Commit graph

1013 commits

Author SHA1 Message Date
Tom Rini
44faff24f5 Merge git://git.denx.de/u-boot-fsl-qoriq 2016-06-28 15:59:05 -04:00
Peng Fan
1483151e84 mmc: fsl: introduce wp_enable
Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.

Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.

If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Ye Li
84ecdf6da9 fsl_esdhc: Update clock enable bits for USDHC
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
   implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
   external card and reinitialize it.

So in this patch, we change to use the vendorspec registers for these bits
operation.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Peng Fan
f53225cce4 mmc: fsl: reset to normal boot mode when eMMC fast boot
When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.

This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.

Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Jaehoon Chung
ca2ec9adc9 mmc: dw_mmc: fix the wrong AND operation
These condition checking are wrong.
Original Author's intention might be "&" instead of "&&".
It can know whether receive or transmit data request with
BIT[4]/BIT[5] of RINTSTS register.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-06-27 09:43:26 +09:00
Stefan Wahren
1a3619cf82 mmc: add MMC_VERSION_5_1
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
2016-06-20 05:14:46 -04:00
Stephen Warren
135aa95002 clk: convert API to match reset/mailbox style
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
  provider now implements a single set of clocks. This provides a simpler
  conceptual interface to clients, and better aligns with device tree
  clock bindings.
* Clocks are now identified with a single "struct clk", rather than
  requiring clients to store the clock provider device and clock identity
  values separately. For simple clock consumers, this isolates clients
  from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
  clk-uclass.h contains the provider API. This aligns with the recently
  added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
  can customize these operations if needed. This also aligns with the
  recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
  clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.

Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.

test/py passes for sandbox (which invokes the dm clk test amongst
others).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-19 17:05:55 -06:00
Eddy Petrișor
9702ec00e9 armv8: s32v234: Introduce basic support for s32v234evb
Add initial support for NXP's S32V234 SoC and S32V234EVB board.

The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.

Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>

Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
2016-06-13 08:56:35 -04:00
Heiko Schocher
3d4f628d2f mmc: omap_hsmmc: enable 8bit interface for eMMC for AM33xx
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:09 -04:00
Heiko Schocher
a5e27b416f mmc: revert mmc: Handle switch error status bit in MMC card status
revert patch:
commit: 6b2221b008: mmc: Handle switch error status bit in MMC card status

to get eMMC working on shc board

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:08 -04:00
Tom Rini
c41c649c2f Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-06-04 08:49:08 -04:00
Yangbo Lu
cc634e2836 mmc: fsl_esdhc: fix check_and_invalidate_dcache_range function
In function check_and_invalidate_dcache_range(), there are incorrect
start address and end address of the dcache range calculated for
Layerscape platforms. This patch is to fix this issue.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:05 -07:00
Stephen Warren
39f633320c mmc: tegra: add basic Tegra186 support
Tegra186's MMC controller needs to be explicitly identified. Add another
compatible value for it.

Tegra186 will use an entirely different clock/reset control mechanism to
existing chips, and will use standard clock/reset APIs rather than the
existing Tegra-specific custom APIs. The driver support for that isn't
ready yet, so simply disable all clock/reset usage if compiling for
Tegra186. This must happen at compile time rather than run-time since the
custom APIs won't even be compiled in on Tegra186. In the long term, the
plan would be to convert the existing custom APIs to standard APIs and get
rid of the ifdefs completely.

The system's main eMMC will work without any clock/reset support, since
the firmware will have already initialized the controller in order to
load U-Boot. Hence the driver is useful even in this apparently crippled
state.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 11:22:59 -07:00
Simon Glass
e6c28073f9 dm: mmc: Use cfg directly in mmc_bind()
This small change tidies up the code slightly.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:10 -06:00
Simon Glass
e419a3ec1a dm: mmc: Fix up mmc_bread/bwrite() prototypes for SPL
When these functions are not compiled in, we still need to declare the
correct function signature to avoid a build warnings in SPL. Fix this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:10 -06:00
Simon Glass
f6e41d17ab dm: rockchip: mmc: Allow use of CONFIG_BLK
Allow driver model to be used for block devices in the rockchip mmc driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:09 -06:00
Simon Glass
5e6ff810c3 dm: mmc: dwmmc: Support CONFIG_BLK
Add support for using driver model for block devices in this driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:09 -06:00
Simon Glass
19d2e34237 dm: mmc: Convert sdhci to support CONFIG_BLK
Update sdhci.c so that it works with driver model enabled for block devices.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:08 -06:00
Simon Glass
61fe076f0f mmc: Use byte array for multipliers
We don't need an int since no value is over 80. This saves a small amount of
SPL space (about 44 bytes).

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-26 20:50:29 -06:00
Simon Glass
e98dd20cce mmc: Drop mmc_register()
This function is no longer used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-26 20:50:29 -06:00
Simon Glass
f376a3cbbf dm: mmc: sandbox: Add an SD-card emulation
Add an emulation of an SD card to sandbox, allowing MMC to be used in tests.
The emulation is very simple, supporting only card detection and reading
test data.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
33fb211dd2 dm: mmc: Add support for driver-model block devices
Add support for enabling CONFIG_BLK with MMC. This involves changing a
few functions to use struct udevice and adding a MMC block device driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
ad27dd5e13 dm: mmc: Add a way to bind MMC devices with driver model
Binding an MMC device when CONFIG_BLK is enabled requires that a block
device be bound as a child of the MMC device. Add a function to do this.
The mmc_create() method will be used only when DM_BLK is disabled.

Add an unbind method also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
8ef761ed4c dm: mmc: Implement the MMC functions for block devices
Implement the functions in mmc_legacy.c for driver-model block devices, so
that MMC can use driver model for these. This allows CONFIG_BLK to be enabled
with DM_MMC.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
f8b7752e8f dm: sandbox: Only enable the sandbox MMC driver when valid
This driver will require generic MMC and block-device support in a future
commit. To avoid test errors, make this change now.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
fdbb139f0c dm: mmc: Adjust mmc_switch_part() to use a struct mmc
Instead of looking up the MMC device by number, just pass it in. This makes
it possible to use this function with driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
c40fdca6b7 dm: mmc: Move the device list into a separate file
At present the MMC subsystem maintains its own list of MMC devices. This
cannot work with driver model, which needs to maintain this itself. Move the
list code into a separate 'legacy' file. The core MMC code remains, and will
be shared with the driver-model implementation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
cffe5d86cf dm: mmc: Set up the device pointer when using the MMC uclass
Update the existing drivers to set up this new pointer. This will be required
by the MMC uclass.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
69f45cd53b dm: mmc: Use the new select_hwpart() API
Avoid calling directly into the MMC code - use the new API call instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
cb5ec33d90 dm: mmc: Add a function to obtain the block device
The MMC block device is contained within struct mmc. But with driver model
this will not be the case. Add a function to obtain the block device. We
can later implement this for CONFIG_BLK.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
e17d1143c1 dm: mmc: Implement the select_hwpart() method
Implement this method so that hardware partitions will work correctly with
MMC.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
ff3882ac23 dm: mmc: Move mmc_switch_part() above its callers
This function is defined after it is used. In preparation for making it
static, move it up a little. Also drop the printf() which should not appear
in a driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
3c457f4d2e dm: mmc: Drop the get_dev() function
This function is implemented by the legacy block functions now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
663acabdc5 dm: mmc: Add a legacy block interface for MMC
Add a legacy block interface for MMC.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Masahiro Yamada
cacd1d2f33 mmc: sdhci: add const qualifier to the name of struct sdhci_host
This allows to drop annoying (char *) casts when setting the host
name of struct sdhci_host.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-25 15:10:42 -04:00
Mugunthan V N
5cc6a2458e drivers: mmc: omap_hsmmc: request cd and wp gpios when DM_MMC is defined
Add request gpio for CD and WP gpios, so that the gpio can be
used for the respective purposes.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 12:29:16 -04:00
Mugunthan V N
4bc5e19e12 drivers: mmc: omap_hsmmc: Fix conversion of address to a pointer
omap_hsmmc driver directly typecasts fdt_addr_t to a pointer.
This is not strictly correct, as it gives a build warning when
fdt_addr_t is u64. So, use map_physmem for a proper typecasts.

This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")

drivers/mmc/omap_hsmmc.c: In function ‘omap_hsmmc_ofdata_to_platdata’:
drivers/mmc/omap_hsmmc.c:776:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  priv->base_addr = (struct hsmmc *)dev_get_addr(dev);
                      ^

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 12:29:15 -04:00
Marek Vasut
dafd5792a8 arm: socfpga: Nuke useless include
The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-10 17:19:49 +02:00
Peng Fan
96f0407b00 fsl: esdhc: support driver model
Support Driver Model for fsl esdhc driver.

1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
   - Introduce fsl_esdhc_init to be common usage for DM and non-DM
   - Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
   - The original API for board code is still there, but we use
     'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
   fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
   the clk and fill 'priv->sdhc_clk'.

Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
 simple_bus  [ + ]    |   `-- aips-bus@02100000
  mmc        [ + ]    |       |-- usdhc@02190000
  mmc        [ + ]    |       |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Hector Palacios <hector.palacios@digi.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-By: Eric Nelson <eric@nelint.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:33:37 -07:00
Mateusz Kulikowski
9d11d12a16 mmc: Add support for Qualcomm SDHCI controller
Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:08 -04:00
Tom Rini
40345e9ea7 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-04-01 08:17:55 -04:00
Siarhei Siamashka
d96ebc468d sunxi: Add support for Allwinner A64 SoCs
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.

Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Alexander Graf
0ea5a04fbc sunxi: Explicitly cast u32 pointer conversions
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Masahiro Yamada
4f80501b91 mmc: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:19 +09:00
Bin Meng
7863ce5891 mmc: Print send_cmd response only when return value is zero
send_cmd response is valid only when no error happened. If an error
occured, let mmc_send_cmd() print the return value to aid debugging.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:24 -04:00
Bin Meng
53e8e40b47 mmc: Fix switch..case indention
Correct the indention level of switch..case statements.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:24 -04:00
Stephen Warren
a481a15600 mmc: bcm2835: fix 64-bit build warning
Fixes:
drivers/mmc/bcm2835_sdhci.c: In function ‘bcm2835_sdhci_init’:
drivers/mmc/bcm2835_sdhci.c:181:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2016-03-27 09:12:21 -04:00
Alexander Graf
9b5b8b6ee1 dwmmc: Increase retry timeout
When enable dcache on HiKey, we're running into MMC command timeouts
because our retry loop is now faster than the eMMC (or an external SD
card) can answer.

Increase the retry count to the same as the timeout value for status
reports.

The real fix is obviously to not base this whole thing on a cycle counter
but on real wall time, but that would be slightly more intrusive.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-15 15:13:05 -04:00
Paul Kocialkowski
fbf1b08a93 omap_hsmmc: Board-specific TWL6030 MMC power initialization
Boards using the TWL6030 regulator may not all use the LDOs the same way.
Some might also not use MMC1 at all, so VMMC would't have to be enabled.

This delegates TWL6030 MMC power initializations to board-specific functions,
that may still call twl6030_power_mmc_init for the default behavior.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:11:29 -04:00
Paul Kocialkowski
a85362fb3e power: twl6030: Device-index-specific MMC power initialization
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC and VAUX1, in doubt.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:10:51 -04:00
Tom Rini
88033d737d Merge git://git.denx.de/u-boot-dm 2016-03-14 19:21:44 -04:00
Stefan Roese
ecb57f69b2 lib/crc16.c: Rename cyg_crc16() to crc16_ccitt() and add crc start value
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.

To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:42 -04:00
Simon Glass
bcce53d048 dm: block: Rename device number member dev to devnum
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
3e8bd46950 dm: part: Rename some partition functions
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
4101f68792 dm: Drop the block_dev_desc_t typedef
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Masahiro Yamada
a111bfbfad mmc: uniphier: add driver for UniPhier SD/MMC host controller
Add a driver for the on-chip SD/eMMC host controller used by
UniPhier SoC family.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:15 +09:00
Michal Simek
ce0335f2b4 mmc: Kconfig: Add Arasan SDHCI entry
Add Arasan SDHCI entry to Kconfig and fix all references.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22 16:21:02 +01:00
Simon Glass
e05ab0dae8 tegra: mmc: Fix comments in the MMC driver init
Fix the SoC names in two comments.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:50 -07:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Tom Rini
161b1fe745 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-02-02 07:24:52 -05:00
Andrei Pistirica
102142c9e0 drivers: mmc: add driver for Microchip PIC32 SDHCI controller.
This driver implements platform specific glue and fixups for
PIC32 internal SDHCI controller.

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01 22:14:01 +01:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Yangbo Lu
25503443ee mmc: fsl_esdhc: set Abort command type for CMD12
According to SD spec, CMD12, CMD52 for writing I/O abort in CCCR need
to be set an Abort command type when they are sent. So, we remove all
chip-specific #ifdefs and make it available for all platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:13 -08:00
Yangbo Lu
e978a31b63 mmc: fsl_esdhc: increase data transaction timeout to 500ms
The MMC spec says "It is strongly recommended for hosts to implement
more than 500ms timeout value even if the card indicates the 250ms
maximum busy length."  Even the previous value of 300ms is known to
be insufficient for some cards. So, increase the timeout to 500ms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Siva Durga Prasad Paladugu
b215614638 mmc: zynq_sdhci: Added qurik to disable high speed
Add quirk to disable high speed incase the high
speed was broken.This solves the issue where the
the controller is used in High Speed Mode and the
the hold time requirement for the JEDEC/MMC 4.41
specification is NOT met.
This timing issue is not on all boards and hence
provided config option to enable it when required.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:54 +01:00
Siva Durga Prasad Paladugu
4297900260 mmc: sdhci: Clear high speed if not supported
Clear high speed bit if it was not supported by
the driver.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:54 +01:00
Siva Durga Prasad Paladugu
a57a4a5d83 sdhci: zynq: Remove hardcoded value zero as min frequency
Remove hardcoded value zero as min frequency and
use config option CONFIG_ZYNQ_SDHCI_MIN_FREQ
defined in board config

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:54 +01:00
Gregory CLEMENT
b4670a0c2b mmc: atmel: Properly fix clock configuration
Timing issue occurs on eMMC not only when modifying the frequency but
also for all the switch command(CMD6). According to the MMC spec waiting
8 clocks after a switch command would be the thing to do.

This patch allows fixing CPU hang observed when trying to changing the
bus width on a eMMC on SAMA5D4.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marek Vasut <marex@denx.de> # on DENX MA5D4EV
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com> # on atngw100
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixed minor checkpatch warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-27 13:58:58 +01:00
Simon Glass
898d64395c rockchip: Use a separate clock ID for clocks
At present we use the same peripheral ID for clocks and pinctrl. While this
works it is probably better to use the device tree clock binding ID for
clocks. We can use the clk_get_by_index() function to find this.

Update the clock drivers and the code that uses them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Simon Glass
e1efec4e0a rockchip: mmc: Use a pwrseq device if available
Use the pwrseq uclass to find a suitable power sequence for the MMC device.
If this is enabled in the device tree, we will pick it up automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Simon Glass
4a1db6d8ab dm: mmc: Try to honour the sequence order
At present we add driver-model MMC devices in the order we find them. The
'alias' order is not honoured.

It is difficult to fix this for the case where we have holes in the
sequence. But for the common case where the devices are numbered from 0
without any gaps, we can add the devices to the internal data structures
in this order.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-20 19:06:22 -07:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
huang lin
6579385b46 mmc: rockchip: the non-removable property must point to emmc
the non-removable property point to sdcard before, it is wrong,
it must point to emmc, correct it.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-01-15 05:39:27 -07:00
Stephen Warren
873cc1d777 mmc: store hwpart in the block device
This will allow us to have multiple block device structs each referring
to the same eMMC device, yet different HW partitions.

For now, there is still a single block device per eMMC device. As before,
this block device always accesses whichever HW partition was most recently
selected. Clients wishing to make use of multiple block devices referring
to different HW partitions can simply take a copy of this block device
once it points at the correct HW partition, and use each one as they wish.
This feature will be used by the next patch.

In the future, perhaps get_device() could be enhanced to return a
dynamically allocated block device struct, to avoid the client needing to
copy it in order to maintain multiple block devices. However, this would
require all users to be updated to free those block device structs at some
point, which is rather a large change.

Most callers of mmc_switch_part() wish to permanently switch the default
MMC block device's HW partition. Enhance mmc_switch_part() so that it does
this. This removes the need for callers to do this. However,
common/env_mmc.c needs to save and restore the current HW partition. Make
it do this more explicitly.

Replace use of mmc_switch_part() with mmc_select_hwpart() in order to
remove duplicate code that skips the call if that HW partition is already
selected.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:19 -05:00
Stephen Warren
7c4213f6a5 block: pass block dev not num to read/write/erase()
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:18 -05:00
Simon Glass
4abe8e40a7 dm: Convert PCI MMC over to use DM PCI API
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.

Adjust this code to use the new driver model PCI API.

This should move over to the new MMC uclass at some point.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12 10:19:09 -07:00
Eric Nelson
1aa2d074a7 mmc: update MMC_ERASE argument to match Linux kernel.
Table 41 of the JEDEC standard for eMMC says that bit 31 of
the command argument is obsolete when issuing the ERASE
command (CMD38) on page 115 of this document:
	http://www.jedec.org/sites/default/files/docs/jesd84-B45.pdf

The SD Card Association Physical Layer Simplified Specification also
makes no mention of the use of bit 31.
	https://www.sdcard.org/downloads/pls/part1_410.pdf

The Linux kernel distinguishes between secure (bit 31 set) and
non-secure erase, and this patch copies the macro names from
include/linux/mmc/core.h.

Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
Tested-by: Hector Palacios <hector.palacios@digi.com>
2016-01-04 11:17:43 -05:00
Tom Rini
f1993ca066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03 10:32:24 -05:00
Eric Nelson
f0b5f23f32 ARM: imx: fsl_esdhc: fix usage of low 4 bits of sysctl register
The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.

Guard against their usage by hiding the bit mask macros on those
processors.

These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.

>From the i.MX6DQ RM:
	To prevent possible glitch on the card clock, clear the
	FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
	or DVS in System Control Register) or setting RSTA bit.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
2016-01-03 15:21:21 +01:00
Dinh Nguyen
a1684b6105 arm: socfpga: fix up a questionable macro for SDMMC
Move the macro into the socfpga_dwmci_clksel().

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
[fix parenthesis in the sdmmc_mask]
2015-12-20 03:44:56 +01:00
Sjoerd Simons
fc011f6402 mmc: mmc: Don't use sprintf when using tiny-printf
There is no sprintf implementation in tiny-printf, so don't try to use
it when tiny-printf if used.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2015-12-13 17:07:31 -07:00
Tom Rini
dcf4cb068e Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze 2015-12-07 08:13:02 -05:00
Michal Simek
d9ae52c8f0 zynq: sdhci: Move driver to DM
Move driver to DM

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-07 10:14:29 +01:00
Michal Simek
400434537b zynq: sdhci: Remove zynq_sdhci_of_init()
Prepare for using DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 10:14:29 +01:00
Siva Durga Prasad Paladugu
b8a9bebeec zynq: sdhci: Calculate minimum frequency based on max frequency
Calculate the minimum sd clock based on max clock. This will
be done by add_sdhci() if we pass minimum clock as zero.
It also does based on SD host contoller version.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 10:14:29 +01:00
Marek Vasut
c35ed77a78 mmc: dwmmc: socfpga: Convert to DM
Convert the SoCFPGA shim for registering the DWMMC driver to DM.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2015-12-07 00:15:59 +01:00
huang lin
2863724831 rockchip: mmc: get the fifo mode and fifo depth property from dts
rk3036 mmc do not have internal dma, so we use fifo mode when read
and write data, we get the fifo mode and fifo depth property from
dts, pass to dw_mmc driver.

