Commit graph

368 commits

Author SHA1 Message Date
Marek Vasut
4a9743f73c ARM: socfpga: Clear PL310 early in SPL
On SoCFPGA Gen5 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.

The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.

This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.

The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2019-02-25 16:07:36 +01:00
Marek Vasut
2c0b300bc3 ARM: socfpga: Configure PL310 latencies
Configure the PL310 tag and data latency registers, which slightly
improves performance and aligns the behavior with Linux.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2019-02-25 16:07:36 +01:00
Simon Goldschmidt
473f55676a arm: socfpga: gen5: remove hacked ETH RST handling
The 'dwmac_socfpga' ETH driver can now get the MACs out of reset
via the socfpga reset driver and can set PHY mode via syscon.

This means we can now remove the ad-hoc code to do this from
arch/arm/mach-socfpga.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-02-18 13:00:53 +01:00
Tien Fong Chee
f4b4092474 spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:14:21 -05:00
Tien Fong Chee
0c3a9ed409 spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:12:48 -05:00
Ang, Chee Hong
bd5581716d arm: socfpga: stratix10: Enable Stratix10 FPGA Reconfiguration
Select CONFIG_FPGA_STRATIX10 for CONFIG_TARGET_SOCFPGA_STRATIX10.

Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
2018-12-20 17:12:25 +01:00
Ang, Chee Hong
877ec6ebbd arm: socfpga: stratix10: Add Stratix10 FPGA into FPGA device table
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.

Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
2018-12-20 17:12:25 +01:00
Ang, Chee Hong
8b36ba27ad arm: socfpga: stratix10: Add macros for mailbox's arguments
Add macros for specifying number of arguments in mailbox command.

Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
2018-12-20 17:12:25 +01:00
Ang, Chee Hong
d99f1e92a2 arm: socfpga: stratix10: Add generic FPGA reconfig mailbox API for S10
Add a generic mailbox API for FPGA reconfig status which can be
called by others. This new function accepts 2 different mailbox
commands: CONFIG_STATUS or RECONFIG_STATUS.

Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
2018-12-20 17:12:25 +01:00
Simon Goldschmidt
30bade20a6 arm: socfpga: fix SPL booting from fpga OnChip RAM
This patch prevents disabling the FPGA bridges when
SPL or U-Boot is executed from FPGA onchip RAM.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Simon Goldschmidt
dd8ee8ea2a arm: socfpga: make config structs const
There are two config structs left in wrap_sdram_config.c that can
be made const.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Ooi, Joyce
8be11fb3c1 arm: socfpga: stratix10: add sgmii in phymode setup
Additional sgmii phymode is added in socfpga_phymode_setup() along with
a minor fix for maximum number of GMACs.

Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
2018-10-03 12:56:50 +02:00
Ley Foon Tan
74c78024a0 arm: socfpga: Remove unused function socfpga_emac_manage_reset()
Remove code from the reset manager that is never called.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-10-03 12:56:50 +02:00
Dalon Westergreen
02d8d32591 socfpga: stratix10: fix sdram_calculate_size
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2018-09-15 03:17:01 +02:00
Marek Vasut
331c372210 ARM: socfpga: Convert Arria10 to timer framework
Switch the Arria10 from ad-hoc hardcoded timer to timer framework
and the DW APB timer driver. This allows the A10 to extract timer
information, like timer rate, from clock framework and thus DT
instead of having it hardcoded in U-Boot configuration files.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:20 +02:00
Marek Vasut
0b8f6378cb ARM: socfpga: Reorder Arria10 SPL
The Arria10 SPL is a complete mess of calls to functions which are
called in the wrong context and it is surprise it works at all. This
patch tries to clean that mess up by shuffling the function calls
around and moving the calls into the correct context. Due to the
delicate nature of the reordering, this is done in one huge patch.

The following changes happen in this patch:
- Security policy init and NIC301 happens first in board_init_f()
- The clock init happens very early in board_init_f() in SPL only
- arch_early_init_r() only registers the FPGA, just like on Gen5
- arch_early_init_r() is never called from any _f() function
- Dedicated FPGA pins are inited in board_init_f() as on Gen5

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:20 +02:00
Ley Foon Tan
8497cb9b25 arm: socfpga: stratix10: Fix mailbox urgent command with urgent register
According to mailbox spec, software should send urgent command with
urgent register instead of COUT location. This patch write urgent
command index to urgent register.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:20 +02:00
Ley Foon Tan
db3b5e9898 arm: socfpga: stratix10: Enable EMAC to FPGA bridge based on handoff
Code checking and setting EMAC use fpga is in
populate_sysmgr_fpgaintf_module(). So, call to sysmgr_pinmux_init()
instead of populate_sysmgr_pinmux().
In sysmgr_pinmux_init(), it will call to both populate_sysmgr_pinmux()
and populate_sysmgr_fpgaintf_module().

