The initialization function calls a nand_chip.scan_bbt(mtd) but
scan_bbt is never initialized resulting in an undefined function
pointer. This will direct the function pointer to nand_default_bbt
defined in the same file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
When building mxc_spi driver on ARM64 platforms, get below build warnings.
Fix it in this patch.
In file included from include/common.h:48:0,
from drivers/spi/mxc_spi.c:9:
drivers/spi/mxc_spi.c: In function ‘spi_xchg_single’:
drivers/spi/mxc_spi.c:232:21: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
_func_, bitlen, (u32)dout, (u32)din);
^
include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
^~~~~
drivers/spi/mxc_spi.c:232:32: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
_func_, bitlen, (u32)dout, (u32)din);
^
include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
^~~~~
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The pinctrl supports to set any bit in input register on iMX6 if
the MSB of input value is 0xff. But the driver uses signed int for
input value, so when executing the codes below, it won't meet.
Because this is arithmetic right shift.
if (input_val >> 24 == 0xff)
Fix the issue by changing the input_val, config_val and mux_mode to u32.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently if we have more than one phy on the MDIO bus, we do not have a
good mechanism for determining which should be used at runtime. Enable the
FEC driver to determine the address for the PHY from the device tree.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Linux kernel binding is using atmel,24c08 compatible string. On the
other hand there is atmel,24c08a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
These eeproms are available on several ZynqMP development boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Do this by using $(SPL_) in Makefiles and CONFIG_IS_ENABLED in C code.
This ensures the files and features are only built into the right build
for which they are enabled. Using the macros to simplify this patch was
made possible by the config symbol rename done in the last patch.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It is not possible to link the SPL image when CONFIG_GPIO is enabled
but CONFIG_SPL_GPIO is not. Use the IS_ENABLED macro instead to
correctly check whether CONFIG_{SPL_}GPIO is enabled.
This commit fixes the following errors:
* undefined reference to `dm_gpio_get_value
* undefined reference to `gpio_request_by_name'
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[trini: Move guard to fix warning in msdc_ops_get_wp()]
Signed-off-by: Tom Rini <trini@konsulko.com>
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Apparently we never allocated buffer for arc_serial_platdata
which for some reason never caused problems when executed in nSIM.
But in Qemu this causes expected problems.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Print information about Aquantia system interface and firmware loaded
on the phy.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If System Interface protocol is USXGMII then enable USXGMII autoneg
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the datasheet to access the extended registers we have to:
1. Write Register 31 Data = 0x0XYZ (Page 0xXYZ)
2. Read/Write the target Register Data
3. Write Register 31 Data = 0x0000 or 0xa42 (switch back to IEEE
Standard Registers)
Hook the missing functions so that we can use the `mdio rx/wx` command to
easily access the extended registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch add GPIO configuration support in mvneta driver.
Driver will handle PHY reset. GPIO pins should be set in device tree.
Ported from mvpp2x
[https://patchwork.ozlabs.org/patch/799654/]
Initial discussion to port the changes into mvneta
[https://patchwork.ozlabs.org/patch/1005765/]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some existing device trees don't specify a phy-mode so fallback to GMII
when a phy-mode is not provided.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For KSZ9021, all skew register fields are 4-bit wide.
For KSZ9031, the clock skew register fields are 5-bit wide.
The common code in ksz90x1_of_config_group calculating the combined
register value checks if the requested value is above the maximum
and uses this maximum if so. The calculation of this maximum uses
the register width, but the check itself does not. It uses a hardcoded
value of 0xf, which is too low in case of the 5-bit clock (0x1f).
This detail was probably lost during driver unification.
Effect (only for KSZ9031 clock skews): For values greater 900 (== 0ps),
this silently results in 1860 (== +960ps) instead of the requested one.
Fix the check by using the bit width instead of hardcoded value(s).
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code forces all ports on a given Ethernet device to use the same
mdio device. In practice different ports might be wired to separate mdio
devices. Move the mdio device from the container struct mvpp2 to the per
port struct mvpp2_port.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current mdio base lookup code relies on a 'reg' property at the upper CP
node. There is no 'reg' property there in current DT files of Armada
CP110. Use ofnode_get_addr() instead since it provides proper DT address
translation.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Short frames are padded to the minimum allowed size of 60 bytes.
However, the designware driver sends old data in these padding bytes.
It is common practice to zero out these padding bytes ro prevent
leaking memory contents to other hosts.
Fix the padding code to zero out the padded bytes at the end.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The designware driver has a bug in setting the tx length into the dma
descriptor: it always or's the length into the descriptor without
zeroing out the length mask before.
This results in occasional packets being transmitted with a length
greater than they should be (trailer). Due to the nature of Ethernet
allowing such a trailer, most packets seem to be parsed fine by remote
hosts, which is probably why this hasn't been noticed.
Fix this by correctly clearing the size mask before setting the new
length.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phy devices can be accessed via clause 22 or via clause 45.