Signed-off-by: Lin Huang <hl@rock-chips.com>
2015-12-01 08:07:22 -07:00
huang lin
ace2198b7c rockchip: mmc: use non-removable property to distinguish emmc and sdcard register
emmc and sdcard have different register address, use non-removeable property
to distinguish them.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-12-01 08:07:22 -07:00
huang lin
a65f51b978 mmc: dw_mmc: support fifo mode in dwc mmc driver
some soc(rk3036 etc) use dw_mmc but do not have internal dma,
so we implement fifo mode to read and write data.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-12-01 08:07:22 -07:00
huang lin
f382eb833a mmc: dw_mmc: move data transfer as a separate function
the data transfer seem to long in the dwmci_send_cmd function,
so move this block as a separate funciton.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-12-01 08:07:22 -07:00
Chin Liang See
9a41404dc6 mmc: socfpga_dw_mmc: Move drvsel and smplsel to dts
socfpga_dw_mmc driver will obtain the drvsel and
smplsel value from device tree instead of definition
in config header file.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-11-30 13:30:19 +01:00
Michal Simek
f3bd72801a zynq: sdhci: Define max clock by macro
zc1571 with silicon can operate on 200MHz maximum frequency. Setup this
frequency by default and fix setting for ep108.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-11-19 14:03:05 +01:00
Prabhakar Kushwaha
41f7be3c78 driver: dwmmc: Fix pointer conversion warnings for hikey
Fix below compilation warings happening for hikey_defconfig

drivers/mmc/dw_mmc.c: In function ‘dwmci_set_idma_desc’:
drivers/mmc/dw_mmc.c:43:20: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
  desc->next_addr = (unsigned int)desc + sizeof(struct dwmci_idmac);
                    ^
drivers/mmc/dw_mmc.c: In function ‘dwmci_prepare_data’:
drivers/mmc/dw_mmc.c:61:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
  dwmci_writel(host, DWMCI_DBADDR, (unsigned int)cur_idmac);
                                   ^
drivers/mmc/dw_mmc.c:73:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
         (u32)bounce_buffer + (i * PAGE_SIZE));
         ^
  CC      drivers/mmc/hi6220_dw_mmc.o
drivers/mmc/hi6220_dw_mmc.c: In function ‘hi6220_dwmci_add_port’:
drivers/mmc/hi6220_dw_mmc.c:51:17: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
  host->ioaddr = (void *)regbase;

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2015-11-12 15:59:00 -05:00
Tom Rini
60b25259a5 Merge git://git.denx.de/u-boot-samsung 2015-11-05 07:46:45 -05:00
Wenyou Yang
a3b59b1523 mmc: atmel: Add atmel sdhci support
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-03 14:21:31 +01:00
Wenyou Yang
79667b7b76 mmc: sdhci: Fix the SD clock stop sequence
According to the SDHC specification, stopping the SD Clock is by setting
the SD Clock Enable bit in the Clock Control register at 0, instead of
setting all bits at 0.

Before stopping the SD clock, we need to make sure all SD transactions
to complete, so add checking the CMD and DAT bits in the Presen State
register, before stopping the SD clock.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2015-11-03 14:21:30 +01:00
Yangbo Lu
bf50be835e mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:50:29 -08:00
Yangbo Lu
cdc69550d2 mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5 Adapter Card
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:51 -08:00
Shaohui Xie
512bdbd46a Powerpc: eSDHC: expand a fix to T4160
commit b8e5b07225 "Powerpc: eSDHC: Fix mmc read write err in uboot of
T4240QDS board", T4160 also needs this fix.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:32 -08:00
Przemyslaw Marczak
96094d4c46 s5p sdhci: call pinmux for card's gpio pins before use them
The SD card detection depends on checking one pin state.
But the pin was configured after card was detected, which is wrong.

This commit fixes this, by moving call to pinmux before use the pin.

Tested-on: Odroid U3 and Odroid X2.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:14 +09:00
Marek Vasut
877807e193 mmc: atmel: Zap global 'initialized' variable
Global variables are bad. Get rid of this particular one, so we can
correctly instantiate multiple atmel mci interfaces, without having
them interfere with one another.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-01 22:02:15 +01:00
Marek Vasut
6b75d35949 mmc: atmel: Implement proper private data
Instead of passing just the register area as a private data, introduce
a proper struct atmel_mci_priv structure instead. This will become useful
in the subsequent patch, where we eliminate the global variable from this
driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix free()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-01 22:02:15 +01:00
Marek Vasut
ecfb0ff812 mmc: atmel: Fix clock configuration
After silencing the prints which were generated when reconfiguring the
clock of the SD/MMC bus, surprisingly, the driver stopped working such
that every attempt to use the SD/MMC bus caused the CPU to get totally
stuck hard. It turns out that the prints generated a short delay, which
was necessary for the CPU to reconfigure the clock without getting stuck.
Thus, this patch adds a short delay after the clock configuration instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-01 22:02:15 +01:00
Marek Vasut
b84c9c9a98 mmc: atmel: Silence debug output
This driver generates clearly debugging prints when changing clock
speed, so silence those. Furthermore, the driver generates further
prints in case a command fails to complete. The later case woud be
useful, but for eMMC, command 8 can fail and it's not an error but
a part of the specification. Thus, make this debug() as well.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-01 22:02:14 +01:00
Yangbo Lu
8ef0d5c438 armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardb
This patch adds esdhc support for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Mugunthan V N
a9d6a7e23a drivers: mmc: omap_hsmmc: convert driver to adopt device driver model
adopt omap_hsmmc driver to device driver model

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:43:57 -04:00
Roger Quadros
3b68939fa0 ARM: k2g: add SD card and eMMC support
Add MMC support for k2g

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:22:25 -04:00
Tom Rini
e8d124fae0 Merge git://git.denx.de/u-boot-marvell 2015-10-20 21:59:40 -04:00
Stefan Roese
5b37212a3d mmc: mv_sdhci: Configure the SDHCI MBUS bridge windows
This driver did not yet configure the SDHCI MBUS bridge registers.
Without this and with CONFIG_MMC_SDMA enabled, mmc hangs at random
times. As DMA cannot complete correctly.

Tested on db-88f6820-gp eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dirk Eibach <eibach@gdsys.cc>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
2015-10-21 02:25:02 +02:00
Maxime Ripard
44c798799f sunxi: Use Kconfig CONFIG_MMC
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20 22:48:28 +02:00
Maxime Ripard
7a777f6d6f mmc: Add generic Kconfig option
Add a generic Kconfig option for the CONFIG_MMC option that was used before
in the configuration headers.

Since all the architectures need to be converted to that first, depend on
an non-existent config option that will be extended with architectures that
use that option.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20 22:48:28 +02:00
Tobias Jakobi
2308ea7c6f exynos: more debug and cleanup in do_sdhci_init()
Add more debug printfs in do_sdhci_init() for calls
that can potentially fail.

Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-13 20:22:28 +09:00
Tobias Jakobi
995a54cc12 exynos: be more verbose in process_nodes()
In case sdhci_get_config() or do_sdhci_init() fail, show
the error code that was returned.

Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-13 20:22:28 +09:00
Tobias Jakobi
6a9fbb6e20 exynos: Fix passing of errors in exynos_mmc_init()
exynos_mmc_init() always returns zero, so for the caller
it looks like it never fails.

Correct this by returning the error code of process_nodes().
For process_nodes() do something similar and return early
when do_sdhci_init() fails.

v2: Only fail in process_nodes() if we fail on all
    available nodes.

Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-13 20:22:28 +09:00
Tobias Jakobi
1a9d1731f9 exynos: Properly zero initialize host in s5p_sdhci_init()
This makes sure that setting the host_caps in s5p_sdhci_core_init()
doesn't operate on potentially uninitialized memory.

Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-13 20:22:28 +09:00
Hans de Goede
be90974c43 sunxi: mmc: Fix clk-delay settings
In recent allwinner kernel sources the mmc/sdio clk-delay settings have
been slightly tweaked, and for sun9i they are completely different then
what we are using.

This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).

For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (first introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (first introduced in A23 sdk)
-Above 50 MHz change the out delay from 2 to 1 (first introduced in A20 sdk)

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-29 11:50:07 +02:00
Łukasz Majewski
4d58e10e3e mmc: dw_mmc: Increase timeout to 4 minutes (as in Linux kernel)
The commit: d9dbb97be0
"mmc: dw_mmc: Zap endless timeout" removed endless loop waiting for end
of dw mmc transfer.

For some workloads - dfu test @ Odroid XU3 (sending 8MiB file) -
and SD cards (e.g. MicroSD Kingston 4GiB, Adata 4GiB)
the default timeout is to short.

The new value - 4 minutes (240 seconds) - is the same as the one used in
Linux kernel driver. Such fix should be good enough until we come up
with better fix for this issue.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
2015-09-28 11:03:56 -04:00
Simon Glass
cf92e05c01 Move ALLOC_CACHE_ALIGN_BUFFER() to the new memalign.h header
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 17:15:20 -04:00
Marek Vasut
129adf5bf4 mmc: dw_mmc: Probe the MMC from OF
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.

