Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Signed-off-by: Adam Ford <aford173@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
The bulk of these changes are an effort to unify Tegra186 builds with
builds of prior 64-bit Tegra generations. On top of that there are
various improvements that allow data (such as the MAC address and boot
arguments) to be passed through from early firmware to the kernel on
boot.
Called to configure Ethernet PHY interface selection and
configure clock selection in RCC Ethernet clock tree.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Add 2 new checks:
- detect when USB TYPE-C cable is not plugged correctly.
In this case, GND and VBUS pins are connected but not CC1
and CC2 pins.
- detect is an USB Type-C charger supplies more than 3 Amps
which is not compliant with the USB Type-C specification
In these 2 situations, stop the boot process and let red led
blinks forever.
V cc1 | V cc2 | power supply | red led | console message
range (Volts) |range (Volts)| (Amps) | blinks |
--------------|-------------|--------------|---------|-----------------------------------
> 2.15 | < 0.2 | > 3 | for ever| USB TYPE-C charger not compliant with specification
[2.15 - 1.23[ | < 0.2 | 3 | NO | NO
[1.23 - 0.66[ | < 0.2 | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | < 0.2 | 0.5 | 2 times | WARNING 500mA power supply detected
< 0.2 | < 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
> 0.2 | > 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update env_get_location() to be able to save environment into
NOR (SPI_FLASH).
Series-cc: pde, cke, pch, uboot-stm32
Cover-letter:
Add saveenv support for STM32MP1
This series adds saveenv support for STM32MP1 on several boot
devices. STM32MP1 is able to boot on eMMC, sdcard and NOR
(NAND support is not fully supported).
On eMMC and sdcard, environment is saved in EXT4 partition
On NOR, environment is saved in a dedicated partition
On NAND, environment is saved in a UBI volume.
This series:
- enables NAND and NOR support on ev1 board
- enables ENV_IS_IN_SPI_FLASH, ENV_IS_IN_UBI, ENV_IS_IN_EXT4
flags
- fixes get_mtdparts()
- allows to override interface, device and partition for ext4
environment
- updates rule to set ENV_IS_NOWHERE value
- introduce ENV_IS_IN_DEVICE
END
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of several environment location support, env_get_location
is needed to select the correct location depending of the boot
device .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to :
- select the current device to save the environment file
- select the correct EXT4 boot device instance
and partition to save the environment file.
For EXT4, device is mmc, device instance is 0 for sdcard or 1 for eMMC.
The partition is set to "auto" to select the first partition with
bootable flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch configure the default value for mtdids and mtparts
dynamically according the presence of nor and nand in
the board device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit 21af33ed03 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Puma SoMs have a 4 MB SPI NOR flash.
Therefore we can move the environment to the end of the flash
(4 MiB - 16 kiB) in order to not overlap with SPL.
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a short note about how to boot U-Boot on Nyan-big using tegrarcm.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pull DRAM layout configuration code into rcar-common.c instead of
having it in multiple copies across board files. This poses no
change for Salvator-X/XS, ULCB and Ebisu boards, however it adds
a bit of extra code for Draak and Eagle boards, which now gain
the capability of being passed in the DRAM layout by the ATF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Replace the boolean parameter of io_check_status that controls whether
the status is printed or not with a documenting enum.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
More recent versions of IHS FPGAs feature a different memory layout.
Add a Kconfig option to differentiate between the legacy layout, and the
new layout (which is used on the upcoming "Gazerbeam" and later boards).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Future gdsys boards will switch from the legacy drivers in board/gdsys/common
to DM-based drivers.
Define a Kconfig option that disables the legacy drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The "manual" RAM configuration should not be used if the DM RAM driver
is active, hence, disable the code if the CONFIG_MPC83XX_SDRAM config
variable is defined.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Move CONFIG_SYS_FPGA0_BASE, CONFIG_SYS_FPGA0_SIZE, CONFIG_SYS_FPGA1_BASE, and
CONFIG_SYS_FPGA1_SIZE to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since the gpio output status on MPC8xxx cannot be read back, it has to
be buffered locally.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The ppc4xx architecture was removed, and with it several old gdsys 44x
boards, but some "debris" from these purged boards was left over.
This patch removes these remnants (mostly entries in Makefiles, some now
superfluous data structures and some now obsolete config variables from
the whitelist).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The initialization sequence in the newest release notes of the 88e1518
phy omits two commands.
Remove them from the sequence.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
For the DM case, use the proper parameter for the regmap_init_mem call
(which is the ofnode, not the udevice).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value
of either 0x00040000 or 0x00000000.
CONFIG_SYS_LBC_MRTPR always has the value 0x20000000.
CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board.
CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000).
To simplify the configuration files, hardcode the setting of these
values for mpc83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same
value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We want to normalize all BR/OR config lines as much as possible.
