Add properties related to eMMC HS400 mode.
mmc-hs400-1_8v;
bus-width = <8>;
They had been already in kernel dts file since the first
lx2160ardb dts patch.
b068890 arm64: dts: add LX2160ARDB board support
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Move to use generic handoff dtsi (socfpga_arria10-handoff.dtsi) and include
the specify generated _handoff.h header file from qts-filter-a10.sh script.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a script to process HPS handoff data and generate a header
for inclusion in u-boot specific devicetree addons. The header
should be included in the top level of u-boot.dtsi.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Resend mailbox command for 3 times with 2ms interval in between if
it receives MBOX_RESP_TIMEOUT and MBOX_RESP_DEVICE_BUSY response code.
Add a wrapper function mbox_send_cmd_common_retry() for retry, change
all the callers to use this wrapper function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Sync latest mailbox response codes from SDM firmware.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Mailbox command which is too large to fit into the mailbox
FIFO command buffer can be sent to SDM in multiple parts.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mailbox driver should always check for the length of the response
and read the response data before returning the response status to
caller.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add miliseconds delay when waiting for mailbox event to happen
before timeout. This will ensure the timeout duration is predictive.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Document down the usage of boot_scratch_cold register to avoid
overlapping of usage in the code for S10 & Agilex.
The boot_scratch_cold register is generally used for passing
critical system info between SPL, U-Boot and Linux.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
All SoCFPGA platforms (except Cyclone V) are now switching
to CONFIG_WDT (driver model for watchdog timer drivers)
from CONFIG_HW_WATCHDOG.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Print reset state (warm/cold) together with the
source (watchdog/MPU) which has triggered the warm
reset on S10 & Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Include SDM triggered warm reset bit (BIT1) in Reset Manager's stat
register when checking for HPS warm reset status.
Refactor the warm reset mask macro for clarity purpose.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Timer only need to be initialized once in SPL.
This patch remove the redundancy of initializing the
timer again in U-Boot proper
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
'dwmac_socfpga' driver will setup the PHY interface during probe.
PHY interface setup in arch_misc_init() is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Now that PIE works when U-Boot is started from ROM, let's enable
CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via
ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the
configuration.
To get a writable initial stack, we need to keep the fixed initial
stack pointer, which points to DRAM in our case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
CONFIG_ARCH_SUPPORT_TFABOOT was used on the qemu-arm64 platform to
guard a tweak to the flash bank configuration. U-Boot now reads the
current flash setup from the devicetree, so there is no need for
this option anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently selecting CONFIG_POSITION_INDEPENDENT also forces us to use an
initial stack pointer relative to the beginning of the BSS section.
This makes some sense, because this should be writable memory anyway.
However the BSS section is not cleared or used until later in the
setup process (after relocation), so memory nearby might not be
available early enough to host the initial stack. This is an issue if
U-Boot is loaded from (Flash-)ROM, for instance.
Allow CONFIG_INIT_SP_RELATIVE to be turned off by a board's config, to
be able to select a fixed stack pointer, for instance in known good
DRAM.
This will help QEMU utilising PIE, when it's loaded to (Flash-)ROM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the actual offset between link and runtime address is zero, there
is no need for patching up U-Boot early when running with
CONFIG_POSITION_INDEPENDENT.
Skip the whole routine when the distance is 0.
This helps when U-Boot is loaded into ROM, or in otherwise sensitive
memory locations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When we build an arm64 target and enable POSITION_INDEPENDENT, we were
skipping our build-time dynamic relocation fixup routine (STATIC_RELA).
This was probably done because we didn't need it in this case, as the
PIE fixup routine in start.S would take care of that at runtime.
However when we now skip this routine (upon detecting that the fixup
offset is 0), this might lead to uninitialised pointers.
Remove the exception, so that we always do the build-time relocation.
NOTE: GNU binutils starting with v2.27.1 do this build-time relocation
automatically, to be in-line with other architecures. So on newer
toolchains our manual fixup is actually not needed. It doesn't hurt to
have it, though, so that we keep compatibility with the popular Linaro
toolchains, which lack this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The CONFIG_TFABOOT option is more about what U-Boot DOES NOT need to do
than to support some features.
Explain a bit more in the Kconfig help text to avoid misunderstandings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a device tree binding for the BOOT button on the Maix board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds the necessary device tree bindings.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Rick Chen <rick@andestech.com>
This modifies the existing led test to check for default led naming as
added in the previous patch.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----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=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
Octeon needs a platform specific cmd to boot the Linux kernel, as
specific parameters need to be passed and special handling for the
multiple cores (SMP) is needed.
