This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Fix copy-paste error of the I2C5 bus recovery GPIO assignment,
the I2C5 GPIOs are on gpio3 instead of gpio5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
The ECSPI1 is on I2C1/I2C2 pins of the SoC, update the pinmux accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Rename imx8mp-dhcom-pdk2-u-boot.dtsi to imx8mp-dhcom-u-boot.dtsi, since
this file is shared by PDK2, PicoITX and DRC02. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Add information about which exact SoM variant is used on which PDK2 variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Adam Ford <aford173@gmail.com>
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
* Remove unnecessary device tree nodes which are not needed in
U-Boot directly.
* Move all U-Boot specific device tree properties to u-boot dtsi.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 6337d53fdf ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs
the am335x device tree with the latest linux kernel am335x device tree.
That causes problems with device tree in SPL stage.
To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the
synced bus addresses correctly.
A custom U-Boot device tree is also needed since the SPL build removes
bus properties from bus nodes which are not explicitly marked with the
u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of
the in the SPL needed devices must be marked with u-boot,dm-pre-reloc.
Also since there is no driver for "ti,sysc" compatible property in SPL
the buses marked with this compatible string must also be marked with
compatible = "simple-bus" to make the underlying devices visible in
SPL. Otherwise the matching device drivers aren't found and the uclass
drivers are dropped.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ
calculation. This property configure correct value for SOF/ITP counter
and period of ref_clk.
This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/417545b948ea12a9301a5e80851f98523be2b443.1661259809.git.michal.simek@amd.com
Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Removes hwlocks properties from stm32mp151 pinctrl node. These locks
could be used for other purpose, depending on board and software
configuration hence do not enforce their use to protect pinctrl
devices.
This patch is an alignment with Linux device tree with v6.0 as the
hwsem support wasn’t yet added in pincontrol in kernel. It avoids
issues when the Linux kernel is started with the U-Boot device tree.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit ef4ce6df32 "video: stm32: stm32_ltdc: fix data enable polarity"
The panel display output wasn't functional anymore.
Device tree display-timings de-active property value must be updated
to 1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This new image is similar to u-boot-rockchip.bin except that it's
destined to be flashed on SPI-NOR flashes.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prepares for the creation of a u-boot-rockchip-spi.bin image
similar to u-boot-rockchip.bin to the exception it's destined for
SPI-NOR flashes instead of MMC storage medium.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
idbloader.img content - currently created by way of Makefile - can be
created by binman directly.
So let's do that for Rockchip ARM platforms.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot_devices constants for rk3288 were changed to match the
binding, but the dtsi file was not synced.
Fix by renaming the rk3288 mmc node names.
Also correct the clock name for "ciu-drive".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the Generic Names Recommendation in the Devicetree
Specification Release v0.3, and the DT Bindings for the Renesas Reduced
Pin Count Interface, the node name for a Renesas RPC-IF device should be
"spi". Especially on R-Car Gen3 and RZ/G2, the node name matters, as
the node is enabled by passing a DT fragment from TF-A to U-Boot, and
from U-Boot to subsequent software.
Fix this by renaming the device nodes from "rpc" to "spi".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
pcm051_rev3_defconfig config (Phytec Wega board) has been dropped in
64efd11d ("arm: Remove pcm051 board")
due to expired migration deadlines. Here, pcm051_rev3_defconfig support is
reintroduced.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
caam driver model enabled in spl for secure boot.