This information can be deduced when we read phy id. if the phy id
is read without giving any MDIO Manageable Device Address (MMD), then
it conforms to clause 22. otherwise it conforms to clause 45.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update cadence i2c driver to support livetree
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When FPGA programming fails, it does so silently, unless debugging
code is enabled. This makes it hard to detect problems in production
environments.
Print the error message unconditionally so the error doesn't go
unnoticed.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves fixed-link functionality code to a separate
routine inorder to make it more modular and cleaner.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This variable was incorrectly added by:
"mmc: zynq_sdhci: Add support for SD3.0"
(sha1: d1f4e39d58)
which had nothing to do with MMC power sequence provider.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for nand multi chip select.
Also adding CONFIG_SYS_NAND_MAX_CHIPS to Kconfig to specify maximum number
of nand chips.
Signed-off-by: Tummala Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Serval SoC family has 32 pins. Currently there is no
support for Serval in Linux kernel.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The Servalt SoC family has 36 pins. Currently there is not support
for Servalt pinctrl in Linux kernel.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This patch adds support for the Microsemi Ethernet switch present on
Ocelot SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
The Armada 37xx watchdog driver was recently accepted for mainline
kernel by watchdog subsystem maintainer, but the driver works a little
different than the one in U-Boot. This patch fixes this.
In the previous implementation there was a tiny period of time when the
watchdog was disabled and the system was vulnerables - this was during
pinging, which was done by disabling, setting, and enabling the counter.
Now pinging is done without disabling the watchdog. We use 2 counters:
Counter 1 is the watchdog counter - on expiry, the system is reset.
Counter 0 is used to reset Counter 1 to start counting from the set
timeout again. So Counter 1 is set to be reset on Counter 0 expiry event
event and pinging is done by forcing an immediate expiry event on
Counter 0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on musb driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on phy driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add initial clock driver for Allwinner A80.
- Implement UART bus clocks via ccu_clk_gate table for
A80, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement UART bus resets via ccu_reset table for A80,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add initial clock driver for Allwinner H6.
- Implement UART bus clocks via ccu_clk_gate table for
H6, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement UART bus resets via ccu_reset table for H6,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Implement UART resets for all relevant Allwinner SoC
clock drivers via ccu reset table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Implement UART clocks for all Allwinner SoC
clock drivers via ccu clock gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add initial clock driver for Allwinner V3S.
- Implement USB bus and USB clocks via ccu_clk_gate table
for V3S, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for V3S, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner R40.
- Implement USB bus and USB clocks via ccu_clk_gate
for R40, so it can accessed in common clk enable
and disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for R40, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A83T.
- Implement USB bus and USB clocks via ccu_clk_gate table
for A83T, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for A83T, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A23/A33.
- Implement USB bus and USB clocks via ccu_clk_gate table
for A23/A33, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for A23/A33, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A31.
- Implement USB ahb1 and USB clocks via ccu_clk_gate table
for A31, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB ahb1 and USB resets via ccu_reset table
for A31, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A10s/A13.
- Implement USB ahb and USB clocks via ccu_clk_gate table
for A10s/A13, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB resets via ccu_reset table for A10s/A13,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A10/A20.
- Implement USB ahb and USB clocks via ccu_clk_gate table
for A10/A20, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB resets via ccu_reset table for A10/A20,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner H3/H5.
- Implement USB bus and USB clocks via ccu_clk_gate table for
H3/H5, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table for
H3/H5, so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add common reset driver for all Allwinner SoC's.
Since CLK and RESET share common DT compatible, it is CLK driver
job is to bind the reset driver. So add CLK bind call on respective
SoC driver by passing ccu map descriptor so-that reset deassert,
deassert operations held based on ccu reset table defined from
CLK driver.
Select DM_RESET via CLK_SUNXI, this make hidden section of RESET
since CLK and RESET share common DT compatible and code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A64.
Implement USB clock enable and disable functions for
OHCI, EHCI, OTG and USBPHY gate and clock registers
via ccu clk gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Modify the RC and EP mode judge method, save the mode as a variable,
the variable will be used by other function.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Restore the legacy flow along with TFABOOT flow for
IFC configuration.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Each ECC layout consumes about 2984 bytes in the .data section. Allow
to disable the default ECC layouts if a driver is known to provide its
own ECC layout.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common
to support new numbe of pins and remove any platform dependency from
mscc-common.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Do not build write support, unless it's enabled.
In the SPL case, this change will typically remove
precious bytes (as write support is most often
not needed in SPL).
This is important on this platform, where the maximum
SPL size is 14 KiB.
