Commit graph

759 commits

Author SHA1 Message Date
Max Krummenacher
e1c29086d5 nand: nand torture: follow sync with linux v4.6
follow parameter name change (nand to mtd) to fix compiler error.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-06-19 19:19:30 -05:00
Boris Brezillon
7748b41482 spl: nand: sunxi: add support for NAND config auto-detection
NAND chips are supposed to expose their capabilities through advanced
mechanisms like READID, ONFI or JEDEC parameter tables. While those
methods are appropriate for the bootloader itself, it's way to
complicated and takes too much space to fit in the SPL.

Replace those mechanisms by a dumb 'trial and error' mechanism.

With this new approach we can get rid of the fixed config list that was
used in the sunxi NAND SPL driver.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19 19:12:02 -05:00
Boris Brezillon
4e7d1b3beb spl: nand: sunxi: split 'load page' and 'read page' logic
Split the 'load page' and 'read page' logic in 2 different functions so
we can later load the page and test different ECC configs without the
penalty of reloading the same page in the NAND cache.

We also move common setup to a dedicated function (nand_apply_config()) to
avoid rewriting the same values in NFC registers each time we read a page.

These new functions are passed a pointer to an nfc_config struct to limit
the number of parameters.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19 19:12:01 -05:00
Boris Brezillon
bb9783b66b spl: nand: sunxi: rework status polling loop
check_value_xxx() helpers are using a 1ms delay between each test, which
can be quite long for some operations (like a page read on an SLC NAND).
Since we don't have anything to do but to poll this register, reduce the
delay between each test to 1us.

While we're at it, rename the max_number_of_retries parameters and the
MAX_RETRIES macro into timeout_us and DEFAULT_TIMEOUT_US to reflect that
we're actually waiting a given amount of time and not only a number of
retries.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19 19:12:01 -05:00
Boris Brezillon
fa30115878 spl: nand: sunxi: stop guessing the redundant u-boot offset
Use CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND value instead of trying to guess
where the redundant u-boot image is based on simple (and most of the time
erroneous) heuristics.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

# Conflicts:
#	drivers/mtd/nand/sunxi_nand_spl.c
2016-06-19 19:12:01 -05:00
Boris Brezillon
80ef700f8d spl: nand: support redundant u-boot image
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.

Add an extra Kconfig option to specify the offset of the redundant u-boot
image.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-19 19:11:57 -05:00
Boris Brezillon
494e108651 spl: nand: rework SYS_NAND_U_BOOT_OFFS Kconfig option dependency
The SYS_NAND_U_BOOT_OFFS is quite generic, but the Kconfig entry is forced
to explicitly depend on platforms that are not already defining it in their
include/configs/<board>.h header.

Add the SYS_NAND_U_BOOT_LOCATIONS option, make the SYS_NAND_U_BOOT_OFFS
depends on it, remove the dependency on NAND_SUNXI and make it dependent
on SPL selection.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19 19:11:48 -05:00
Boris Brezillon
c4adf9db5d spl: nand: sunxi: remove support for so-called 'syndrome' mode
The sunxi SPL NAND controller driver supports use 'BootROM'-like configs,
that is, configs where the ECC bytes and real data are interleaved in the
page instead of putting ECC bytes in the OOB area.

Doing that has several drawbacks:
- since you're interleaving data and ECC bytes you can't use the whole page
  otherwise you might override the bad block marker with non-FF bytes.
- to solve the bad block marker problem, the ROM code supports partially
  using the page, but this introduces a huge penalty both in term of read
  speed and NAND memory usage. While this is fine for rather small
  binaries(like the SPL one which is at maximum 24KB large), it becomes
  non-negligible for the bootloader image (several hundred of KB).
- auto-detection of the page size is not reliable (this is in my opinion
  the biggest problem). If you get the page size wrong, you'll end up
  reading data at a different offset than what was specified by the caller
  and the reading may succeed (if valid data were written at this address).

For all those reasons I think it's wiser to completely remove support for
'syndrome' configs. If we ever need to support it again, then I'd recommend
specifying all the config parameters through Kconfig options.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19 18:52:35 -05:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Andre Renaud
65319f15ca at91: nand: Set up the ECC strength correctly
This needs to be set to avoid a fatal error when ECC is used.

Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Andre Renaud
5a9ae33316 at91: Correct NAND ECC register access
This uses the wrote base register value. Fix it.

Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Tom Rini
3fc304b8d7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-06-12 12:51:34 -04:00
Heiko Schocher
3a504d9639 mtd: nand: omap: allow to switch to BCH16
support in omap_nand_switch_ecc() also an eccstrength
from 16.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:12 -04:00
Heiko Schocher
5d29e27eb9 nand: add nand mtd concat support
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:12 -04:00
Max Krummenacher
667067faa1 nand: fix nand torture to use changed mtd api
The mtd subsystem deprecated and renamed the direct use of the mtd_info
struct's functionpointers. Instead the corresponding mtd_xxx function
should be used.

See also:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=3c3c10bba1e4ccb75b41442e45c1a072f6cded19

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-06-03 20:29:05 -05:00
Scott Wood
ceee07b658 mtd: nand: Sync with Linux v4.6
Updates the NAND code to match Linux v4.6.  The previous sync was from
Linux v4.1 in commit d3963721d9.

Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.

Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
2016-06-03 20:27:48 -05:00
Scott Wood
81c772521f mtd: nand: Add page argument to write_page() etc.
This change is part of the Linux 4.6 sync.  It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Scott Wood
17cb4b8f32 mtd: nand: Add+use mtd_to/from_nand and nand_get/set_controller_data
These functions are part of the Linux 4.6 sync.  They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Scott Wood
b616d9b0a7 nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Scott Wood
151c06ec61 mtd: nand: Remove nand_info_t typedef
This typedef serves no purpose other than causing confusion with
struct nand_chip.

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Scott Wood
ea7d1eec66 mtd: nand: Remove docg4 driver and palmtreo680 flashing tool
Commit ad4f54ea86 ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool.  This
patch removes them.

Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
2016-06-03 20:27:48 -05:00
Marek Vasut
5d74e3a6f1 mtd: nand: Remove jz4740 driver
This driver is not used by anyone, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Siva Durga Prasad Paladugu
a39d14406a mtd: nand: arasan_nfc: Correct nand ecc initialization
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
2016-06-03 20:27:48 -05:00
Lokesh Vutla
0985294604 mtd: nand: am335x: spl: Fix copying of image
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:41:41 -04:00
Peng Fan
9aa550d2e8 mtd: nand: mxs: use simpler runtime cpu dection macros
Use simpler runtime cpu dection macros.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Scott Wood <oss@buserror.net>
2016-05-24 14:59:57 +02:00
Vagrant Cascadian
eae4b2b67b Fix spelling of "occurred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-02 18:37:09 -04:00
Purna Chandra Mandal
6d9481047e drivers: remove writes{b,w,l,q} and reads{b,w,l,q}.
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
2016-04-10 17:18:41 +02:00
Chris Packham
46a16bd895 kirkwood_nand: claim MPP pins on the fly
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.

Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-04-06 15:40:33 +02:00
Graham Moore
15305c2f03 mtd: nand: denali: max_banks calculation changed in revision 5.1
Read Denali hardware revision number and use it to
calculate max_banks,  The encoding of max_banks changed
in Denali revision 5.1.

[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]

Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:16:55 +09:00
Masahiro Yamada
73b5b27b7a mtd: denali: fix warning when compiled for 64bit system
The 64-bit compiler (ex. aarch64) emits "warning: cast from pointer
to integer of different size".

Make it work with 64bit DMA address while I am here.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-24 01:36:49 +09:00
Siva Durga Prasad Paladugu
e4b40e921d arasan: nfc: Add initial nand driver support for arasan
Added initial nand driver support for arasan nand flash
controller.This supports nand erase,nand read, nand write
This uses the hardware ECC for read and write operations
ZynqMP uses this  driver.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warnings]
Signed-off-by: Scott Wood <oss@buserror.net>
2016-02-12 17:27:41 -06:00
Siva Durga Prasad Paladugu
78cb965af0 zynqmp: nand: Add Nand driver support for zynqmp
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
2016-02-12 17:27:28 -06:00
Kevin Smith
065a373d93 mtd: pxa3xx_nand: Don't alloc unneeded memory
The allocation size is reduced from what was introduced from the
Linux kernel, as U-boot uses the statically allocated nand_info
instead of needing to dynamically allocate an mtd_info instance.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
2016-02-12 17:13:50 -06:00
Kevin Smith
84caff35df mtd: pxa3xx_nand: Correct offset calculation
Correct some pointer math in initialization.  An offset was added
to a struct-typed pointer instead of one casted to a byte-size,
resulting in a much larger offset than intended.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
2016-02-12 17:13:47 -06:00
Kevin Smith
b7d3e4a635 mtd: pxa3xx_nand: Correct null dereference
Correct a null pointer dereference in board_nand_init().  Zeroed
memory was allocated, then immediately dereferenced.  The
dereference is completely removed, since this pointer is later
initialized in alloc_nand_resources.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
2016-02-12 17:13:42 -06:00
Peng Fan
549d7c0e09 nand: mxs: fix error handling for mxs_nand_init
Fix error handling for mxs_nand_init.