This patch now also removes previous temporary workaround.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
2015-09-04 11:54:20 +02:00
Sjoerd Simons
8e3332e223 mmc: Probe DM based mmc devices in u-boot
During mmc initialize probe all devices with the MMC Uclass if build
with CONFIG_DM_MMC

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-02 21:28:24 -06:00
Simon Glass
a8cb4fb56a rockchip: Add an MMC driver
Add an MMC driver which supports RK3288, but may also support other SoCs.
It uses the Designware MMC device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-02 21:28:24 -06:00
Simon Glass
e3563f2ec7 mmc: Support bypass mode with the get_mmc_clk() method
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-09-02 21:28:23 -06:00
Yousong Zhou
28f69b9a22 sunxi: mmc: set transfer timeout according to byte_cnt.
Originally a timeout value of 2 seconds was used regardless of the size
of data to be transfered.  This prevented slow devices from working
correctly while there was no much gain for faster devices, e.g. it takes
3708ms for a transfer of uImage of size 1899008 bytes.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Marcel Ziswiler
54a5cf81c4 arm: pxa: mmc: clean-up include file order
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2015-08-24 20:30:37 +02:00
Masahiro Yamada
0f9258228e of: clean up OF_CONTROL ifdef conditionals
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-18 13:46:05 -04:00
Tom Rini
0741701acf Merge branch 'master' of git://git.denx.de/u-boot-mmc 2015-08-13 07:20:44 -04:00
Yoshinori Sato
6f67b69b15 mmc_spi: Big-endian support
Currently implement always swap for big-endian value.
So doesn't work big-endian environment.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
2015-08-13 11:24:26 +03:00
Simon Glass
760177dff4 dw_mmc: Calculate dwmmc FIFO threshold size if not provided
We can calculate this. Add code to do this if it is not provided.

panto: prefix changed to dw_mmc to make things easier to grep

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-08-13 11:24:26 +03:00
Nikita Kiryanov
9fbdca6056 mmc: omap_hsmmc: enable 8bit interface for eMMC for AM43xx
Enable 8bit interface on HSMMC2 for am43xx to support 8bit eMMC chips.

Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-08-12 20:48:04 -04:00
Nikita Kiryanov
dce55b934d mmc: omap_hsmmc: enable proper CMD(DAT) lines reset procedure for am43xx
The CMD(DAT) lines reset procedure described in the OMAP4(AM335x,
OMAP5, DRA7xx) TRMs is also necessary for AM43XX. Enable it in the
driver.

Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-08-12 20:48:04 -04:00
Peter Griffin
447da58b57 mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-12 20:48:01 -04:00
Simon Glass
1c87ffe8d1 mmc: dw_mmc: Avoid using printf() for errors
The dw_mmc driver uses printf() in various places.

These bloat the code and cause problems for SPL. Use debug() where possible
and try to return a useful error code instead.

panto: Small rework to make it apply against top of tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-08-11 21:52:43 +03:00
Marek Vasut
9042d974d2 mmc: dw_mmc: Improve handling of data transfer failure
In case the data transfer failure happens, instead of returning
immediatelly, make sure the DMA is disabled, status register is
cleared and the bounce buffer is stopped.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
2015-08-11 20:44:30 +03:00
Marek Vasut
d9dbb97be0 mmc: dw_mmc: Zap endless timeout
Endless timeouts are bad, since if we get stuck in one, we have no
way out. Zap this one by implementing proper timeout.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
2015-08-11 20:44:21 +03:00
Marek Vasut
603b2f3a74 mmc: dw_mmc: Stop bounce buffer even in case of failure
The driver didn't stop the bounce buffer in case a data transfer
failed. This would lead to memory leakage if the communication
between the CPU and the card is unreliable. Add the missing call
to stop the bounce buffer.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
2015-08-11 20:43:34 +03:00
Simon Glass
c95ed7d9e7 exynos: Correct return value in exynos_mmc_init()
This function should return 0 on success, not 1. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:14 -06:00
Tom Rini
e3d50d4292 fsl_esdhc.c: Always make check_and_invalidate_dcache_range available
This function is called from esdhc_send_cmd so we need it available to
everyone.

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-02 10:27:52 -04:00
Tom Rini
7a1af7a79b Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-08-02 07:40:37 -04:00
Tom Warren
7aaa5a60ce ARM: Tegra210: Add support to common Tegra source/config files
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2015-07-28 10:30:20 -07:00
Thierry Reding
c39e2a75fd mmc: tegra: Build warning fixes for 64-bit
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-07-27 15:54:02 -07:00
Peng Fan
4683b22065 mmc:fsl_esdhc invalidate dcache before read
DCIMVAC is upgraded to DCCIMVAC for the individual processor
(Cortex-A7) that the DCIMVAC is executed on.

We should follow the linux dma follow. Before DMA read, first
invalidate dcache then after DMA read, invalidate dcache again.

With the DMA direction DMA_FROM_DEVICE, the dcache need be
invalidated again after the DMA completion. The reason is
that we need explicity make sure the dcache been invalidated
thus to get the DMA'ed memory correctly from the physical memory.
Any cache-line fill during the DMA operations such as the
pre-fetching can cause the DMA coherency issue, thus CPU get the stale data.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-07-26 12:17:20 +02:00
Daniel Kochmański
645c48f50e sunxi: Create helper function veryfing valid boot signature on MMC
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.

Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.

Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-24 16:17:08 +02:00
Daniel Kochmański
1b26bab12e mmc: Protect mmc_initialize from initialising mmc multiple times
`mmc_initialize` might be called multiple times leading to the mmc-controllers
being initialised twice, and initialising the `mmc_devices` list head twice
which may lead to memory leaks.

Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-24 16:17:08 +02:00
Simon Glass
8e6cc46178 dm: test: Add a test for the mmc uclass
Add a test to confirm that we can probe this device. Since there is no
MMC stack support in sandbox at present, this is as far as the test goes.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:32 -06:00
Simon Glass
1169299135 mmc: Add debug() output on read errors
Allow read errors to be diagnosed more easily.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:25 -06:00
Simon Glass
e7ecf7cb5a dm: mmc: Add an MMC uclass
Add basic support for MMC, providing a uclass which can set up an MMC
device. This allows MMC drivers to move to using driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:25 -06:00
Stefan Roese
492d3223b0 mmc: sdhci.c: Add config option to use a fixed buffer for transfers
While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the
following problem occured. The SPL runs in internal SRAM which is
the L2 cache locked to memory. When the MMC buffers now are located
on the stack (or bss), the SDIO controller (SDHCI) can't write into
this L2 cache memory.

This patch introduces a method to use a fixed buffer that will be
used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER.
This way, the board can use this buffer address located in SDRAM
for all transfers. This solves this SPL problem on the A38x and
should only be used in the SPL U-Boot version.

Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10 14:54:05 +02:00
Stefan Roese
29905a451b mmc: sdhci: Use timer based timeout detection in sdhci_send_command()
The loop counter based timeout detection does not work on the Armada
38x based board (DB-88F6820-GP). At least with dcache enabled a
timeout is detected. Without dcache enabled, the timeout does not
occur. Increasing the loop counter solves this issue. But a better
solution is to use a timer based timeout detection instead. This
patch now implements this timer based detection.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10 14:54:00 +02:00
Marek Vasut
9f1b4456c9 mmc: bcm2835_sdhci: Restore original delay behavior
Patch 33fe2fb8df titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.

Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
2015-06-25 17:04:37 -04:00
Tom Rini
180f87fcc5 mmc_write.c: Make mmc_berase do 32bit safe 64bit math
We want to see if the requested start or total block count are
unaligned.  We discard the whole numbers and only care about the
remainder.  Update the code to use div_u64_rem here and add a comment.

Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
2015-06-18 16:11:41 -04:00
Hans de Goede
1c09fa38e0 sunxi: mmc: Enable pull-up on card-detect gpio pin
On some boards we need to enable the internal pull-up te reliable detect
that no card is inserted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-04 14:08:28 +02:00
Tom Rini
d81572c272 Merge git://git.denx.de/u-boot-mpc85xx 2015-05-05 14:57:23 -04:00
Tom Rini
ff7e9cfc33 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2015-05-05 07:00:38 -04:00
Marek Vasut
33fe2fb8df ARM: mmc: bcm283x: Remove get_timer_us() from mmc driver
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
2015-05-05 12:29:42 +03:00
Simon Glass
707ac1ad17 tegra: mmc: Set the removable flag correctly
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-05 12:29:42 +03:00
Alexander Stein
ebe78bb993 mmc: bcm2835_sdhci: Use calloc to allocate bcm2835_sdhci_host
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.

Signed-off-by: Alexander Stein <alexanders83@web.de>
2015-05-05 12:29:42 +03:00
Yangbo Lu
253d5bdd64 mmc: fsl_esdhc: update eMMC44 adapter card erase timeout
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
2015-05-05 12:29:42 +03:00
Kevin Liu
5e1c23cd39 mmc: sdhci: add timeout setting for response busy command
Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-05-05 12:29:42 +03:00
Rob Herring
5a20397b00 mmc: remove the MMC_MODE_HC flag
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-05-05 12:29:36 +03:00
Andrew Gabbasov
bd47c13583 mmc: Fix splitting device initialization
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.

Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:46 +03:00
Andrew Gabbasov
1677eef459 mmc: Restructure polling loops to avoid extra delays
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.

Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:00 +03:00
Andrew Gabbasov
cc17c01f2d mmc: Continue polling MMC card for OCR only if it is still not ready
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:40 +03:00
Andrew Gabbasov
5289b5350b mmc: Do not pass external mmc_cmd structure to mmc_send_op_cond_iter()
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:09 +03:00
Andrew Gabbasov
a626c8d418 mmc: Avoid extra duplicate entry in mmc device structure
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:53:52 +03:00
Yangbo Lu
2d9ca2c72c mmc: fsl_esdhc: Add peripheral clock support
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:39 -07:00
Yangbo Lu
5a8dbdc6b4 mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:19 -07:00
Hans de Goede
90641f82f1 sunxi: mmc: Fix card-detect gpio handling to work with the driver-model
The driver-model gpio functions may return another value then -1 as error,
make the sunxi mmc code properly handle this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:52 +02:00
Hans de Goede
44d8ae5b69 sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Siva Durga Prasad Paladugu
eddabd1662 zynqmp: sdhci: Remove the quirk SDHCI_QUIRK_NO_CD
Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29 11:19:03 +02:00
Yangbo Lu
8b06460e55 ls2085a: esdhc: Add esdhc support for ls2085a
This patch adds esdhc support for ls2085a.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:51 -07:00
Masahiro Yamada
d6c418e4b8 ARM: bcm283x: move SoC headers to mach-bcm283x/include/mach
Move arch/arm/include/asm/arch-bcm283x/*
  -> arch/arm/mach-bcm283x/include/mach/*

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2015-03-28 09:03:09 -04:00
Rob Herring
3a48944bc9 mv_sdhci: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-03-18 09:56:17 +02:00
Rob Herring
3c1fcb770b sdhci: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-03-18 09:55:59 +02:00
Matt Reimer
e113fe3c06 mmc: sdhci: don't clobber adjacent registers
SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it
as if it were a long, as that would result in clobbering the three
registers following.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
2015-03-18 09:53:01 +02:00
Matt Reimer
8ebde4f0b3 mmc: s5p: properly mask SELBASECLK
Properly mask SELBASECLK by using an actual mask rather than the
number of bits to shift in order to create the mask.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-03-18 09:51:56 +02:00
Peng Fan
323aaaa1e3 mmc: fsl_esdhc fix register offset
Commit f022d36e8a introduces
error register offset.

Change the "char reserved3[59]" to "char reserved3[56]".

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-17 09:09:47 -04:00
Stefano Babic
b9cb64825b Merge branch 'master' of git://git.denx.de/u-boot 2015-03-02 09:42:53 +01:00
Volodymyr Riazantsev
0e1bf614d5 mmc: fsl_esdhc: Add support for DDR mode
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.

Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:11:10 -08:00
Matt Reimer
f88a429f11 mmc: sdhci: fix bus width switching on Samsung SoCs
Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on
Samsung SoCs using SDHCI_QUIRK_USE_WIDE8.  These SoCs report controller
version 2.0 yet they support 8-bit bus widths.  If 8-bit mode was
previously enabled and then an operation like "mmc dev" caused a switch
back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures.

This problem was manifested by "mmc dev" timing out.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
2015-02-23 19:52:00 +02:00
Przemyslaw Marczak
34dd928492 mmc: print SD/eMMC type for inited mmc devices
Depending on the boot priority, the eMMC/SD cards,
can be initialized with the same numbers for each boot.

To be sure which mmc device is SD and which is eMMC,
this info is printed by 'mmc list' command, when
the init is done.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-02-23 19:49:49 +02:00
Przemyslaw Marczak
64029f7aee mmc: exynos dwmmc: check boot mode before init dwmmc
Before this commit, the mmc devices were always registered
in the same order. So dwmmc channel 0 was registered as mmc 0,
channel 1 as mmc 1, etc.
In case of possibility to boot from more then one device,
the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device.

This can be achieved by init boot device as first, so it will be
always registered as mmc 0. Thanks to this, the 'saveenv' command
will work fine for all mmc boot devices.

Exynos based boards usually uses mmc host channels configuration:
- 0, or 0+1 for 8 bit  - as a default boot device (usually eMMC)
- 2 for 4bit - as an optional boot device (usually SD card slot)

And usually the boot order is defined by OM pin configuration,
which can be changed in a few ways, eg.
- Odroid U3     - eMMC card insertion -> first boot from eMMC
- Odroid X2/XU3 - boot priority jumper

By this commit, Exynos dwmmc driver will check the OM pin configuration,
and then try to init the boot device and register it as mmc 0.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
2015-02-23 19:49:22 +02:00
Hans de Goede
1f3e877def sunxi: mmc: Always declare High Capacity capability
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this
capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13
tablet, so always set it thereby fixing this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-23 19:46:13 +02:00
Jaehoon Chung
5dab81cea5 mmc: exynos_dw_mmc: use the exynos specific data structure
Clksel value is exynos specific value.
It removed "clksel_val" into dwmci_host and created the
"dwmci_exynos_priv_data" structure for exynos specific data.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:39:51 +02:00
Jaehoon Chung
3a33bb1874 mmc: exynos_dw_mmc: set to clksel_val into board-init function
"clksel_val" is assigned to property of mmc or defined value.
But it doesn't write at initial sequence.
There is a reason that get the wrong source-clock value.
This patch fixed it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:36:55 +02:00
Jaehoon Chung
afc9e2b509 mmc: dw_mmc: fixed the wrong bit control
If mode is not DDR-mode, then it needs to clear it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:35:13 +02:00
Otavio Salvador
ee0c538951 mmc: fsl_esdhc: Add support to force VSELECT set
Some boards cannot do voltage negotiation but need to set the VSELECT
bit forcely to ensure it to work at 1.8V.

This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-02-23 09:11:42 +01:00
Otavio Salvador
f022d36e8a mmc: fsl_esdhc: Add CMD11 support to switch to 1.8V
This adds support to switch to 1.8V in case CMD11 succeeds.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-02-23 09:11:42 +01:00
Simon Glass
91785f70b9 x86: mmc: Move common FSP functions into a common file
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.

This creates a generic PCI MMC device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-06 12:07:36 -07:00
Tom Rini
37ffffb98d Merge branch 'master' of git://git.denx.de/u-boot-ti 2015-02-02 12:37:34 -05:00
Tom Rini
be8ddad9c8 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2015-02-02 10:11:44 -05:00
Siarhei Siamashka
5abdb156bb sunxi: mmc: Add 'sunxi_' prefix to the static functions
This results in a much more readable callgraph, because now they
can't be confused with the function having exactly the same name
in the generic mmc code.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 14:04:28 +01:00
Simon Glass
0347960b87 dm: mmc: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Albert ARIBAUD \(3ADEV\)
5bfdd1fc97 omap3: mmc: add 1.8v bias setting for MMC1
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-01-29 12:00:50 -05:00
Tom Rini
3b95288a2a Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-01-23 10:22:29 -05:00
Hans de Goede
daf22636c2 sunxi: mmc: Add support for sun9i (A80)
The clocks on the A80 are hooked up slightly different, add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
5b8d7fb4fe sunxi: mmc: Use a realistic timeout when sending a mmc command
Wait 1 second for the sdcard to respond, rather then waiting for
0xfffff milliseconds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Michal Simek
38cd2d9c9b mmc: zynq: Use phys_addr_t for addresses
phys_addr_t is designed for physical addresses that's why
use it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-21 10:30:43 +01:00
Andrew Gabbasov
fc5b32fbf3 mmc: Skip changing bus width for MMC cards earlier than version 4.0
Wider bus widths (larger than default 1 bit) appeared in MMC standard
version 4.0. So, for MMC cards of any earlier version trying to change
the bus width (including ext_csd comparison) does not make any sense.
It may work incorrectly and at least cause unnecessary timeouts.
So, just skip the entire bus width related activity for earlier versions.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-01-19 17:41:52 +02:00
Andrew Gabbasov
bf4770731c mmc: Avoid redundant switching to 1-bit bus width for MMC cards
If all the commands switching an MMC card to 4- or 8-bit bus width fail,
and the bus width for the controller and the driver is still set
to default 1 bit, there is no need to send one more command to switch
the card to 1-bit bus width. Also, if the card or host controller do not
support wider bus widths, there is no need to send a switch command at all.

However, if one of switch commands succeeds, but the subsequent ext_csd
fields comparison fails, the card should be switched to some other bus width
(next in the list for the loop), or to default 1-bit bus width as a last
resort. That's why it would be incorrect to just remove the 1-bit bus width
case from the list, it should still be processed in some cases.

panto: Minor cosmetic edit removing superfluous parentheses.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-01-19 17:41:52 +02:00
Diego Santa Cruz
9e41a00b57 mmc: extend mmcinfo output to show partition write reliability settings
This extends the mmcinfo hardware partition info output to show
partitions with write reliability enabled with the "WRREL" string.
If the partition does not have write reliability enabled the "WRREL"
string is omitted; this is analogous to the ehhanced attribute.