Co-developed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
[use gd->ram_base instead of gd->bd->bi_memstart]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for Linux booting, as the memory infos need to be passed
in this bootmem format to the Linux kernel.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add header to handle bootinfo support, needed for Octeon Linux kernel
booting.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes the Octeon feature detection used in many Octeon
drivers.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes common register defines and accessor functions.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the necessary lowlevel init code, to enable SMP Linux
booting. This code will be used with the platform specific Octeon Linux
boot command "bootoctlinux", which starts a configurable number of cores
into Linux.
Additionally some erratas and lowlevel register initializations are
copied from the original Cavium / Marvell U-Boot source code, enabling
booting into the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
As noticed while working on the USB xHCI support, Octeon needs to flush
all pending writes so that the values are present in the memory. Add
this "syncw" instruction (twice) to flush_dcache_range().
Signed-off-by: Stefan Roese <sr@denx.de>
Import platform specific mangle-port.h header, allowing a area specific
swapping, which is needed on Octeon for USB & PCI areas.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_should_swizzle_table[] which is needed for the area
specific swapping. It will be used by the platform specific
mangle-port.h header.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the initialization call for the Octeon RAM driver to
the Octeon platforms code. So if enabled via Kconfig, the DDR driver
will be called and the RAM will be configured and used. If the RAM
driver is not enabled, the L2 cache is still used as RAM.
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header is used by the upcoming DDR driver and potentially by other
drivers ported from the 2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi
file. It also adds the L2C DT node, as this is referenced by the DDR
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
When using SDL for input the SDL key codes are first converted to Linux key
codes and then to matrix entries of the cross wired keyboard.
We must not map any key code to two different places on the keyboard. So
comment out one backslash position.
Update the rest of the file from Linux 5.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some blobs need a larger alignment than the default. For example, ACPI
tables often start at a 4KB boundary. Add support for this.
Update the size of the test blob to allow these larger records.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the correcly architectured USB Glue node for Meson AXG and the
S400 board in -u-boot.dtsi until support in upstream Linux then
backported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board_usb_init()/cleanup() for USB gadget for AXG based
on the code for the G12A architecture.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
DT alignment with Linux kernel v5.9-rc4 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The tests rely on a dummy driver to allocate and initialize the regmaps
and the regmap fields using the managed API. The first test checks if
the regmap config fields like width, reg_offset_shift, range specifiers,
etc work. The second test checks if regmap fields behave properly (mask
and shift are ok) by peeking into the regmap.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test to verify that GPIOs can be acquired/released using the managed
API. Also check that the GPIOs are released when the consumer device is
removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
This adds comments regarding the ordering and purpose of certain
instructions as I understand them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
This ensures constructs like `if (gd & gd->...) { ... }` work when
accessing the global data pointer. Without this change, it was possible for
a very early trap to cause _exit_trap to directly or indirectly (through
printf) to read arbitrary memory. This could cause a second trap,
preventing show_regs from being printed.
printf (and specifically puts) uses gd to determine what function to print
with. These functions in turn use gd to find the serial device, etc.
However, before accessing gd, puts first checks to see if it is non-NULL.
This indicates an existing (perhaps undocumented) assumption that either gd
is NULL or it is completely valid.
Before this patch, gd either points to unexpected data (because it retains
the value it did from the prior-stage) or points to uninitialized data
(because it has not yet been initialized by board_init_f_init_reserve)
until the hart has acquired available_harts_lock. This can cause two
problems, depending on the value of gd->flags. If GD_FLG_SERIAL_READY is
unset, then some garbage data will be printed to stdout, but there will not
be a second trap. However, if GD_FLG_SERIAL_READY is set, then puts will
try to print with serial_puts, which will likely cause a second trap.
After this patch, gd is zero up until either a hart has set it in
wait_for_gd_init, or until it is set by arch_init_gd. This prevents its
usage before its data is initialized because both handle_trap and puts
ensure that gd is nonzero before using it. After gd has been set, it is OK
to access it because its data has been cleared (and so flags is valid).
XIP cannot use locks because flash is not writable. This leaves it
vulnerable to the same class of bugs regarding already-pending IPIs as
before this series. Fixing that would require finding another method of
synchronization, which is outside the scope of this series.
Fixes: 7c6ca03eae ("riscv: additional crash information")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We can reduce the number of instructions needed to use available_harts_lock
by using the aq and rl suffixes for AMOs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Even though we no longer call smp_function if an IPI was not sent by
U-Boot, we still need to clear any IPIs which were pending from the
execution environment. Otherwise, secondary harts will busy-wait in
secondary_hart_loop, instead of relaxing.