The original error handling is wrong for err2 and err1.
Should first free desc[x], then free desc.

This patch also correctly handle err3, should use
MXS_DMA_CHANNEL_AHB_APBH_GPMI0 as the check point.

Cc: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-02-12 17:10:15 -06:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Josh Wu
258b21fc69 atmel_nand: Add 32 bit ecc support for sama5d2 chip
Also if minimum ecc requirment is bigger then what we support, then just
use our maxium pmecc support.
But it is not safe, so we'll output a warning about this.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-02 11:49:11 +01:00
Josh Wu
fa651f5d53 atmel_nand_ecc: update pmecc registers according to sama5d2 chip
1. add the pmecc register mapping for sama5d2.
2. add the pmecc error location register mapping for sama5d2.
3. add some new field that is different from old ip.
4. add sama5d2 pmecc ip version number.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-02 11:49:10 +01:00
Josh Wu
422b49e289 atmel_nand: use the definition: PMECC_OOB_RESERVED_BYTES instead magic number
As atmel_nand_ecc.h is sync with v4.1 kernel, which adds the
PMECC_OOB_RESERVED_BYTES. So use it in the driver.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2016-01-27 13:58:59 +01:00
Josh Wu
4c6a6ea3e1 atmel_nand: add '\n' in the end of error message for better display
Also align the open parenthesis.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-27 13:58:59 +01:00
Josh Wu
3a20567199 atmel_nand: use nand ecc_{strength, step}_ds instead of our own function
Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2016-01-27 13:58:58 +01:00
Peng Fan
bedaa842ae imx: nand: update GPMI NAND driver to support MX7
Update GPMI NAND driver and BCH head file to support i.MX7

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:09:32 +01:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Vagrant Cascadian
1b25e586cb Fix typo: firstly -> first.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Marek Vasut <marex@denx.de>
2015-12-05 18:22:23 -05:00
Simon Glass
24b852a7a2 Move console definitions into a new console.h file
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:27:50 -07:00
Tom Rini
cb4c833b74 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-10-15 08:43:38 -04:00
Stefan Agner
e24bb2b732 mtd: nand: vf610_nfc: resync with upstream Linux version
This resyncs the driver changes with the Linux version of the
driver. The driver received some feedback in the LKML and got
recently acceppted, the latest version can be found here:
https://lkml.org/lkml/2015/9/2/678

Notable changes are:
- On ECC error, reread OOB and count bit flips in OOB too.
  If flipped bits are below threshold, also return an empty
  OOB buffer.
- Return the amount of bit flips in vf610_nfc_read_page.
- Use endianness aware vf610_nfc_read to read ECC status.
- Do not enable IDLE IRQ (since we do not operate with an
  interrupt service routine).
- Use type safe struct for buffer variants (vf610_nfc_alt_buf).
- Renamed variables in struct vf610_nfc (column and page_sz)
  to reflect better what they really representing.

The U-Boot version currently does not support RAW NAND write
when using the HW ECC engine.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-10-15 11:10:44 +02:00
Ezequiel García
d1d0167663 nand: omap_gpmc: Change correctable bit-flips messages to debug()
Messages on corrected bit-flips are not really useful,
as bit-flips are perfectly normal. Let's avoid cluttering
the console and make them debug.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
2015-10-11 17:12:13 -04:00
Hans de Goede
31c5614af4 sunxi_nand_spl: Be smarter about where to look for backup u-boot.bin
We know when u-boot is written to its own partition, in this case the
layout always is:

eb 0 spl
eb 1 spl-backup
eb 2 u-boot
eb 3 u-boot-backup

eb: erase-block

So if we cannot load u-boot from its primary offset we know exactly where
to look for it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-29 11:50:07 +02:00
Peng Fan
168617c9b5 mtd: nand: mxs check maximum ecc that platfrom supports
Check maximum ecc strength for each platfrom to avoid the calculated ecc
exceed the limitation.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Han Xu <b45815@freescale.com>
Tested-By: Tim Harvey <tharvey at gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-20 09:59:54 +02:00
Stefan Roese
62c390f8a3 mtd: nand: fsmc: Fixes and cleanup for fsmc_nand_switch_ecc()
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:

- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
  ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
  will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
  not supporting the BCH8 HW ECC (FSMC_VER8)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-09-15 15:05:21 -04:00
Heiko Schocher
92a3188d7d bitops: introduce BIT() definition
introduce BIT() definition, used in at91_udc gadget
driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-09-11 17:15:32 -04:00
Simon Glass
cf92e05c01 Move ALLOC_CACHE_ALIGN_BUFFER() to the new memalign.h header
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 17:15:20 -04:00
Simon Glass
6e295186c7 Move malloc_cache_aligned() to its own header
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:

   4519668 mtd/nand/ubi: assortment of alignment fixes

This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.

Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2015-09-11 17:15:16 -04:00
Stefan Roese
1a103c6caa mtd: nand: fsmc: Add BCH4 SW ECC support for SPEAr600
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.

To enable SW BCH4, you need to specify this in your config header:

#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH

And use the command "nandecc bch4" to select this ECC scheme upon runtime.

Tested on SPEAr600 x600 board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2015-09-11 17:15:13 -04:00
Simon Glass
0abdd9d01a arm: Remove nhk8815 boards and nomadik arch
These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:04 -04:00
Stefan Roese
cc19722f04 sunxi_nand_spl: Add config parameter for 4KiB page sized NAND devices
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-10 20:20:45 +02:00
Hans de Goede
d90ba790d8 mtd: nand: Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.

Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-31 08:43:42 +02:00
Boris Brezillon
ddd37fe865 sunxi_nand_spl: clear status flags in SPL implementation
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Hans de Goede
6a08d65acc sunxi_nand_spl: Remove NAND_SUNXI_SPL_SYNDROME_PARTITIONS_END
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.

Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.

Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
e526861687 sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.

Renaming the Kconfig option now makes things easier when we add full
nand support in the future.

The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
24a06c964f sunxi_nand_spl: Add support for backup boot partitions
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.

This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
2b8a01a99d sunxi_nand_spl: Auto detect nand configuration parameters
Auto detect the nand configuration parameters, like the BROM does.

This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.

The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.

Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
f5916d1856 sunxi_nand_spl: Parametrize lowlevel read functions
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.

This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
0a247554c2 sunxi_nand_spl: Properly config page-size in the nand ctl register
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
022a99d8b2 sunxi_nand_spl: Add support for sun4i and sun5i SoCs
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.

Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
008ac1dfe0 sunxi_nand_spl: Use kernel driver algorithm for determining ecc_mode / _off
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
2a43973f64 sunxi_nand_spl: Add proper cache flusing
We are using dma, so we should flush the cache before starting the dma,
and invalidate it once the dma is done.

Things are working without this by mostly luck, but lets not rely on that.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
5d65c67bf1 sunxi_nand_spl: Turn off clocks when we're done with the nand
Turn off the nand and dma clocks when we're done with the nand, this
puts the nand and dma controllers back into a clean state for when the
kernel boots.

Without this the kernel will not boot properly when it is built with
dma-controller support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
f62bfa56da sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary
Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
9da5fca55c sunxi_nand_spl: Do not bother writing the spare-area reg in syndrome mode
In syndrome mode we set the NFC_SEQ bit in the command register, so the
spare-area register is not used. Also the value currently being written is
actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE"
not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE.

So the current code only serves to confuse the user -> remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
630cf2e762 sunxi_nand_spl: We only need to reset the nand chip once
There is no need to reset the nand chip for every ecc-block read.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
10d069b797 sunxi_nand_spl: Drop unnecessary temp buf
nand_spl_load_image() always gets called with either CONFIG_SYS_TEXT_BASE
or spl_image.load_addr as destination, both of which are properly aligened,
and have plenty of space for "overshooting" up to
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes, as we read in
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes chunks.

This saves CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE (typically 1k) in
SPL size, which is a lot on the total 24k we have.

