Commit graph

55792 commits

Author SHA1 Message Date
Stefan Roese
7bf9bca7c0 net: macb: Add small delay after link establishment
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.

Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-09 09:28:50 +03:00
Claudiu Beznea
068d4c0a11 pinctrl: at91: add slewrate support for SAM9X60
Add slew rate support for SAM9X60 pin controller.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2019-04-09 09:28:50 +03:00
Claudiu Beznea
be6e24054d pinctrl: at91: add compatibles for SAM9X60 pin controller
Add compatibles for SAM9X60 pin controller.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2019-04-09 09:28:50 +03:00
Claudiu Beznea
1a6a82882e pinctrl: at91: add drive strength support for SAM9X60
Add drive strength support for SAM9X60 pin controller.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2019-04-09 09:28:50 +03:00
Claudiu Beznea
04d4ec9c57 pinctrl: at91: add option to use drive strength bits
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2019-04-09 09:28:50 +03:00
Stefan Roese
a71e2f933b arm: at91: Add gardena-gateway-at91sam support
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
d4c8873f93 arm: at91: at91sam9x5.dtsi: Add watchdog handle
This makes it possible to reference the watchdog DT node via "&watchdog"
from board dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
fc89afba11 arm: at91: siemens: Add support to generate combined SPL+U-Boot image
This patch adds the necessary defines to the Siemens AT91SAM based
boards (smartweb, corvus and taurus) to generate the combined binary
image with SPL and main U-Boot image combined (u-boot-with-spl.bin).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
9ea6f718eb Makefile: Add Kconfig option CONFIG_SPL_IMAGE to select the SPL binary
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that
shall be used to generate the combined SPL + U-Boot image. The default
value is the current value "spl/u-boot-spl.bin".

This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets
which use SPL NAND support (boot from NAND). For these build targets the
combined image "u-boot-with-spl.bin" is now automatically generated and
can be programmed into NAND as one single image (vs. SPL image and U-Boot
as 2 separate images).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09 09:28:50 +03:00
Stefan Roese
581e711ad1 Makefile.spl: Move generated AT91SAM NAND image boot.bin to spl directory
This patch moves the AT91SAM NAND booting SPL image "boot.bin" which
includes the ECC values from the root directory into the spl directory,
where all SPL related images are located.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
da8a771241 arm: at91: arm926ejs/u-boot-spl.lds: Add _image_binary_end to SPL lds
This patch adds _image_binary_end to the SPL linker script. This will be
used be the upcoming GARDENA AT91SAM based platform, which uses DT in
SPL and configures CONFIGURE_SPL_SEPARATE_BSS.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
256c2ff0cc arm: at91: Enable watchdog support
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09 09:28:50 +03:00
Stefan Roese
05d4b8e4ad arm: at91: Remove CONFIG_AT91_HW_WDT_TIMEOUT
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09 09:28:50 +03:00
Stefan Roese
6c04bd3857 watchdog: at91sam9_wdt: Fix WDT setup in at91_wdt_start()
This patch fixes the timer register setup in at91_wdt_start() to
correctly configure the register again. The input timeout value is
now in milli-seconds instead of seconds with the new watchdog API.
Make sure to take this into account and only use a max timeout
value of 16 seconds as appropriate for this SoC.

Also the check against a lower timeout value than 0 is removed. This
check makes no sense, as the timeout value is unsigned.

Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
7fbd42f5af watchdog: Handle SPL build with watchdog disabled
This patch adds some checks, so that the watchdog can be enabled in main
U-Boot proper but can be disabled in SPL.

This will be used by some AT91SAM based boards, which might enable the
watchdog in the main U-Boot proper and not in SPL. It will be enabled in
SPL by default there, so no need to configure it there. This approach
saves some space in SPL.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
e567dfb213 serial: atmel_usart: Use fixed clock value in SPL version with DM_SERIAL
This patch adds an alterative SPL version of atmel_serial_enable_clk().
This enables the usage of this driver without full clock support (in
drivers and DT nodes). This saves some space in the SPL image.

Please note that this fixed clock support is only added to the SPL code
in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL
should not be affected.

