235 arm: zynq: Sync location of DT properties with Linux
This is trival change which only ensures the same location with Linux
kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Sai Pavan Boddu
5fad1ab3d0 arm: zynq: Add device-type property for zynq ethernet phy nodes
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Chirag Parekh
57bcc7fd37 arm: zynq: Add SCL & SDA GPIO entries for recovery
Wire i2c pinmuxing gpio recovery for zc702.

Signed-off-by: Chirag Parekh <chiragp@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom McLeod
413ab5b0e1 arm: zynq: Add support for SYZYGY Hub board
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.

Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Heinrich Schuchardt
549d684d4e arm64: zynqmp: remove unnecessary logical constraint
In

if (a || b)
else if (!a)

the constraint (!a) is always true if else is reached and
can be removed.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Jagan Teki
52aaddd6f4 i.MX6: engicam: Add imx6q/imx6ul boards for existing boards
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
539b1e228f board: icore-rqs: Fix mmc get env device
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3

Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
152038ea18 i.MX6UL: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
1f6e9bd2a7 i.MX6Q: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Fabio Estevam
e2162d709f imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.

It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.

While at it, rename it to imx_wdog_disable_powerdown().

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-27 10:34:49 +01:00
Fabio Estevam
b42287f4c9 imx: Also clear powerdown enable bit for WDOG3 on i.MX6ULL
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.

Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:40 +01:00
Fabio Estevam
23ecca2cd8 mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:31 +01:00
Philipp Tomsich
f07d76c00d rockchip: fix turning off boot-mode via Kconfig
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.

Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome.  Instead this check can easily be performed in
the C-code.

This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.

Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-26 14:57:11 +01:00
Philipp Tomsich
8c2bb589e2 rockchip: pinctrl: rk3399: add support for I2C8
The RK3399 has a total of 9 I2C controllers.  To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.

For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-26 00:39:08 +01:00
Andy Yan
ecb103bf68 rockchip: check download key before bootup
Enter download mode if the download key pressed.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Converted printfs in boot_mode.c to debug/pr_err:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:24 +01:00
Andy Yan
b4d23f7643 rockchip: add support for enter to bootrom download mode
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Andy Yan
e3067793c3 rockchip: make boot_mode related codes reused across all platforms
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Kever Yang
6ba54058ed rockchip: sysreset: merge into one common driver
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
4bbb05bcb5 rockchip: rk3188: move CONFIG_SPL_* entries from rk3188_common.h to Kconfig
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig.  This migrates those over to
Kconfig.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
b82bd1f8d4 rockchip: back-to-bootrom: allow passing a cmd to the bootrom
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it.  There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.

All the existing call-sites are adjusted to match the changed function
signature.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
4d9253fb76 rockchip: rk3188: use boot0 hook to load up SPL in 2 steps
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.

With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.

Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ecfd71891a rockchip: back-to-bootrom: replace assembly-implementation with C-code
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.

This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b4806d6f1f arm: provide a PCS-compliant setjmp implementation
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers.  One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.

To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ff143d5556 arm: mark save_boot_params_ret as a function
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32.  By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.

Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
7776cc011d arm: make save_boot_params_ret prototype visible for AArch64
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).

This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b377d22264 rockchip: boot0 hook: support early return for RK3188/RK3066-style BROM
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.

To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
16d761e3dd bcm281xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
62269f02ab bcm235xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 5
- ran 'whitespace-cleanup'
2017-11-21 23:57:21 +01:00
Philipp Tomsich
a002077d7d socfpga: boot0 hook: adjust to unified boot0 semantics
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
14ad6eb264 rockchip: enable boot0-hook for all Rockchip SoCs
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
  instruction load and running by bootrom;

Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-11-21 23:57:21 +01:00
Kever Yang
cee7470cd8 rockchip: boot0: align to 0x20 for armv7 '_start'
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
ef70a42f0f arm: boot0 hook: move boot0 hook before '_start'
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.

To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
  (1) if a boot0-hook is present it is inserted at the start of
      the image
  (2) if a boot0-hook is present, emitting the ARM vector table
      (and the _start) symbol are suppressed in vectors.S and
      the boot0-hook has full control over where and when it
      wants to emit these

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Antony Antony
6130b1f6bc sun50i: h5: Add NanoPi Neo Plus2 DT initial support
Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:57 +05:30
Antony Antony
8faac0941c arm64: sun50i-h5.dtsi : update to kernel 4.14
last Kernel commit of sun50i-h5.dtsi d86e63e1f0b7

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:47 +05:30
Faiz Abbas
16fa2eb951 ARM: dra7: Kconfig: Add thermal configs for dra7xx and am57xx
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-21 08:03:39 -05:00
Faiz Abbas
12dd1e5c6a ARM: dts: OMAP5+: Add support for bandgap sensor in SPL
Mark bandgap node as uboot,dm-spl so that it can be accessed in spl

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-11-21 08:03:38 -05:00
Beniamino Galvani
456efb5127 odroid-c2: enable I2C
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-20 10:11:44 +01:00
Beniamino Galvani
f8d9ca1833 i2c: add Amlogic Meson driver
Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-20 10:11:34 +01:00
Fabio Estevam
74da017a49 mx6: Select MX6QDL option via Kconfig
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-20 10:01:35 +01:00
Peter Senna Tschudin
6b0071c110 mx53: Add Board support for GE PPD
Create board support for GE PPD, based on mx53loco.