Note this changes the dma destination from SRAM to DRAM, so this patch
updates the DDMA_DST_TYPE bits in the dma controller cfg0 reg accordingly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Masahiro Yamada
2bc1f2b592 mtd: denali_spl: do not allocate page_buffer in .bss section
Since commit 2580a2a7e7 ("mtd: nand: Increase max sizes of OOB and
Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build
with the following error message:
  arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big

They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer
as static data:

    static uint8_t page_buffer[NAND_MAX_PAGESIZE];

This buffer required 8KB in .bss section before that commit and now
it has been increased to 16KB.  Given limited code/memory size for SPL,
it is not a good idea to allocate a page buffer statically.  In the
first place, the load address 'dst' can be used as a page buffer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-08-30 22:18:00 +09:00
Marcel Ziswiler
4519668b29 mtd/nand/ubi: assortment of alignment fixes
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:

ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:17 -04:00
Peng Fan
ecfb8768b1 mtd: nand: mxs invalidate dcache before DMA read
Follow linux dma flow:
Before DMA read, be sure to invalidate the cache over the address
range of DMA buffer to prevent cache coherency problems.
After DMA read, invalidate dcache again.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2015-08-25 22:53:59 -05:00
Peng Fan
63b29d8082 mtd: nand: mxs support oobsize bigger than 512
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.

The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.

   |                          P                                        |
   |<----------------------------------------------------------------->|
   |                                                                   |
   |                                                (Block Mark)       |
   |                      P'                             |           | |   |
   |<--------------------------------------------------->|     D     | | O'|
   |                                                     |<--------->| |<->|
   V                                                     V           V V   V
   +---+--------------+-+--------------+-+--------------+-+----------+-+---+
   | M |   data       |E|   data       |E|   data       |E|   data   |E|   |
   +---+--------------+-+--------------+-+--------------+-+----------+-+---+
                                                        ^                  ^
                                                        |         O        |
                                                        |<---------------->|

       P : the page size for BCH module.
       E : The ECC strength.
       G : the length of Galois Field.
       N : The chunk count of per page.
       M : the metasize of per page.
       C : the ecc chunk size, aka the "data" above.
       P': the nand chip's page size.
       O : the nand chip's oob size.
       O': the free oob.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
2015-08-25 22:53:58 -05:00
Stefan Roese
873960c89e mtd: nand: Add mvebu (PXA / AXP / A38x) NAND device driver
Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:

http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html

Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:

https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html

Otherwise it will not compile.

Tested on the Marvell Armada XP DB-MV784MP-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:58 -05:00
Scott Wood
d3963721d9 nand: Sync with Linux v4.1
Update the NAND code to match Linux v4.1.  The previous sync was
from Linux v3.15 in commit 4e67c57125.

CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout.  Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Ezequiel Garcia
86a720aafc mtd: Introduce mtd_block_isreserved()
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().

While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Scott Wood
273310644f nand: Remove __UBOOT__ ifdefs
I didn't approve the patch that added them.  Get them out of the way
before doing a sync.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Sylvain Lemieux
30cb3bf4a9 nand: lpc32xx: add ECC layout for small page NAND
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)

This layout is matching the lpc32xx NAND SLC Linux Kernel driver.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-18 13:45:56 -04:00
Sylvain Lemieux
5f63bf3ec8 nand: lpc32xx: add hardware ECC support
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition

The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:56 -04:00
Marcel Ziswiler
6eeedc196d tegra: nand: disable subpage writes
Disable subpage writes as we do not provide ecc->hwctl.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:03 -07:00
Marcel Ziswiler
adf4800d85 mtd/nand/tegra: alignment workaround
Integrate cache alignment bounce buffer to workaround issues as follows:

Loading file '/boot/zImage' to addr 0x01000000 with size 4499152 (0x0044a6d0)...
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Done
Kernel image @ 0x1000000 [ 0x000000 - 0x44a6d0 ]

Starting kernel ...

undefined instruction
pc : [<005ff03c>]          lr : [<0000800c>]
sp : 0144b6e8  ip : 01000188     fp : 0144a6c8
r10: 00000000  r9 : 411fc090     r8 : 00000100
r7 : 00000cfb  r6 : 0144a6d0     r5 : 00000000  r4 : 00008000
r3 : 0000000c  r2 : 00000100     r1 : 00000cfb  r0 : 00000000
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:02 -07:00
Marcel Ziswiler
1bc66a57c0 tegra: nand: fix read_byte required for proper onfi detection
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.

This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).

I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:02 -07:00
Vladimir Zapolskiy
dcfd37e5ef nand: lpc32xx: add SLC NAND controller support
The change adds support of LPC32xx SLC NAND controller.

LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.

This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.

Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.

The driver can be included to an SPL image.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-12 20:47:33 -04:00
Vladimir Zapolskiy
8d1809a966 spl: nand: simple: replace readb() with chip specific read_buf()
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.

NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-12 20:47:33 -04:00
Heiko Schocher
c10ac540ea nand, atmel: remove udelay in spl_nand_erase_one()
remove unneeded udelay() in this function, as we use
the dev_ready pin.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-12 20:47:27 -04:00
Piotr Zierhoffer
960caeba8f sunxi: nand: Add board configuration options
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.

This commit also introduces the configurable options in Kconfig.

Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-08 16:26:19 +02:00
Piotr Zierhoffer
aeb4b0d3b3 sunxi: nand: Add basic sunxi NAND driver for SPL with DMA support
This driver adds NAND support to SPL.
It was tested on Allwinner A20.

Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-08 16:26:19 +02:00
Ian Campbell
da9971d1b3 Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory"
This reverts commit f76eba38b3.

This patch did not have a full and proper copyright/S-o-b chain.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

Conflicts:
	include/configs/sun6i.h
	include/configs/sun8i.h
2015-06-28 11:46:31 -04:00
Jeroen Hofstee
cb2fc338f8 mtd: OMAP: Enable GPMC prefetch mode for 16 bit access
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 11:23:45 -04:00
Jeroen Hofstee
c07361145f omap_gpmc: move prefetch out of CONFIG_NAND_OMAP_ELM
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 11:23:45 -04:00
Daniel Kochmański
f76eba38b3 sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Stefan Agner
8fca2d8cb8 mtd: vf610_nfc: enable ONFI detection
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:27:46 -05:00
Stefan Agner
080a71e8e9 mtd: vf610_nfc: add 32-error correction option for HW ECC
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:27:46 -05:00
Stefan Agner
5519194d4f mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-05-24 14:27:28 -05:00
Stefan Agner
84d656a283 mtd: vf610_nfc: use in-band bad block table
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:55 -05:00
Stefan Agner
5dec286b82 mtd: vf610_nfc: implement OOB only read
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
  size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
  the special handling of OOB (spareonly).

Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:55 -05:00
Stefan Agner
d111bf99a8 mtd: vf610_nfc: allow bitflips in an empty page
Allow bit flips in a empty page up to half of the recoverable
bits (strength / 2).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Stefan Agner
6fcfd1e890 mtd: vf610_nfc: remove read on SEQIN
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.

However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Stefan Agner
f55bc296a8 mtd: vf610_nfc: remove caching of page in buffer
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.

Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Jörg Krause
1fbdb70610 mtd: nand: mxs: Replace magic number for bits per ECC level with macro
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-05-24 14:26:54 -05:00
Peng Fan
bd38da1a55 mtd:mxs:nand calculate ecc strength dynamically
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2015-05-24 14:26:54 -05:00
Raghav Dogra
6b8583b0ad nand/elbc: Memory leak fix
Freeing allocated memory to priv before returning
from the function

Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-05-22 15:45:51 -05:00
Stephen Warren
5e856fa8be nand: fix buffer alignment in new verification feature
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.

This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).

I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.

Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-05-21 14:24:36 -05:00
Scott Wood
b2d5ac5985 armv8/ls2085aqds: NAND boot support
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.

Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Jaiprakash Singh
39b0bbbb23 driver/ifc: Add 64KB page support
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.

FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.

Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Scott Wood
585acc9de6 nand/fsl_ifc: Increase eccstat[] for IFC 2.0
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers.  Fix the resulting array overflow.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:53 -07:00
Albert ARIBAUD \(3ADEV\)
c8381bf435 lpc32xx: mtd: nand: add MLC NAND controller
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.

The SPL framework is supported.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:56 +02:00
Tom Rini
10697704ca Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-03-31 19:15:59 -04:00
David Dueck
da78fb5414 ARM: at91: atmel_nand: Support flash based BBT
Add support for on-flash bad block table. This makes U-Boot handle an existing
BBT correctly.

Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
2015-04-01 01:04:28 +02:00
Stefan Agner
55765b1842 mtd: vf610_nfc: specify transfer size before each transfer
Testing showed, that commands like STATUS made the buffer dirty
when executed with NFC_SECSZ set to the page size. It looks
like the controller transfers bogus data when this register
is configured. When setting it to 0, the buffer does not get
altered while the status command still seems to work flawless.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-03-30 23:35:27 -05:00
Stefan Agner
7653fc288a mtd: vf610_nfc: mark page as dirty on block erase
The driver tries to re-use the page buffer by storing the page
number of the current page in the buffer. The page is only read
if the requested page number is not currently in the buffer. When
a block is erased, the page number is marked as invalid if the
erased page equals the one currently in the cache. However, since
a erase block consists of multiple pages, also other page numbers
could be affected.

