Add missing information to the configuration section of the setexpr
man-page.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
-----BEGIN PGP SIGNATURE-----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=FY9O
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2023-04-rc1-3
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
Extend support for signing in auto-generated (-f auto) FIT. Previously,
it was possible to get signed 'images' subnodes in the FIT using
options -g and -o together with -f auto. This patch allows signing
'configurations' subnodes instead of 'images' ones (which are hashed),
using option -f auto-conf instead of -f auto. Adding also -K <dtb> and
-r options, will add public key to <dtb> file with required = "conf"
property.
Summary:
-f auto => FIT with crc32 images
-f auto -g ... -o ... => FIT with signed images
-f auto-conf -g ... -o ... => FIT with sha1 images and signed confs
Example: FIT with kernel, two device tree files, and signed
configurations; public key (needed to verify signatures) is
added to u-boot.dtb with required = "conf" property.
mkimage -f auto-conf -A arm -O linux -T kernel -C none -a 43e00000 \
-e 0 -d vmlinuz -b /path/to/first.dtb -b /path/to/second.dtb \
-k /folder/with/key-files -g keyname -o sha256,rsa4096 \
-K u-boot.dtb -r kernel.itb
Example: Add public key with required = "conf" property to u-boot.dtb
without needing to sign anything. This will also create a useless FIT
named unused.itb.
mkimage -f auto-conf -d /dev/null -k /folder/with/key-files \
-g keyname -o sha256,rsa4096 -K u-boot.dtb -r unused.itb
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move section 'Directory hierarchy' from file README to the HTML
documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the README section to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use internal rst reference with :doc: to have a link to distro.rst page
in the generated U-Boot documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
* Indicate the location of the directory for EFI capsules.
* Improve the readability.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* add return values
* move configuration to separate section to match other man-pages
* fix typo
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the sleep command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'Example' heading should be on a lower level than 'bdinfo command'.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the CROSS_COMPILE flag as we assume we build in a cross environment.
Also improve the comment about copying the binary to SD card.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This adds a guide for copying the raw bootloader image on the SD card
to the SPI NOR using U-Boot itself.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Use the latest version of the NXP TF-A code and add a note about
quirks with GCC 12.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Convert Note: to ..note::
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
Provide a man-page for the bdinfo command
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the blkcache command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the source command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
This implements the following command:
part type mmc 0:1
-> print partition type UUID
part type mmc 0:1 uuid
-> set environment variable to partition type UUID
"part type" can be useful when writing a bootcmd which searches for a
specific partition type to enable automatic discovery of partitions and
their intended usage or mount point.
Signed-off-by: Enric Balletbo i Serra <eballetbo@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix when CONFIG_PARTITION_TYPE_GUID is disabled and have the
command check for "types" before "type"]
Signed-off-by: Tom Rini <trini@konsulko.com>
Change the string 'a optionnal' to 'an optional'.
Signed-off-by: Enric Balletbo i Serra <eballetbo@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function arch_cpu_init_dm was renamed to fsp_setup_pinctrl in these
cases, so rename debug / docs to match.
Cc: Simon Glass <sjg@chromium.org>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
Added docs about sm efusedump command, that reads bytes
from efuse memory bank and print them to the console.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230110105650.54580-6-avromanov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
The gpio_hog_probe_all() functionality can be perfectly well replaced by
DM_FLAG_PROBE_AFTER_BIND DM flag, which would trigger .probe() callback
of each GPIO hog driver instance after .bind() and thus configure the
hogged GPIO accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Make sure the 'exit' command as well as 'exit $val' command exits
from environment scripts immediately and propagates return value
out of those scripts fully. That means the following behavior is
expected:
"
=> setenv foo 'echo bar ; exit 1' ; run foo ; echo $?
bar
1
=> setenv foo 'echo bar ; exit 0' ; run foo ; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2' ; run foo ; echo $?
bar
0
"
As well as the followin behavior:
"
=> setenv foo 'echo bar ; exit 3 ; echo fail'; run foo; echo $?
bar
3
=> setenv foo 'echo bar ; exit 1 ; echo fail'; run foo; echo $?
bar
1
=> setenv foo 'echo bar ; exit 0 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit -1 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit ; echo fail'; run foo; echo $?
bar
0
"
Fixes: 8c4e3b79bd ("cmd: exit: Fix return value")
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
This adds the UUU UCmd functionality as an OEM command. While the
fastboot tool allows sending arbitrary commands as long as they are
prefixed with "oem". This allows running generic U-Boot commands over
fastboot without UUU, which is especially useful when not using USB.
This is really the route we should have gone in the first place when
adding these commands.
