Commit graph

67 commits

Author SHA1 Message Date
Nishanth Menon
8a0c6d6fa9 OMAP: common: consolidate fake USB ethernet MAC address creation
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.

Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.

NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 14:39:54 -04:00
Nishanth Menon
3ac8c0bf65 DRA7: Add support for ES1.1 silicon ID code
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Jassi Brar
02c41535b6 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL
The commit
 f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:34:22 -05:00
Roger Quadros
8ffcf74bb0 ARM: OMAP5: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on OMAP5.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
SRICHARAN R
39302dcd30 ARM: DRA7: Add is_dra7xx cpu check definition
A generic is_dra7xx cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:07 -05:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Matt Porter
c97a9b3275 omap5: add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:50 +05:30
Lokesh Vutla
e22cc0cf13 ARM: OMAP5: Avoid writing into LDO SRAM bits
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.

Boot tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Taras Kondratiuk
696f81f9a9 ARM: OMAP4470: Add OMAP4470 identification
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
f986d97208 ARM: DRA7xx: Enable GMAC clock control
Enabling CPSW module by enabling GMAC clock control

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Lokesh Vutla
65e9d56fb9 ARM: DRA7xx: Lock DPLL_GMAC
Locking DPLL_GMAC

[mugunthanvnm@ti.com:Configure only if CPSW is selected]

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Lubomir Popov
ee28edac43 OMAP5: Enable access to auxclk registers
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.

Also remove unrelated TPS62361 defines from clocks.h

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10 08:54:46 -04:00
Sricharan R
92b0482c17 ARM: DRA7xx: EMIF: Change settings required for EVM board
DRA7 EVM board has the below configuration. Adding the
settings for the same here.

   2Gb_1_35V_DDR3L part * 2 on EMIF1
   2Gb_1_35V_DDR3L part * 4 on EMIF2

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
e9d6cd042d ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc's
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Nishanth Menon
18c9d55ac6 ARM: OMAP5: DRA7xx: support class 0 optimized voltages
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.

This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.

This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
63fc0c775c ARM: DRA7xx: power Add support for tps659038 PMIC
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
4ca94d8186 ARM: OMAP4+: pmic: Make generic bus init and write functions
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
4d0df9c1e9 OMAP3+: introduce generic ABB support
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:

* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
  performance at the cost of power.  Used to operate safely at high
  OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
  save power.  Used to save power at lower OPPs.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2013-06-10 08:43:09 -04:00
Tom Rini
edfcf85a0a am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>
The location of valid scratch space is dependent on SoC, so move that
there.  On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR.  On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space.  Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-06 08:57:45 -04:00
SRICHARAN R
4a0eb75752 ARM: OMAP: Cleanup boot parameters usage
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
fda06812a0 ARM: OMAP: Correct save_boot_params and replace with 'C' function
Currently save_boot_params saves the boot parameters passed
from romcode. But this is not stored in a writable location
consistently. So the current code would not work for a
'XIP' boot. Change this by saving the boot parameters in
'gd' which is always writable. Also add a 'C' function
instead of an assembly code that is more readable.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
f92f2277a6 ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines common
These defines are same across OMAP4/5. So move them to
omap_common.h. This is required for the patches that
follow.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
Lokesh Vutla
0b1b60c779 ARM: OMAP5: Fix warm reset with USB cable connected
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-05-10 08:25:55 -04:00
Lokesh Vutla
de62688bb6 arm: dra7xx: Add silicon id support for DRA752 soc
Adding CPU detection support for the DRA752 ES1.0 soc.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:39:57 -04:00
Lokesh Vutla
8b12f1779e arm: dra7xx: Add control module changes
Control module register addresses are changed from OMAP5
to DRA7XX socs.
So adding the necessary changes for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
ea8eff1fe0 arm: dra7xx: clock: Add the dplls data
A new DPLL DDR is added in DRA7XX socs. Now clocks to
EMIF CD is from DPLL DDR. So DPLL DDR should be locked
before initializing RAM.
Also adding other dpll data which are different from OMAP5 ES2.0.
SYS_CLK running at 20MHz is introduced in DRA7xx socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4e4129c31 arm: dra7xx: clock: Add the prcm changes
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX.
So adding the necessary register changes for DRA7XX socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4d986ee27 ARM: OMAP5: srcomp: enable slew rate compensation cells after powerup
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
	 The 1 in wkup domain is not enabled because smart i/os
	 of wkup domain work with default compensation code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
SRICHARAN R
47abc3df70 ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendum
Change OPP settings as per the latest 0.5 version of
addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched
here to add dummy dividers.

While here correcting OPP_NOM mpu, core frequency for
OMAP4430 ES2.x

Note that OMAP5430 ES1.0 support is still kept alive and
would be removed in a cleanup later.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
afc2f9dcf1 ARM: OMAP5: clock: Add the prcm register changes required for ES2.0
PRCM register addresses are changed from ES1.0 to ES2.0 due to
PER power domain getting moved to CORE power domain.

So adding the nessecary register changes for the same.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
eed7c0f727 ARM: OMAP5: Add silicon id support for ES2.0 revision.
Adding the CPU detection suport for OMAP5430 and
OMAP5432 ES2.0 SOCs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2013-03-11 11:06:10 -04:00
Lokesh Vutla
c43c8339fe ARM: OMAP4+: Make control module register structure generic
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
3fcdd4a5f8 ARM: OMAP4+: Clean up the pmic code
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
ee9447bfe3 ARM: OMAP4+: Cleanup the clocks layer
Currently there is quite a lot of code which
is duplicated in the clocks code for OMAP 4 and 5
Socs. Avoiding this here by moving the clocks
data to a SOC specific place and the sharing the
common code.

This helps in addition of a new Soc with minimal
changes.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:09 -04:00
SRICHARAN R
01b753ff7b ARM: OMAP4+: Change the PRCM structure prototype common for all Socs
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.

Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11 11:06:09 -04:00
Tom Rini
f0881250f9 ARM: SPL: Make spl_mmc.c more generic
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>.  Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:58 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Tom Rini
8082fda9fc ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.c
This detection code doesn't (and can't) do anything currently, so
remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
37189a1958 ARM: SPL: Rename omap_boot_mode to spl_boot_mode()
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
8e1b836ec5 ARM: SPL: Rename omap_boot_device to spl_boot_device
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Tom Rini
861a86f460 omap-common: SPL: Add CONFIG_SPL_DISPLAY_PRINT / spl_display_print()
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing.  Change how this works to
be opt-in and only turned on for omap4/5 now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Tom Rini
0689a2ef19 am33xx: Correct MMC1, remove MMC2 support
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Lokesh Vutla
0a0bf7b217 OMAP5: ADD chip detection for OMAP5432 SOC
This patch adds chip detection for OMAP5432

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07 14:07:23 +02:00
Balaji T K
f75231b79a arm: omap5: correct boot device mode7 for eMMC
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:25 +02:00