fsl_rsa_mod_exp driver enabled in spl for validating uboot image.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Replace code that accessed the GPIO registers directly with code that
makes use of the LED_GPIO driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-38x-controlcenterdc-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-xp-theadorable-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Replace it by including of mvebu-u-boot.dtsi file. When board does not use
-u-boot.dtsi then mvebu-u-boot.dtsi is included automatically by makefile
scripts/Makefile.lib.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Set u-boot,dm-pre-reloc for /soc/, /soc/internal-regs/ and &uart0 nodes as
it is required on every 32-bit Armada SoCs. And set also u-boot,dm-pre-reloc
for &spi0 when going to boot from SPI because otherwise SPL SPI drivers do
not load.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
64-bit Armada DTS files are not build correctly during compilation of
32-bit Armada boards and vice versa. So fix makefile build system to
compile only those dts files which are compatible for the current build
(64-bit Armada DTS files only for 64-bit builds and 32-bit Armada DTS files
only for 32-bit builds).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
UniPhier LD20, PXs2 and PXs3 boards have ethernet phy that has RX/TX delays
of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
So should set the phy-mode to "rgmii-id" to show that RX/TX delays are
enabled.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Signed-off-by: Marek Behún <kabel@kernel.org>
* Add SPDX-License-Identifier
* Add SFP and LED nodes
* Fix PHY nad NOR nodes
* Remove duplicates from u-boot.dtsi file
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows U-Boot mvebu-gpio.c driver to switch particular MPP pin into
GPIO mode and enable GPIO support.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Qualcomm device trees in U-Boot are currently not consistent with
the upstream DTs used in the Linux kernel. While some bindings are
similar to the official specification in the Linux kernel, several
nodes have subtle differences, e.g. the "compatible"s or the exact
specification of memory registers.
This means that some of the Qualcomm-related U-Boot drivers are not
compatible with the Linux DT (and vice versa).
The SPMI node is one such example: the "core" region starts at
0x0200f000 in the upstream Linux MSM8916 DT, but in U-Boot it starts at
0x0200f800. The end result is normally the same, since the Linux SPMI
driver simply adds the 0x800 internally.
However, commit f5a2d6b4b0 ("spmi: msm: add arbiter version 5
support") imported this behavior into the U-Boot driver, without
adjusting the DB410c/DB820c device trees. This means that the 0x800
offset is now added twice, breaking all SPMI read/write operations:
Failed to find PMIC pon node. Check device tree
Failed to find pm8916_gpios@c000 node.
USB init failed: -6
starting USB...
Bus ehci@78d9000: Failed to find pm8916_gpios@c000 node.
probe failed, error -6
No working controllers found
While the mistake is strictly speaking in the spmi-msm driver, fix the
issue by making the SPMI nodes in the DB410c/DB820c consistent with the
upstream Linux DT instead.
Ideally we should even go a step further by fixing the remaining uses
of custom bindings in the U-Boot drivers and moving to using the Linux
DTs as-is. This would likely avoid such mistakes in the future and
would also make the porting process much easier.
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Fixes: f5a2d6b4b0 ("spmi: msm: add arbiter version 5 support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Currently u-boot running on mt7622 will print an warning log at beginning:
> serial_mtk serial@11002000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
It turns out that the pinctrl uclass can't work properly in board_f stage.
Since the uart0 is the default UART device used by bootrom, and will be
initialized in both bootrom and tf-a bl2. It's ok not to setup pinctrl for
uart0 in u-boot.
This patch removes the default pinctrl of uart0 to suppress the unwanted
warning.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The entry for DDRSS_PI_321_DATA was accidentally repeated leading to the
last few PI registers being incorrectly programmed.
Fix this.
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Configure debug UART pins as function: "qup9" rather than being regular
gpios. It fixes a hang seen during pinmux setting.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than using magic numbers as clock ids for peripherals import
qcom,gcc-sdm845.h from Linux to be used standard macros for clock ids.
So start using corresponding clk-id macro for debug UART.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
According to u-boot DT recomendation, u-boot specific DT properties belong
to *-uboot.dtsi. Also for starqltechn board (which is the only current
consumer of sdm845.dtsi), the properties are already included in
starqltechn-uboot.dtsi, so remove corresponding redundant properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently there is a mismatch among DT node overrides in starqltechn
board DTS file and the actual DT nodes in the sdm845.dtsi. So fix that
to align with DT nodes in sdm845.dtsi.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@0:pwms: property size (12) too small for cell size 3
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@1:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb).