While we're here, clean up the UUU Kconfig a bit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Adds DT binding documentation for the TI Error Location Module.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-8-rogerq@kernel.org
Add DT binding documentation for the TI GPMC NAND controller.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-4-rogerq@kernel.org
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To make things more human readable, say "changesets from" rather than
"csets from" in all our historical pages here. Moving forward this has
been changed in our gitdm with b034e399e31a ("gitdm: fix typo csets").
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sphinx supports generating Texinfo sources and Info documentation,
which can be navigated easily and is convenient to search (via the
indexed nodes or anchors, for example). This is basically the same as
1f050e904dd6f2955eecbd22031d912ccb2e7683, which was recently applied
to the Linux kernel.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale
PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Texas Instrument's entire K3 generation of SoCs use much of the same
frameworks and boot flow, especially at the uboot level. Though there
are small differences introduced as each new K3 based SoC is developed
and as the K3 generation matures that will also need to be documented.
Rather than copying the same documentation, with the small differences
applicable to that specific SoC to a new page, introduce a new K3
page that can describe the general boot flow and design decisions for
the entire K3 generation of chips, leaving the specifics for that
particular SoC to a unique sub-page below this one.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Texas Instruments produces quite a lot of SoCs based upon a common
architecture 'generation'. (eg: OMAP, K3) TI's existing documentation
layout makes noticing this generation jump rather difficult.
To make navigation easier, split the existing documentation into
individual SoC families so we may begin grouping them according to their
generational (eg: OMAP, K3) families.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_MONITOR_IS_IN_RAM
As part of this, reword some of the documentation slightly to reflect
that this is in Kconfig and not a define now.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FLASH_SPANSION_S29WS_N
CONFIG_FLASH_VERIFY
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
CONFIG_FSL_ISBC_KEY_EXT
CONFIG_FSL_TRUST_ARCH_v1
CONFIG_FSL_SDHC_V2_3
CONFIG_MAX_DSP_CPUS
CONFIG_MIU_2BIT_INTERLEAVED
CONFIG_SERIAL_BOOT
CONFIG_SPI_BOOTING
CONFIG_X86EMU_RAW_IO
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only used on one platform currently. However, with PHYLIB
enabled, which this platform also does, this option is not checked and
the functional use case is handled. Remove this code.
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'Configuration' heading should be on level 2, not on level 1.
Fixes: eaa268589e ("doc: man-page for the printenv command")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently the sound command accepts only one value each for duration and
frequency. Allowing more duration and frequency arguments enables playing a
tune.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI Conformance Profile Table entry for EBBR appears in v2.1.0 of the
EBBR specification[1]. Update naming accordingly.
While at it, update the EBBR version referenced in the documentation.
[1]: https://github.com/ARM-software/ebbr/releases/tag/v2.1.0
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix a few typos spot during a first read of the contribution process.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Since the commit d5ba6188df ("cmd: pxe_utils: Check fdtcontroladdr
in label_boot") the FDT or the FDTDIR label is required in extlinux.conf
and the fallback done by bootm command when only the device tree present
in this command parameters is no more performed when FIT is used for
kernel.
When the label FDT or FDTDIR are absent or if the device tree file is
absent, the PXE command in U-Boot uses the default U-Boot device tree
selected by fdtcontroladdr = gd->fdt_blob, it is the "Scenario 3".
With this scenario the bootm FIP fallback is no more possible with
the extlinux.conf when only "kernel" label is present and is a FIP:
kernel <path>#<conf>[#<extra-conf[#...]]
As the U-Boot FDT is always provided in the third bootm argument,
the device tree found in FIP is not used as fallback, it was done
previously in boot_get_fdt().
This patch adds a new field kernel_label to save the full kernel label.
The FDT bootm parameters use the kernel address (to avoid to load a
second time the same FIP) and the config when this full label is reused
for "fdt" or "initrd" label.
This FIP support in extlinux.conf is restored when the "FDT" label
can be found and select the same FIP (identical file and configuration):
kernel <path>#<conf>[#<extra-conf[#...]]
fdt <path>#<conf>[#<extra-conf[#...]]
The patch add also this possibility for initrd.
initrd <path>#<conf>[#<extra-conf[#...]]
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the sound command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commits adds the description for the UEFI Secure Boot
Configuration through the eficonfig menu.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Redacted the complete document.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* BASH code should be labeled as such.
* Code blocks should be indented by 4 spaces.