With gcc v7.3, this change saves 144 bytes producing:
size spl/u-boot-spl
text data bss dec hex filename
9240 752 712 10704 29d0 spl/u-boot-spl
To make the code easier to compile-out and more
readable, a pair of read_data/write_data helpers are created.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use CONFIG_IS_ENABLED(BLK) instead of CONFIG_BLK,
in order to fix the following build issues when
CONFIG_SPL_MMC_WRITE is selected:
drivers/mmc/mmc_write.c:69:7: error: conflicting types for 'mmc_berase'
ulong mmc_berase(struct udevice *dev, lbaint_t start, lbaint_t blkcnt)
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:39:7: note: previous declaration of 'mmc_berase' was here
ulong mmc_berase(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt);
^~~~~~~~~~
drivers/mmc/mmc_write.c:187:7: error: conflicting types for 'mmc_bwrite'
ulong mmc_bwrite(struct udevice *dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:37:7: note: previous declaration of 'mmc_bwrite' was here
ulong mmc_bwrite(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
Switching private data manual allocation to driver model auto allocation
so users no longer need to deallocate themself because this would be
deallocated by driver model when the device is no longer required.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cache up to 4 kiB entries. 4 kiB is the default block size on ext4, yet
the underlying block layer devices usually report support for 512B . In
most cases, the 512B support is emulated (ie. SD cards, SSDs, USB sticks
etc.) and the real block size of those devices is much bigger.
To avoid performance degradation with such devices and FS setup, bump
the maximum cache entry size to 4 kiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
If _debug_uart_putc() is called before _debug_uart_init(), the
ns16550 debug uart driver hangs in a tight loop waiting for the
tx FIFO to get empty.
As this can happen via a printf sneaking in before the port calls
debug_uart_init(), introduce a config option to ignore characters
before the debug uart is initialized.
This is done by reading the baudrate divisor and aborting if is zero.
The Kconfig option is required as reading the baudrate divisor does
not seem to work for all ns16500 compatibles (which is why the last
attempt on this has been reverted in 1a67969a99).
Tested on socfpga_cyclone5_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DEBUG_UART_SKIP_INIT is used only by debug UART and thus should depend
on DEBUG_UART.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
Updates i2c muxes drivers to support livetree.
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is needed to properly calculate i2c bus speed divisors.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Xilinx AXI I2C controller driver based on the Linux i2c-xiic driver.
This driver is stripped of all the IRQ handling and uses pure polling,
yet tries to retain most of the structure of the Linux driver to make
backporting of fixes easy.
Note that the IP has a known limitation on 255 bytes read and write,
according to xilinx this is still being worked on [1].
[1] https://forums.xilinx.com/t5/Embedded-Processor-System-Design/AXI-IIC-V2-0-I2C-Master-Reading-multiple-bytes-from-I2C-slave/m-p/854419/highlight/true#M39387
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
At present this stores the error number in an unsigned int so an error is
never detected. Use the existing signed variable instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present the 'Index' column assumes there is only one digit. But on some
devices (e.g. snow) there are a lot of regulators and GPIO banks. Adjust
the output to allow for two digits without messing up the display.
Also capatalise the heading to match.
Fixes: 5197dafc42 (dm: core: Widen the dump tree to show more of the
driver's name.)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Liviu Dudau <liviu.dudau@foss.arm.com>
This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
The ethsys contains not only the clock gating controller, but also the
reset controller for the whole ethernet subsystem and its components.
This patch adds binding of the reset controller so that the ethernet node
can have references on it.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:
U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1
U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
This reverts commit a7f4b4b344.
As reported by Alex Kiernan the above optimization introduces a
regression in the below use case where:
1. Device has defined 'u-boot,dm-spl' property (@ eMMC DTS node)
2. The device downloads its MLO/SPL via UART (not eMMC - the eMMC pinmux
pins are NOT probed/configured in MLO/SPL).
3. The loaded via UART MLO/SPL wants to load Linux from eMMC. In this case
the DM core and pinctrl uclass checks 'u-boot,dm-spl' and don't
configure pins (as it thinks that those were initialized in MLO/SPL).
As we are very close to release - please revert this commit.
Reported-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes commit 0131162439 ("dm: usb: create a new UCLASS ID for USB gadget
devices")
The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.
Reported-by: Priit Laes <plaes@plaes.org>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Priit Laes <plaes@plaes.org>
Acked-by: Jagan Teki <jagan@openedev.com>
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)
To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).
If no alias is provided, then the index falls back to the order in which
the bindings took place.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Existing clock configure code has been followed based on the
legacy MMC dt node definitions and it cannot work with recent
dts(i) sync from Linux.
So, add clock configure code for Allwinner platforms which support
DM_MMC and eventually this will drop once CLK support is in Mainline.
Fixes: 3c92cca3cd ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet
Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
priv data has not been allocated when doing bind, so it is
wrong to use dev_get_priv in bind call back.
Let's switch to use platdata in the driver to fix the issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When boot_dev is true, fill boot device. However the original logic is when
boot_dev is false, fill boot device, this will trigger data abort.
Also fix sc_misc_get_control when using pointer val.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When build clk driver in spl, met the warning:
"
drivers/clk/imx/clk-imx8.c:21:25: warning: ‘imx8_clk_names’ defined but not used [-Wunused-variable]
static struct imx8_clks imx8_clk_names[] = {
^~~~~~~~~~~~~~
"
Fix with wrapping the array with CONFIG_CMD_CLK.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
After updating the value of dev_context_ptrs[0], we should flush this
from cache to memory. Otherwise the xhci controller won't use it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to keep SPL code size below the 32Kb limit,
put under CONFIG_SPL_BUILD flag all unused code in SPL.