Please further note that the PMIC node name got changed from a pmic
label to pmic@25 which required adjustment in resp. board SPL file
board/toradex/verdin-imx8mm/spl.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the pinctrl_pmic reference which does not
exist in the Linux upistream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx8mm-venice-gw700x-u-boot.dtsi:26.1-14 Label or
path pinctrl_pmic not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
vf610-colibri-eval-v3.dtb rather than the previous vf610-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the included SoC dtsi from vf.dtsi to
vf610.dtsi as this is how it is named in Linux upstream.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx7d-colibri-eval-v3.dtb rather than the previous
imx7-colibri-rawnand.dtb and imx7d-colibri-emmc-eval-v3.dtb rather than
the previous imx7-colibri-emmc.dtb).
Please further note that the PMIC node name got changed from rn5t567@33
to pmic@33 which required adjustment in resp. board file
board/toradex/colibri_imx7/colibri_imx7.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the epdc reference which does not exist in
the Linux upstream device tree and rename the qspi1 reference to qspi as
this is how it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:10.1-6 Label or path
epdc not found
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:29.1-7 Label or path
qspi1 not found
+Error: arch/arm/dts/imx7d-sdb-qspi-u-boot.dtsi:6.1-7 Label or path
qspi1 not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the qspi1 reference to qspi as this is how
it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7-cm.dtb.pre.tmp:96.1-7 Label or path qspi1 not
found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx6ull-colibri-eval-v3.dtb rather than the previous imx6ull-colibri.dtb
and imx6ull-colibri-emmc-eval-v3.dtb rather than the previous
imx6ull-colibri-emmc.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the qspi node with its flash0 label as this
is already in the Linux upstream device tree.
This avoids the following error once synchronised:
+arch/arm/dts/imx6ul-14x14-evk.dtb: ERROR (duplicate_label):
/soc/bus@2100000/spi@21e0000/n25q256a@0: Duplicate label 'flash0' on
/soc/bus@2100000/spi@21e0000/n25q256a@0 and
/soc/bus@2100000/spi@21e0000/flash@0
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
imx6dl-colibri-eval-v3.dtb rather than the previous imx6-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next 20220706.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Apalis Evaluation (carrier) board (e.g.
imx6q-apalis-eval.dtb rather than the previous imx6-apalis.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step make sure to refer to absolute node paths where
labels were removed in Linux upstream.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:3.1-7 Label or path aips1
not found
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:11.1-5 Label or path soc
not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warning:
w+arch/arm/dts/imx6dl-brppt2.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add definition for FSPI configuration block and subsequently new offsets for
u-boot-spl and u-boot-itb for CONFIG_FSPI_HEADER option.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- leave tx-delay/rx-delay undefined in dt defaulting to 2.0ns
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
PA13 and PA14 are used for USB power control and can't be used
to enforce fastboot or stm32prog mode by pressing a button.
Defining CONFIG_FASTBOOT/CONFIG_CMD_STM32PROG without this patch applied
results in fastboot/stm32prog always starting, because PA13/PA14 are always
low during boot. So drop the wrong trigger gpios definitions.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Activate the led managed in stm32mp1 board for U-Boot indication
in STM32MP13F-DK device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for SCMI firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for OP-TEE firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The EVB has an EEPROM on bus 3 and a LM75 temp sensor on bus 7. Enable
those busses we can test the I2C driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The same as the upstream Linux device tree, each i2c bus has a property
specifying the reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set the pinctrl groups for each I2C bus. These are essential to
I2C operating correctly.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add devicetrees for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add handoff headers for the Google Chameleonv3 variants: 480-2 and
270-3. Both files were generated using qts-filter-a10.sh.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
Sync the pinebook pro to upstream 5.18, in particular this brings
brings in a fix so the DP is disabled so Linux will actually boot.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move the dma-controller nodes
to the DT root.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version sort the mipi,hdmi,lvds and dp nodes.