The commands to reproduce this issue (on a written page):
> nand dump 0x800
> nand erase 0x0 0x20000
> nand dump 0x800

The second nand dump command returns the data from the buffer,
while in fact the page is erased (0xff).

Avoid the hassle to calculate whether the page is affected or not,
but set the page buffer unconditionally to invalid instead.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-03-30 23:33:42 -05:00
Peter Tyser
004a1fdb45 nand: yaffs: Remove the "nand write.yaffs" command
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years.  If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling.  This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.

U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2015-03-30 23:24:39 -05:00
Peter Tyser
073adf987e nand: Remove CONFIG_MTD_NAND_VERIFY_WRITE
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:39 -05:00
Peter Tyser
59b5a2ad83 nand: Add verification functions
Add nand_verify() and nand_verify_page_oob().  nand_verify() verifies
NAND contents against an arbitrarily sized buffer using ECC while
nand_verify_page_oob() verifies a NAND page's contents and OOB.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:38 -05:00
Luca Ellero
88a2cbb2ae mtd: nand: mxs: fix PIO_WORDs in mxs_nand_write_buf()
There is only one pio_word in this DMA transaction so data field must be 1.

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
2015-03-30 22:25:54 -05:00
Luca Ellero
5263a02e8b mtd: nand: mxs: fix PIO_WORDs in mxs_nand_read_buf()
There is only one pio_word in this DMA transaction so data field must be 1.

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
2015-03-30 22:25:47 -05:00
Ash Charles
b050898efa omap: gpmc: 'nandecc sw' can use HAM1 or BCH8
The 'nandecc sw' command selects a software-based error correction
algorithm.  By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm.  Allow a user to be specific e.g.
 # nandecc sw <hamming|bch8>
where 'hamming' is still the default.

Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
      to a hardware-based ECC scheme---a little strange when the user
      has requested 'sw' ECC.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
2015-03-05 20:49:43 -05:00
Michal Sojka
d8af39337e mtd: nand: omap_gpmc: Make ready/busy pins configurable
Commit fb384c4720 introduced the use of
WAIT0 pin for determining whether the NAND is ready or not. This only
works if all NAND chips are connected to WAIT0. If some chips are
connected to the other available pin WAIT1, nand_wait() does not really
wait and prints a WARN_ON message.

This patch allows the board to provide configuration of which chip is
connected to which WAITx signal. For example, one can define in
include/configs/foo.h:

    #define CONFIG_NAND_OMAP_GPMC_WSCFG     0,0,1,1

This would mean that chips using to CS0 and 1 are connected to WAIT0 and
chips with CS2 and 3 are connected to WAIT1.

Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Vokáč <michal.vokac@comap.cz>

Cc: Tom Rini <trini@ti.com>
2015-03-05 20:49:42 -05:00
Masahiro Yamada
d648964fc2 kconfig: remove unneeded dependency on !SPL_BUILD
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-24 17:06:27 -05:00
Masahiro Yamada
e02ee2548a kconfig: switch to single .config configuration
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL).  There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.

It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:

[1] It is impossible to share CONFIG options across the images.
  If you change the configuration of Main image, you often have to
  adjust some SPL configurations correspondingly.  Currently, we
  cannot handle the dependencies between them.  It means one of the
  biggest advantages of Kconfig is lost.

[2] It is too painful to change both ".config" and "spl/.config".
  Sunxi guys started to work around this problem by creating a new
  configuration target.  Commit cbdd9a9737 (sunxi: kconfig: Add
  %_felconfig rule to enable FEL build of sunxi platforms.) added
  "make *_felconfig" to enable CONFIG_SPL_FEL on both images.
  Changing the configuration of multiple images in one command is a
  generic demand.  The current implementation cannot propose any
  good solution about this.

[3] Kconfig files are getting ugly and difficult to understand.
  Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
  Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.

[4] The build system got more complicated than it should be.
  To adjust Linux-originated Kconfig to U-Boot, the helper script
  "scripts/multiconfig.sh" was introduced.  Writing a complicated
  text processor is a shell script sometimes caused problems.

Now I believe the "single .config" will serve us better.  With it,
all the problems above would go away.  Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much.  Anyway, this is what we do now in
scripts/Makefile.spl.

I admit my mistake with my apology and this commit switches to the
single .config configuration.

It is not so difficult to do that:

 - Remove unnecessary processings from scripts/multiconfig.sh
  This file will remain for a while to support the current defconfig
  format.  It will be removed after more cleanups are done.

 - Adjust some makefiles and Kconfigs

 - Add some entries to include/config_uncmd_spl.h and the new file
   scripts/Makefile.uncmd_spl.  Some CONFIG options that are not
   supported on SPL must be disabled because one .config is shared
   between SPL and U-Boot proper going forward.  I know this is not
   a beautiful solution and I think we can do better, but let's see
   how much we will have to describe them.

 - update doc/README.kconfig

More cleaning up patches will follow this.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-24 17:06:23 -05:00
Egli, Samuel
89831112d4 mtd, omap: fix case NAND_OMAP_GPMC_PREFETCH not defined
The patch c316f577b4 breaks
siemens boards because prefetch mode is not enabled.
I assume it breaks other boards as well that don't use
prefetch.

This patch sets read_buf to nand_read_buf if
NAND_OMAP_GPMC_PREFETCH is not defined.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
CC: Daniel Mack <zonque@gmail.com>
CC: Guido Martínez <guido@vanguardiasur.com.ar>
CC: Tom Rini <trini@ti.com>
CC: Heiko Schocher <hs@denx.de>
2015-02-16 12:41:40 -05:00
Wu, Josh
0e48dc5e41 mtd: atmel_nand: according to pmecc version to perform 0xff page correction
As the PMECC hardware has different version. In SAMA5D4 chip, the PMECC ip
can generate 0xff pmecc ECC value for all 0xff sector.

According to this, add PMECC version check, if it's SAMA5D4 then we always
let PMECC hardware to correct it.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07 23:42:57 +01:00
Simon Glass
b0265d56fe dm: tegra: nand: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Masahiro Yamada
5344cc1a82 powerpc: ppc4xx: remove PPChameleonEVB, CATcenter boards
These boards are still non-generic boards.

It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
2015-01-23 16:53:36 -05:00
Daniel Mack
c316f577b4 mtd: OMAP: Enable GPMC prefetch mode
Enable GPMC's prefetch feature for NAND access. This speeds up NAND read
access a lot by pre-fetching contents in the background and reading them
through the FIFO address.

The current implementation has two limitations:

 a) it only works in 8-bit mode
 b) it only supports read access

Both is easily fixable by someone who has hardware to implement it.

Note that U-Boot code uses non word-aligned buffers to read data into, and
request read lengths that are not multiples of 4, so both partial buffers
(head and tail) have to be addressed.

Tested on AM335x hardware.

Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Daniel Mack <zonque@gmail.com>
[trini: Make apply again, use 'cs' fix pointed out by Guido]
Signed-off-by: Tom Rini <trini@ti.com>
2015-01-13 11:51:23 -05:00
Masahiro Yamada
ab37b76d5d mtd: nand: do not scan BBT after scrub
Currently, "nand scrub" runs chip->scan_bbt at the end of
nand_erase_opts() even if NAND_SKIP_BBTSCAN flag is set.

It violates the intention of NAND_SKIP_BBTSCAN.

Move NAND_SKIP_BBTSCAN flag check to nand_block_checkbad() so that
chip->scan_bbt() is never run if NAND_SKIP_BBTSCAN is set.

Also, unset NAND_BBT_SCANNED flag instead of running chip->scan_bbt()
right after scrub.  We can be lazier here because the BBT is scanned
at the next call of nand_block_checkbad().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
2015-01-09 12:19:06 -06:00
Masahiro Yamada
bf80ee6e1d mtd: nand: Mark the BBT as scanned prior to calling scan_bbt again
Commit 35c204d8a9 (nand: reinstate lazy bad block scanning)
broke NAND_BBT_USE_FLASH feature.

Its git-log claimed that it reinstated the change as by commit
fb49454b1b ("nand: reinstate lazy bad block scanning"), but it moved
"chip->options |= NAND_BBT_SCANNED" below "chip->scan_bbt(mtd);".

It causes recursion if scan_bbt does not find a flash based BBT
and tries to write one, and the attempt to erase the BBT area
causes a bad block check.

Reinstate commit ff49ea8977 (NAND: Mark the BBT as scanned prior to
calling scan_bbt.).