Fix these here.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add documentation for the wget command.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Convert the buildman documentation to rST format and include it in the
'build' section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <foss+uboot@0leil.net>
The word tuples might be misleading.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add example command how to compile U-Boot and add new documentation section
describing how to enable early debug UART and verbose log output for N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Sphinx 5.0 and later fails to build when language is set to None:
Warning, treated as error:
Invalid configuration value found: 'language = None'. Update your configuration to a valid langauge code. Falling back to 'en' (English)
Let's set the language to English since it is the language used for the
documentation.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a man-page for the bootd command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the symbol SYS_JFFS2_SORT_FRAGMENTS to Kconfig and use the only
remaining part of doc/README.JFFS2 that is still relevant and useful to
the help for this option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This removes the following symbols:
CONFIG_RTC_MCFRRTC
CONFIG_SYS_JFFS2_FIRST_BANK
CONFIG_SYS_JFFS2_FIRST_SECTOR
CONFIG_SYS_JFFS2_NUM_BANKS
CONFIG_SYS_LBC_CACHE_BASE
CONFIG_SYS_LIME_SIZE
CONFIG_SYS_MAMR
CONFIG_SYS_MCFRRTC_BASE
CONFIG_SYS_MONITOR_SEC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When running unit tests, some may have side effects which cause a
subsequent test to break. This can sometimes be seen when using 'ut dm'
or similar.
Add a new argument which allows a particular (failing) test to be run
immediately after a certain number of tests have run. This allows the
test causing the failure to be determined.
Update the documentation also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'ut info' command to show the number of suites and tests. This is
useful to get a feel for the scale of the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
File name with pattern u-boot-spl* is used on all places except in kwb
image for binary with SPL-only code. Combined binary with both SPL and
proper U-Boot in other places has file name pattern u-boot-with-spl*.
Make it consistent also for kwb image and rename u-boot-spl.kwb to
u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code.
Also update documentation about file name changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Documentation:
* Provide a document about security issue handling.
UEFI:
* Let networking support depend on NETDEVICES.
* Discover if no efi_system_partition is set.
Other:
* MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
-----BEGIN PGP SIGNATURE-----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=MoPl
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-01-rc1-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-01-rc1-4
Documentation:
* Provide a document about security issue handling.
UEFI:
* Let networking support depend on NETDEVICES.
* Discover if no efi_system_partition is set.
Other:
* MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
Based loosely on the Linux kernel
Documentation/admin-guide/security-bugs.rst file, create a basic
security document for U-Boot. In sum, security issues should be
disclosed in public on the mailing list if at all possible as an initial
position.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The output of the sbi command has been changed since the last release of
the man-page. Update the example.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The struct is only used to overlay the MMIO region, so the behavior is
the same. This obsoletes the Kconfig option for the number of ports.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Add documentation for the FWU Multi Bank Update feature. The document
describes the steps needed for setting up the platform for the
feature, as well as steps for enabling the feature on the platform.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for setting OEM flags in the capsule header. As per the
UEFI specification, bits 0-15 of the flags member of the capsule
header can be defined per capsule GUID.
The oemflags will be used for the FWU Multi Bank update feature, as
specified by the Dependable Boot specification[1]. Bit
15 of the flags member will be used to determine if the
acceptance/rejection of the updated images is to be done by the
firmware or an external component like the OS.
[1] - https://git.codelinaro.org/linaro/dependable-boot/mbfw/uploads/6f7ddfe3be24e18d4319e108a758d02e/mbfw.pdf
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The Dependable Boot specification[1] describes the structure of the
firmware accept and revert capsules. These are empty capsules which
are used for signalling the acceptance or rejection of the updated
firmware by the OS. Add support for generating these empty capsules.
[1] - https://git.codelinaro.org/linaro/dependable-boot/mbfw/uploads/6f7ddfe3be24e18d4319e108a758d02e/mbfw.pdf
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Add a command to read the metadata as specified in the FWU
specification and print the fields of the metadata.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Add bindings needed for accessing the FWU metadata partitions. These
include the compatible string which point to the access method and the
actual device which stores the FWU metadata.
The current patch adds basic bindings needed for accessing the
metadata structure on GPT partitioned block devices.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for filtering out FIT images by phase. Rather than adding yet
another argument to this already overloaded function, use a composite
value, where the phase is only added in if needed.
The FIT config is still selected (and verified) as normal, but the images
are selected based on the phase.
Tests for this come in a little later, as part of the updated VPL test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to mark an image as related to a phase, so we can
easily load all the images for SPL or for U-Boot proper.
Add this to the FIT specification, along with some access functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.
Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a couple of places the document says u-boot,pre-reloc but all
examples show u-boot,dm-pre-reloc, use the latter consistently.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
GPMC stands for General Purpose Memory Controller and it is
present on many Texas Instruments SoCs.
It supports a number of Asynchronous and Synchronous interfaces
and has various settings to configure the bus interface.
The DT bindings define all the various GPMC settings.
As the GPMC supports multiple devices on the bus, each
device is represented as a child and the respective
GPMC settings are situated there. (see ti,gpmc-child.yaml)
These binding docs are picked up from the Linux kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
This is a companion to u-boot,noautostart. If one has a single
watchdog device that one does want to have auto-started, but several
others that one doesn't, the only way currently is to set the
CONFIG_WATCHDOG_AUTOSTART and then use the opt-out for the majority.