The TQM834x board uses CONFIG_SYS_OR_TIMING_FLASH in a OR definition,
which we want to remove. But CONFIG_SYS_OR_TIMING_FLASH is also used
outside of the config file.
Replace these usages with the definition of the variable, so we can
remove the variable in the next patch.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.
To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config files
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx include files contain some settings of the PCI subsystem.
Migrate these to Kconfig until a proper DM PCI driver exists.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC8349ITX Kconfig option to replace the
CONFIG_MPC8349ITX ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC832XEMDS Kconfig option to replace the
CONFIG_MPC832XEMDS ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC8349EMDS config file contains config options to enable SDRAM
support. To keep this ability after the Kconfig migration, create a new
MPC8349EMDS_SDRAM board that enables the SDRAM support and remove the
SDRAM support from the original board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC8313ERDB has the option of either enabling NOR or NAND boot in its
config file (by commenting out certain #ifdefs). To keep this ability
after migrating options to Kconfig, we introduce two MPC8313ERDB
configs: one for NOR, and one for NAND.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmeter1, and kmcoge5ne boards also build from the same config
file with #ifdef logic.
Create a separate include config for each board with the #ifdef logic
resolved as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmsupx5, tuge1, kmopti2, and kmtepr2 boards all build from the same
include config file with lots of #ifdef logic.
To ease Kconfig migration, create new config include files for these
boards, and resolve the #ifdef logic as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.
The Kconfig migation will become easier if we get rid of these #ifdefs
first.
Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There are several includes in mx53cx9020.c which are not required
anymore.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
These mmc functions were not used anymore since DM_MMC was introduced.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Enable DM_VIDEO in config and don't overwrite console so it can be set
from environment
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Switch to DM_GPIO and add gpio_request where necessary.
This is needed for DM_VIDEO and fixes an issue with sd card detection
which was introduced by the combination of these commits:
commit 7a0425dd96 ("mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops")
commit 7e04b4c751 ("dm: arm: imx: migrate cx9020 to CONFIG_DM_MMC")
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
When using DM_I2C the speed value supplied to setup_i2c() is not used,
so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to
compile, but did not actually use them.
Change this so we no longer need to define an unused macro to compile in
DM_I2C mode. Also make it more clear that they do not control the bus
speed. Otherwise it is quite easy to mistakenly believe they are used
to set the bus speed.
Cc: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Enable the green led on SPL completion.
Red led has no pulldown and it will be lighted by default when the
board starts up.
If the PMIC is not configured to enable LDO2, the leds will not light.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The 2 CAN transceivers have a STBDY pin which must be low in order to
operate.
This pin is tied to PB25.
Set it to 0 in bootstrap.
At a later time, this needs to be controlled by Linux power management
system, or requested by some driver as a gpio and tied to 0 during
CAN link up.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Some periphs on the board need to be reset by holding their reset GPIO down
for a specific time period.
On a warm reset, the periphs are not being reset by any reset pin and may be
in a wrong state.
Reset them in the SPL to make sure we are booting into the correct state
machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth,
Ethercat)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Mark Jonas <mark.jonas@de.bosch.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of
CONFIG_OF_BOARD.
Also remove unused code about prior_stage_fdt_address.
And modify CONFIG_SYS_FDT_BASE as flash address.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Add two defconfigs to support AE350 SMP booting from flash.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address
in S-mode whereas for 64bit system it will jump to 0x80200000 address
in S-mode.
Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both
32bit and 64bit system. This breaks S-mode U-Boot for 32bit system.
This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so
that S-mode U-Boot works fine for both.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Karsten Merker <merker@debian.org>
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add a version of samus which supports booting from TPL to SPL and then
to U-Boot. This allows TPL to select from an A or B SPL to support
verified boot with field upgrade.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Update the README to use the correct defconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Drop Toradex ARM Support <support.arm@toradex.com> from maintainer email
list as this just clogs our support ticketing system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----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=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Parse this device tree and
extract DRAM size information from it. This is useful on systems where
the DRAM size can vary between configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
In commit ad6054f1fe where support for the
Sancloud BeagleBone Enhanced (BBE) was added, new conditional
configuration of either MII pin muxing or RGMII pin muxing is done
depending on the board type. However, the old call to set up MII pin
muxing was not removed.
This may result in misconfiguration of the pin muxing for the BBE or
duplicate configuration for other boards and so we remove this obsolete
call.
Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The regdomain environment variable is set according to value read from
EEPROM. This has to be done in board_late_init, after the environment
variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
for the Turris Omnia target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since board watchdog is now unified and not handled in board files,
remove the unnecessary includes.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Unify the way how Omnia and Mox print board information (RAM size and
serial number).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Refactor RAM size reading from EEPROM in preparation for next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>