This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART
input clock. It defaults to 132096000 for ARCH_AT91 but can be set to
a different value if needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09 09:28:50 +03:00
Stefan Roese
ce4d04af99 arm: at91: spl_at91.c: Call spl_early_init() if OF_CONTROL is enabled
This patch adds a call to spl_early_init() to board_init_f() which is
needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for
the early SPL setup including the DTB setup for later usage.

Please note that this call might also be needed for non SPL_OF_CONTROL
board, like the smartweb target. But smartweb fails to build with this
call because its binary grows too big. So I disabled it for these kind
of targets for now.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Stefan Roese
e6a2769360 arm: at91: Makefile: Compile lowlevel_init only when really necessary
Make sure that lowlevel_init is not compiled when
CONFIG_SKIP_LOWLEVEL_INIT_ONLY is configured.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09 09:28:50 +03:00
Ilko Iliev
d9bd42900c board: pm9g45: Migrate to CONFIG_DM
Migrate the following options to CONFIG_DM:
  CONFIG_DM_GPIO
  CONFIG_DM_MMC
  CONFIG_DM_ETH
  CONFIG_DM_SERIAL
  CONFIG_DM_USB

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2019-04-09 09:28:50 +03:00
Alexander Dahl
7dee1848d7 ARM: at91: sama5d2: Wrap cpu detection to fix macb driver
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional
chip id. The check if the cpu is sama5d2 was changed from a preprocessor
definition (inlining a call to 'get_chip_id()') to a C function,
probably to not call get_chip_id twice?

That however broke a check in the macb ethernet driver. That driver is
more generic and also used for other platforms. I suppose this solution
was implemented to use it in 'gem_is_gigabit_capable()', without having
to stricly depend on the at91 platform:

	#ifndef cpu_is_sama5d2
	#define cpu_is_sama5d2() 0
	#endif

That only works as long as cpu_is_sama5d2 is a preprocessor definition.
(The same is still true for sama5d4 by the way.) So this is a straight
forward fix for the workaround.

The not working check on the SAMA5D2 CPU lead to an issue on a custom
board with a LAN8720A ethernet phy connected to the SoC:

	=> dhcp
	ethernet@f8008000: PHY present at 1
	ethernet@f8008000: Starting autonegotiation...
	ethernet@f8008000: Autonegotiation complete
	ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff)
	BOOTP broadcast 1
	BOOTP broadcast 2
	BOOTP broadcast 3
	BOOTP broadcast 4
	BOOTP broadcast 5
	BOOTP broadcast 6
	BOOTP broadcast 7
	BOOTP broadcast 8
	BOOTP broadcast 9
	BOOTP broadcast 10
	BOOTP broadcast 11
	BOOTP broadcast 12
	BOOTP broadcast 13
	BOOTP broadcast 14
	BOOTP broadcast 15
	BOOTP broadcast 16
	BOOTP broadcast 17

	Retry time exceeded; starting again

Notice the wrong reported link speed, although both SoC and phy only
support 100 MBit/s!

The real issue on reliably detecting the features of that cadence
ethernet mac IP block, is probably more complicated, though.

Fixes: 245cbc583d ("ARM: at91: Get the Chip ID of SAMA5D2 SiP")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
2019-04-09 09:28:50 +03:00
Tom Rini
3c99166441 Prepare v2019.04
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-08 21:40:40 -04:00
Jagan Teki
85c3d46322 arm: sunxi: Enable DM_MMC on required SoCs
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.

Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]

So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.

Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.

[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html

Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-08 16:35:15 -04:00
Tom Rini
c48b07a9fd - i.MX8QXP-MEK ethernet fix
-----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXKtM/A4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXIuwAJwPGkXMY2V1JWjtWrxV3Ctey8rkvACeML/qP1Ee
 m/WnldHMc++lLZRMVvw=
 =aYD0
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-staging

- i.MX8QXP-MEK ethernet fix
2019-04-08 10:11:29 -04:00
Andrejs Cainikovs
e82fa10b3e dts: imx8qxp-mek: Add PHY post reset delay
PHY cannot be detected unless we wait about 150 ms.

Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-08 15:24:39 +02:00
Andrejs Cainikovs
31d4045d4b net: dm: fec: Support phy-reset-post-delay property
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
  a delay of phy-reset-post-delay milliseconds will be observed after the
  phy-reset-gpios has been toggled. Can be omitted thus no delay is
  observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.

Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-04-08 15:23:28 +02:00
Stefan Roese
ccd063e981 watchdog: Move watchdog_dev to data section (BSS may not be cleared)
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2019-04-08 09:21:39 -04:00
Hannes Schmelzer
afbc31948a net: phy: implement fallback mechanism for negative phy adresses
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
2019-04-07 20:31:16 -04:00
Tom Rini
0e62d5b2ab Fixes for 2019.04
- fix bashism for MX8
 	- fix ethernet for MX53
 	- fix docs for i.MX8
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlynLM8PHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et38/QL/Rc3p1pF6Dr9zKzxA0rcMoBo9MzzTrUP6XrN
 8syDBJNo2u93Msv78xHTQMCcfxRR3bkTYiWPEzWphC4Qk2IZIe2sETxu2BqsmWRI
 qzK5+L7oU3qJYqY8mZTUKPhmNxDu7E6yGXI1cWboWSR+/DMTxrUHZU5gjQyaQ/WN
 Diko1+lyaygZyPv0FzBdx7Vv+agQusGXGu4XbRkOXhrE6ytMv2ZjCzUtMYRIUg8H
 057DtJfwgU+zfimUoeuiltAwywh9UGxmlR4kb6rF5VZWX0Xn/XoVbMR6qRQXaFIz
 PzlNu3FEpOmvBQ5W5xySHS0CzbeTisIopJehZbkCc+XaEr80GplN995rGWGIN5av
 nlYS7rWHyIcVxoQNT61JTfVC1blFu6+tiokINWFI8as0fMrEAU4okzT4oBaGxdun
 CVcZDo9ytxKWLqtpD0MIQW4r4kJ27yWe3s4ot+v/+jb+XwkatX2J6oaiKviFFhuc
 BwniIb9lsi3ESIOaQXjpJ+qAw9gWYA==
 =//jr
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190405' of git://git.denx.de/u-boot-imx

Fixes for 2019.04

	- fix bashism for MX8
	- fix ethernet for MX53
	- fix docs for i.MX8
2019-04-05 09:09:56 -04:00
Tom Rini
0e708abcbb Merge branch 'master' of git://git.denx.de/u-boot-usb
- Documentation fix
2019-04-03 10:28:10 -04:00
Tom Rini
05fa129a40 Merge branch '2019-04-03-master-imports'
- Important Khadas VIM2 fix
- Build fix for macOS Mojave
- Build fix for gcc-4.7 for host tools.
2019-04-03 10:26:57 -04:00
Thomas Petazzoni
d7edeba79b tools/Makefile: build host tools with -std=gnu99
Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.

It fixes the following build failure:

./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
  for (int i = 0;  i < len;  i++)
  ^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code

when building the host tools with gcc 4.7.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-04-03 10:26:46 -04:00
默默
ab8fc41302 fix compile error on macOS Mojave 2019-04-03 10:26:46 -04:00
Neil Armstrong
2118a272e3 configs: khadas_vim2: Fix defconfig
The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-03 10:23:45 -04:00
Neil Armstrong
82548aaad5 phy: Also allow MESON_GXM for MESON_GXL_USB_PHY
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.

Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-03 10:23:38 -04:00
Eugen Hristev
7252274978 travis-ci: fix at91 missing boards
Fix missing at91 boards and split the at91 in two categories:
at91 arm v7
at91 arm926esj
which are the two main cores for the at91 architecture.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-02 09:05:03 -04:00
Lukasz Majewski
da60b4301c DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106

The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02 13:44:18 +02:00
Lukasz Majewski
8e2b1f2251 cosmetic: Remove not needed string from kp_imx53.h config
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02 13:44:18 +02:00
Lukasz Majewski
f73c09e735 cosmetic: config: Remove empty #ifdefs
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.