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rostislav Lisovy <lisovy@merica.cz>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
2015-01-09 12:19:02 -06:00
Masahiro Yamada
756963d7da mtd: nand: revive "nand scrub" command
Since commit ff94bc40af (mtd, ubi, ubifs: resync with Linux-3.14),
the "nand scrub" command has not been working.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2015-01-09 12:18:58 -06:00
Guido Martínez
eb54d2c70c mtd: nand: omap_gpmc: fix error handling
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).

In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.

Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-01-05 16:40:18 -05:00
Jaiprakash Singh
1d421cc677 driver/mtd: Fix IFC compilation warnings
'eccstat' array elements might be used uninitialized

Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:42:32 -08:00
Alison Wang
8ab967b6c6 arm: ls102xa: Add NAND boot support for LS1021AQDS board
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:40:24 -08:00
Stefan Roese
fb384c4720 mtd: nand: omap_gpmc: Always use ready/busy pin
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.

Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:

Without NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.947 seconds, 2947 ticks

With NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.795 seconds, 2795 ticks

So an increase of approx. 5%.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
2014-12-04 21:28:31 -05:00
Marek Vasut
b19157bf3f mtd: nand: s3c: Unify the register definition and naming
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
2014-11-26 23:21:43 -06:00
Sanchayan Maity
2260457341 mtd/nand/vf610_nfc: Disable subpage writes
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.

Patch has been tested on a Colibri VF61 module.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2014-11-26 19:53:49 -06:00
Masahiro Yamada
f09eb52b3f mtd: denali: set some registers after nand_scan_ident()
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc.  Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices.  The device parameters detected
during nand_scan_ident() are more trustworthy.

This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
2014-11-26 19:53:22 -06:00
Masahiro Yamada
65e4145a20 mtd: denali: use CONFIG_SYS_NAND_SELF_INIT
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().

CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail().  It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux.  Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
2014-11-26 19:53:19 -06:00
Rostislav Lisovy
35c204d8a9 nand: reinstate lazy bad block scanning
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").

Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
2014-11-26 19:51:51 -06:00
Masahiro Yamada
b41411954d linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does.  This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
 - Use min, max, min3, max3 only when the arguments have the same type
   (or add casts to the arguments)
 - Use min_t/max_t instead with the appropriate type for the first
   argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-23 06:48:30 -05:00
Josh Wu
7df4486d04 mtd: atmel_nand: runtime to build gf table for pmecc
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.

The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:18 -05:00
Heiko Schocher
667af36905 spl, mtd, nand, atmel_nand: invert device ready pin logic
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Heiko Schocher
4dfd360589 spl, nand, atmel_nand: add erase one block function
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Heiko Schocher
c1ec406282 mtd: atmel_nand: add missing include
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Tom Rini
625509ab0e Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-11-05 12:48:09 -05:00
Marek Vasut
f9cfe17b3d mtd: nand: mxs: Add ECC geometry for 2048b/112b NAND
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-30 11:02:23 +01:00
Jeroen Hofstee
441529795c omap_gpmc: fix warnigs with W=1
- make omap_spl_dev_ready static
- make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25 07:02:02 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Albert ARIBAUD
790af81543 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-10-11 01:20:30 +02:00
Masahiro Yamada
ed3c980bee mtd: denali: support NAND_CMD_RNDOUT command
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported.  It is necessary to detect some
types of ONFi-compliant devices.  Without it, the error message
"unsupported command received 0x5" is shown.

Let's support this command on the Denali NAND controller driver.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-09 17:33:26 -05:00
Masahiro Yamada
05968e7cfd mtd: denali: fix NAND_CMD_PARAM command
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.

Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.

In addition, unnecessary clear_interrupts() should be removed.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-09 17:33:24 -05:00
Albert ARIBAUD
4b19b7448e Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.

Conflicts:
	board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08 21:20:49 +02:00
Masahiro Yamada
845034e6b2 mtd: denali: add Denali NAND driver for SPL
The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP.

This driver requires two CONFIG macros:
 - CONFIG_SPL_NAND_DENALI
     Define to enable this driver.
 - CONFIG_SYS_NAND_BAD_BLOCK_POS
     Specify bad block mark position in the oob space. Typically 0.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-10-05 14:10:09 +09:00
Masahiro Yamada
4b0abf9f3c mtd: denali: add Denali controller configs to Kconfig
Commit 3eb3e72a3f (nand/denali: Adding Denali NAND driver support)
introduced some new options, and some of them were documented by
commit f9860cf081 (nand/denali: Document CONFIG symbols).

This commit allows users to enable/disable them via Kconfig
with more detailed help docs.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-10-05 14:10:09 +09:00
Tom Rini
2c2277f15c Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2014-09-26 09:57:52 -04:00
Chin Liang See
3eb3e72a3f nand/denali: Adding Denali NAND driver support
To add the Denali NAND driver support into U-Boot.
This driver is leveraged from Linux with commit ID
fdbad98dff8007f2b8bee6698b5d25ebba0471c9. For Denali
controller 64 variance, you need to declare macro
CONFIG_SYS_NAND_DENALI_64BIT.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25 13:43:16 -05:00
Stefan Roese
be16aba5ce mtd: nand: Fix length bug in ioread16_rep() and iowrite16_rep()
The ioread16_rep() and iowrite16_rep() implementations are U-Boot specific
and have been introduced with the Linux MTD v3.14 sync. While introducing
these functions, the length for the loop has been miscalculated. The ">> 1"
is already present in the caller. So lets remove it in the function.

Tested on omap3_ha.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-09-25 13:43:00 -05:00
Rostislav Lisovy
2f665945b3 mtd: nand: am335x: Fix 'bit-flip' errors in SPL
OMAP GPMC driver used with some NAND Flash devices
(e.g. Spansion S34ML08G1) causes that U-boot shows
hundreds of 'nand: bit-flip corrected' error messages.
Possible cause was discussed in the mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html

The issue was partially fixed with the cc81a5291910d7a.git
however this has to be done to fix the SPL.

The original author of the code is Belisko Marek
<marek.belisko@gmail.com>

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-25 13:43:00 -05:00
Prabhakar Kushwaha
5b8388a827 driver/mtd: Use generic timer API for FSL IFC, eLBC
Freescale's flash control driver is using architecture specific timer API
i.e. usec2ticks

Replace usec2ticks with get_timer() (generic timer API)

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-25 08:36:17 -07:00
Stefano Babic
42817eb85d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-22 15:51:01 +02:00
Boris BREZILLON
d357b94041 mtd: atmel_nand: Disable subpage NAND write when using Atmel PMECC
Disable subpage write when using PMECC to prevent buggy partial page write.

This fix has been taken from linux sources (see commit
90445ff6241e2a13445310803e2efa606c61f276)

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:22 +02:00
Wu, Josh
14b3b44eda mtd: atmel-nand: use pmecc_readl(b)/pmecc_writel to access the pmecc register
We defined the macro pmecc_readl(b)/pmecc_writel for pmecc register access.
But in the driver we also use the readl(b)/writel.
To keep consistent, this patch make all use pmecc_readl(b)/pmecc_writel.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:13 +02:00
Khoronzhuk, Ivan
7206111e52 mtd: nand: davinci_nand: update write_page function for keystone RBL
After mtd was synced with Linux 3.14
(ff94bc40af)
the number of parameters for write_page function of nand_chip was
changed. The additional two var were needed for subpage write.
As keystone has no supbage write they are not needed. So correct
only function definition by upgrading it's parameter list.
That helps to get ritd of compilation warning.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-16 12:23:59 -04:00
Masahiro Yamada
3b61297024 kbuild: force to define __UBOOT__ in all the C sources
U-Boot has imported various source files from other projects,
mostly Linux.

Something like

  #ifdef __UBOOT__
    [ modification for U-Boot ]
  #else
    [ original code ]
  #endif

is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.

Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2014-09-16 12:23:56 -04:00
Stefan Agner
72d7beabf7 mtd: nand: add Freescale vf610_nfc driver
This adds initial support for Freescale NFC (NAND Flash Controller)
found in ARM Vybrid SoC's, Power Architecture MPC5125 and others.
The driver is called vf610_nfc since this is the first supported
and tested hardware platform supported by the driver.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
2014-09-16 13:25:18 +02:00
Rostislav Lisovy
cc81a52919 mtd: nand: omap_gpmc: Fix 'bit-flip' errors
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion
S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip
corrected' error messages. Possible cause was discussed in the
mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html

Quote (Author: Pekon Gupta <pekon@ti.com>): "The issue is mainly
due to a NAND protocol violation in the omap driver since the
Random Data Output command (05h-E0h) expects to see only the
column address that should be addressed within the already loaded
read page into the read buffer. Only 2 address cycles with ALE
active should be provided between the 05h and E0h commands. The
Page read command expects the full address footprint (2bytes for
column address + 3bytes for row address), but once the page is
loaded into the read buffer, Random Data Output should be used
with only 2bytes for column address."