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:20 +02:00
Ley Foon Tan
b0c0a715f9 arm: socfpga: Fix SYSMGR_FPGAINTF_EMACx bit mask
Bitmask for EMAC should be bit-0, EMAC1 bit-8 and EMAC2 bit-16.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-15 12:41:09 +02:00
Marek Vasut
d81b5da3fe ARM: socfpga: clk: Convert to clock framework
Use clock framework functions to fetch clock information now that there
is a clock driver for Arria10, instead of custom coded register parsing.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
f4c3e0dcf5 ARM: socfpga: clk: Drop unused variables on Arria10
The variables removed in this patch are never used, they are only ever
assigned and then waste precious memory. Drop both the assignment and
the variables.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
49e508e962 ARM: socfpga: clk: Make L4SP and MMC clock calculation Gen5 only
The L4SP and MMC clock precalculation is specific to Gen5, it is not
needed on Arria10/Stratix10. Isolate it to Gen5 until there is a proper
clock driver for Gen5, at which point this will go away completely.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
934aec71d6 ARM: socfpga: clk: Obtain handoff base clock via DM
Bind fixed clock driver to the base clock instantiated in the handoff
DT and use DM clock framework to get their clock rate. This replaces
the ad-hoc DT parsing present thus far.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
d6a61da462 ARM: socfpga: Remove adhoc ethernet reset and configuration
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
6385a8a964 ARM: socfpga: Zap unused reset code
Remove code from the reset manager that is never called.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
f9edeb32a9 ARM: socfpga: Zap all the UART handling complexity
The UART reset handling is now done via reset framework using the
SoCFPGA reset driver. The UART console assignment is done using the
DM and console framework. Nuke all this comlexity, since it is just
duplicating the same functionality, badly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-08-13 22:35:40 +02:00
Marek Vasut
fe88c2fea7 ARM: socfpga: Enable DM I2C framework on A10
Enable the DM I2C framework on Arria10, so that the DM capable
Designware I2C driver can handle the reset via DM reset framework.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:17 +02:00
Marek Vasut
8145c1c299 ARM: socfpga: Enable DM reset framework on A10
Enable the DM reset framework and DM reset driver on Arria10 both
in U-Boot and in SPL. This lets U-Boot parse reset control from DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:17 +02:00
Marek Vasut
af74658e04 ARM: socfpga: Register the FPGA on A10 in SPL again
The restructuring of the SPL dropped registration of the FPGA in SPL,
readd it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Fixes: c859f2a77d ("arm: socfpga: Restructure the SPL file")
2018-08-13 22:35:16 +02:00
Simon Goldschmidt
e4ff8420c5 arm: socfpga: gen5: combine some init code for SPL and U-Boot
Some of the code for low level system initialization in SPL's
board_init_f() and U-Boot's arch_early_init_r() is the same,
so let's combine it into a single function called from both.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-08-13 22:35:06 +02:00
Simon Goldschmidt
c0b4fc1a1b arm: socfpga: cyclone5: handle debug uart
If CONFIG_DEBUG_UART is enabled, correctly initialize
the debug uart before console is initialized to debug
early boot problems in SPL.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-08-13 15:29:54 +02:00
Simon Goldschmidt
20905f5fa6 arm: socfpga: spl_gen5: clean up malloc_base assignment
In spl_gen5's board_init_f(), gd->malloc_base is manually assigned
at the end of the function to point to sdram.  This code is outdated
as by now, the heap is switched to sdram by the common function
spl_relocate_stack_gd() if the appropriate defines are set.

As it was, the value assigned manually was directly overwritten by
this common code, so remove the manual assignment.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-08-13 15:29:54 +02:00
Simon Goldschmidt
40c36f8d49 arm: socfpga: fix SPL on gen5 after moving to DM serial
There were NULL pointers dereferenced because DM was used
too early without correct initialization:
- malloc_simple returned NULL when called from preloader_console_init()
  because gd->malloc_limit was 0
- uclass_add dereferenced gd->uclass_root members which were NULL because
  dm_init (or one of its relatives) has not been called.

All this is fixed by calling spl_early_init before calling
preloader_console_init.

This fixes commit 73172753f4 ("ARM: socfpga: Convert to DM serial")

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-08-13 15:29:54 +02:00
Michal Simek
58008cbab5 Kconfig: Sort bool, default, select and imply options
Another round of sorting Kconfig entries aplhabetically.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-30 07:18:48 -04:00
Marek Vasut
42f4b83b52 ARM: socfpga: Init missing security policies on A10
The Arria10 requires proper configuration of the NOC firewall, otherwise
the access to certain areas of the LWHPS bridge fails in Linux. Add the
missing setup.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-25 00:13:32 +02:00
Marek Vasut
937db7188e ARM: socfpga: Assure correct CPACR configuration
Make sure the ARM CPACR register is zeroed out, this is mandatory
on Arria10.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-25 00:13:32 +02:00
Siva Durga Prasad Paladugu
12308b128f lib: fdtdec: Rename routine fdtdec_setup_memory_size()
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-07-19 10:49:56 +02:00
Tom Rini
914bb7ea2f Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Update SPDX tag in arch/arm/mach-socfpga/spl_a10.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-13 14:47:04 -04:00
Ley Foon Tan
aa52966336 arm: socfpga: Fixes: include <debug_uart.h>
Fix compilation warning when enable CONFIG_DEBUG_UART.

arch/arm/mach-socfpga/spl_s10.c: In function ‘board_init_f’:
arch/arm/mach-socfpga/spl_s10.c:146:2: warning: implicit declaration of function ‘debug_uart_init’; did you mean ‘part_init’? [-Wimplicit-function-declaration]
  debug_uart_init();

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 16:03:35 +02:00
Ley Foon Tan
8c9f247a1a arm: socfpga: Fix: Compile MCR instruction on ARM 32-bit only
MCR instruction only available in ARM 32-bit. So, compile MCR instruction
when ARM 32-bit is enabled.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 16:03:35 +02:00
Marek Vasut
887a8b6ec2 ARM: socfpga: Assure correct ACTLR configuration
Make sure the ARM ACTLR register has correct configuration, otherwise
the Linux kernel refuses to boot. In particular, the "Write Full Line
of Zeroes" bit must be cleared.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-12 09:22:13 +02:00
Marek Vasut
297b653bbf ARM: socfpga: Pull DRAM size from DT
Pull the DRAM size from DT instead of hardcoding it into U-Boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-12 09:22:13 +02:00
Ley Foon Tan
2e1de5bd97 arm: socfpga: Add do_bridge_reset for Arria 10
Add do_bridge_reset() function for Arria 10, it is required by misc.c.

arch/arm/mach-socfpga/built-in.o: In function `do_bridge':
arch/arm/mach-socfpga/misc.c:221: undefined reference to `do_bridge_reset'
make[1]: *** [u-boot] Error 1

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
a684729a15 arm: socfpga: stratix10: Enable Stratix10 SoC build
Add build support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>

Conflicts:

	arch/arm/Kconfig
	arch/arm/mach-socfpga/Kconfig
2018-07-12 09:22:12 +02:00
Ley Foon Tan
0bc28b7cb8 ddr: altera: stratix10: Add DDR support for Stratix10 SoC
Add DDR support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
73aede596c arm: socfpga: stratix10: Add timer support for Stratix10 SoC
Add timer support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
4765ddb0da arm: socfpga: stratix10: Add SPL driver for Stratix10 SoC
Add SPL driver support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
c859f2a77d arm: socfpga: Restructure the SPL file
Restructure the SPL so each devices such as CV, A10 and S10
will have their own dedicated SPL file. SPL file determine
the HW initialization flow which is device specific

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
914a84e6ee arm: socfpga: stratix10: Add MMU support for Stratix10 SoC
Add MMU memory mapping table for Stratix SoC.