This is needed for stm32f7xx board which are using SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case "gpio-ranges" property is not present in device tree,
use default value for gpio_count and gpio_range.
This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a"
command didn't return any pin status due to the fact that both stm32 F7
and H7 board DT doesn't use the gpio-ranges property.
Fixes: dbf928dd2634a6("gpio: stm32f7: Add gpio bank holes management")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit d0851c8937 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
Braces around the error-case for rk3399_pinctrl_set_pin_pupd lead to
an unconditional (and unintended) return from the function without it
ever setting pin-configurations.
Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcLfBzAAoJECaAFcEOcohNrMoH/ihFAiFblzVN7XPRTpV8+GGJ
gsljC7DRGkgMT7IOnmCE+/44RGaQnP3bHQH6WG4zVHZ6vhrEyzqPaYzbzLg90ujj
k1k4N6op3NA6e40FZvHzB/aglx1e5UFnWxstBpT1g82sL8xLSs0ubhsq6+gcr29I
0qGTILHxwY95qUGDi2zlYNEwv5B0enlucfhB5kTZ7QYZX+Jz1SL4AI0sIapTdMg+
/Bcu1Qi6B+xVklDhz9NUpYgst8T3J0Gabq7mqMXwommAgejsrjQWOnhDRrrWznd+
OsJqEEo/TmdT/eqO7SffooKiEUPrw6YmKPtZAXkdlc8Cm+qZRvr/okozALBJizY=
=v3QG
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190103' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for 2019.1:
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
This patch adds a Kconfig option to enable the full pinctrl driver
for the RK3399. This flag needs to be enabed in order to get the
features of the full pinctrl driver compiled in (i.e. a .set_state()
callback).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The current pinctrl driver for the RK3399 has a range of qulity issues.
E.g. it only implements the .set_state_simple() callback, it
does not parse the available pinctrl information from the DTS
(instead uses hardcoded values), is not flexible enough to cover
devices without 'interrupt' field in the DTS (e.g. PWM),
is not written generic enough to make code reusable among other
rockchip SoCs...
This patch addresses these issues by reimplementing the whole driver
from scratch using the .set_state() callback.
The new implementation covers all featurese of the old code
(i.e. it supports pinmuxing and pullup/pulldown configuration).
This patch has been tested on a RK3399-Q7 SoM (Puma).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch allows to enable the PWM regulator driver
independent for U-Boot and SPL.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip may use this sdram copy of source code for both open source
and internal project, update the license to use both GPL2.0+ and
BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds Hynix H27UBG8T2BTR id table as part of raw nand,
these chips were available in some A20-olinuxino-micro boards.
Signed-off-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
[jagan: add proper commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Current driver doesn't check if the destination pointer is NULL.
This cause the data from the FIFO to be stored inside the internal
SDRAM ( address 0 ).
The patch add simple check if the destination pointer is NULL.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: fix commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This commit adds support for device tree and enumeration via device model
for the Vybrid's NFC NAND driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit provides code to add proper entry to Kconfig to enable
support for VF610 device tree aware driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Without this change it is possible that Vybrid's NFC driver malloc() call
will obtain some memory used (and correctly free'd) by some previous
driver (in this case pinctrl for Vybrid).
As a result some fields of struct nfc - in out case mtd->_get_device - are
"pre initialized" with some random values.
On the latter stage of booting, when e.g. somebody calls 'mtdparts default'
the "data abort" is observed when __get_mtd_device() function is called.
The mtd->_get_device pointer is not NULL and wrong value is referenced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.MX50, i.MX53
Only tested on i.MX53 hardware but in both modes
(by modifying the device tree).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
The Denali NAND controller IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
Currently, only the first one (50MHz) is provided. The rest of the
two clock ports must be connected to the 200MHz clock line. Add this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit cf51e4b9c34407bf0c3d9b582b7837e047e1df47
Add the register read-back, commenting why this is necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit 1dfac31a5a63ac04a9b5fbc3f5105a586560f191
This commit improves the ->setup_data_interface() hook.
The denali_setup_data_interface() needs the frequency of clk_x
and the ratio of clk_x / clk.
The latter is currently hardcoded in the driver, like this:
#define DENALI_CLK_X_MULT 6
The IP datasheet requires that clk_x / clk be 4, 5, or 6. I just
chose 6 because it is the most defensive value, but it is not optimal.
By getting the clock rate of both "clk" and "clk_x", the driver can
compute the timing values more precisely.
To not break the existing platforms, the fallback value, 50 MHz is
provided. It is true for all upstreamed platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit 6f1fe97bec349a1fd6c5a8c7c5998d759fe721d5
Currently, denali_dt.c requires a single anonymous clock, but
the Denali User's Guide requires three clocks for this IP:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
This commit supports these named clocks to represent the real hardware.