The main motivation for this is to add an autostarted watchdog device
to the sandbox (to test a fix) without having to set AUTOSTART in
sandbox_defconfig and add the noautostart property to the existing
devices. But it's also nice for symmetry, and the logic in
init_watchdog_dev() becomes simpler to read because we avoid all the
negations.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
When a FIT includes some OS requests, U-Boot should process these and add
the requested info to corresponding subnodes of the /chosen node. Add a
pytest for this, which sets up the FIT, runs bootm and then uses a C
unit test to check that everything looks OK.
The test needs to run on sandbox_flattree since we don't support
device tree fixups on sandbox (live tree) yet. So enable BOOTMETH_VBE and
disable bootflow_system(), since EFI is not supported on
sandbox_flattree.
Add a link to the initial documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this function's comment and also the livetree documentation, so it
is clear when to use the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The working FDT is the one which comes from the OS and is fixed up by
U-Boot. When the bootm command runs, it sets up the working FDT to be the
one it is about to pass to the OS, so that fixups can happen.
This seems like an important step, so add a message indicating that the
working FDT has changed. This is shown during the running of the bootm
command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add xxd command to print file content as hexdump to standard out
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Roger Knecht <rknecht@pm.me>
This adds keyword devicetree-overlay as an alias for fdtoverlays in
extlinux (sysboot) and pxe to better follow the Boot Loader Specification
[1], improves documentation around them by adding an example for both
fdtoverlays and devicetree-overlay and the environment variable required
for this feature. The link for the spec is updated to the current one.
[1] https://systemd.io/BOOT_LOADER_SPECIFICATION/
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We want tests to avoid the usage of sudo. Describe that virt-make-fs can
generate disk images without being root.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Packages python3-filelock python3-pytest-xdist as required to run
'make tests'. Add them to the required packages list in the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the cls command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently
commented out, so there are no users for this macro:
#if 1
#define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r2")
#else /* We could use plain global data, but the resulting code is bigger */
#define XTRN_DECLARE_GLOBAL_DATA_PTR extern
#define DECLARE_GLOBAL_DATA_PTR XTRN_DECLARE_GLOBAL_DATA_PTR \
gd_t *gd
#endif
Remove all references to this macro, but add a documentation note regarding
the possibility of using plain global data for the GD pointer.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
* Convert code comments in include/efi_driver.h to Sphinx style.
* Add include/efi_driver.h to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present ofnode_write_prop() is inconsistent between livetree and
flattree, in that livetree requires the caller to ensure the property
value is stable (e.g. in rodata or allocated) but flattree does not, since
it makes a copy.
This makes the API call a bit painful to use, since the caller must do
different things depending on OF_LIVE.
Add a new 'copy' argument which tells the function to make a copy if
needed. Add some tests to cover this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current tests do not cover all functions, nor do they cover the new
multi-tree functionality. Add and update the tests accordingly and update
the 'future work' notes in the documentation.
There is a still more testing needed for the failure cases, since at
present some ofnode functions return a libfdt error code instead of
converting it to an errno.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the logic to redirect requests for the device tree through a function
which can look up the tree ID. This works by using the top bits of
ofnode.of_offset to encode a tree.
It is assumed that there will only be a few device trees used at runtime,
typically the control FDT (always tree ID 0) and possibly a separate FDT
to be passed the OS.
The maximum number of device trees supported at runtime is 8, with this
implementation. That would use bits 30:28 of the node-offset value,
meaning that the positive offset range is limited to bits 27:0, versus
30:1 with this feature disabled. That still allows a device tree of up
to 256MB, which should be enough for most FITs. Larger ones can be
supported by using external data with the FIT, or by enabling OF_LIVE.
Update the documentation a little and fix up the comment for
ofnode_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
Complete the list of commands influenced by the autostart environment
variable.
Make it clearer what values qualifies at 'yes'.
Eventually the list of environment variables is to be alphabetically
sorted. Move autostart up.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the flat device tree changes it can mess up the live tree since that
uses the flat tree for its strings. This affects only a few sandbox tests
which modify the device tree, but the number will grow as ofnode support
for writing improves.
While the control FDT is not intended to change while U-Boot is running,
some tests do so. For example, the ofnode interface only supports
modifying properties in the control FDT, so tests must use that.
To solve this problem, keep a copy of the FDT and restore it as needed
when the test is finished. The copy only happens on sandbox (except SPL
builds), to reduce memory usage and because these tests are not useful on
other boards. For other boards, a checksum is taken to ensure that nothing
changes.
It would be possible to always checksum the FDT on sandbox and only
restore it if needed, but this is slightly slower than restoring it every
time, at least with crc8.
