Enable the QEMU firmware interface if ACPI tables are to be supported on
the QEMU platform.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a configuration fragment to enable ACPI on QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the QEMU firmware interface if ACPI tables are to be supported on
the QEMU platform.
Enable the QFW MMIO interface if the QEMU firmware interface is enabled.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
Unlike all other supported Tegra devices and most known Tegra devices, the
HTC One X has no hardware way to enter APX/RCM mode, which may lead to a
dangerous situation when, if BCT is set correctly and the bootloader is
faulty, the device will hang in a permanent brick state. Exiting from this
state can be done only by disassembling the device and shortening the
testpad to the ground.
To prevent this or to minimize the probability of such an accident, it was
proposed to add the RCM rebooting hook as early into SPL as possible since
SPL is much more robust and has minimal changes that can break bootflow.
gpio_early_init_uart() function was chosen as it is the earliest function
exposed for setup by the device. Hook performs a check for volume up button
state and triggers RCM if it is pressed.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Detect CPU name through marchid and then save it to env.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Kconfig provides SYS_[I|D]CACHE_OFF config options to switch off caches.
Provide the corresponding implementation to the options.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
variable was indented as part of the value of the previous variable.
Signed-off-by: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
In most cases, the architecture global data currently makes use of
assorted linux types, but does not include <linux/types.h> to provide
them. Add <linux/types.h> instead of relying on indirect inclusion.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
These files include <common.h> twice. Start by removing the second
inclusion of the file.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove and replace common.h and config.h in sandbox when it's not needed
and add some explicit includes where needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arm including config.h directly, but
add it where needed. This includes a few board-specific fixes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arc including config.h directly, but
add it where needed. Further clean up the tb100 board config.h file so
that we don't rely on config.h being included there for a value used in
a single place.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When som_type does not match any case, it is uninitialized and the
function still tries to print the SoM info. Rather, this is an error
condition and the function should abort prematurely. Highlight this by
printing an error message and returning early.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Move all function definitions in {phytec|imx8m}_som_detection from the
header to the source file to prevent potential linker error regarding
multiple definitions. Also move the #if blocks with the definitions.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
In phytec_eeprom_data_init, after reading eeprom data into buffer, it is
checked whether all bytes are 0x0 by iterating over chunks of the
buffer. The offset, or index of the chunk, was never changed, leading to
repeated comparison of only the first chunk. Use array notation and
access chunk via array index to compare all chunks of the buffer.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Pointer in phytec_imx8m_detect was accessed without checking it first.
Fix this by moving the pointer check in front of any accesses.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
phytec_imx8m_detect returns -1 on error, but the return type is u8
leading to 255 return values. Fix this by changing the return type to
int; there is no reason to keep it as u8 .
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the downstream kernel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the service manual.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
This adds support for the MT8365 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Migrate to the new environment format and drop most of the config.h.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
After talking with the author off-list I was reminded that this part of
the series was not supposed to be merged, only parts 1-3 upon further
review.
This reverts commit 58a277c207.
Signed-off-by: Tom Rini <trini@konsulko.com>
The base address of extended DDR does not change across the K3 family.
Setting this per SoC is not needed. Remove this definition to help
remove the last bits from K3 include/configs/*.h files.
Signed-off-by: Andrew Davis <afd@ti.com>
Updates as a result of TIFS core now reserving a virtual interrupt
for enabling interrupts between DM to TIFS core. Because of this
change other virtual interrupt counts decrease by one.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Share the MCU GPIO interrupts between A53 core and DM R5 core. Allocating
2 instances each to A53 and DM R5.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Update am62ax rm-cfg with allocation entries for C7x core. Following
updates are added for C7x:
- Share split BCDMA tx and rx channels between DM R5 and C7x
- Share rings for split BCDMA tx and rx channels between DM R5 and C7x
- Add Global events and Virtual interrupts for C7x
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
This file is common for all K3, move it out of board/ directory and
into mach-k3. As we need to change the path in k3-binman.dtsi let's
take this opportunity to switch to absolute paths which makes adding
non-TI boards (like Toradex Verdin) not need to override these paths.
Signed-off-by: Andrew Davis <afd@ti.com>
Simplify the way all MTD devices are parsed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since MTD devices are partioned, we got the following
error when command "dfu 0" is executed:
DFU alt info setting: done
ERROR: Too many arguments for nor0
ERROR: DFU entities configuration failed!
ERROR: (partition table does not match dfu_alt_info?)
Fixes: 31325e1b8b ("stm32mp1: dynamically build DFU_ALT_INFO")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DRAM configuration for the 1GB and 4GB imx8mp venice boards had a
bus mapping issue (channel A and B swapped) which creates an invalid
deskewing configuration during training causing the DRAM to not be able
to run at its full bus speed.
Update the various config structures to resolve this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Technexion PICO-IMX7 SoM is supporting USDHC3 (eMMC or micro SD on SoM)
and USDHC1 (SD on carrier board) to use on any carrier board like
PICO-NYMPH. Based on the U-Boot version from Technexion it adds
baseboard SD card boot detect to able to boot from selected USDHC1
or USDHC3 boot devices.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
Tested-by: Fabio Estevam <festevam@gmail.com>