For the backward compatibility, the driver still accepts a single clock
just as before. The clk_x_rate is taken from the clock driver again if
the named clock "clk_x" is available. This will happen only for future
DT, hence the existing DT files are not affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present it is possible to enable TrueType support but not include any
fonts. This results in a blank display. Select Nimbus as the default font
to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
commit 4f86a724e8 ("power: regulator: denied disable on always-on
regulator") throws an error when requested to disable an always-on
regulator. It is right that an always-on regulator should not be
attempted to be disabled. But at the same time regulator framework
should not return an error when such request is received. Instead
it should just return success without attempting to disable the
specified regulator. This is because the requesting driver will
not have the idea if the regulator is always-on or not. The
requesting driver will always try to enable/disable regulator as
per the required flow. So it is upto regulator framework to not
break such scenarios.
Fixes: 4f86a724e8 ("power: regulator: denied disable on always-on regulator")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When fixed-link phy is used subnode offset is used as phy address. This
number is bigger then space allocated for bus structure (allocated via
mdio_alloc).
bus->phymap[] array has PHY_MAX_ADDR size (32).
That's why writing bus->phymap[addr] where addr is < 0 or > PHY_MAX_ADDR
is causing write to memory which can caused full U-Boot crash.
The patch is checking if address is in correct range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit prevents from re-configuring pins if those were configured
before relocation.
Some pins - like UART or DDR must be setup before relocation
(as they have 'u-boot,dm-pre-reloc' property set in DTS). Without this
change, those pins are re-configured after relocation (pre_reloc_only = 0,
so we do not "continue").
Such behavior may be a problem for DDR PAD configuration, as they might
be already leveled/tuned with original setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Add driver for the JZ47xx MSC controller.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add driver for the efuse block in the JZ47xx SOC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.
Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.
Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This driver supports the pin and gpio controller found in the Ocelot and
Luton SoCs.
The driver was inspired from the pinctrl driver in Linux, but was
simplified and was modified to allow supporting an other SoCs (Luton).
For Ocelot and Luton the controller is the same, only the pins to program
differ.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[changed to only descend into mscc/ dependent on CONFIG_PINCTRL_MSCC]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
On some platforms, as the Ocelot ones, when wanting to control the CS
through software, it is not possible to do it through the GPIO
controller. Indeed, this signal is managed through a dedicated range of
registers inside the SoC..
By declaring the external_cs_manage function as weak, it is possible to
manage the CS at platform level and then using the appropriate registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds SiFive UART driver. The driver is 100% DM driver
and it determines input clock using clk framework.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
RISC-V privileged architecture v1.10 defines a real-time counter,
exposed as a memory-mapped machine-mode register - mtime. mtime must
run at constant frequency, and the platform must provide a mechanism
for determining the timebase of mtime. The mtime register has a
64-bit precision on all RV32, RV64, and RV128 systems.
Different platform may have different implementation of the mtime
block hence an API riscv_get_time() is required by this driver for
platform codes to hide such implementation details. For example,
on some platforms mtime is provided by the CLINT module, while on
some other platforms a simple 'rdtime' can be used to get the timer
counter.
With this timer driver the U-Boot timer functionalities like delay
works correctly now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This adds a driver for RISC-V CPU. Note the driver will bind
a RISC-V timer driver if "timebase-frequency" property is
present in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
+ Update the function syscon_node_to_regmap() to force bound on
syscon uclass and directly use the list of device from DM.
+ Remove the static list syscon_list.
This patch avoid issue (crash) when syscon_node_to_regmap() is called
before and after reallocation (list content is invalid).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In some cases, UART is configured by early boot stage.
To be sure of the initial state of UART and to avoid
spurious chars on console, reset the serial block before
configuring it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If OP-TEE core is compiled with support of REE FS and RPMB
at the same time (CFG_RPMB_FS ?= y; CFG_RPMB_FS ?= y), and persistent
storage API is used with TEE_STORAGE_PRIVATE storage id, it will
lead to TA panic.
E/TC:? 0 TA panicked with code 0xffff0009
.....
E/TC:? 0 Call stack:
E/TC:? 0 0x000000004002f2f8 TEE_OpenPersistentObject at
lib/libutee/tee_api_objects.c:422
In this particular case TEE_ERROR_STORAGE_NOT_AVAILABLE is more suitable
than TEE_ERROR_NOT_IMPLEMENTED, as it provides to a TA a possibility
to handle this error code [1].
>From GPD TEE Internal Core specification [2]:
TEE_ERROR_STORAGE_NOT_AVAILABLE - if the persistent object is stored in a
storage area which is currently inaccessible. It may be associated with
the device but unplugged, busy, or inaccessible for some other reason.