This patch combines the solution proposed in the mailinglist and
the patch provided by the Spansion company (GPLv2 code, source:
http://www.spansion.com/Support/Software/u-boot-psp-04.04.00.01-NAND.zip)

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04 13:06:00 -04:00
Rostislav Lisovy
5c3f7e0ead mtd: nand: omap_gpmc: Enable multiple NAND flash devices
Since the CS of a device connected to the GPMC was
stored in the global variable, it was not possible to
use multiple devices. In this patch the CS is stored per
device in its 'struct omap_nand_info'. This makes it
possible to use up to 'GPMC_MAX_CS' NAND Flash devices
connected to U-boot.

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04 13:06:00 -04:00
Khoronzhuk, Ivan
fc12a1f589 mtd: nand: davinci_nand: correct keystone RBL layout definition
In case when 4K page keystone RBL layout is used the compilation
error is appeared. That's because the #ifdef has to be placed under
struct name. This patch correct it.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-04 13:06:00 -04:00
Holger Brunck
292221e183 arm/kirkwood/nand: allow forced disabling for subpage writes
Make it configurable to disable subpage writes like the DaVinci NAND
driver already does.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Scott Wood <scottwood@freescale.com>
2014-08-30 07:46:41 -04:00
Heiko Schocher
4e67c57125 mtd,ubi,ubifs: sync with linux v3.15
snyc with linux v3.15:

commit 1860e379875dfe7271c649058aeddffe5afd9d0d
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Jun 8 11:19:54 2014 -0700

    Linux 3.15

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
2014-08-25 19:25:56 -04:00
Heiko Schocher
ff94bc40af mtd, ubi, ubifs: resync with Linux-3.14
resync ubi subsystem with linux:

commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Mar 30 20:40:15 2014 -0700

    Linux 3.14

A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
2014-08-25 19:25:55 -04:00
Tom Rini
362f16b1e9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-07-29 09:41:35 -04:00
Khoronzhuk, Ivan
67ac6ffaee mtd: nand: davinci: add opportunity to write keystone U-boot image
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.

The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.

The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.

Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 15:21:06 -04:00
Prabhakar Kushwaha
591dd19230 driver/nand: Add support of 16K SRAM for IFC 2.0
Internal SRAM has been incresed from 8KB to 16KB for IFC cotroller ver 2.0.

Update the page offset calculation logic to support the same.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Prabhakar Kushwaha
04818bbdc3 driver/nand: Update SRAM initialize logic for IFC.
IFC controller v1.1.0 requires internal SRAM initialize by reading
NAND flash. Higher controller versions have provided "SRAM init" bit in
NCFGR register space.

update SRAM initialize logic to reflect the same.

Also print error message in case of Page read error.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Prabhakar Kushwaha
3bab3d8324 driver/nand:Define MAX_BANKS same as SoC defined for IFC
The number of chip select used by IFC controller vary from one SoC to other.
For eg. P1010 has 4, T4240 has 8.

Update MAX_BANKS same as SoC defined

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Albert ARIBAUD
d6694aff56 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-06-30 23:00:34 +02:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
pekon gupta
46840f66ca mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
This patch add support for BCH16_ECC to omap_gpmc driver.

*need to BCH16 ECC scheme*
With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes
Flash devices have become more suspectible to bit-flips. Thus stronger
ECC schemes are required for protecting the data.
But stronger ECC schemes have come with larger-sized ECC syndromes which require
more space in OOB/Spare. This puts constrains like;
(a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data.
(b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy following equation:
OOBsize per page >= 26 * (page-size / 512)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:10 -04:00
pekon gupta
b80a660338 mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:06 -04:00
Brian Norris
27ce9e4290 mtd: nand: force NAND_CMD_READID onto 8-bit bus
As per following Sections in ONFI Spec, NAND_CMD_READID should use only
lower 8-bit for transfering command, address and data even on x16 NAND device.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

Thus porting  following commit from linux-kernel to ensure that column address
is not altered to align to x16 bus when issuing NAND_CMD_READID command.

    commit 3dad2344e92c6e1aeae42df1c4824f307c51bcc7
    mtd: nand: force NAND_CMD_READID onto 8-bit bus
    Author: Brian Norris <computersforpeace@gmail.com> (preserving authorship)

    The NAND command helpers tend to automatically shift the column address
    for x16 bus devices, since most commands expect a word address, not a
    byte address. The Read ID command, however, expects an 8-bit address
    (i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
    0x20).

    This fixes the column address for a few drivers which imitate the
    nand_base defaults.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:03 -04:00
Brian Norris
b9ae609fdb mtd: nand: don't use read_buf for 8-bit ONFI transfers
Porting below commit from linux-tree, preserving original authorship & commit log
commit bd9c6e99b58255b9de1982711ac9487c9a2f18be
Author:     Brian Norris <computersforpeace@gmail.com>
mtd: nand: don't use read_buf for 8-bit ONFI transfers

  Use a repeated read_byte() instead of read_buf(), since for x16 buswidth
  devices, we need to avoid the upper I/O[16:9] bits. See the following
  commit for reference:

  commit 05f7835975dad6b3b517f9e23415985e648fb875 (from linux-tree)
  Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
  Date:   Thu Dec 5 22:22:04 2013 +0100

      mtd: nand: don't use {read,write}_buf for 8-bit transfers

  Now, I think that all barriers to probing ONFI on x16 devices are
  removed, so remove the check from nand_flash_detect_onfi().

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:01 -04:00
pekon gupta
3f990dc83b mtd: nand: omap: fix error-codes returned from omap-elm driver
This patch
 omap-elm.c: replaces -ve integer value returned during errorneous condition,
             with proper error-codes.
 omap-gpmc.c: updates omap-gpmc driver to pass error-codes returned from
             omap-elm driver to upper layers

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:46:00 -04:00
pekon gupta
a09431da38 mtd: nand: omap_gpmc: minor cleanup of omap_correct_data_bch
This patch tries to avoid some local pointer dereferences, by using common
local variables in omap_correct_data_bch()

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:57 -04:00
pekon gupta
9233279f8e mtd: nand: omap_gpmc: rename struct nand_bch_priv to struct omap_nand_info
This patch renames 'struct nand_bch_priv' which currently holds private data only
for BCH ECC schemes, into 'struct omap_nand_info' so that same can be used for
all ECC schemes

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:55 -04:00
pekon gupta
d21e77ff84 mtd: nand: omap_gpmc: remove unused members of 'struct nand_bch_priv'
This patch prepares to refactor 'struct nand_bch_priv' -> 'struct omap_nand_info'
And thus performs following clean-ups:
 - remove nand_bch_priv.type: use nand_bch_priv.ecc_scheme instead
 - remove nand_bch_priv.mode: <unused>

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:51 -04:00
pekon gupta
41bbe4dd49 mtd: nand: omap_elm: use bch_type instead of nibble count to differentiate between BCH4/BCH8/BCH16
ELM hardware engine support ECC error detection for multiple ECC strengths like
 +------+------------------------+
 |Type  | ECC syndrome length    |
 +------+------------------------+
 |BCH4  | 6.5 bytes = 13 nibbles |
 |BCH8  | 13 byte = 26 nibbles   |
 |BCH16 | 26 bytes = 52 nibbles  |
 +------+------------------------+

Current implementation of omap_elm driver uses ECC syndrom length (in 'nibbles')
to differentiate between BCH4/BCH8/BCH16. This patch replaces it with 'bch_type'

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:48 -04:00
pekon gupta
b98c5755c0 mtd: nand: omap_elm: remove #include omap_gpmc.h
There is no dependency of omap_elm.c on omap_gpmc.h

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:47 -04:00
Tim Harvey
73210dccdb spl: nand: add support for mxs nand
This utilizes existing mxs_nand support layer to provide a method to load an
image off nand for SPL. The flash device will be detected in order to support
multiple flash devices instead of having layout hard coded at build time.

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:07:25 +02:00
Belisko Marek
97eeae1a07 mtd: nand: omap_gpmc: Fix update of read_ecc in oob
We need to flip only one bit not assign.

Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
2014-05-13 19:48:17 -04:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Prabhakar Kushwaha
5abed9c546 driver/ifc: define nand_spl_load_image() for SPL
nand_spl_load_image() can also be used for non TPL framework.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:50 -07:00
Karicheri, Muralidharan
999d7d326d NAND: DaVinci: allow forced disable of subpage writes
This patch introduces a configurable mechanism to disable
subpage writes in the DaVinci NAND driver.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
db60580649 mtd: Build nand_util.o for CONFIG_ENV_IS_IN_NAND in SPL
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
6dd3b56689 mtd: Add a CONFIG_SPL_MTD_SUPPORT for a more full NAND subsystem in SPL
This mainly converts the am335x_spl_bch driver to the "normal" format
which means a slight change to nand_info within the driver.

Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Masahiro Yamada
dd649f1d00 mtd: delete unused files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-04-17 14:38:30 -04:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Bo Shen
0b0b4f5981 mtd: nand: atmel: prepare for nand spl boot support
Prepare for nand spl boot support. It supports nand software ECC and
hardware PMECC.
This patch is take <drivers/mtd/nand/nand_spl_simple.c> as reference.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:19:06 +01:00
Stefan Roese
345b77baca ppc4xx: Remove 4xx NAND booting support
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.

This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2014-03-07 10:59:06 -05:00
pekon gupta
2eda892f00 mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
6aff050988 mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
51d192c40d mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
6e562b1106 mtd: nand: omap: optimized chip->ecc.correct() for H/W ECC schemes
chip->ecc.correct() is used for detecting and correcting bit-flips during read
operations. In omap-nand driver it implemented as:
(a) omap_correct_data(): for h/w based ECC_HAM1 scheme
(b) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
	for ECC_BCH8 scheme using GPMC and software lib/bch.c
(c) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW
	for ECC_BCH8 scheme using GPMC and ELM

This patch updates (c)
- checks for calc_ecc[]==0x00 so that error_correction is not required for
  known good pages.
- adds scalability for other ECC_BCHx scheme by merging following
  omap_rotate_ecc_bch() + omap_fix_errors_bch() => omap_correct_data_bch()
- fixing logic for bit-flip correction based on error_loc[count]

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-03 20:09:03 -06:00
pekon gupta
71a7f95600 mtd: nand: omap: optimize chip->ecc.calculate() for H/W ECC schemes
chip->ecc.calculate() is used for calculating and fetching of ECC syndrome by
processing the data passed during Read/Write accesses.

All H/W based ECC schemes use GPMC controller to calculate ECC syndrome.
But each BCHx_ECC scheme has its own implemetation of post-processing and
fetching ECC syndrome from GPMC controller.

This patch updates OMAP_ECC_BCH8_CODE_HW ECC scheme in following way:
- merges multiple chip->calculate API for different ECC schemes
  omap_calculate_ecc() + omap_calculate_ecc_bch() + omap_calculate_ecc_bch_sw()
				==> omap_calculate_ecc()
- removes omap_ecc_disable() and instead uses it as inline.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-03 20:09:03 -06:00
pekon gupta
f5f1f614bd mtd: nand: omap: optimize chip->ecc.hwctl() for H/W ECC schemes
chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)

Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()

(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-03 20:09:03 -06:00
Prabhakar Kushwaha
1b4175d6fa driver/ifc:Change accessor function to take care of endianness
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.

So update acessor functions with common IFC acessor functions to take care
both type of endianness.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:51 -08:00
Po Liu
6609916efb powerpc:mpc85xx: Add ifc nand boot support for TPL/SPL
Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.

	- For ifc, elbc, esdhc, espi, all need the SPL without
	section .resetvec.
	- Use a clear function name for nand spl boot.
	- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
	in spl/Makefile;

Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:42:01 -08:00
Jeroen Hofstee
13fbde6e4f nand, gpmc: fix reading after switching ecc
The omap_gpmc allows switching ecc at runtime. Since
the NAND_SUBPAGE_READ flag is only set, it is kept when
switching to hw ecc, which is not correct. This leads to
calling chip->ecc.read_subpage which is not a valid
pointer. Therefore clear the flag when switching ecc so
reading in hw mode works again.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-01-17 08:04:32 -05:00
Nikita Kiryanov
fcd0524574 mtd: nand: omap: fix ecc ops assignment when changing ecc
If we change to software ecc and then back to hardware ecc, the nand ecc ops
pointers are populated with incorrect function pointers. This is related to the
way nand_scan_tail() handles assigning functions to ecc ops:

If we are switching to software ecc/no ecc, it assigns default functions to the
ecc ops pointers unconditionally, but if we are switching to hardware ecc,
the default hardware ecc functions are assigned to ops pointers only if these
pointers are NULL (so that drivers could set their own functions). In the case
of omap_gpmc.c driver, when we switch to sw ecc, sw ecc functions are
assigned to ecc ops by nand_scan_tail(), and when we later switch to hw ecc,
the ecc ops pointers are not NULL, so nand_scan_tail() does not overwrite
them with hw ecc functions.
The result: sw ecc functions used to write hw ecc data.

Clear the ecc ops pointers in omap_gpmc.c when switching ecc types, so that
ops which were not assigned by the driver will get the correct default values
from nand_scan_tail().

Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-12-17 17:47:47 -06:00
Nikita Kiryanov
eb237a15bd mtd: nand: omap: fix sw->hw->sw ecc switch
When switching ecc mode, omap_select_ecc_scheme() assigns the appropriate values
into the current nand chip's ecc.layout struct. This is done under the
assumption that the struct exists only to store values, so it is OK to overwrite
it, but there is at least one situation where this assumption is incorrect:

When switching to 1 bit hamming code sw ecc, the job of assigning layout data
is outsourced to nand_scan_tail(), which simply assigns into ecc.layout a
pointer to an existing struct prefilled with the appropriate values. This struct
doubles as both data and layout definition, and therefore shouldn't be
overwritten, but on the next switch to hardware ecc, this is exactly what's
going to happen. The next time the user switches to software ecc, they're
going to get a messed up ecc layout.

Prevent this and possible similar bugs by explicitly using the
private-to-omap_gpmc.c omap_ecclayout struct when switching ecc mode.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-12-17 17:46:53 -06:00
Tom Rini
3ef1eadb44 nand_util.c: Use '%zd' for length in nand_unlock debug print
length is size_t so needs to be '%zd' not '%d' to avoid warnings.

Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-17 17:44:36 -06:00
Nikita Kiryanov
2528460c38 mtd: nand: omap: fix HAM1_SW ecc using default value for ecc.size
Commit "mtd: nand: omap: enable BCH ECC scheme using ELM for generic
platform" (d016dc42ce) changed the way
software ECC is configured, both during boot, and during ecc switch, in a way
that is not backwards compatible with older systems:

Older version of omap_gpmc.c always assigned ecc.size = 0 when configuring
for software ecc, relying on nand_scan_tail() to select a default for ecc.size
(256), while the new version of omap_gpmc.c assigns ecc.size = pagesize,
which is likely to not be 256.

Since 1 bit hamming sw ecc is only meant to be used by legacy devices, revert
to the original behavior.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Pekon Gupta <pekon@ti.com>
2013-12-17 17:41:25 -06:00
Stefan Roese
5d7a49b930 mtd: nand: omap_gpmc: cosmetic: Fix indentation
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: wrap some long lines]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-12-17 17:31:14 -06:00
pekon gupta
69cc97f8db mtd: nand: omap: fix ecc-layout for HAM1 ecc-scheme
As per OMAP3530 TRM referenced below [1]

For large-page NAND, ROM code expects following ecc-layout for HAM1 ecc-scheme
 - OOB[1] (offset of 1 *byte* from start of OOB) for x8 NAND device
 - OOB[2] (offset of 1 *word* from start of OOB) for x16 NAND device

Thus ecc-layout expected by ROM code for HAM1 ecc-scheme is:
 *for x8 NAND Device*
 +--------+---------+---------+---------+---------+---------+---------+
 | xxxx   | ECC[A0] | ECC[A1] | ECC[A2] | ECC[B0] | ECC[B1] | ECC[B2] | ...
 +--------+---------+---------+---------+---------+---------+---------+

 *for x16 NAND Device*
 +--------+--------+---------+---------+---------+---------+---------+---------+
 | xxxxx  | xxxxx  | ECC[A0] | ECC[A1] | ECC[A2] | ECC[B0] | ECC[B1] | ECC[B2] |
 +--------+--------+---------+---------+---------+---------+---------+---------+

This patch fixes ecc-layout *only* for HAM1, as required by ROM-code
For other ecc-schemes like (BCH8) ecc-layout is same for x8 or x16 devices.

[1] OMAP3530: http://www.ti.com/product/omap3530
    TRM: http://www.ti.com/litv/pdf/spruf98x
		Chapter-25: Initialization Sub-topic: Memory Booting
		Section: 25.4.7.4 NAND
		Figure 25-19. ECC Locations in NAND Spare Areas

Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Stefan Roese <sr@denx.de>
2013-12-17 17:28:41 -06:00
Masahiro Yamada
392ba5256a drivers/mtd: descend into sub directories only when it is necessary
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-13 09:18:44 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Andreas Bießmann
ac45bb1646 at91: nand: switch atmel_nand to generic GPIO API
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2013-12-09 13:21:45 +01:00
Tom Rini
77fdd6d1eb Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2013-12-02 08:38:28 -05:00
York Sun
0b66513b27 Driver/IFC: Move Freescale IFC driver to a common driver
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:47 -08:00
pekon gupta
3f719069c8 mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.