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
a280e9db64 arm: socfpga: stratix10: Add mailbox support for Stratix10 SoC
Add mailbox support for Stratix SoC

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
d559130e36 arm: socfpga: stratix10: Add misc support for Stratix10 SoC
Add misc support such as EMAC and cpu info printout for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
10f9e4b1c8 arm: socfpga: misc: Move bridge command to misc common
Move bridge command to misc common driver, in preparation to used by
other platforms.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:11 +02:00
Tom Rini
03b54997d5 board/aries: Remove
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them.  Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-02 15:52:50 -04:00
Tom Rini
624d2cae34 SPDX: Fixup SPDX tags in a few new files
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-20 09:47:45 -04:00
Ley Foon Tan
5fb033a336 arm: socfpga: misc: Add CONFIG_SYS_L2_PL310 switch
Preparation for Stratix 10 enablement. In ARM64, L2 cache controller is
accessed through processor registers. So, add CONFIG_SYS_L2_PL310 switch
conditional build in order this file can by shared across other SOCFPGAs.

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:48 +02:00
Ley Foon Tan
73175d04a9 arm: socfpga: stratix10: Add pinmux support for Stratix10 SoC
Add pinmux driver support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:48 +02:00
Ley Foon Tan
3607a8084a arm: socfpga: stratix10: Add reset manager driver for Stratix10 SoC
Add Reset Manager driver support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:47 +02:00
Ley Foon Tan
508791a035 arm: socfpga: stratix10: Add clock manager driver for Stratix10 SoC
Add Clock Manager driver support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:47 +02:00
Ley Foon Tan
641f7470b6 arm: socfpga: stratix10: Add watchdog and firewall base addresses
Add the base address for watchdog and firewall.

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:47 +02:00
Ben Kalo
4916388a39 ARM: socfpga: Fix Documentation errors in scu_registers
According to ARM Cortex-A9 MPCore TRM section 2.2 - SCU registers
Access Control register offset is 0x50.

Signed-off-by: Ben Kalo <ben.h.kalo@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
011fa5f33d ARM: socfpga: Adding SoCFPGA info for both SPL and U-Boot
SoC FPGA info is required in both SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
c960ef29cd ARM: socfpga: Adding clock frequency info for U-Boot
Clock frequency info is required in U-Boot because info would be erased
when transition from SPL to U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
901af3e903 configs: Add DDR Kconfig support for Arria 10
This patch enables DDR Kconfig support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
5658a299bd ARM: socfpga: Add DDR driver for Arria 10
Add DDR driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
53faef1e3f ARM: socfpga: Add DRAM bank size initialization function
Add function for both multiple DRAM bank and single DRAM bank size
initialization. This common functionality could be used by every single
SOCFPGA board.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18 10:30:47 +02:00
Tien Fong Chee
9ef9fe3455 ARM: socfpga: Rename the gen5 sdram driver to more specific name
Current sdram driver is only applied to gen5 device, hence it is better
to rename sdram driver to more specific name which is related to gen5
device.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2018-05-18 10:30:47 +02:00
Marek Vasut
32f99757f4 ARM: socfpga: Repair A10 EMAC reset handling
The EMAC reset and PHY mode configuration was never working on the
Arria10 SoC, fix this. This patch pulls out the common code into
misc.c and passes the SoC-specific function call in as a function
pointer.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Marek Vasut
480f7f9c3e ARM: socfpga: Sync A10 clock manager binding parser
The A10 clock manager parsed DT bindings generated by Quartus the
bsp-editor to configure the A10 clocks. Sadly, those DT bindings
changed at some point. The clock manager patch used the old ones,
this patch replaces the bindings parser with one for the new set.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Marek Vasut
48befc009f ARM: socfpga: Clean up Kconfig entries
Shuffle the default Kconfig entries around so it is not such a mess.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Marek Vasut
f79173280c ARM: socfpga: Zap CONFIG_SOCFPGA_VIRTUAL_TARGET
This was never used, is not used anywhere and is just in the way
by adding annoying ifdeffery. Get rid of it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18 10:30:46 +02:00
Tom Rini
3aba3fd654 Merge git://git.denx.de/u-boot-socfpga 2018-05-10 22:57:41 -04:00
Tom Rini
f739fcd831 SPDX: Convert a few files that were missed before
As part of the main conversion a few files were missed.  These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict.  This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.

Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:35 -04:00
Marek Vasut
34fc2a6edf ARM: socfpga: Add boot trampoline for Arria10
The Arria10 uses slightly different boot image header than the Gen5 SoCs,
in particular the header itself contains an offset from the start of the
header to which the Arria10 jumps. This offset must not be negative, yet
the header is placed at offset 0x40 of the bootable binary. Therefore, to
jump into U-Boot, add a trampoline just past the Arria10 boot header and
point to this trampoline at fixed offset from the header generated using
the mkimage -T socfpgaimage_v1 . Note that it is not needed to jump back
to offset 0x0 of the image, it is possible to jump directly at the reset
label and save processing two instructions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
2018-05-08 21:08:42 +02:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Chin Liang See
8faeab9304 arm: socfpga: stratix10: Add base address map for Statix10 SoC
Add the base address map for Stratix10 SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2018-04-17 11:39:48 +02:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Marek Vasut
7fb464302e ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 board
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.

Signed-off-by: Marek Vasut <marex@denx.de>
2018-02-26 14:06:02 +01:00
Lukasz Majewski
d695d66278 spl: eMMC/SD: Provide one __weak spl_boot_mode() function
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.

The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.

To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-07 22:06:18 -05:00
Tom Rini
ab12aa24e6 ARM: socfpga: Convert callers of cm_write_with_phase for wait_for_bit_le32
Now that we have and use wait_for_bit_le32() available, the callers of
cm_write_with_phase() should not be casting values to u32 and instead we
expect a const void *, so provide that directly.