[1]: 94db01ef44/lib/libutee/tee_api_objects.c (L419)
[2]: https://globalplatform.org/wp-content/uploads/2018/06/GPD_TEE_Internal_Core_API_Specification_v1.1.2.50_PublicReview.pdf
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
When the device is in peripheral mode there is no
struct usb_bus_priv allocated pointer, as the uclass driver
("usb_dev_generic") doesn't call per_device_auto_alloc_size.
This results in writing to the internal SDRAM at
priv->desc_before_addr = true;
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
For USB3.0, the max packetsize for GET_DESCRIPTOR should be
sent as exponent value for 2. This means for 512, max packet
size should be filled with 9(2^9=512). Also, fill the USB
version field with 3.0 if speed is negotiated to Superspeed.
This fixes the issue of DFU gadget download failure with
superspeed. Without this patch, the max packet size is
overflowed to zero as the bMaxPacketsize is of u8 and hence
host is not able to detect this device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The set_phy_power() callback is part of struct omap_musb_board_data. This
structure is part of the platform data passed to the musb-new driver. This
does not really fit with the Driver Model, so allow not to use struct
omap_musb_board_data to turn the phy on or off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some drivers might need to access common USB functions such as
usb_get_maximum_speed() or usb_get_dr_mode().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There don't appear to be any boards enabling CONFIG_USB_DA8XX,
and there is a newer version of the MUSB driver, so let's remove
the legacy version of it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch removes CONFIG_USB_DAVINCI. It's a legacy option
that isn't defined anywhere, and there is a newer MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When CONFIG_SPL_DM_USB was added, it was added defaulted on without
protection to ensure it didn't get set for non-DM SPL builds.
This leads to unexpected and confusing failures when building a DM based
U-Boot but with a non-DM SPL, as the defconfig is unlikely to have
CONFIG_SPL_DM_USB actively disabled.
Tweak the Kconfig to not enable this setting unless CONFIG_SPL_DM is set.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.
This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Currently it's not possible to get filesize of downloaded images and
it's impossible to automate some tasks in scripts. So this patch adds
`filesize` environment variable with size (as hex number in bytes) of
the last successfully downloaded file via `sdp` command.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
At present the 'beep' sound generates a waveform for only one channel even
if two are being used. This means that the beep is twice the frequency it
should be. Correct this by making it a parameter.
The fix in a previous commit was correct for sandbox but not for other
boards.
Fixes: 03f11e87a8 ("sound: Correct data output in sound_create_square_wave()")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these parameters are hard-coded in the sdl interface code.
Allow them to be specified by the driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current ID enums start from 1 but there does not seem to be any reason
that they cannot start with 0. Adjust the code to avoid the +1 in
codec_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
This structure contains information that is likely needed by any i2s
driver so it seems useful to attach it to the (forthcoming) i2c uclass.
For now, just rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot sound system provides basic support for beeping. At present it
does not use driver model, but it needs to be converted. Add an option to
enable driver model for sound. For now it is not connected to anything.
Future work will add drivers which use this option. It will then be
removed once everything is converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are only used in two functions so can be made local.
Also change the first argument of max98095_do_init() to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we cannot pass in the global struct, but instead want
to pass in the driver-private data. Split some of the code out of
wm8994_init() to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename max98095_update_bits() to max98095_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename wm8994_update_bits() to wm8994_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
This struct is only used by the Samsung I2C driver and should move into
that driver. For now, rename it so it is clear that is driver-private
info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f32a8007ef ("dm: i2c: Make i2c_get_chip_for_busnum() fail if the
chip is not detected") introduced a regression for the NVIDIA Jetson TX2.
For some reason the xfer callback of the tegra i2c driver doesn't support
probing the I2C devices with a 0-length message.
Fixing the regression by providing a dummy implementation of probe_chip()
that does nothing.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
This implements a driver using a RTC-based backing store for the DM
bootcount implementation. The node configuring this feature will be
compatible with 'u-boot,bootcount-rtc' and the underlying RTC device
shall be reference through the property 'rtc'. An offset into the RTC
device's register space can be provided through the 'offset' property.
Tested on a RK3399-Q7 on a Flamingo carrier board using the SRAM area
of the carrier board's RV3029 RTC.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured through defines statically). On a modern system
that exposes multiple devices in a DTS-configurable way, this is less
than optimal and a interface to DM-based devices will be desirable.
This adds a simple driver that is DM-aware and configurable via DTS.
If ambiguous (i.e. multiple bootcount-devices are present) the
/chosen/u-boot,bootcount-device property can be used to select one
bootcount device.
Initially, this provides support for the following DM devices:
* RTC devices
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Patch for rk322x TPL is not merged, and only SPL is available now,
enable the sdram driver in SPL first. We should update back to TPL
after TPL is enabled for rk322x.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To reset the DM after a new dtb is loaded, we need to call dm_uninit()
and then dm_init(). This fails however because gd->dm_root is not nullified
by dm_uninit().
Fixing it by setting gd->dm_root in dm_uninit().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is currently not possible to include the support to remove devices in
the SPL. This is however needed by platforms that re-select their dtb after
DM is initialized; they need to remove all the previously bound devices
before triggering a scan of the new DT.