Move the code which checks for success to the very end, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running the script to sign SPL/U-Boot on a kontron-sl-mx8mm board,
the fit_block_size was calculated as 0x1000 instead of 0x1020.
Add an extra parenthesis pair to fix it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add HABv4 documentation extension for SPL targets covering the
following topics:
- How to sign an securely boot an flash.bin container image.
- How to extend the root of trust for additional boot images.
- Add SPL and fitImage CSF examples.
- Add signature generation script example.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Disable UBI fastmap support which is not supported by original Maemo 5
kernel and explicitly set UBI BEB limit to 10%, which is the value used by
original Maemo 5 kernel. U-Boot default value is 20%.
Signed-off-by: Pali Rohár <pali@kernel.org>
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
-----BEGIN PGP SIGNATURE-----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=P89S
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
The bootmenu enumerates the UEFI boot options
for boot device selection.
This commit adds the description how the UEFI boot work
in bootmenu. This commit also adds "Synopsis", "Description"
and "Configuration" sections to follow the U-Boot command
documentation format.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add documentation for the cyclic function infrastructure, including the
cyclic command.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Running tests in parallel is much faster, e.g. 15 seconds to run the tests
on sandbox (only), instead of 100 seconds (on a 16-core machine). Add a
'make pcheck' option to access this feature.
Note that the tools/ tests still run each tool's tests once after the
other, although within that, they do run in parallel. So for example,
the buildman tests run in parallel, then the binman tests run in
parallel. There would be a signiificant advantage to running them all
in parallel together, but that would require a large amount of
refactoring, e.g. with more use of pytest fixtures.
Update the documentation to represent the current state.
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* man-page for tftpput
UEFI:
* fix driver binding protocol for block IO devices
* don't delete invalid handles
* add a unit test for the EFI Conformance Profile Table
Other:
* correct short text for tftpboot
-----BEGIN PGP SIGNATURE-----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=1zZW
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-10-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-10-rc5
Documentation:
* man-page for tftpput
UEFI:
* fix driver binding protocol for block IO devices
* don't delete invalid handles
* add a unit test for the EFI Conformance Profile Table
Other:
* correct short text for tftpboot
Provide a man-page for the tftpput command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Add bindings needed for accessing the FWU metadata regions.
These include the compatible string which point to the access
method, the actual device which stores the FWU metadata and
the offsets for both metadata regions.
The current patch adds basic bindings needed for accessing the
metadata structure on non-GPT mtd regions.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
- Use gender-neutral language to refer to the user, consistently.
- Reference the checkpatch document.
- Move the section on commit message tags to the process document and
reference this in sending_patches.rst.
- Reword the custodian workflow process section to refer to this new
section, integrate some of the wording from there in this new section.
- Update the comment about GPLv2 applying to August 2022, to be clear
this still is correct.
- Reword the section about MAKEALL to talk about local build testing and
link to the CI document.
- Reference the system_configuration document for the note about
modifying existing code.
- Reword the patchwork flow section.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Import as-is much of the old "Patches" wiki page to the current
sending_patches.rst file. This means we need to move patman to being
included in the higher level ToC and add a reference for "Custodians" in
the process document. A very minimal amount of content changing and
rewording is done here as part of the import, in order to make the
conversion easier.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add gpio status output fields description and one output example.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tweak the formatting.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
With the addition of the revision stats this now takes over a minute. Use
a parallel build to reduce it a bit (24 seconds for me).
Series-changes; 2
- Use '-j auto' instead
Signed-off-by: Simon Glass <sjg@chromium.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Explain when devices should get activated.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The ELF U-Boot image produced by qemu-riscv64_smode_defconfig can be
used to boot with QEMU and KVM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is an attempt to answer the comments provided by Xavier [1].
[1] https://lore.kernel.org/all/Yulcol7HpTHtjXTX@begut/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Link to patman's documentation from the doc/ directory so that it appears
in the 'make htmldocs' output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This was widely used by U-Boot for a long time, but is not used anymore,
with Gitlab and Azure taking over.
Drop the text.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We talk about importing code from other projects in two places. The
first place is in the coding style section, where we explain when to or
not to deviate in terms of white space, etc. In the process
documentation we now add a note about saying where the code was imported
from and to ensure that you do not copy Signed-off-by or other tags.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* describe crashs in UEFI binaries
* provide architechture specific information for the sandbox and RISC-V
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These typos were found while reading the docs.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Remove alias 'efi' with invalid data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some documentation and a new flag so that we can safely enabled using
the ofnode interface to write to the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
The unflattening algorithm results in a single block of memory being
allocated for the whole tree. When writing new properties, these are
allocated new memory outside that block. When the block is freed, the
allocated properties remain.
Document how this works and the potential memory leak, as well as
mentioning that updating the livetree is actually supported now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few links to documents about Verified Boot for Embedded (VBE).