Fixes: 48263504c8 ("wait_bit: use wait_for_bit_le32 and remove wait_for_bit")
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-26 13:08:03 -05:00
Tom Rini
1d12a7c8cd Merge git://git.denx.de/u-boot-spi 2018-01-26 07:46:34 -05:00
Eugeniy Paltsev
21143ce127 SOCFPGA: clock manager: implement dw_spi_get_clk function
Implement dw_spi_get_clk function to override its weak
implementation in designware_spi.c driver.

We need this change to get rid of cm_get_spi_controller_clk_hz
function and clock_manager.h include in designware_spi.c driver.

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-26 11:25:49 +05:30
Álvaro Fernández Rojas
48263504c8 wait_bit: use wait_for_bit_le32 and remove wait_for_bit
wait_for_bit callers use the 32 bit LE version

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:03:43 +05:30
Tom Rini
b4b9814f1c arm: socfpga: Guard commands with CONFIG_SPL_BUILD tests
In order for these commands to not be included in SPL we need to guard
compilation with CONFIG_SPL_BUILD checks.  Reorganize some sections of
code slightly in order to avoid new warnings and mark the command
functions as static as they should have been before.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-09 12:38:55 +01:00
Philipp Tomsich
a002077d7d socfpga: boot0 hook: adjust to unified boot0 semantics
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Masahiro Yamada
5e8c39d4f4 ARM: socfpga: fix duplicate const specifier warning
GCC 7.1 warns:
duplicate ‘const’ declaration specifier [-Wduplicate-decl-specifier]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-23 15:13:20 +02:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Tien Fong Chee
2baa997240 arm: socfpga: Add FPGA driver support for Arria 10
Add FPGA driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2017-07-26 10:31:44 +02:00
Tien Fong Chee
6867e19a43 arm: socfpga: Restructure FPGA driver in the preparation to support A10
Move FPGA driver which is Gen5 specific code into Gen5 driver file
and keeping common FPGA driver intact. All the changes are still keeping
in driver/fpga/ and no functional change. Subsequent patch would move
FPGA manager driver from arch/arm into driver/fpga/.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2017-07-26 10:31:44 +02:00
Tien Fong Chee
6a34af5b41 arm: socfpga: Remove unused passing parameter of socfpga_bridges_reset
Remove parameter from socfpga_bridges_reset(), and keeping this function
for single purpose which is just triggering reset on bridges.
socfpga_reset_deassert_bridges_handoff() can be called for releasing reset
on any bridges based on the bridge setting defined in fdt.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2017-07-26 10:31:43 +02:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Ley Foon Tan
d89e979c42 arm: socfpga: Enable build for Arria 10
Update Kconfig and Makefile to enable Arria 10.
Clean up Makefile and sorting *.o alphanumerically.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:19 +02:00
Ley Foon Tan
8f4c80c4fd arm: socfpga: Add SPL support for Arria 10
Add SPL support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
35b9800ff2 arm: socfpga: Add misc support for Arria 10
Add misc support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
caf36e1edb arm: socfpga: Add pinmux for Arria 10
Add pinmux support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
c887d48017 arm: socfpga: Add sdram header file for Arria 10
Add sdram header file for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
86f032e630 arm: socfpga: Add system manager for Arria 10
Add system manager register struct and macros for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
177ba1f927 arm: socfpga: Add clock driver for Arria 10
Add clock driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
827e6a7e0d arm: socfpga: Add reset driver support for Arria 10
Add reset driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
d83b8193ad arm: socfpga: Add A10 macros
Add i2c, timer and other A10 macros.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
d1c559af5f arm: socfpga: Restructure misc driver
Restructure misc driver in the preparation to support A10.
Move the Gen5 specific code to gen5 file.

Change all uint32_t_to u32.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
4ddd541d6c arm: socfpga: Restructure system manager
Restructure system manager in the preparation to support A10.
No functional change.

Change uint32_t to u32.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
2b09ea48dd arm: socfpga: Restructure reset manager driver
Restructure reset manager driver in the preparation to support A10.
Move the Gen5 specific code to gen5 files.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
de77811589 arm: socfpga: Restructure clock manager driver
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.

- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
  cm_write_with_phase() and cm_basic_init().

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:16 +02:00
Dalon Westergreen
6bd041f00d arm: socfpga: add cyclone5 based de10-nano board
Add support for the Terasic DE10-Nano board.  The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2017-04-25 12:46:44 +02:00
Ley Foon Tan
707cd012e2 arm: socfpga: Convert Altera DDR SDRAM driver to use Kconfig
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-04-14 14:06:57 +02:00
Marek Vasut
a548bc511f ARM: socfpga: Rename MCVEVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:44 +02:00
Chee, Tien Fong
4c0f3e7f7b ARM: socfpga: boot0 hook: remove macro from boot0 header file
Commit ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.

Fixes: ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file")

Signed-off-by: Chee, Tien Fong <tien.fong.chee@intel.com>
2017-04-14 14:06:42 +02:00
Dalon Westergreen
f0fb4fa7d5 SPL: add support to boot from a partition type
the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2.  This patch
adds support for locating the boot image in the first type 0xa2
partition found.

Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2017-02-17 14:15:14 -05:00
Dinh Nguyen
a45526aaa0 arm: socfpga: set the mpuclk divider in the Altera group register
The mpuclk register in the Altera group of the clock manager
divides the mpu_clk that is generated from the C0 output of the main
pll.

Without this patch, the default value of the register is 1, so the mpuclk
will always get divided by 2 if the correct value is not set. For example,
on the Arria5 socdk board, the MPU clock is only 525 MHz, and it should be
1.05 GHz.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2017-02-08 02:19:11 +01:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Bill Randle
27211b605b qts-filter.sh: strip DOS line endings and handle continuation lines
Some Altera Quartus generated files have long lines that are split with a '\' at
the end of the line. It also wOn Windows, rites files in DOS format, which can
confuse some of the processing scripts in this file. This patch solves both issues.