Remove them to clean u-boot source code.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02 13:44:18 +02:00
Krzysztof Kozlowski
2a766db11a doc: Fix outdated ohci board hook documentation
The ohci driver calls board_usb_init(), not usb_board_init().

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2019-04-02 12:52:54 +02:00
Fabio Estevam
6574931732 imx8mq_evk: README: Make the underline marker fill the whole sentence
Let the underline marker "=" fill the whole sentence for better
readability.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02 10:36:35 +02:00
Fabio Estevam
d3c8727bcf imx8mq_evk: README: Fix a typo in the destination path
The DDR firmware binaries should be copied to '$(srctree)', so fix
a typo.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02 10:36:35 +02:00
Fabio Estevam
0adc3f8538 imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.

Make this step explicit in the instructions.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02 10:36:35 +02:00
Tom Rini
da06f9a185 Merge branch 'master' of git://git.denx.de/u-boot-sh
Minor fixes for the Alt board and PHY use on Gen2.
2019-04-01 23:30:00 -04:00
Tom Rini
bcd40c347d Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- clk: sunxi: a10: Add CLK_AHB_GMAC
2019-04-01 12:31:22 -04:00
Jagan Teki
9d1e136734 clk: sunxi: a10: Add CLK_AHB_GMAC
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-01 21:45:15 +05:30
Baruch Siach
8a0746dba0 tools/imx8m_image.sh: remove bashism
Use a single '=' to test string equality for compatibility with non-bash
shells. Otherwise, if /bin/sh is dash, build fails:

./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
2019-04-01 17:52:37 +02:00
Tom Rini
4da84d1b9b Fixes for 2019.01
- pico-imx6ul: fix after conversion
 	- engicam boards
 	- pico-imx7d _ README due to hang with imx-usb-loader
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlyhyjAPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3LD4MAMCkfd9IyPhy+TWXCatCmoLhD5+0MmhvxU4z
 gHrmO0n/rHL3mqJ0ya4RgmN/mTPa+0nFZ2yarTxD8Yhm9T9R/IIhLC7MxvNeojbC
 oXjMNE4P9TMgvUTEzqbdAp+B9Cy7TdygnCVmUPJuleAvePCxX4kM/UTMiNveUKLo
 xgYqfRxpSR1gef7me+HJEoVA0Bc4VgbbASN04Zw8FyFSXaJz4VUAcxFXZKHiYa8j
 OSjIk8rItHOgmZkTH12QWhqp9wJcD8AJgVNsCgdGxxTJSleAjoojjO9nGeGSHLzJ
 fGiGDlMvh63G8GypjfHAAfTXRLv5GJSkxLIYBolRmao+ELYLEkaU6Y33WX0td50U
 ufjuQCaO/g8UiRRwpqT1138GEkzwKAm9fN0T7c8yDi2CeW2ihugJJySuSgoJg1Nj
 qgf3u4EpgSKdAiUxM5gr58x+cugGUVZ62y0QELrbq5xoJHriMwWzilxHGhAASmfO
 r4YCtfpH4PZXe9nmrh31qHRjcXPxVw==
 =TWtH
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190401' of git://git.denx.de/u-boot-imx

Fixes for 2019.01

	- pico-imx6ul: fix after conversion
	- engicam boards
	- pico-imx7d _ README due to hang with imx-usb-loader
2019-04-01 09:39:38 -04:00
Fabio Estevam
00102ae520 pico-imx7d: README: Recommend the usage of a USB hub
Since commit 9e3c0174da ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.

There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.

Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.

The solution for that is to use an externally powered USB hub between the
board and the host computer.

Add such recommendation to the README file.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-03-31 20:19:19 +02:00
Jagan Teki
40ee163cc4 configs: icorem6: Use imx6 cratch register for bootcount
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.

Fixes: 4eb9aa3935 ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2019-03-31 20:12:37 +02:00
Michael Trimarchi
8b9cba0295 configs: icore: Fix U-Boot proper loading from nand
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.

So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-03-31 20:04:31 +02:00