Changed:
Rename mipi_dsi label.
Rename dp nodename.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The memory on this board is microchip 24aa025e48 which is compatible with
at24c02 with a page size of 16.
Fix the compatible accordingly.
Reported-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
microchip,24aa025e48 does not exist in the bindings of this driver.
It can be replaced with atmel,at24c02 which is a standard compatible
and the memory is compatible with this one, depending on the page size.
microchip 24aa02e48 has a page size of 8, while 24aa025e48 has a page
size of 16 bytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change the compatible of the qspi child node to
`jedec,spi-nor` so that it can be properly found
when probing the bus.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
The previous version of this change was only partially applied.
Fixes: 4746694cba ("ARM: dts: sun4i: Sync from Linux v5.18-rc1")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
"size-cells" of the nand controller node should be 0 as the "reg"
property of the nand device node contains the chip select number and not
address information.
The patch fixes the below compilation warning
arch/arm/dts/zynq-zc770-xm011.dtb: Warning (reg_format):
/axi/memory-controller@e000e000/nand-controller@0,0/nand@0:reg: property
has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6e90665a2dad7fe8ade10b8f57101f8144963791.1655288559.git.michal.simek@amd.com
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb gorup pins.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b245c165f05845c1f3ab41a92c82b7ec1538cee4.1655288171.git.michal.simek@amd.com
Board is using kv260 design for couple of parts defined by spec like i2c
eeproms, ina260, uart, etc.
Board has 4 gems. One gem connected via PS SGMII(GT), another PS RGMII(MIO)
and 2 via EMIO. First two shares the same MIO lines for PHYs. PL based one
have separate EMIO lines via PL.
Also two USB 3.0 with usb hubs are present. USB phys and USB hubs should
have separate reset line. The first usb0 hub also has USB-SD controller
(usb2244) connected to port 0.
To test compatibility with k26 you can run:
fdtoverlay -o /tmp/output.dtb -i arch/arm/dts/zynqmp-sm-k26-revA.dtb \
arch/arm/dts/zynqmp-sck-kr-g-revA.dtbo
Also add support for kr260-revB board. Based on FRU it is revision B
but schematics can be label as revA03.
Changes in revB are:
- SFP light
- GEM2/3 TX_CLK fixes
- PMOD/RPI connector fixes
- Replace si5332 with oscilators
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dac2ee1826e73b89c8cc1e430354eb43d291f675.1652870941.git.michal.simek@amd.com
This was previously needed, but U-Boot is now capable of parsing
the new "phy-connection-type" property that is already used in
the main devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This syncs the devicetree files with the latest Linux kernel (5.19-rc2).
This also fixes the currently broken ethernet support:
Before:
Net: Could not get PHY for FEC0: addr 0
After:
Net: eth0: ethernet@30be0000
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The HPE SoC is new to linux. A basic device tree layout with minimum
required for linux to boot including a timer and watchdog support has
been created.
The dts file is empty at this point but will be updated in subsequent
updates as board specific features are enabled.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Seems that u-boot can't probe i2c bus at 2.6Mhz speed, so lower
the speed to the default value 100Khz.
v2: fix i2c1 frequency in the root omap3-u-boot.dtsi include.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
This adds an SFP binding for the processors it is present on. I have
only tested this for the LS1046A.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
QorIQ platforms now use different clock bindings. Although we don't use
the device tree for clocks on this platform, it is helpful to sync it
because then the bindings will more closely match Linux. Additionally,
it allows for using more clock fractions (such as platform/4).
This corresponds to Linux commit b6f5e7019391 ("ARM: dts: ls1021a:
update the clockgen node").
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
This new MMC sample select value is obtained from running
tests on multiple Stratix 10 boards and proven working.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