Signed-off-by: Bill Randle <bill.randle@gmail.com>
Cc: Marek Vasut <marex@denx.de>
2016-12-06 01:45:57 +01:00
Marek Vasut
beee6a3083 ARM: socfpga: Add boot0 hook to prevent SPL corruption
Valid Altera SoCFPGA preloader image must contain special data at
offsets 0x40, 0x44, 0x48 and valid instructions at address 0x4c or
0x50. These addresses are by default used by U-Boot's vector table
and a piece of reset handler, thus a valid preloader corrupts those
addresses slightly. While this works most of the time, this can and
does prevent the board from rebooting sometimes and triggering this
issue may even depend on compiler.

The problem is that when SoCFPGA performs warm reset, it checks the
addresses 0x40..0x4b in SRAM for a valid preloader signature and
header checksum. If those are found, it jumps to address 0x4c or
0x50 (this is unclear). These addresses are populated by the first
few instructions of arch/arm/cpu/armv7/start.S:

ffff0040 <data_abort>:
ffff0040:       ebfffffe        bl      ffff0040 <data_abort>

ffff0044 <reset>:
ffff0044:       ea000012        b       ffff0094 <save_boot_params>

ffff0048 <save_boot_params_ret>:
ffff0048:       e10f0000        mrs     r0, CPSR
ffff004c:       e200101f        and     r1, r0, #31
ffff0050:       e331001a        teq     r1, #26

Without this patch, the CPU will enter the code at 0xffff004c or
0xffff0050 , at which point the value of r0 and r1 registers is
undefined. Moreover, jumping directly to the preloader entry point
at address 0xffff0000 will also fail, because address 0xffff004.
is invalid and contains the preloader magic.

Add BOOT0 hook which reserves the area at offset 0x40..0x5f and
populates offset 0x50 with jump to the entry point. This way, the
preloader signature is stored in reserved space and can not corrupt
the SPL code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2016-12-06 01:45:56 +01:00
Anatolij Gustschin
e9c847c363 socfpga: add support for Terasic DE1-SoC board
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
2016-12-06 01:45:56 +01:00
Vagrant Cascadian
3450a8596d Fix spelling of "resetting".
Cover-Letter: Fixes several spelling errors for the words "resetting",
  "extended", "occur", and "multiple".

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-31 10:13:17 -04:00
Chin Liang See
89a54abf1b ddr: altera: Configuring SDRAM extra cycles timing parameters
To enable configuration of sdr.ctrlcfg.extratime1 register which enable
extra clocks for read to write command timing. This is critical to
ensure successful LPDDR2 interface

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2016-10-27 08:03:07 +02:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Simon Glass
02e69a5db1 Convert CONFIG_SPL_WATCHDOG_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:23 -04:00
Simon Glass
f35ed9edf3 Convert CONFIG_SPL_SPI_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:21 -04:00
Simon Glass
e404ade42d Convert CONFIG_SPL_SPI_FLASH_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:20 -04:00
Simon Glass
e00f76cee9 Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:19 -04:00
Simon Glass
d6b9bd8923 Convert CONFIG_SPL_NAND_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:14 -04:00
Simon Glass
1fdf7c64ed Convert CONFIG_SPL_MMC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:13 -04:00
Simon Glass
cc4288ef42 Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
1646eba85c Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
77d2f7f507 Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:11 -04:00
Marek Vasut
2b1cdafa9f common: Pass the boot device into spl_boot_mode()
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.

The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Marek Vasut
cf0a8dab8e ARM: socfpga: Sort Kconfig entries
Just sort the board entries, no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2016-06-08 02:57:06 +02:00
Pavel Machek
35546f6f20 ARM: socfpga: add support for IS1 board
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.

Signed-off-by: Pavel Machek <pavel@denx.de>
2016-06-08 02:56:30 +02:00
Marek Vasut
569a191a86 arm: socfpga: Add samtec VIN|ING board
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
 - 1 GiB of DRAM
 - 1 Gigabit ethernet
 - 1 USB gadget port
 - 1 USB host port with an on-board hub
 - 2 QSPI NORs connected to the Cadence QSPI core
 - Multiple I2C EEPROMs and one I2C temperature sensor

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
2016-06-01 22:44:14 +02:00
Anatolij Gustschin
5289c5fa53 socfpga: fix broken build if CONFIG_ETH_DESIGNWARE disabled
Building without ethernet driver doesn't work. Fix it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
2016-05-06 18:41:49 +02:00
Marek Vasut
dafd5792a8 arm: socfpga: Nuke useless include
The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-10 17:19:49 +02:00
Marek Vasut
5f79d00840 arm: socfpga: Handle phy-mode OF property for GMACs
Thus far, the socfpga init code had hard-coded the configuration
of the ethernet PHY interface to RGMII in the ethernet registers
in sysmgr space, so PHYs connected in another modes did not work.

This patch fixes support for configurations where the ethernet PHYs
are connected over MII/GMII/RMII interfaces by parsing the phy-mode
OF property of the GMACs and configuring the ethernet registers in
sysmgr space accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2016-04-10 17:19:48 +02:00
Marek Vasut
e6e34ca3ad arm: socfpga: Fix ethernet reset handling
The following patch caused cpu_eth_init() to not be called anymore
for DM-capable boards:

commit c32a6fd07b
Date:   Sun Jan 17 14:51:56 2016 -0700
    net: Don't call board/cpu_eth_init() with driver model

This breaks ethernet on SoCFPGA, since we use that function to un-reset
the ethernet blocks. Invoke the ethernet reset function from arch_misc_init()
instead to fix the breakage.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24 19:13:03 +01:00
Marek Vasut
80da86642b arm: socfpga: Remove bashisms from qts filter
Weed out bashisms from the script. The echo -e does not work in dash,
which is the default /bin/sh in debian .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
2016-02-24 19:13:03 +01:00
Dalon Westergreen
217db227df socfpga: Modify qts-filter args to allow input for bsp generated files and quartus project directories
The hps_isw_handoff and bsp/generated folders are typically not in the same
path.This patch adds support for specifying the different input directories for
the bsp and quartus projects.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2016-01-16 07:07:23 +01:00
Marek Vasut
8f7ed08eb3 arm: socfpga: Unreset NAND in U-Boot
Make sure the NAND reset is not asserted in full U-Boot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2015-12-22 21:30:02 +01:00
Marek Vasut
ac242e1625 arm: socfpga: Unreset NAND in SPL
If the system boots from NAND, make sure to de-assert the NAND IP
reset, otherwise the system will get stuck.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-12-22 21:30:02 +01:00
Marek Vasut
f2f3782ead arm: socfpga: Define NAND reset bit
Define the NAND reset bit and fix the ordering of the macros.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-12-22 21:30:02 +01:00
Marek Vasut
0780697787 arm: socfpga: Actually enable L2 cache
The L2 cache was never enabled in the v7_outer_cache_enable(), fix
this and enable the L2 cache.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2015-12-22 04:42:27 +01:00
Dinh Nguyen
a1684b6105 arm: socfpga: fix up a questionable macro for SDMMC
Move the macro into the socfpga_dwmci_clksel().