Add a Kconfig option to be able to include the support for device removal
in the SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Seeries-changes:3
- update commit message
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those driver are not DM drivers per se (not using the PMIC/regulator
framework) and are using the legacy I2C API. Make them compatible with
the DM_I2C API.
This impacts the following drivers:
- palmas (used by am57xx/dra7xx evms)
- tps65218 (used by am43xx evms)
- tps65217 and tps65910 (used by am335x evms and am335x boneblack vboot)
- twl4030 (used by omap3_logicpd)
- tps65217 (used by brppt1)
- twl6030
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If OF_CONTROL is not enabled and DM_SEQ_ALIAS is enabled, we must
assign an alias (requested sequence number) to devices that belongs to a
class with the DM_UC_FLAG_SEQ_ALIAS flag. Otherwise
uclass_find_device_by_seq() cannot be used to get/probe a device. In
particular i2c_get_chip_for_busnum() cannot be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
i2c_get_chip_for_busnum() really should check the presence of the chip on
the bus. Most of the users of this function assume that this is done.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This syncs drivers/ddr/marvell/a38x/ with the mv_ddr-armada-18.09 branch
of https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
Specifically this syncs with commit 99d772547314 ("Bump mv_ddr to
release armada-18.09.2").
The complete log of changes is best obtained from the mv-ddr-marvell.git
repository but some relevant highlights are:
ddr3: add missing txsdll parameter
ddr3: fix tfaw timimg parameter
ddr3: fix trrd timimg parameter
merge ddr3 topology header file with mv_ddr_topology one
mv_ddr: a38x: fix zero memory size scrubbing issue
The upstream code is incorporated omitting the portions not relevant to
Armada-38x and DDR3. After that a semi-automated step is used to drop
unused features with unifdef
find drivers/ddr/marvell/a38x/ -name '*.[ch]' | \
xargs unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 \
-UCONFIG_APN806 -UCONFIG_MC_STATIC \
-UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_64BIT -UCONFIG_A3700 -UA3900 -UA80X0 \
-UA70X0
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dvG1
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20181207' of git://git.denx.de/u-boot-amlogic
Two fixes for the Amlogic Pinctrl driver :
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
Some boards feature a capacitance on LDO3's output that is too large,
causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.
A fix appeared to be done with
commit 0e6e34ac8d ("sunxi: Olimex A20 boards: Enable LDO3 and LDO4 regulators").
The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system freezes.
While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.
To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 LDO3 regulator supports voltage rate control, or can set a
slew rate.
This allows for the power to gradually rise up to the desired voltage,
instead of spiking up as fast as possible. Reason to have this can be
to reduce the inrush currents for example.
There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.
In ideal world (where vendors follow the recommended design guidelines)
this setting should not be enabled by default. Unless of course AXP209
crashes instead of reporting overcurrent condition as it normally should
do in this case.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 has a few 'magisc-ish' values that are better served with
clear defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use a define for the chip version mask on the axp209.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
syscon_regmap_lookup_by_phandle() can be used to get the regmap of a syscon
device from a reference in the DTS. It operates similarly to the linux
version of the namesake function.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.
usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch adds code missing when CONFIG_DEBUG_UART_OMAP is enabled as
early debugging UART. The code is basically copied from the ns16550
driver.
Signed-off-by: Felix Brack <fb@ltec.ch>
Due to gpio holes management, stm32_pinctrl_get_gpio_dev() must
be updated.
stm32_pinctrl_get_gpio_dev() returns from a given pin selectors
the corresponding bank gpio device and the gpio_offset inside this
gpio bank.
Update also all functions which makes usage of stm32_pinctrl_get_gpio_dev.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move gpio_dev list filling outside probe() to speed-up U-boot
boot sequence execution. This list is populated only when needed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds channels support for dma controllers that have multiple channels
which can transfer data to/from different devices (enet, usb...).
DMA channle API:
dma_get_by_index()
dma_get_by_name()
dma_request()
dma_free()
dma_enable()
dma_disable()
dma_prepare_rcv_buf()
dma_receive()
dma_send()
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[grygorii.strashko@ti.com: drop unused dma_get_by_index_platdata(),
add metadata to send/receive ops, add dma_prepare_rcv_buf(),
minor clean up]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move dma_ops to a separate header file, following other uclass
implementations. While doing so, this patch also improves dma_ops
documentation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The pin number (first and last) in the bank definition is missing the
pin base offset shifting. This is causing a miscalculation when
retrieving the register and pin offsets in the GPIO driver causing the
'gpio' command to drive the wrong pins / GPIOs in the second GPIO chip
(the AO bank is driven correctly because the shifting is already 0).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Protect configuration registers with a hardware spinlock.
If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add hardware spinlock in the list of the clocks.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In commit e5e06b65ad ("clk: Allow clock defaults to be set also
during re-reloc state") the earlier guard against setting clock
defaults in pre-reloc state was removed. While it is easy to filter
'assigned-clocks' properties for SPL using CONFIG_OF_SPL_REMOVE_PROPS,
no such mechanism exists for the pre-reloc stage of the full U-Boot.