1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
   other ecc-schemes also supported in hardware. like;
 - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
   the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
   software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
 - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
   supports BCH16 ecc-scheme also.

2) Different platforms use different CONFIG_xx to select ecc-schemes, which
   adds confusion for user while migrating platforms.
 - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
    8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
    whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
    and BCH16 (in future).
 - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
    correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
 - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library

Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
d016dc42ce mtd: nand: omap: enable BCH ECC scheme using ELM for generic platform
BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme                         | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW              |GPMC             |ELM H/W engine   |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC             |S/W BCH library  |
+-----------------------------------+-----------------+-----------------+

Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.

This patch
- removes CONFIG_AM33xx
	Thus this driver can be reused by all devices having ELM h/w engine.
- adds omap_select_ecc_scheme()
	A common function to handle ecc-scheme related configurations. This
	can be used both during device-probe and via user-space u-boot commads
	to change ecc-scheme. During device probe ecc-scheme is selected based
	on CONFIG_NAND_OMAP_ELM or CONFIG_NAND_OMAP_BCH8
- enables CONFIG_BCH
	S/W library (lib/bch.c) required by OMAP_ECC_BCHx_CODE_HW_DETECTION_SW
  	is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
	for auto-detection of ONFI compliant NAND devices
- updates following README doc
	doc/README.nand
	board/ti/am335x/README
	doc/README.omap3

Signed-off-by: Pekon Gupta <pekon@ti.com>
[scottwood@freescale.com: fixed unused variable warning]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Wu, Josh
c0dc3dec69 mtd: atmel_nand: use dev_xxx instead of printk
Signed-off-by: Josh Wu <josh.wu@atmel.com>
2013-11-21 13:33:41 -06:00
Wu, Josh
c55cc573ea mtd: atmel_nand: don't print bit correction message in driver
Since for some MLC nand, bit errors happened too often. Just disable it
to avoid noise

Signed-off-by: Josh Wu <josh.wu@atmel.com>
2013-11-21 13:33:41 -06:00
Wu, Josh
16dddef605 mtd: atmel_nand: enable PMECC support for 8k bytes page NAND flash
increase the delay to 75us to support the 8k bytes page nand flash

Signed-off-by: Josh Wu <josh.wu@atmel.com>
2013-11-21 13:33:41 -06:00
Prabhakar Kushwaha
71220f80e7 mtd/ifc: Add support of 8K page size NAND flash
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K NAND flash
  - Program Spare region size in csor_ext
  - Add nand_ecclayout for 4 bit & 8 bit ecc
  - Defines constants
  - Add support of 8K NAND boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Liu Po <po.liu@freescale.com>
2013-11-21 13:33:40 -06:00
Prabhakar Kushwaha
ed5ac34a33 driver/mtd/ifc: Read Status while programming NAND flash
as per controller description,
  "While programming a NAND flash, status read should never skipped.
   Because it may happen that a new command is issued to the NAND Flash,
   even when the device has not yet finished processing the previous request.
   This may result in unpredictable behaviour."

IFC controller never polls for R/B signal after command send. It just return
control to software. This behaviour may not occur with NAND flash access.
because new commands are sent after polling R/B signal. But it may happen
in scenario where GPCM-ASIC and NAND flash device are working simultaneously.

Update the controller driver to take care of this requirement

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-11-13 18:43:39 -06:00
Bo Shen
7604a3f920 MTD: atmel_nand: support for software BCH ECC
Add possible to use software BCH ECC for atmel nand driver

Signed-off-by: Bo Shen <voice.shen@gmail.com>
2013-11-13 17:20:26 -06:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Heiko Schocher
2fff63c2a5 nand, davinci: add special UBL ecc position
enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define

see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
2013-11-01 15:30:51 -04:00
Masahiro Yamada
2fc7ef6196 drivers: mtd: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:22:13 -04:00
Tom Rini
9d33fb4a5c nand_util.c: Correct licensing
Prior to SPDX licensing this file was GPL-2.0 with Freescale granting
rights for "or later" for their contributed code.  We incorrectly moved
this file to GPL-2.0+, so correct it to GPL-2.0.  In addition we cannot
easily denote in the file where or what code is "or later", so just set
that aside for now and the file as a whole is GPL-2.0 regardless.

Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-31 09:24:00 -04:00
Valentin Longchamp
2f9e559a6c mtd/fsl_elbc: take NAND_ECC_SOFT_BCH config option into account
NAND_ECC_SOFT was the only option available while the SOFT_BCH option
may also be used.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2013-10-24 09:36:05 -07:00
Wolfgang Denk
d4c8aa9cb4 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
93e1459641 Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14 16:06:54 -04:00
Paul Burton
40462e541d mtd: driver _read() returns max_bitflips; mtd_read() returns -EUCLEAN
Linux modified the MTD driver interface in commit edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.

For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:

  UBI DBG: ensure_wear_leveling: schedule scrubbing
  UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
  UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
  UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
  UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
  UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
  UBI: fixable bit-flip detected at PEB 1027
  UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
  UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
  UBI: fixable bit-flip detected at PEB 4083
  UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
  UBI DBG: erase_worker: erase PEB 4083 EC 55
  UBI DBG: sync_erase: erase PEB 4083, old EC 55
  UBI DBG: do_sync_erase: erase PEB 4083
  UBI DBG: sync_erase: erased PEB 4083, new EC 56
  UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
  UBI DBG: ensure_wear_leveling: schedule scrubbing
  UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
  ...

This patch adopts the interface change as in Linux commit edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
2013-10-09 12:52:04 -05:00
Elie De Brauwer
a8f2d0e675 mxs_nand: Fix ECC strength for NAND flash with OOB size of 224
On a board with an i.mx28 and a Micron MT29F4G08ABAEAH4, Linux says:

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAH4),
512MiB, page size: 4096, OOB size: 224) the ECC strength is 16.

root@(none):/sys/devices/virtual/mtd/mtd0# for i in ecc_strength oobsize subpagesize; do echo $i = `cat $i`; done
ecc_strength = 16
oobsize = 224
subpagesize = 4096

The ECC strength was not properly discovered by U-Boot causing the data
written by Linux to return an -74 (EBADMSG) when read from U-Boot. This
patch fixes mxs_nand_get_ecc_strength() to function in case of a NAND
flash with page_data_size = 4096 and page_oob_size= 224.

Signed-off-by: Elie De Brauwer <eliedebrauwer@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2013-09-11 09:33:36 +02:00
Wu, Josh
1bd3e2a823 mtd: atmel_nand: pmecc: fix bug fail to correct bit error in 1024-bytes sector
The PMECC use BCH algorithm to correct error. In BCH algorithm, the
primitive polynomial value is GF(2^13) for 512-bytes sector size. And it is
GF(2^14) for 1024-bytes sector size.

This patch will choose correct degree of the remainders (13 or 14) for
different sector size.
Tested in AT91SAM9X5-EK with MLC nand flash.

More detail can be refered to section 5.4.1 of:
  AT91SAM ARM-based Embedded MPU Application Note
  <http://www.atmel.com/Images/doc11127.pdf>

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-09-04 17:07:21 +02:00
Albert ARIBAUD
4eef93da26 Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-09-04 11:50:25 +02:00
Masahiro Yamada
47b6dad319 nand_util: delete a useless variable
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22 17:25:03 -05:00
Wu, Josh
a07d229497 ARM: at91: atmel_nand: add code to check the ONFI parameter ECC requirement
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
   ecc minimum requirement in ONFI parameter.

  a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
     Driver will display a WARNING if the values are different from ONFI
     parameters.

  b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
      the value from ONFI parameters.
      * If ONFI ECC parameters are in ONFI extended parameter page, since we
        are not support it, so assume the minimum ecc requirement is 2 bits
        in 512 bytes.
      * For non-ONFI support nand flash, also assume the minimum ecc
        requirement is 2 bits in 512 bytes.

2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
   and CONFIG_PMECC_SECTOR_SIZE.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:50:52 +02:00
Wu, Josh
ddd85974b1 mtd: atmel_nand: alloc memory instead of use static array for pmecc data
In this way, the pmecc corraction capbility can change in run time.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:50:44 +02:00
Wu, Josh
b2d96dc28f ARM: at91: atmel_nand: pmecc driver will select the galois table by sector size
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:50:16 +02:00
Ying Zhang
5d97fe2a04 powerpc: p1022ds: add TPL for p1022ds nand boot
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 09:57:51 -07:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Marek Vasut
1c90369437 mtd: mxc_nand: Fix crash after MTD resync
The driver triggered a BUG() in nand_base.c:3214/nand_scan_tail()
because the ecc.strength was not set in NAND_ECC_HW_SYNDROME ECC
mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-12 16:12:33 -05:00