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
[fix parenthesis in the sdmmc_mask]
2015-12-20 03:44:56 +01:00
Dinh Nguyen
e5ad7d9889 arm: socfpga: remove building scan manager
The scan manager is not needed for the Arria10. Edit the makefile to
build the scan manager for arria5 and cyclone5 only.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-12-20 03:44:56 +01:00
Dinh Nguyen
ed77aeb575 arm: socfpga: introduce TARGET_SOCFPGA_GEN5 config property
In order to re-use as much Cyclone5 and Arria5 code as possible to support
the Arria10 platform, we need to wrap some of the code with #ifdef's. By
adding CONFIG_TARGET_SOCFPGA_GEN5, we can shorten the check by not having to check
for both AV || AV.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-12-20 03:44:56 +01:00
Marek Vasut
8e535af2e4 arm: socfpga: Introduce common board code
The SoCFPGA has reached a point where every single board code become
the same, since each and every single board is probed equally from OF.
Move the common board code into arch/arm/mach-socfpga/ .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-12-20 03:36:51 +01:00
Marek Vasut
1c75596e68 arm: socfpga: Remove cpu_mmc_init()
This function triggers the registration of the dwmmc driver on SoCFPGA,
but this is not needed in case the driver is correctly probed from DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2015-12-07 00:15:59 +01:00
Stefan Roese
ae9996c806 arm: socfpga: Add SoCFPGA SR1500 board
The SR1500 board is a CycloneV based board, similar to the EBV
SoCrates, equipped with the following devices:

- SPI NOR
- eMMC
- Ethernet

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2015-12-07 00:15:59 +01:00
Marek Vasut
856b30dae5 arm: socfpga: Repair SoCrates board
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
2015-11-30 13:30:19 +01:00
Dinh Nguyen
871c24bc50 ARM: socfpga: rename the cyclone5 and arria5 base address file
When adding support for the Arria10 platform, we're going to name the file
base_addr_a10.h, so to be systematic about it, rename the socfpga_base_addr.h
to be base_addr_ac5.h for the Arria5 and Cyclone5 platform.

Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-11-30 13:30:19 +01:00
Dinh Nguyen
5a7152e4fd ARM: socfpga: arria10: add base address map for Arria10
Add the base address map for Arria10.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-11-30 13:30:19 +01:00
Philipp Rosenberger
8a30e3a73a arm: socfpga: reset: FIX address of tstscratch register
The Cyclone V Hard Processor System Technical Reference Manual in the
chapter about the Reset Manager Module Address Map stats that the offset
of the tstscratch register ist 0x54 not 0x24.

Cyclone V Hard Processor System Technical Reference Manual cv_5v4 2015.11.02
page 3-17 Reset Manager Module Address Map

Signed-off-by: Philipp Rosenberger <ilu@linutronix.de>
2015-11-30 13:30:19 +01:00
Dinh Nguyen
c624d07f3f arm: socfpga: reset: correct dma, qspi, and sdmmc reset bit defines
The DMA, QSPI, and SD/MMC reset bits are located in the permodrst register,
not the mpumodrst. So the bank for these reset bits should be 1, not 0.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-11-03 17:32:16 +01:00
Dinh Nguyen
8d8e13e129 arm: socfpga: enable data/inst prefetch and shared override in the L2
Update the L2 AUX CTRL settings for the SoCFPGA.

Enabling D and I prefetch bits helps improve SDRAM performance on the
platform.

Also, we need to enable bit 22 of the L2. By not having bit 22 set in the
PL310 Auxiliary Control register (shared attribute override enable) has the
side effect of transforming Normal Shared Non-cacheable reads into Cacheable
no-allocate reads.

Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-10-17 01:47:31 +02:00
Dinh Nguyen
3cbc7b878b arm: socfpga: rename socfpga_cyclone5 and socfpga_arria5 config files
Rename the socfpga_cyclone5.h to socfpga_cyclone5_socdk.h, and
socfpga_arria.h to socfpga_arria5_socdk.h. This matches the other SoCFPGA
board config files.

Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-09-23 03:55:28 +02:00
Dinh Nguyen
55c7a765f6 arm: socfpga: Add support for the Terasic DE-0 Atlas board
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
based board. The board can boot from SD/MMC. Ethernet is also supported.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-09-04 11:54:21 +02:00
Marek Vasut
d88995a82b arm: socfpga: Add support for DENX MCV SoM and MCVEVK board
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-09-04 11:54:21 +02:00
Marek Vasut
952caa289e arm: socfpga: Add support for Terasic SoCkit board
Add support for Terasic SoCkit, which is CycloneV based board.
The board can boot either from SD/MMC or QSPI. Ethernet is also
supported.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-09-04 11:54:21 +02:00
Marek Vasut
a665b051b5 arm: socfpga: Do not call board_init_r() from board_init_f()
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the SoCFPGA SPL with the correct SPL design as well as reduces
the stack utilisation slightly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-09-04 11:54:20 +02:00
Marek Vasut
65d372c44c arm: socfpga: Assure ISWGRP 0 and 1 are inited
This fix makes sure that the ISWGRP0 and ISWGRP1 registers are
correctly inited. In case those registers are not initialized,
it is not possible to access the registers synthesised in the
FPGA through the bridges. Any such access produces data abort.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-09-04 11:54:20 +02:00
Marek Vasut
129adf5bf4 mmc: dw_mmc: Probe the MMC from OF
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.