With the default defconfig for the RK3399-Q7 (which filter the
'assigned-clocks' property for the DTS used by SPL anyway), this
caused a pause during startup of the full U-Boot stage that lasted for
almost 10s (due to the CPU not having been clocked up yet).
This reintroduces the guard from commit f4fcba5c5b ("clk: Allow
clock defaults to be set also during re-reloc state") and extends it
to only apply outside of a TPL/SPL build: i.e. clk_set_defaults will
now run in pre-reloc state for SPL, but only after reloc for the full
U-Boot.
References: commit f4fcba5c5b ("clk: implement clk_set_defaults()")
References: commit e5e06b65ad ("clk: Allow clock defaults to be set
also during re-reloc state")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add ahci compatible support for ls2080a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
[YS: add fallthrough comment]
Reviewed-by: York Sun <york.sun@nxp.com>
Add ahci compatible support for ls1088a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support and allows to pick QE firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove line continuation in quoted string]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support and allows to pick FMAN firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
IFC driver changes to implement the chipselect mappings at run time.
Defines init_early_memctl_regs and init_final_memctl_regs with
chipselect dynamic mapping for nor and nand boot.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Sometimes enumeration fails (about 1 in 50 times on my custom board).
The underlying reason is probably electrical but Linux does not have
the problem.
Comparing the Linux / u-boot implementations shows that Linux
retries the error case whereas u-boot aborts early.
Removing the early abort in u-boot fixes the problem.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
SPI flash based MTD devs can be registered/unregistered at any time
through the sf probe command or the spi_flash_free() function.
This commit does not try to fix the root cause as it would probably
require rewriting most of the code and have an mtd_info object
instance per spi_flash object (not to mention that the the spi-flash
layer is likely to be replaced by a spi-nor layer ported from Linux).
Instead, we try to be as safe as can be by checking the code returned
by del_mtd_device() and complain loudly when there's nothing we can
do about the deregistration failure. When that happens we also reset
sf_mtd_info.priv to NULL, and check for NULL pointer in the mtd hooks
so that -ENODEV is returned instead of hitting a NULL pointer
dereference exception when the MTD instance is later accessed by a user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The DM implementation of spi_flash_free() does not unregister the MTD
device before removing the spi dev object. This leads to a use-after-free
bug when the MTD device is later accessed by a MTD user (observed when
attaching the device to UBI after env_sf_load() has called
spi_flash_free()).
Implement ->remove() and call spi_flash_mtd_unregister() from there.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MTD partition creation code is a bit tricky. It tries to figure out
when things have changed (either MTD dev list or mtdparts/mtdids vars)
and when that happens it first deletes all the partitions that had been
previously created and then creates the new ones based on the new
mtdparts/mtdids values.
But before deleting the old partitions, it ensures that none of the
currently registered parts are being used and bails out when that's
not the case. So, we end up in a situation where, if at least one MTD
dev has one of its partitions used by someone (UBI for instance), the
partitions update logic no longer works for other devs.
Rework the code to relax the logic and allow updates of MTD parts on
devices that are not being used (we still refuse to updates parts on
devices who have at least one of their partitions used by someone).
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The mtdparts variable might contain partition definitions for several
MTD devices. Each partition layout is separated by a ';', so let's
make sure we don't pick a wrong name when mtdparts is malformed.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The local mtd_name[] variable is limited in size. Return an error if
the name passed in mtdparts does not fit in this local var.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
strstr() does not guarantee that the string we're searching for is
placed at the beginning. Use strncmp() instead.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The environment is not guaranteed to contain a valid mtdids variable
when called from mtd_search_alternate_name(). Call get_mtdids() instead
of env_get("mtdids").
Fixes: ff4afa8a98 ("mtd: uboot: search for an equivalent MTD name with the mtdids")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
spi_flash_mtd_register() can be called several times and each time it
will register the same mtd_info instance like if it was a new one.
The MTD ID allocation gets crazy when that happens, so let's track the
status of the sf_mtd_info object to avoid that.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If we don't do that, partitions might still be exposed while the
underlying device is gone.
Fixes: 2a74930da5 ("mtd: mtdpart: implement proper partition handling")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Updates to the MTD device list should trigger a new parsing of the
mtdids/mtdparts vars even if those vars haven't changed.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
We need to parse mtdparts/mtids again everytime a device has been
added/removed from the MTD list, but there's currently no way to know
when such an update has been done.
Add an ->updated field to the idr struct that we set to true every time
a device is added/removed and expose a function returning the value
of this field and resetting it to false.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
New callback will supply necessary information, for example,
to ACPI SPCR table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cache the value of the reg-io-width property for the future use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
New callback will give a necessary information to fill up ACPI SPCR table,
for example. Maybe used later for other purposes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change ADR_SPACE_SYSTEM_IO to SERIAL_ADDRESS_SPACE_IO to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