These will be expanded as development proceeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed now that CONFIG_SYS_TARGET_NAME is correctly determined
when scanning Kconfig.
This reverts commit 25b8acee2e.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a large number of options under CONFIG_SYS (but some of these
are elsewhere, spotted while cleaning CONFIG_SYS) that are never
referenced, or only used slightly later in the config file. Remove or
restructure these.
Signed-off-by: Tom Rini <trini@konsulko.com>
Start by describing in general the best practices for how to implement
configuration of some aspect of U-Boot. This generally means finding
the right choices for when something should be static or dynamically
configured and enabled. Then further document when to use CONFIG or CFG
namespaces for static configuration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Describe exactly which bytes are hashed and in what order
when signing a configuration.
Signed-off-by: Martin Bonner <martingreybeard@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Start by elaborating on what some of our constraints tend to be with
image location values, and document where these external constraints
can come from. Provide a new subsection, an example based on the TI
ARMv7 OMAP2PLUS families of chips, that gives sample values and explains
why we use these particular values. This is based on what is in
include/configs/ti_armv7_common.h as of fb3ad9bd92 ("TI: Add, use a
DEFAULT_LINUX_BOOT_ENV environment string") as this contains just the
values referenced in this document now and not some of the further
additions that are less generic.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
When CONFIG_LOG is activated, if LOG_DEBUG is defined in a file and
DEBUG is not defined the trace with debug() macro are not displayed,
because the parameter cond : _DEBUG = 0 is checked in debug_cond().
With this patch the define DEBUG, used to force the trace generated by
debug() macro, is linked with the define LOG_DEBUG, used to force the
trace generated by other macros (log_debug, dev_dbg, pr_debug).
We only need to define LOG_DEBUG in a file to activate all the
traces generated by any U-Boot debug macro, as it is described in
/doc/develop/logging.rst
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add supporting new compatible string "u-boot,zynqmp-fpga-enc" to
handle loading encrypted bitfiles.
This feature requires encrypted FSBL, as according to UG1085:
"The CSU automatically locks out the AES key, stored in either BBRAM
or eFUSEs, as a key source to the AES engine if the FSBL is not
encrypted. This prevents using the BBRAM or eFUSE as the key source
to the AES engine during run-time applications."
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-14-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add instructions to build and boot from QSPI Flash
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
%s/formatted/format/
Fixes: 4211fb2ef6 ("doc: Migrate CodingStyle wiki page to Sphinx")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The wiki had gitdm-generated release statistics starting with v1.3.0.
Re-generate this information as Sphinx. This aims to be as historically
accurate as possible and so some company renames were kept to their old
rather than current name until we had made the switch previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
For quite a long time we've been using a 3 week, rather than 2 week,
merge window as it was only 2 weeks during the timeframe where we did 2
month rather than 3 month releases. This corrects the places that still
had 2 weeks and tries to make things a bit clearer overall.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the RelaseCycle wiki page to Sphinx. In terms of visible
changes, we stop having a dynamic countdown to when the release is. And
we drop the year-based statistics, that were not being kept up to date.
For the moment, we only link to statistics for v2022.07 but will add
back the historical data in a subsequent patch.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "Workflow of a Custodian" section on the wiki had not been changed
in quite some time to reflect how the process has been functioning for
some time. First, update some links to point to modern and current
sources of information.
Second, and more overarching, reword much of the section. This expands
on the expectations of both custodians and developers when it comes to
rebasing patches. Rework the final points to be clearer that Custodians
are expected to do their best to test the changes and ask for help when
needed, as well as that pull requests are expected in a timely manner.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Use gender-neutral language to refer to the user, consistently.
- Reword a few places so that they read more naturally.
- Make the long standing practice around "Twilight Time" more clear,
hopefully.
- Replace a reference to MAKEALL with a reference to CI testing as
that's the current requirement.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove some missed wiki markup, and escape a "\n" correctly.
- Use gender-neutral language to refer to the user, consistently.
Cc: Claudius Heine <ch@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current Process wiki page to doc/develop/process.rst. The
changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
For some time now we've allowed for '//' style comments, which mirrors
the Linux kernel. So drop this point here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current DesignPrinciples wiki page to
doc/develop/designprinciples.rst. The changes here are for formatting
or slight rewording so that it reads well when linking to other Sphinx
documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current CodingStyle wiki page to doc/develop/codingstyle.rst.
The changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MT7621 requires external binary blob being executed during u-boot's
boot-up flow. It's necessary to provide a guide here for users to correctly
build the u-boot.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Our statistics pages have always been generated by gitdm. After
patching gitdm to generate an acceptable Sphinx output for tables,
include that and some other basic formatting here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Explain why fdt_addr and initrd_addr should not be set to disable
relocation normally.