This patch now also removes previous temporary workaround.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
2015-09-04 11:54:20 +02:00
Marek Vasut
cc9429a556 arm: socfpga: Make the pinmux table const u8
Now that we're actually converting the QTS-generated header files,
we can even adjust their data types. A good candidate for this is
the pinmux table, where each entry can have value in the range of
0..3, but each element is declared as unsigned long. By changing
the type to u8, we can save over 600 Bytes from the SPL, so do it.
This patch also constifies the array.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:20 +02:00
Marek Vasut
f6badb0d89 arm: socfpga: Switch to filtered QTS files
Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:20 +02:00
Marek Vasut
e996b9362b arm: socfpga: Add qts-filter.sh script
Add script which loads the QTS-generated sources and headers and converts
them into sensible format which can be used with much more easy in mainline
U-Boot. The script also filters out macros which makes no sense anymore, so
they don't pollute namespace and waste space.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:20 +02:00
Marek Vasut
f089240128 arm: socfpga: Split Altera socfpga into AV and CV SoCDK
The board/altera/socfpga directory is not a generic SoCFPGA machine
anymore, but instead it represents the Altera SoCDK board. To make
matters more complicated, it represents both CycloneV and ArriaV
variant.

On the other hand, nowadays, the content of this board directory is
mostly comprised of QTS-generated header files, while all the generic
code is in arch/arm/mach-socfpga already.

Thus, this patch splits the board/altera/socfpga into a separate
board directory for ArriaV SoCDK and CycloneV SoCDK, so that each
can be populated with the correct QTS-generated header files for
that particular board.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:19 +02:00
Marek Vasut
cd9b731771 arm: socfpga: Unbind CPU type from board type
The CONFIG_TARGET_SOCFPGA_CYCLONE5 and CONFIG_TARGET_SOCFPGA_ARRIA5
selected both a board and a CPU. This is not correct as these macros
are supposed to select only board.

All would be good, if QTS-generated header files didn't check for
these macros exactly to determine if the platform is Cyclone V or
Arria V. Thus, for the sake of compatibility with not well fleshed
out header file generator, this patch makes these two macros into
a stub config option and introduces new CONFIG_TARGET_SOCFPGA_CYCLONE5_SOCDK
and CONFIG_TARGET_SOCFPGA_ARRIA5_SOCDK targets, which select the
previous stub config option.

The result is that compatibility with QTS is preserved and the new
CONFIG_TARGET_* select actual target boards.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:19 +02:00
Marek Vasut
ca62d2e1fc arm: socfpga: Move wrappers into platform directory
Move the wrappers for QTS-generated files into platform directory
out of the board directory. The trick here is to add -I to CFLAGS
such that it points to the board directory in source tree and thus
the qts/ directory there is still reachable.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:19 +02:00
Marek Vasut
7e4d2fa2ed arm: socfpga: Fix delay in clock manager
This code claims it needs to wait 7us, yet it uses get_timer() function
which operates with millisecond granularity. Use timer_get_us() instead,
which operates with microsecond granularity.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:19 +02:00
Marek Vasut
a8535c306c arm: socfpga: Fix delay in freeze controller
Based on observation, this udelay(20) was apparently too high and caused
subsequent failure to calibrate DDR when U-Boot was compiled with certain
toolchains. Lowering this delay fixed the problem.

Instead of permanently lowering the delay, calculate the correct delay
based on the original comment, that is, obtain EOSC1 frequency and use
it to calculate the precise delay.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23 11:56:19 +02:00
Dinh Nguyen
bd48c0617b arm: socfpga: misc: Add support for printing FPGA type
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:30 +02:00
Dinh Nguyen
bd0f5a91f3 arm: socfpga: scan: Add code to get FPGA ID
Add code to get the FPGA type for Altera's SoCFPGA family of FPGA. The code
uses the scan manager to send jtag pulses that will return the FPGA ID.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:30 +02:00
Marek Vasut
5e19b68aa1 arm: socfpga: scan: Factor out IO chain programming
Factor out the code which sends JTAG instruction followed by data
into separate function to tidy the code up a little.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:30 +02:00
Marek Vasut
62a0c9cff3 arm: socfpga: scan: Clean up horrible macros
Clean up the horrible macros present in the scan_manager.h . Firstly,
the function scan_mgr_io_scan_chain_prg() is static, yet all the macros
are used only within it, thus there is no point in having them in the
header file. Moreover, the macros are just making the code much less
readable, so remove them instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:30 +02:00
Marek Vasut
66acc190e9 arm: socfpga: scan: Introduce generic JTAG accessor
Introduce generic function for accessing the JTAG scan chains in the
SCC manager. Make use of this function throughout the SCC manager to
replace the ad-hoc writes to registers and make the code less cryptic.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:30 +02:00
Marek Vasut
aa5659ac65 arm: socfpga: scan: Clean up scan_chain_engine_is_idle()
Rework this function so it's clear that it is only polling for certain
bits to be cleared. Add kerneldoc. Fix it's return value to be either
0 on success and -ETIMEDOUT on error and propagate this through the
scan manager code.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:30 +02:00
Marek Vasut
042ff2d0fa ddr: altera: sequencer: Wrap misc remaining macros
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:29 +02:00
Marek Vasut
10c14261f3 ddr: altera: sequencer: Wrap IO_* macros
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:29 +02:00
Marek Vasut
d718a26b0c ddr: altera: sequencer: Wrap RW_MGR_* macros
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:29 +02:00
Marek Vasut
04955cf247 ddr: altera: sequencer: Wrap ac_rom_init and inst_rom_init
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:28 +02:00
Marek Vasut
c4ecc98974 ddr: altera: sequencer: Clean up mach/sdram.h
Zap non-existent functions and place function prototypes at the
beginning of the header file.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08 14:14:28 +02:00
Marek Vasut
5af914189e ddr: altera: sdram: Introduce socfpga_sdram_get_config()
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:27 +02:00
Marek Vasut
99f453e953 ddr: altera: sdram: Clean up sdram_mmr_init_full() part 8
Fix the return value so that standard errno return values can be used.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:27 +02:00
Marek Vasut
03439e4064 arm: socfpga: Add temporary workaround for missing SD/MMC patches
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.