Use mx53ppd_defconfig make target to configure for this board.

Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:59:02 +01:00
Martyn Welch
54d8d4942f arm: mx5: Add more register definitions
Add register definitions require for video configuration.

Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Martyn Welch
065a1ece7a pwm: imx: Enable PWM support on i.MX53
Add missing parts for i.MX53 PWM support

Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Landheer-Cieslak, Ronald
48c7f77128 Add UART base addresses for additional UARTs
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.

Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17 10:53:45 -05:00
Jorge Ramirez-Ortiz
9a16153834 configs: dragonboard410c: Save environment data on eMMC
Save the environment data at the end of the boot partition on emmc

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-11-17 07:44:13 -05:00
Kever Yang
21f4486faa armv8: update gd after relocate
We need to update gd in assamble code after relocate,
this is a fix to:
adc421e arm: move gd handling outside of C code

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-17 07:44:13 -05:00
Stephen Warren
49e93875a6 arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17 07:44:13 -05:00
Neil Armstrong
ea990816fe arm: meson: Add supplementary ethernet registers definitions
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17 07:44:13 -05:00
Masahiro Yamada
d6a0c78a4e pylibfdt: compile pylibfdt only when dtoc/binman is necessary
Currently, pylibfdt is always compiled if swig is installed on your
machine.  It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.

"checkbinman" and "checkdtoc" are wrong.  It is odd that the final
build stage checks if we have built necessary tools.  If your platform
depends on dtoc/binman, you must be able to build pylibfdt.  If swig
is not installed, it should fail immediately.

I added PYLIBFDT, DTOC, BINMAN entries to Kconfig.  They should be
property select:ed by platforms that need them.  Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-17 07:43:32 -05:00
Neil Armstrong
cade865a43 arm: add initial support for Amlogic P212 based on Meson GXL family
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17 07:43:32 -05:00
Neil Armstrong
4862215649 ARM: dts: Synchronize Amlogic from Linux Mainline 4.13.5
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5

In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17 07:43:32 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Tom Rini
ebca2083d3 Merge git://www.denx.de/git/u-boot-marvell 2017-11-16 09:32:04 -05:00
Baruch Siach
8c1ce928f4 arm: mvebu: clearfog: update SPI flash DT description
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.

Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.

Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Jon Nettleton
78aa018f07 arm: mvebu: Add board_setup for xhci hardware
This fixes the USB 3.0 support for the a38x SOC.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Prabhakar Kushwaha
f53e12d80a driver: net: fsl-mc: Use base 16 in simple_strtoul
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:53:15 -08:00
Ashish Kumar
91fded6200 armv8: ls1088aqds: Add SD boot support for ls1088qds
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:52:19 -08:00
Ashish Kumar
099f4093a5 armv8: ls1088ardb: Add SD boot support for ls1088
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:51:46 -08:00
Ashish Kumar
f65425fb46 armv8: ls1088: Enable SATA for ls1088
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:50:54 -08:00
Marek Vasut
2bfd43e550 ARM: rmobile: Fix eMMC signal voltage on Salvator-X/XS
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-12 16:17:31 -05:00
Tom Rini
3c674b7e87 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-11-09 08:11:30 -05:00
Lukasz Majewski
9c8979cdb7 imx7: Add include guards for include/asm/arch-mx7/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
e895e996ab imx5: Add include guards for include/asm/arch-mx5/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
90d0e38c1e imx6: Add include guards for include/asm/arch-mx6/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
a3eec24ad3 imx:display5: Add support for LWN's DISPLAY5 board
This commit provides support for LWN's IMX6Q based DISPLAY5 board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
ec1b26973c imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCs
This commit provides generic function to set the RGMII/HSIC IO voltage
level on iMX6 devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Fabio Estevam
b2e6ad451b mx51: Select the ESDHC_A001 erratum
When a high speed card is connected to mx51evk the following error is seen:

U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)

CPU:   Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC
Hit any key to stop autoboot:  0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed

The root cause for the failure is the eSDHC-A001 erratum:

"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf

Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.

The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.