Example output:

Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
Erase Group Size: 8 MiB
HC WP Group Size: 16 MiB
User Capacity: 13.8 GiB ENH WRREL
User Enhanced Start: 0 Bytes
User Enhanced Size: 512 MiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH WRREL
GP2 Capacity: 64 MiB ENH WRREL

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:51 +02:00
Diego Santa Cruz
8dda5b0e60 mmc: extend the mmc hardware partitioning API with write reliability
The eMMC partition write reliability settings are to be set while
partitioning a device, as per the eMMC spec, so changes to these
attributes needs to be done in the hardware partitioning API.
This commit adds such support.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:51 +02:00
Diego Santa Cruz
ac9da0e08c mmc: add API to do eMMC hardware partitioning
This adds an API to do hardware partitioning on eMMC devices. The
new mmc_hwpart_config() function does the partitioning in one go.
As the different attributes and partitioning options on eMMC may
be interdependent validation has to be done based on the complete
partitioning configuration. The function accepts three modes:

- MMC_HWPART_CONF_CHECK: just validates that the configuration
  is valid.
- MMC_HWPART_CONF_SET: validates and sets all the fields in
  EXT_CSD but without setting the "partitioning completed" bit,
  and thus is reversible.
- MMC_HWPART_CONF_COMPLETE: does everything and is thus not
  reversible.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:45 +02:00
Diego Santa Cruz
9cf199ebcf mmc: the ext_csd data may be used during init even if reading failed
The mmc_startup() function uses the ext_csd data even if reading it
from the mmc device failed. This bug was introduced in commit
bc897b1d4d. We now bail out if
reading it fails, this should not be a problem as ext_csd was
introduced in MMC 4.0 and this code is conditional on MMC >= 4.0.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:04:48 +02:00
Diego Santa Cruz
8a0cf49010 mmc: eMMC partitioning data is not effective till partitioning completed
The eMMC spec says that partitioning is only effective after the
PARTITION_SETTING_COMPLETED is set in EXT_CSD (and a power cycle was done,
but that we cannot know). Thus the partition sizes and attributes should
be ignored when that bit is not set, otherwise the various capacities
are not coherent (e.g., the user data capacity will be that of the
unpartitioned device while partition sizes would be non-zero).

Prescence of non-zero partitioning data is nevertheless still used to
activate the high-capacity size definitions (EXT_CSD_ERASE_GROUP_DEF)
as it is necessary to set that to write any of the partitioning fields
in EXT_CSD, so having partitioning data means someone previously
activated that and we should keep it activated.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:04:48 +02:00
Diego Santa Cruz
037dc0ab5d mmc: read the high capacity WP group size for eMMC
Read the eMMC high capacity write protect group size at mmc device
initialization. This is useful to correctly partition an eMMC device,
as partitions need to be aligned to this size.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
a4ff9f83f5 mmc: fix erase_grp_size computation with high-capacity size definition
The erase_grp_size in struct mmc is to be a size in 512-byte sectors
but the code used to compute it for eMMC when EXT_CSD_ERASE_GROUP_DEF is
enabled computed it as bytes, leading to erase sizes and alignment
much larger than what is actually required by the mmc device.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
a7f852b688 mmc: read the size of eMMC enhanced user data area
This modification reads the size of the eMMC enhanced user data area
upon initialization of an mmc device, it will be used later by
mmcinfo.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
f8e89d6716 mmc: computation of eMMC GP partition size was missing 512 KiB factor
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
0c453bb76c mmc: incomplete test to switch to high-capacity group size definitions
The eMMC spec mandates that the high-capacity group size definitions
should be enabled when the device is partitioned (by setting
ERASE_GROUP_DEF in EXT_CSD). The current test to determine when this is
required misses a few cases. In particular a device may have been
partitioned without setting the enhanced attribute on any partition
or partitioning may be completed without creating any extra partitions.

This change moves the code to set ERASE_GROUP_DEF to after reading
all partition information. It is also enabled when
PARTITIONING_SETTING_COMPLETED is set as it is necessary to enable
ERASE_GROUP_DEF before setting that bit, so it means that the user
previously switched to the high capacity definitions.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
c3dbb4f9b7 mmc: extend mmcinfo to show enhanced partition attribute
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.

The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:01:34 +02:00
Nobuhiro Iwamatsu
72d42bad58 mmc: rmobile: Add SDHC support for Renesas rmobile ARM SoC
This adds Renesas rmobile ARM SoC's SD/MMC host support.
This drivers tested with Gose board and Koelsch board.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-19 16:24:25 +02:00
Axel Lin
b0c4ae1a51 mmc: sunxi: Fix misuse of gpio_direction_input()
It does not make sense to make gpio_direction_input() return the gpio input
status. The return value of gpio_direction_input() is inconsistent if
CONFIG_DM_GPIO is defined.
And we don't need to call gpio_direction_input() int sunxi_mmc_getcd().
Just init the gpio once in mmc_resource_init() is enough.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
fc3a832576 sunxi: mmc: Properly setup mod-clk and clock sampling phases
The sunxi mmc controller has both an internal clock divider, as well as
the divider in the mod0-clk for the mmc controller.

The internal divider cannot be used, as it conflicts with the setting of
clock sampling phases which is done in the mod0-clk, so it must be set to
0 (divide by 1).

For some reason while the kernel has had this correct from day one, the
u-boot sunxi mmc code has been using a fixed mod0-clk and setting its
internal divider depending on the desired speed. This is something which
we've inherited from the original Allwinner u-boot sources, but while this
has been fixed in Allwinner's own u-boot code at least for the A23 and later
upstream u-boot was still doing this wrong.

This commit fixes this, thereby also fixing mmc support not working reliable
on the A23 (which seems more sensitive to this) and possible also fixes some
other sunxi mmc issues.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Gerald Kerma
ac0b729844 MVEBUMMC : REMOVE unnecessary delay from init
Remove unnessecary delay from mvebu_mmc_initialize

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:28 +02:00
Gerald Kerma
02b2739e8f MVEBUMMC : CLEAN code
Clean mvebu_mmc_send_cmd

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:23 +02:00
Gerald Kerma
86eeecafc2 MVEBUMMC : REMOVE unnecessary delays
Remove delays in mvebu_mmc_set_bus and mvebu_mmc_set_clk

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:16 +02:00
Gerald Kerma
fc0f25f919 MVEBUMMC : FIX debug strings
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:12 +02:00
Gerald Kerma
28d27b79e3 MVEBUMMC : Speed up access time
Get about 40x faster access on SHEEVAPLUG MMC
 Fix some SD type compatibility

 Changes in v3:
 - fix the HW_STATE (from linux mvsdio)
 - review delays and timeouts

 Changes in v2:
 - increase number of loops
 - remove initial delay

 Changes in v1:
 - review all loops, delays and timeouts

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:04 +02:00
Gerald Kerma
2591fbdba3 MVEBUMMC : Change copyright date
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:09:45 +02:00
Andrew Gabbasov
2b8a9692f9 mmc: dw_mmc: Use active DDR mode flag
The card_caps bit should denote the card capability to use DDR mode,
but we need the flag indicating that the DDR mode is active.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:09:01 +02:00
Andrew Gabbasov
5af8f45cd0 mmc: Fix block length for DDR mode
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:38 +02:00
Andrew Gabbasov
201d5ac438 mmc: Fix Dual Data Rate capability recognition
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:21 +02:00
Andrew Gabbasov
786e8f818c mmc: Fix handling of bus widths and DDR card capabilities
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.

Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.

This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.

Also, some clean up is made with errors handling and code syntax layout.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:06 +02:00
Jaehoon Chung
dfcb683a31 mmc: exynos_dw-mmc: change debug message
To debug more exactly, add the index for device.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:35:30 +02:00
Markus Niebel
edab723b47 MMC: add MMC_VERSION_5_0
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:34:20 +02:00
Markus Niebel
d7b2912991 MMC: fix user capacity for partitioned eMMC card
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:28:04 +02:00
Lubomir Popov
e75eaf100b mmc: Cosmetic fix for nicer, aligned device list printout
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2014-12-12 20:08:47 +02:00
Tom Rini
98d2d5e8c4 Merge branch 'master' of git://git.denx.de/u-boot-ti 2014-12-08 16:35:06 -05:00
Paul Kocialkowski
aac5450ea9 omap_hsmmc: Board-specific TWL4030 MMC power initializations
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
2014-12-04 21:28:15 -05:00
Nobuhiro Iwamatsu
9675f61077 mmc: sh_mmcif: Add support rmobile
Renesas R-Mobile/R-Car ARM SoC of MMC has the same IP that are supported by
sh_mmcif. This adds support R-Mobile/R-Car ARM SoC with the setting of the
clock support.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-12-05 11:16:22 +09:00
Nobuhiro Iwamatsu
7a7eb983a4 mmc: sh_mmcif: Change maximum and minimum value of MMC clock
Maximum value and the minimum value of clock for sh_mmcif instead by
base of MMC clock. This removes fixed clock, make the changes to be calculated
according to environment.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-12-05 11:15:52 +09:00
Nobuhiro Iwamatsu
21ea350385 mmc: sh_mmcif: Use DIV_ROUND_UP and fls instead of calculation loop
Use DIV_ROUND_UP and fls to simplify the code.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-12-05 11:15:11 +09:00
Paul Kocialkowski
f3e85e4825 twl4030: device-index-specific MMC power initializations, common ramp-up delay
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:40 -05:00
Paul Kocialkowski
95de9ab201 mmc: Board-specific MMC power initializations
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:40 -05:00
Felipe Balbi
d11ac4b56d arm: omap: add support for am57xx devices
just add a few ifdefs around because this
device is very similar to dra7xxx.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:14 -05:00
Tom Rini
21008ad638 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Conflicts:
	drivers/mmc/fsl_esdhc.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-11-26 11:22:29 -05:00
Tom Rini
dee332ffb7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-11-24 12:02:12 -05:00
Masahiro Yamada
b41411954d linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does.  This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
 - Use min, max, min3, max3 only when the arguments have the same type
   (or add casts to the arguments)
 - Use min_t/max_t instead with the appropriate type for the first
   argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-23 06:48:30 -05:00
Ye.Li
a3d6e38617 mmc: fsl_esdhc: Update esdhc driver for iMX6SX
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20 10:44:42 +01:00
Markus Niebel
3b4b9a3377 mmc: fsl_esdhc: fix f_max retrieval during init
for multi instance API we use struct fsl_esdhc_cfg to
pass the clock rate. Do not set f_max from global data,
since this is wrong for multi instance case.

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-19 18:17:12 -08:00
Pavel Machek
389b89c70f sort drivers/mmc/Makefile
Sort drivers/mmc makefile, as requested by wd.

Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-11-07 16:27:04 -05:00
Igor Grinberg
0b03a931ab omap: hsmmc: assume cd gpio is active low
Switch the default CD GPIO polarity to active low.

The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.

Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.

This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.

This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06 11:04:41 -05:00
Hans de Goede
967325feb2 dm: sunxi: Request card detect gpio
This is necessary for the device-model enabled builds to work properly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-11-05 13:10:13 +01:00
Ian Campbell
ed41e62f51 sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?I
Mostly automatic with:
    sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05 13:09:58 +01:00
Przemyslaw Marczak
3f3c13a513 mmc: s5p: set SD detection pin as input
The SD Card slot detection pin should be configured as input.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-10-27 19:20:51 -06:00
Tom Rini
d0796defbe Merge http://git.denx.de/u-boot-sunxi 2014-10-26 14:13:24 -04:00
Tom Rini
84a6df09c7 Merge git://git.denx.de/u-boot-dm
Fix a trivial conflict over adding <dm.h>

Conflicts:
	arch/arm/cpu/armv7/omap3/board.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-10-26 14:03:08 -04:00
Jeroen Hofstee
74321944e6 mmc: bcm2835_sdhci: add missing include
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 15:27:35 -04:00
Jeroen Hofstee
19d7bf3d86 tegra: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:27:37 -04:00
Jeroen Hofstee
6588c78bf3 sdhci: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:02:02 -04:00
Chen-Yu Tsai
e637b30b9c mmc: sunxi: Add support for sun8i (A23)
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.

Re-use code added for sun6i.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:39 +02:00
Hans de Goede
e79c7c8810 sunxi: When we've both mmc0 and mmc2, detect from which one we're booting
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.

When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Hans de Goede
cd82113a98 sunxi: Add mmc card-detect functionality
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:38 +02:00
Hans de Goede
1d1bd42eb0 ARM: sunxi-mmc: Add mmc support for sun6i / A31
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
		rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24 09:35:37 +02:00
Wills Wang
a3e8c22011 mmc: sunxi: add SDHC support for sun6i/sun7i/sun8i
Allwinner A20/A23/A31's SD/MMC host support SDHC High Capacity feature.

Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-24 09:35:37 +02:00
Simon Glass
5915a2ad0d dm: omap: gpio: Support driver model
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.

Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23 19:29:07 -06:00
Tom Rini
03a3536c7b Merge branch 'master' of git://git.denx.de/u-boot-tegra 2014-10-23 14:05:34 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Simon Glass
7f1961018c dm: exynos: Make sure that GPIOs are requested
With driver model GPIOs must be requested before use. Make sure this is
done correctly.

(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:33 -06:00
Marcel Ziswiler
09fb73611f mmc: Tegra: Fix timeout issue seen on certain eMMC parts
During rigorous testing of our latest update infrastructure I came
across quite consistent timeouts on certain eMMC parts (e.g. Hynix
H26M21001ECR) when writing big (e.g. in excess of 400 MB) file system
images:

MMC write: dev # 0, block # 40960, count 944128 ...
 mmc_send_cmd_bounced: MMC Timeout
    Interrupt status        0x00000001
    Interrupt status enable 0xdfff003b
    Interrupt signal enable 0xdfff0002
    Present status          0x01870106
mmc write failed

Comparing the various data sheets I came across the following timeout
specification:

Secure Erase/TRIM Timeout=300ms*2*10=6000ms

Unfortunately empirical testing still failed albeit much more rarely.
Increasing the timeout to 8000ms made it finally disappear entirely.
This patch allows us writing various eMMC parts without seeing any
further issues.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-10-22 09:30:54 -07:00
Albert ARIBAUD
790af81543 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-10-11 01:20:30 +02:00
Simon Glass
311757be27 samsung: Enable device tree for s5p_goni
Change this board to add a device tree.

This also adds a pinmux header file although it is not used as yet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:47 +09:00
Tom Rini
04de09f89b Merge branch 'topic/arm/socfpga-20141006' of git://git.denx.de/u-boot-socfpga
Fix a trivial conflict in dw_mmc.c after talking with Marek.

Conflicts:
	drivers/mmc/dw_mmc.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-10-06 15:17:13 -04:00
Pavel Machek
498d1a62db arm: socfpga: mmc: Pick the clock from clock manager
Make the SoCFPGA MMC stub pick clock via the clock manager
frequency accessors instead of hard-coding the frequency.

Also fix calloc() misuse.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2014-10-06 17:46:49 +02:00
Pavel Machek
f33c930583 mmc: dw_mmc: cleanups
The dw_mmc driver was responding to errors with debug(). Change that
to prinf()/puts() respectively so that any errors are immediately
obvious. Also adjust english in comments.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:34:39 +02:00
Pavel Machek
b966db0d72 dw_mmc: cleanups
dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.

Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Mario Schuknecht
786a27b7ec mmc: Fix mmc bus width
After setting the bus width, the extended CSD register is read. Some selected
fields are compared with previously read extended CSD register fields. In this
comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is
previously written under certain circumstances. And then the comparison fails.

Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE
instead of field EXT_CSD_ERASE_GROUP_DEF.

Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Mario Schuknecht
bcd06989b8 mvebu_mmc: Driver addition
In function mvebu_mmc_write notice command timeout. It is possible that a
command is done, but a timeout occurred.

Enable timeout in set bus function.

Set window registers. Without that I could not use the driver on a Kirkwood
88F6282 SoC.

Set high capacity and 52MHz driver feature.

Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Peter Bigot
6dc93e7087 mmc: restore capacity when switching to partition 0
The capacity and lba for an MMC device with part_num 0 reflects the
whole device.  When mmc_switch_part() successfully switches to a
partition, the capacity is changed to that partition.  As partition 0
does not physically exist, attempts to switch back to the whole device
will indicate an error, but the capacity setting for the whole device
must still be restored to match the partition.

Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Hannes Petermaier
021a80559f mmc: fix ERASE_GRP_DEF handling
if we set manually this bit on the eMMC card using mmc_switch(...),
we also have to set it within our (before read) internal structure
'ext_csd'.

Otherwise following checks on this will fail.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-10-03 17:26:49 +03:00
Sonic Zhang
282a82e8a1 mmc: set correct block size value in bfin sdh driver
Wait data transfer till the data end bit other than the data block end
bit is set.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-10-03 17:26:49 +03:00
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Masahiro Yamada
ed36323f6d kconfig: add blank Kconfig files
This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00
Wang Huan
19060bd886 ls102xa: esdhc: Add esdhc support for LS102xA
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.

For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:34 -07:00
Pavel Machek
7860649716 socfpga: cleanup socfpga_dw_mmc
Cleanups as suggested by wd on mailing list.

Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-08-30 07:46:38 -04:00
Pavel Machek
51fb455f82 socfpga: fix clock manager register definition
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.

This fixes structure to match hardware.

Signed-off-by: Pavel Machek <pavel@denx.de>
2014-08-29 15:50:50 -04:00
Bo Shen
da55c66ec9 MMC: atmel_mci: enable high speed mode support
If the MCI IP version >= 0x300, it supports hight speed mode
option, this patch enable it.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 20:01:33 +03:00
Bo Shen
cd60ebd430 MMC: atmel_mci: refactor setting the mode register
The mode register is different between MCI IP version.
So, according to MCI IP version to set the mode register.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 20:01:09 +03:00
Chin Liang See
6ace153d13 mmc/dw_mmc: Fix clock divider calculation error for bypass mode
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
2014-08-01 19:45:32 +03:00
Marek Vasut
dae0f5c644 mmc: s3c: Add SD driver
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 19:24:34 +03:00
Lubomir Rintel
64973023df bcm2835_sdhci: Add SDHCI_QUIRK_NO_HISPD_BIT flag
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
2014-08-01 18:57:02 +03:00
DrEagle
3fe3b4fb1c ARM: kirkwood: add mvsdio driver
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.

Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 18:44:56 +03:00
Albert ARIBAUD
740f41d3cb Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-07-28 10:12:45 +02:00
Jeroen Hofstee
750121c350 mmc: prevent some warnings with make W=1
Add missing prototypes for global functions and
make local functions static.

cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-18 17:53:24 -04:00
Jeroen Hofstee
cee9ab7cb6 dirvers: mmc: use __weak
use weak instead of alias to prevent some clang warnings.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-18 17:53:23 -04:00
Hans de Goede
b6ae6765c5 sunxi: Remove mmc DMA support
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.

Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Jeroen Hofstee
2b9912e6a7 includes: move openssl headers to include/u-boot
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.

cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-19 11:19:04 -04:00
Darwin Rambo
3d6a5a4dfc mmc: free allocated memory on initialization errors
Cleanup to balance malloc/free calls.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-06-12 15:21:12 +03:00
Stephen Warren
d4622df342 mmc: return meaningful error codes from mmc_select_hwpart
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.

Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-06-12 14:15:59 +03:00
Albert ARIBAUD
cc49da249c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-06-02 08:43:48 +02:00
Wu, Josh
9902c7b6f1 mmc: atmel_mci: fix print incorrect buffer content for debug
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix checkpatch line length warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-05-27 00:10:46 +02:00
Ian Campbell
e24ea55c04 sunxi: mmc support
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > +	case 1:
> > +#if CONFIG_MMC1_PG

> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?

It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...

> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.

...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.

> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>

Thanks!

8<---------------------------------

>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support

This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:26:43 +02:00
Tom Rini
10dc77716f esdhc/usdhc: Fix warning when CONFIG_SYS_FSL_ESDHC_USE_PIO is not set
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO.  Only define this function
in this case as well.