Along with the previous commit ("riscv: Use a valid bit to ignore
already-pending IPIs"), this fixes SMP booting on the Kendryte K210.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Some IPIs may already be pending when U-Boot is started. This could be a
problem if a secondary hart tries to handle an IPI before the boot hart has
initialized the IPI device.
To be specific, the Kendryte K210 ROM-based bootloader does not clear IPIs
before passing control to U-Boot. Without this patch, the secondary hart
jumps to address 0x0 as soon as it enters secondary_hart_loop, and then
hangs in its trap handler.
This commit introduces a valid bit so secondary harts know when and IPI
originates from U-Boot, and it is safe to use the IPI API. The valid bit is
initialized to 0 by board_init_f_init_reserve. Before this, secondary harts
wait in wait_for_gd_init.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Without a matching barrier on the write side, the barrier in handle_ipi
does nothing. It was entirely possible for the boot hart to write to addr,
arg0, and arg1 *after* sending the IPI, because there was no barrier on the
sending side.
Fixes: 90ae281437 ("riscv: add option to wait for ack from secondary harts in smp functions")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Clearing MIP.MSIP is not guaranteed to do anything by the spec. In
addition, most existing RISC-V hardware does nothing when this bit is set.
The following commits "riscv: Use a valid bit to ignore already-pending
IPIs" and "riscv: Clear pending IPIs on initialization" should implement
the original intent of the reverted commit in a more robust manner.
This reverts commit 9472630337.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We currently do this in a u-boot specific dts, but hopefully we can get
these bindings added in Linux in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The interrupt controller property is removed from the clint binding because
the clint is not an interrupt-controller. That is, no other devices have an
interrupt which is controlled by the clint.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the clint driver from the riscv-specific interface to be a
DM-based UCLASS_TIMER driver. In addition, the SiFive DDR driver previously
implicitly depended on the CLINT to select REGMAP.
Unlike Andes's PLMT/PLIC (which AFAIK never have anything pass it a dtb),
the SiFive CLINT is part of the device tree passed in by qemu. This device
tree doesn't have a clocks or clock-frequency property on clint, so we need
to fall back on the timebase-frequency property. Perhaps in the future we
can get a clock-frequency property added to the qemu dtb.
Unlike with the Andes PLMT, the Sifive CLINT is also an IPI controller.
RISCV_SYSCON_CLINT is retained for this purpose.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
This merges the PLIC initialization code from two functions into one.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the PLMT driver from the riscv-specific timer interface to be
a DM-based UCLASS_TIMER driver.
The clock-frequency/clocks properties are preferred over timebase-frequency
for two reasons. First, properties which affect a device should be located
near its binding in the device tree. Using timebase-frequency only really
makes sense when the cpu itself is the timer device. This is the case when
we read the time from a CSR, but not when there is a separate device.
Second, it lets the device use the clock subsystem which adds flexibility.
If the device is configured for a different clock speed, the timer can
adjust itself.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured frequency. The timer drivers also do not have device structs,
and so have to rely on storing parameters in gd_t. Lastly, there is no
initialization call, so driver init is done in the same function which
reads the time. This can result in confusing error messages. To a user, it
looks like the driver failed when trying to read the time, whereas it may
have failed while initializing.
This patch removes the shim functionality from the riscv-timer driver, and
has it instead implement the former rdtime.c timer driver. This is because
existing u-boot users who pass in a device tree (e.g. qemu) do not create a
timer device for S-mode u-boot. The existing behavior of creating the
riscv-timer device in the riscv cpu driver must be kept. The actual reading
of the CSRs has been redone in the style of Linux's get_cycles64.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
-----BEGIN PGP SIGNATURE-----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=W9Wz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc6' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc6
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
The gp register is used to store U-Boot's global data pointer. We should
not assume that an UEFI application leaves the gp register unchanged as
the UEFI specifications does not define who is the owner of the gp and tp
registers.
So the following sequence should be followed in the trap handler:
* save the caller's gp register
* restore the global data pointer
* serve interrupts or print crash dump and reset
* restore the caller's gp register
Cc: Abner Chang <abner.chang@hpe.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Use "imply" instead of "select" for BOARD_EARLY_INIT_F config option,
and then disable it on boards which don't need it.
Updated grpeach_defconfig to disable CONFIG_BOARD_EARLY_INIT_F option for
RZA1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Mark the default s_init function as weak, so that SoC's can
override it if needed, and it will still be discarded if unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add support to identify R8A7796 r1.3 SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
It is useful to be able to flash Edison directly without relying on the
installed U-Boot being functional.
Add a binman image for this. It includes a 'OSIP' header (which happens to
look like an MBR / (Master-Boot Record), U-Boot binary and an environment.