Successfully tested with a high speed SD card on a mx51evk board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
2017-11-07 10:13:11 +01:00
Fabio Estevam
5d09c27138 mx25: Select the ESDHC_A001 erratum
When a high speed card is connected to mx25 the following error is seen:

U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C:   ready
DRAM:  64 MiB
No arch specific invalidate_icache_all available!
MMC:   FSL_SDHC: 0
*** Warning - read failed, using default environment
In:    serial
Out:   serial
Err:   serial
Net:   FEC
Hit any key to stop autoboot:  0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed

, which prevents any usage of the SD card.

The root cause for the failure is the eSDHC-A001 erratum:

"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf

Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.

Successfully tested with a high speed SD card on a mx25pdk board.

Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
2017-11-07 10:13:00 +01:00
Fabio Estevam
07df697e14 mx25: Move MX25 selection to Kconfig
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07 10:12:50 +01:00
Klaus Goger
4f70039b36 rockchip: dts: rk3399: change sd-card io voltage to 3.0V
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Klaus Goger
366812fa26 rockchip: dts: Use defines for pin names in rk3399-puma.dtsi and rk3368-lion.dts
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
b1e1ce2cd4 rockchip: dts: rk3399-puma: update USB configuration
This change updates the USB configuration for the RK3399-Q7 in the DTS:
 * fixes the OTG board configuration by enabling it ('okay')
 * improves the speed of 'usb start' by disabling the unused EHCI/OHCI
   controllers

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
f2a9513168 rockchip: dts: rk3399-puma: update usbhub_enable regulator
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
 * the GPIO polarity is GPIO_ACTIVE_LOW
 * should be set to inactive (enable-active-low) when boot-on settings
   are applied
 * it can be changed at runtime (i.e. remove the always-on)

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
df1e6212f9 rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLE
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.

This fixes the mix-up and models it correctly:
 * the GPIO is low-active
 * the regulator should be enabled (enable-active-high) during
   boot-on initialisation

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:56 +01:00
Chris Brandt
fc85605018 cosmetic: rmobile: renesas spelled wrong
Renesas was spelled wrong.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
2017-11-06 09:59:03 -05:00
Patrice Chotard
e36591c350 spear: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for SPEAR
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
1537d38619 stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
fb48bc448c sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Dongjin Kim
568197fa03 ARM: dts: exynos: fix property values of LDO15/17 for ODROID-XU3/4
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-11-06 16:59:32 +09:00
Kever Yang
36de37f5ca rockchip: rk3328: fix rockchip_get_cru api
The API for get priv pointer is wrong, fix it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-01 11:21:32 +01:00
Fabio Estevam
e1f0715f64 wandboard: Add support for the MX6QP variant
Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-31 11:01:38 +01:00
Tom Rini
2d5e6b4aac Merge git://git.denx.de/u-boot-video 2017-10-29 10:11:08 -04:00
Tom Rini
bb3d9ed3a9 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-27 21:59:10 -04:00
Sumit Garg
9b3f40ad09 armv8: sec_firmware: Add support for loadables in FIT
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.

Brief description of implementation:
  Add two more address pointers (loadable_h, loadable_l) as arguments to
  sec_firmware_init() api.
  Create new api: sec_firmware_checks_copy_loadable() to check if loadables
  node is present in SEC firmware FIT image. If present, verify loadable
  image and copies it to secure DDR memory.
  Populate address pointers with secure DDR memory addresses where loadable
  is copied.

Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Sumit Garg
9781d9ff5f armv8: layerscape: Allocate 66 MB DDR for secure memory
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Ran Wang
d4c746c7b1 armv8: ls1088ardb: Enable USB command RDB qspi-boot
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:06 -07:00
Ran Wang
4417e83495 arm64: layerscape: Move CONFIG_HAS_FSL_XHCI_USB to Kconfig
Use Kconfig to select QE-HDLC and USB pin-mux.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:43:57 -07:00
Vasily Khoruzhick
1d7eef3f3f sunxi: video: add LCD support to DE2 driver
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-10-27 09:44:48 +02:00
Vasily Khoruzhick
79f285ddeb sunxi: video: split out PLL configuration code
It will be reused in new DM LCD driver.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2017-10-27 09:39:19 +02:00
Icenowy Zheng
be5b96f0e4 sunxi: setup simplefb for Allwinner DE2
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.

Add code to setup simplefb for Allwinner DE2 driver.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-26 11:57:14 +02:00
Icenowy Zheng
f6bdddc92b video: add an option for video simplefb via DT
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.

Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-26 11:53:39 +02:00
Icenowy Zheng
401a3ca0fb sunxi: change the DE1 video option to CONFIG_VIDEO_SUNXI
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.

Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2017-10-26 11:48:49 +02:00
Maxime Ripard
819f1e081c sunxi: binman: Add U-Boot binary size check
The U-Boot binary may trip over its actual allocated size in the storage.
In such a case, the environment will not be readable anymore (because
corrupted when the new image was flashed), and any attempt at using saveenv
to reconstruct the environment will result in a corrupted U-Boot binary.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Maxime Ripard
ce2e44d836 sunxi: Enable THUMB build for the U-Boot binary
We start to get to the limit of our main U-Boot binary size (with some
boards even crossing it). Enable its build using thumb2 to get some extra
room.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Maxime Ripard
7514069aa3 sunxi: Add support for the Banana Pi M2-Magic
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Quentin Schulz
c96f598be7 sunxi: clk: fix N formula for CPUX clocks
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).

This results in a clock set to a frequency that isn't specified as
possible for CPUs.

Let's use the correct formula.

Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-25 10:05:05 +02:00
Masahiro Yamada
624c0954c7 ARM: uniphier: use pr_*() more where appropriate
Commit dd74b945af ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:09:22 +09:00
Masahiro Yamada
272874879b ARM: dts: uniphier: sync DT with Linux 4.14-rc5
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Masahiro Yamada
9ac0e7b37a ARM: uniphier: split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL.  So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.

Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.

Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-23 01:02:05 +09:00
Masahiro Yamada
d0df9588e8 ARM: uniphier: remove CONFIG_UNIPHIER_ETH
The option is never enabled by anyone.  Remove the code surrounded
by its ifdef.  This should be handled by the clock/reset drivers.

CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Adam Ford
0a9ef45158 Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 16:44:07 -04:00
Praneeth Bajjuri
9b46ce8cfc arm: dra76: fastboot: extend cpu type for getvar command
'commit fa24eca1f2 ("omap: Add routine for setting fastboot variables")'
adds initial support and usage of "fastboot getvar" command
for DRA75x and DRA72x devices.

and
'commit 0f9e6aee9d ("arm: dra76: Add support for ES1.0 detection")'
adds initial dra76 device definition

This patch is to extend usage of "fastboot getvar" for DRA76 device.

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Vishal Mahaveer
b6df93598c omap-common: fastboot: extend cpu type for DRA71x rev 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Extend support for this
revision in "getvar cpu" command.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
[praneeth@ti.com: rebase to u-boot master]
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Tuomas Tynkkynen
c68c03f52b Drop CONFIG_HAS_DATAFLASH
Last user of this option went away in commit:

fdc7718999 ("board: usb_a9263: Update to support DT and DM")

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-16 09:42:51 -04:00
Alexander Graf
409f05f259 fdt: update bcm283x device tree sources to Linux 4.14 state
Upstream Linux has received a few device tree updates to the RPi
which we should propagate into the builtin U-Boot one as well to
gain hardware support.

This patch bumps the dts files to their 4.14 Linux counterparts
with the exception of sdhost on 32bit RPi versions. There we stay
with iproc as the sdhost driver is missing in U-Boot.

Signed-off-by: Alexander Graf <agraf@suse.de>
2017-10-16 09:42:51 -04:00
Masahiro Yamada
c7372d61fd ARM: uniphier: adjust ifdefs for new UniPhier DWC3 CONFIG
Now USB 3.0 feature is enabled/disabled by CONFIG_USB_DWC3_UNIPHIER.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Masahiro Yamada
5e5edca27c ARM: uniphier: change the default of SoC select to UNIPHIER_V7_MULTI
ARCH_UNIPHIER_V8_MULTI depends on !SPL, so the default may be hidden.
Use a clearer default.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Masahiro Yamada
dd74b945af ARM: uniphier: use pr_() instead of printf() where appropriate
Replace printf() with pr_() to specify proper loglevel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:24 +09:00
Masahiro Yamada
0f72b74b32 ARM: dts: uniphier: update GPIO nodes
Switch to the single node design.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:24 +09:00
Tom Rini
26f9184e09 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-12 13:36:58 -04:00
Marek Vasut
0a333602df ARM: imx6: Add DHCOM i.MX6 PDK board support
Add support for the DHCOM i.MX6 PDK board. This board has:
- FEC ethernet
- EHCI USB host
- 3x SDMMC

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-10-12 18:01:06 +02:00
Diego Dorta
e2000731ae mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functions
When compiling with W=1 errors are observed:

drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)

drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)

Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:18 +02:00
Diego Dorta
342b4b09b1 mx6: clock: Add a prototype for do_mx6_showclocks()
When compiling with W=1 the following warning is observed:

arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])

Remove this warning by adding the function prototype into arch-mx6/clock.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:01 +02:00
Ilya Ledvich
6963204c4c arm: imx7d: add support for Compulab cl-som-imx7
Add initial support for Compulab cl-som-imx7 SoM.
The initial support includes:
 - MMC
 - eMMC
 - SPI flash
 - I2C
 - FEC
 - USB
 - Serial console

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
2017-10-12 17:31:16 +02:00