Signed-off-by: Tom Rini <trini@ti.com>
2014-05-23 09:19:05 -04:00
Tom Rini
638b3e8342 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2014-05-23 08:13:59 -04:00
Stephen Warren
d235628434 mmc: provide a select_hwpart implementation for get_device()
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-23 12:11:44 +03:00
Pierre Aubert
91fdabc67a eMMC: add support for operations in RPMB partition
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
2014-05-23 11:52:51 +03:00
Andrew Gabbasov
6b2221b008 mmc: Handle switch error status bit in MMC card status
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-05-23 11:34:33 +03:00
Mateusz Zalega
d803fea576 mmc: postponed needless timer initialization
mmc_init() doesn't call get_timer() anymore if MMC is already
initialized.

<panto> Minor formatting fix.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
2014-05-23 11:19:53 +03:00
Ye.Li
716897760f esdhc/usdhc: Fix PIO mode bug in fsl_esdhc driver
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.

Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
2014-05-22 18:52:45 +03:00
Albert ARIBAUD
05d134b084 Merge remote-tracking branch 'u-boot/master'
Conflicts:
	boards.cfg

Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
2014-05-20 10:05:42 +02:00
Jaehoon Chung
9b8c9a3c09 mmc: s5p_sdhci: add the s5p_sdhci_core_init function
To reuse the code, added the s5p_sdhci_core_init function.
Before applied this patch, didn't use the 8-bit mode at exynos baord.
Because it didn't set "MMC_MODE_8BIT".

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
e09bd85329 mmc: exynos_dw_mmc: enable the DDR mode
Set the ddr mode capability by default.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
045bdcd0b2 mmc: dw_mmc: support the DDR mode
Support the DDR mode at dw-mmc controller

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
d22e3d46a9 mmc: support the DDR mode for eMMC
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
8caf46d189 mmc: remove the unnecessary define and fix the wrong bit control
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Lukasz Majeski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
959198f7ca mmc: exynos_dw_mmc: restore the property into host
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Stephen Warren
f175603f7c ARM: tegra: set CONFIG_SYS_MMC_MAX_DEVICE
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.

A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE

1) It isn't documented in README. The same is true for a lot of similar
   defines used by api_storage.c.

2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
   valid values are 0..n-1 not 0..n.

However, I this patch does not address those shortcomings.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
Chunhe Lan
0b2e13d9cc powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
2014-05-13 08:24:32 -07:00
Prabhakar Kushwaha
1eaa742d85 driver: Add support of image load for MMC & SPI in SPL
Add support of loading image, binary for MMC and SPI during SPL boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:50 -07:00
Prabhakar Kushwaha
613ab32c47 driver/mmc: fix compile warnings
Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Albert ARIBAUD
519fdde9e6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	include/configs/trats.h
	include/configs/trats2.h
	include/mmc.h
2014-04-08 09:25:08 +02:00
Haijun.Zhang
1336e2d343 mmc:eSDHC: Workaround for data timeout issue on Txxx SoC
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.

2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.

* Update of patch for change mmc interface by
	Pantelis Antoniou <panto@antoniou-consulting.com>

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:25:01 +03:00
Andrew Gabbasov
8a573022c3 mmc: fsl_esdhc: add controller reset in case of data related errors too
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:17:12 +03:00
Andrew Gabbasov
fb823981c5 mmc: fsl_esdhc: fix calculation of timeout for data transactions
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:16:56 +03:00
Tom Rini
33ace362fd mmc: Add 'mmc rst-function' sub-command
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work.  Details on this being
required will be part of the eMMC datasheet.  Also add using this
command to the dra7xx README.

* Whitespace fix by panto

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:02:58 +03:00
Nobuhiro Iwamatsu
74c32ef58d mmc: sh_mmcif: Fix warning by unused variable
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 12:55:48 +03:00
Nobuhiro Iwamatsu
cd2bf4846c mmc: sh_mmcif: Fix compile error
BY commit "mmc: Split mmc struct, rework mmc initialization (v2)",
sh_mmcif has compile error. This fixes compile error.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 12:55:31 +03:00
Tom Rini
0b2da7e209 blackfin: mmc: Correct mmc_host_is_spi and bfin_sdh.c
In the recent mmc cleanup, the mmc_host_is_spi macro was broken and
bfin_sdh.c had mmc->bus_width turned into mmc_bus_width(mmc), both of
which were incorrect.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-28 16:55:29 -04:00
Pantelis Antoniou
93bfd61677 mmc: Split mmc struct, rework mmc initialization (v2)
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.

On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.

Typically the initialization got something like this in every driver.

	struct mmc *mmc = malloc(sizeof(struct mmc));
	memset(mmc, 0, sizeof(struct mmc);
	/* fill in fields of mmc struct */
	/* store private data pointer */
	mmc_register(mmc);

By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:

	struct mmc = mmc_create(&cfg, priv);

All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.

Changes since v1:

* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 12:58:56 +02:00
Pantelis Antoniou
22cb7d334e mmc: Convert mmc struct's name array to a pointer
Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 11:32:10 +02:00
Pantelis Antoniou
ab769f227f mmc: Remove ops from struct mmc and put in mmc_ops
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.

This makes the mmc structure smaller as well as conserving
code space (in theory).

All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.

Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 11:32:10 +02:00
Piotr Wilczek
3577fe8be9 drivers:mmc:sdhci: enable support for DT
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:54:59 +09:00
Michal Simek
345d3c0f01 mmc: zynq: Add OF initialization support
Enable initialize sdhci from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:35 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Darwin Rambo
7a9d0ad009 mmc: kona: Add Kona mmc driver
Add support for the Kona SDHCI found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:41 +01:00
Tom Rini
130fbeb1c5 blackfin: Add <asm/clock.h> to numerous drivers
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-20 12:00:27 -05:00
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Tom Rini
614b2bf1c9 cmd_mmc.c: Drop open/close mmc sub-commands
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform.  Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.

Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
5a99b9de1a cmd_mmc.c: Add bootbus mmc sub-command
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).

Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
792970b0a3 cmd_mmc.c: Add 'partconf' command to mmc
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]).  Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.

Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Siva Durga Prasad Paladugu
f9ec45d1d9 mmc: Enabled quirk SDHCI_QUIRK_BROKEN_R1B
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207b)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:47:19 +02:00
Rajeshwari S Shinde
d3e016cc28 MMC: DWMMC: Correct the CLKDIV register value
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)

Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.

This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:42:26 +02:00
Stephen Warren
def816a2ba mmc: set rca to 1 for MMC cards
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:34:06 +02:00
Stephen Warren
a73ca4789f mmc: tegra: support Tegra124
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.

However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.

That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:45 -07:00
Masahiro Yamada
4d764244bd drivers: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:07 -05:00
Haijun.Zhang
d47e3d2707 esdhc: Detecting 8 bit width before mmc initialization
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:34 -08:00
Haijun.Zhang
f7e27cc5ee esdhc: Workaround for card can't be detected on T4240QDS
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
   For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.

This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:15 -08:00
Minkyu Kang
a4d481ed81 mmc: dwmmc: mode change to 0644
Don't know why but, file permission was changed

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-14 09:44:21 -05:00
Chin Liang See
c5c1af2176 socfpga/dwmmc: Adding DesignWare MMC driver support for SOCFPGA
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-09 11:53:55 +02:00
Markus Niebel
ab71188ce8 mmc: add setdsr support
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.

Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)

Following proposal for an implementation:

- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set

Additionally the mmc command is extended to make is possible to play around with different
DSR values.

The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-09 11:47:51 +02:00
Darwin Rambo
30e6d979fa mmc: Minor cleanup of sdhci.c
Fixup prints to show where the print is done from, and
a few minor formatting/grammar issues.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-09 11:36:56 +02:00
Alexey Brodkin
2a7a210e2c mmc/dwmmc: use bounce buffer for data exchange between CPU and MMC controller
Bounce buffer implementation takes care of proper data buffer alignemt
and correct flush/invalidation of data cache at once so we no longer
depend on input data variety and make sure CPU and MMC controller deal
with expected data in case of enabled data cache.

Bounce buffer requires to add its definition (CONFIG_BOUNCE_BUFFER) in
board configuration, otherwise corresponding library won't be compiled
and linker will fail to build resulting executable.

Difference since v1 - fixed compile-time warning with type casting to
"void *":

Slight edit to remove UTF8 characters in the commit message.

Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

====
passing argument 2 of 'bounce_buffer_start' discards 'const' qualifier
from pointer target type
====

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@gmail.com>
2014-01-09 11:29:02 +02:00
Chin Liang See
fd26b5490b mmc/dwmmc: Using calloc instead malloc
To enhance the SDMMC DesignWare driver to use calloc instead of
malloc. This will avoid the incident that uninitialized members
of mmc structure are later used for NULL comparison.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-08 19:02:41 +02:00
Kuo-Jung Su
adebb98ba1 mmc: add Faraday FTSDC021 SDHCI controller support
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.

However this driver is only verified with SD memory cards.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
2013-12-08 14:23:05 +02:00
Priyanka Jain
4520a2f28e powerpc: mmc: Add corenet devices support in esdhc spl
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.

So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-12-08 14:17:28 +02:00
Alexey Brodkin
9108b315f2 mmc/dwmmc: modify FIFO threshold only if value explicitly set
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.

This implementation allows:
 * escape unclear and recursive calculations that are currently in use
 * use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-12-08 14:08:47 +02:00
Jaehoon Chung
18ab675597 mmc: dw_mmc: remove the exynos specific code in dw-mmc.c
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-08 14:07:07 +02:00
Masahiro Yamada
710f1d3d5f drivers: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:26:01 -04:00
Haijun.Zhang
ef38f3ffb9 powerpc/esdhc: Add 3.3v voltage support in esdhc capacity register
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:34 +02:00
Haijun.Zhang
a54d681132 esdhc: memset mmc struct before putting into use
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.

Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.

Test on P5040 and T4240,
Error Log:

=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:34 +02:00