- Provide some advice on the typical loadaddr default value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This variable is never set nor explained why it would be set, drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This tool seems a bit underloved. Unfortunately, it seems to be missing
support for FIT images. Alas...
Add a man page documenting it. The example is taken from commit a804b5ce2d
("Add dumpimage, a tool to extract data from U-Boot images").
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Despite the original description of these options, they are not always
image names, or even files. Some image types use these options to convey
configuration directly. Re-document these options as configuration options.
Additionally, add a new section documenting the format of the configuration
for each image type which uses it. In general, if configuration is used
directly (without a separate file) I have added documentation for it. If
the configuration points to a separate file, I have referenced that file's
documentation. Where there is no such documentation, I have added it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The mkimage command has had many options added over the years.
Unfortunately, we are starting to run out of short options. Recent options
don't have any obvious relation to their meaning (e.g. -o/-g). Fortunately,
long options exist. Add long options for each current short option.
For the curious, the remaining short options are HIkLmMPQSuUwWXyYzZ.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per man-pages(7), "use of an AUTHORS section is strongly discouraged."
Remove it, and instead add some copyright notices and an SPDX. The default
license for U-Boot is GPL2, so that's what I put. The copyright dates are
based on the commit dates.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a SEE ALSO section to link to similar man pages, as well as to
the U-Boot documentation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In leiu of a non-standard HOMEPAGE section, add a BUGS section with a link
to the issue tracker.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes a variety of changes for the options to make them
typographically consistent, clarify their meaning, and fix grammatical (or
other) errors. Many of the changes here are stylistic, though there are a
few fixes. The main changes I made across the board were:
- All options are bolded and parameters italicised
- All single quotes are properly matched (instead of using apostrophes)
- Minor background info has been added to clarify many underdocumented
options
- Default values for options are documented
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The description in NAME should not be capitalized. Fix a grammatical error
as well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves some options which work in any mode to the general options
section. -p is moved to after -E/-B since those options are related. This
also adds documentation for -h and -V.
The -F, -l, and -G options are documented twice. Remove the second
documentation in each case. The synopsis for -l also suggests an implied
second uimage-file-name parameter. E.g.
mkimage [-l uimage-file-name] uimage-file-name
This is misleading, so remove it. Wrap a few lines to 80 characters as
well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The options are divided up into several subsections. Use the appropriate
macro. While we're at it, rename the headings to better reflect the
contents of their sections.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Square brackets are commonly used to denote optional parts of a command.
However, all option arguments are mandatory. Remove these brackets. This
also removes some unnecessary quotation marks, and uses hyphens to connect
words in option arguments. This is intended to just clean up the
formatting, leaving content corrections to later patches.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This puts each example in a new paragraph and uses a hanging indent for
continued lines to increase clarity. We use tabs instead of .in or .RS for
the indent because it renders properly in both man and mandoc (which is
what many common HTML man pages use). The only nit is that the tab stops in
man default to something like 2", so reduce that to 1". We also escape
every "minus" as recommended by man-pages(7).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Blank lines do not have well-defined semantics in fill mode (the default).
Instead, use empty requests (.) where vertical space is necessary for
readability. There are a few places where we use a paragraph instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The synopsis section is a bit messy. As an example, "uimage file name" is
printed in italics, bold, and roman (depending on the line). This cleans
things up and converts the synopsis section to use standard style. The
.SY/.YS macros set up appropriate formatting for command synopsis sections
(such as disabling hyphenation and setting a hanging indent). All parts of
the synopsis now use the following style:
- Bold for parts of the command which should be typed in by the user (such
as the program name and flags)
- Italic for parts which should be replaced (such as uimage-file-name)
- Roman for parts which should not be typed at all (such as brackets)
Multi-word variables now use hyphens to connect their words instead of
spaces. This makes it clearer that all the words are part of the same
variable. Additionally, "option ..." is used to denote where other options
may be specified, as this appears to be standard style.
In addition to the above style changes, this also makes some changes to
content. The use of the term "legacy" has been removed, since this simply
refers to any non-FIT image type. Additionally, wording like "uimage file
name" has been replaced with "image-file-name" to better reflect that
images may or may not be uImages. Lastly, the "auto" value for -f is
documented in the synopsis.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a preliminary documentation introducing different
boot sequences, and notably the recovery mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220706093649.3261229-1-narmstrong@baylibre.com
Add a comment explaining the design goals of bloblist, to make it easier
for people to understand and comment on the structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.
So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.
ex: loadm $kernel_addr $kernel_addr_r $kernel_size
with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add in U-Boot documentation the quick instruction to
setup the STMicroelectronics STM32MP13x boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for signing images in auto-generated FITs. To do this,
we need to add a signature node. The algorithm name property already has
its own option, but we need one for the key name hint. We could have
gone the -G route and added an explicit name for the public key (like
what is done for the private key). However, many places assume the
public key can be constructed from the key dir and hint, and I don't
want to do the refactoring necessary.