The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:25 +02:00
Marek Vasut
17fdc9167f ddr: altera: Wrap SOCFPGA_SDR_ADDRESS into SDR_PHYGRP.*ADDRESS
Just trim down the constant SOCFPGA_SDR_ADDRESS + SDR_PHYGRP.*ADDRESS
in the code.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:11 +02:00
Marek Vasut
7599b53dc1 arm: socfpga: config: Move SPL GD and malloc to RAM
Now that the SPL structure is organised such that it matches the
U-Boot's SPL design, it is possible to use the option of relocating
GD to RAM. And since we have GD in RAM, move malloc area to RAM as
well. We point the malloc base pointer 1 MiB past U-Boot's load
address. We use simple malloc for SPL because it is 3kiB smaller
in terms of code size than regular malloc which was used thus far.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:09 +02:00
Marek Vasut
6ab00db226 arm: socfpga: misc: Reset ethernet from OF
Reset the GMAC ethernets based on the "resets" OF node instead of ad-hoc
hardcoded values in the U-Boot code. Since we don't have a proper reset
framework in place yet, we have to do this slightly ad-hoc parsing of the
OF tree instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2015-08-08 14:14:08 +02:00
Marek Vasut
e14d3f7928 arm: socfpga: misc: Probe ethernet GMAC from OF
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2015-08-08 14:14:08 +02:00
Marek Vasut
9ec7414e29 arm: socfpga: misc: Export bootmode into environment variable
setenv an environment variable called "bootmode" , which contains the
board boot mode. This can be in turn used in scripts to determine from
where to load kernel and such.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
d85e311e7f arm: socfpga: misc: Add support for printing boot mode
Add support for printing from which device the SoCFPGA board booted.
This decodes the BSEL settings and prints it in human readable form.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
ef84861b7d arm: socfpga: misc: Fix warm reset
Write necessary magic value into the Warm Boot from ON-Chip RAM
group Enable register to enable Warm reset support. Instead of
doing this in the reset_cpu() function, we do it in arch early
init to avoid breaking old kernel code which expects this magic
value to be already written into this register.

This magic is originally excavated from common/spl/spl.c in the
u-boot port from altera, where this value was written just before
the SPL jumped to actual U-Boot in the RAM.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
066ad14a22 arm: socfpga: spl: Add support for selecting boot device from BSEL
Rework spl_boot_device() such that it reads the BSEL settings from
system manager and decides from where to load U-Boot based on this
information.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
346d6f5667 arm: socfpga: spl: Add support for booting from QSPI
Add code and configuration options to support booting from QSPI NOR.
Enable support for booting from QSPI NOR.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
d3f34e752d arm: socfpga: spl: Add support for booting from SD/MMC
Add code and configuration options to support booting from RAW
SD/MMC card as well as for ext4/vfat filesystems. Enable support
for booting from SD/MMC card, but don't enable the filesystem
support just yet to retain compatibility with old SoCFPGA card
format.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
1d8c939391 arm: socfpga: spl: Remove custom linker script
Remove the custom SPL linker script, use the generic one instead.
The custom script doesn't bring in anything new and is only burden
to maintain.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:08 +02:00
Marek Vasut
6473054a12 arm: socfpga: spl: Merge spl_board_init() into board_init_f()
The code in spl_board_init() should have been in board_init_f()
from the beginning, since it is code which configures system and
then starts DRAM. Thus, it cannot be in spl_board_init(), which
is called from board_init_r() , which already expects a working
DRAM.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
bd65fe35ff arm: socfpga: spl: Add missing reset logic
Make sure that all the peripherals are correctly reset and then
brought out of reset in the SPL. Not going through proper reset
cycle might leave the IP blocks in inconsistent state.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
232fcc6e9d arm: socfpga: spl: Configure SCU and NIC-301 early
Configure the ARM SCU and NIC301 very early. The ARM SCU SNSAC register
must be configured, so we can access all peripherals. The NIC-301 must
be configured so that the BootROM is not mapped into the SDRAM address
space.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
4a0080d985 arm: socfpga: spl: Toggle warm reset config I/O bit
Synchronise the SPL behavior with the original Altera code and
toggle the Warm Reset Config I/O bit accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
2d779b39b4 arm: socfpga: system: Clean up pinmux_config.c
Implement new accessor, sysmgr_get_pinmux_table(), used to obtain pinmux
table and it's size from the QTS-generated pinmux_config.c. The target
here is again to get rid of poluting global namespace by including the
pinmux_config.h into it.

Furthermore, the pinmux_config.h declares some CONFIG_HPS_* macros,
which are explicitly useless to us in U-Boot. Instead, U-Boot does
use DT to detect exactly these configuration options. This patch
makes sure that while this QTS-generated file can stay in the tree,
these obscure macros do not ooze into the namespace anymore.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
40687b4f46 arm: socfpga: system: Rework sysmgr_enable_warmrstcfgio()
Rework sysmgr_enable_warmrstcfgio() into sysmgr_config_warmrstcfgio(),
which allows both enabling and disabling the warm reset config I/O
functionality.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00
Marek Vasut
575d741516 arm: socfpga: scan: Zap iocsr_scan_chain*_table()
Introduce accessor iocsr_get_config_table() for retrieving IOCSR config
tables. This patch is again trimming down the namespace polution.

The IOCSR config tables are used only by scan manager, they are generated
by qts and are board specific. Before this patch, the approach to use
these tables in scan manager was to define an extern variable to silence
the compiler and compile board-specific iocsr_config.c into U-Boot which
defined those extern variables. Furthermore, since these are tables and
the scan manager needs to know the size of those tables, iocsr_config.h
is included build-wide.

This patch wraps all this into a single accessor which takes the scan
chain ID and returns pointer to the table and it's size. All this is
wrapped in wrap_iocsr_config.c board-specific file. The file includes
the iocsr_config.c (!) to access the original tables and transitively
iocsr_config.h . It is thus no longer necessary to include iocsr_config.h
build-wide and the namespace polution is trimmed some more.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08 14:14:07 +02:00