I am not able to find a specification for OSIP.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We already use binman's 'multiple-images' feature with Chrome OS and we
want to use it for Edison. There is no real down-side.
Adjust x86 to always use multiple-images.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present the mtrr command only support 8 MTRRs. Some SoCs have more than
that. Update the implementation to support up to 10. Read the number of
MTRRs dynamically instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GUIDs are one of the seven evils of the computer world. They obfuscate the
meaning and require people to look up long hex strings to decode it.
Luckily only a miniscule fraction of the 10^38 possible GUIDs are in use.
Add a way to decode the GUIDs known to U-Boot. Add a few more to the list
for good measure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable new features and provide require device-tree config so that U-Boot
produces the correct ACPI tables on Coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards want to reserve extra regions of memory. Add a 'chosen'
property to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this function only supports FSP-M but it is also used to read
FSP-S, in which case FSP-M may be zero. Add support for showing whichever
address is present in the FSP binary.
Also change the debug() statements to log_debug() while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If locating the FSP header hangs for whatever reason it is useful to see
where it got stuck. Add a debug print. Also show the address of the FSP-S
entry point as a sanity check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file doesn't currently have a log category. Add one so that items
are logged correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides information about a v1 TPM in the system. Generate this
table if the TPM is present.
Add a required new bloblist type and correct the header order of one
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file cannot currently be included in ASL files. Add a header guard
to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is currently in the wrong place, so including the file in the device
tree fails. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Send this notification when U-Boot is about to boot into Linux, as
requested by the FSP.
Currently this causes a crash with the APL FSP, so leave it disabled for
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MTRR registers are programmed with the list the U-Boot
builds up in the same order. In some cases this list may be out of order.
It looks better in Linux to have the registers in order, so sort them,
Signed-off-by: Simon Glass <sjg@chromium.org>
This new method is intended to be called when UEFI shuts down the 'boot
services', i.e. any lingering code in the boot loader that might be used
by the OS.
Add a definition for this new method and update the comments a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't have CONFIG_PCI in TPL but it is present in SPL, etc. So this
code is not needed. Drop it, and fix a code-style nit just above.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support generating a DMAR table and add a few helper routines as well.
Also set up NHLT so that audio works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for generating various ACPI tables for Apollo Lake. Add a few
S3 definitions that are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Apollo Lake needs to generate a few more table types used on Intel SoCs.
Add support for these into the x86 ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are needed for the CPU tables. Add them into an x86-specific file
since we do not support them on sandbox, or include tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the DBG2 (Debug Port Table 2) ACPI table.
Adjust one of the header includes to be in the correct order, before
adding more.
Note that the DBG2 table is generic but the PCI UART is x86-specific at
present since it assumes an ns16550 UART. It can be generalised later
if necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the HPET (High Precision Event Timer) ACPI
table. Since this is x86-specific, put it in an x86-specific file
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some more definitions to the iomap. These will be used by
ACPI-generation code as well as the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SCI and power-state definitions required by ACPI tables. Fix the
license to match the original source file.
Als update the guard on acpi_pmc.h to avoid an error when buiding ASL.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot does not support SMM (System Management Mode) at present, but needs
a few definitions to correctly set up the ACPI table. Add these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Intel WiFi chips can use a common routine to write the information needed
by linux. Add an implementation of this.
Enable it for coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices can wake the system from sleep, e.g opening the lid on a
clamshell or moving a USB mouse.
Add a wake to specify this for USB devices and add the settings for Apollo
Lake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand this to 4KB so that it is possible to add custom information to it.
On Chromebooks this is used to pass verified-boot information.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot puts a magic number in the ASL for the GNVS table and
searches for it later.
Add a Kconfig option to use a different approach, where the ASL files
declare the table as an external symbol. U-Boot can then put it wherever
it likes, without any magic numbers or searching.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the definition of this structure common to Intel devices. It includes
some optional Chrome OS pieces which are used when vboot is integrated.
Drop the APL version as it is basically the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add common x86 ASL files, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
When booting Chrome OS images the command line is stored separately
from the kernel. Add a way to specify this address so that images boot
correctly.
Also add comments to the zimage.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: adjust maxargs to 8 for 'zboot start']
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There is a lot of information in the setup block and it is quite hard to
decode manually. Add a 'zboot dump' command to decode it into a
human-readable format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the setup block is always obtained from the image
automatically. In some cases it can be useful to use a setup block
obtained elsewhere, e.g. if the image has already been unpacked. Add an
argument to support this and update the logic to use it if provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: adjust maxargs to 7 for 'zboot start']
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present it is not possible to tell from a script where the setup block
is, or where the image was loaded to. Add environment variables for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subcommand that sets up the kernel ready for execution.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