As a consequence of this, it is now easier to add public keys to an
existing image without signing something. This could be done all along,
but now you don't have to create an its just to do it. Ideally, we
wouldn't create a FIT at the end. This could be done by calling
fit_image_setup_sig/info.crypto->add_verify_data directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Document -G and the secondary image types which can be used with -R.
Also reword the documentation of -s for clarity.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The actual support was added in commit fec8c900c8 ("power: regulator:
Add support for regulator-force-boot-off"), update the docs to include
this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OsIndications is a 64 bit variable, and the current code expects
the value of the variable to be 64 bit. Update the documentation to
reflect this fact.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
"valu" should be "value".
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The firmware management protocol can be used to manage device firmware.
U-Boot can be configured to provide an implementation.
Document the related functions in the API section.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For indicating the address and size of a memory region other commands use a
<addr>[:<size>] syntax. Do the same for bootefi.
Fixes: 2058983689 ("cmd: bootefi: restore ability to boot arbitrary blob")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This documents some additional options which can be used with valgrind, as
well as directions for future work. It also fixes up inline literals to
actually be inline literals (and not italics). The content of this
documentation is primarily adapted from [1].
[1] https://lore.kernel.org/u-boot/57cb4b49-fa30-1194-9ac3-faa53e8033bd@gmail.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The following Python packages are used by U-Boot, too:
* python3-asteval
* python3-subunit
* python3-testtools
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Image created by LTO is not friendly to debugger, let's document this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Mention CONFIG_CC_OPTIMIZE_FOR_DEBUG and LLDB.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It should be CONFIG_SANDBOX_RAM_SIZE_MB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Update unleashed.rst to remove the manual environment configuration
for compressed kernel boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
Over the years, several options have not made it into the help message.
Document them. Do the same for the man page.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
%s/cammand/command/
%s/sequencies/sequences/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
The '--args' parameter to gdb comes before the binary that the debugger
will be attached to rather than after the binary and before the
arguments. Fix that in the docs.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
A 'bootdev' is a device which can be used to boot an operating system.
It is a child of the media device (e.g. MMC) which handles reading files
from that device, such as a bootflow file.
Add a uclass for bootdev and the various helpers needed to make it
work. Also add a binding file, empty for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'bootstd' device provides the central information about U-Boot
standard boot.
Add a uclass for bootstd and the various helpers needed to make it
work. Also add a binding file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some basic stuff about tag support is explained under
doc/devlop/driver-model.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A image_size parameter has been added to the bootefi parameter.
Describe all parameters.
Correct how the description of how the device-path in the loaded
image protocol is determined.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Adds simple documentation about common properties for watchdog
in the device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via
devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add rk3066 Rikomagic MK808 to the list of
mainline supported Rockchip boards.
Include instructions for creating and programming
images to NAND and SD card.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are several PX30/RK3326 boards in use without
mentioning in rockchip.rst. Add boards and examples.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With more text coming to the rockchip.rst document,
give it a restyle first.
Changed:
sort build examples alphabetically
add git clone example
fix bash examples
fix phrases (grammer)
fix typos
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Update the capsule update functionality related documentation to
refect the additional definitions that need to be made per platform
for supporting the capsule update feature.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
While building a capsule, the GUID value of that specific image is to
be passed through the --guid command option to the mkeficapsule
tool instead of using one of --raw or --fit options, where the GUID
value passed through the command line option is the image GUID.
This renders the EFI_FIRMWARE_IMAGE_TYPE_UBOOT_FIT_GUID and
EFI_FIRMWARE_IMAGE_TYPE_UBOOT_RAW_GUID values superfluous. Remove the
--raw and --fit command line options as well. Also modify the
mkeficapsule man page to reflect this change.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add a driver which allows to use of LEDs connected
to PWM (Linux compatible).
MAINTAINERS: add i.vozvakhov as a maintainer of leds-pwm
C(required during new functionality adding).
Signed-off-by: Ivan Vozvakhov <i.vozvakhov@corp.mail.ru>
This documents how to get more detailed results from valgrind made possible
by the last two commits.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide settings for enabling the debug UART of the virt machine on
RISC-V QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* add link to booti man-page
* correct link description for efidebug command
* correct punctuation
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is an attempt to cover the common cases found when enabling driver
model for serial on a new board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Drop this text at the end since it already mentions bootp and dhcp.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This doesn't really make much sense in the documentation. Add a code
comment instead.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Unfortunately, we require additional logic to buildman to support this
removal and still use SYS_SOC, etc, for build targets.
This reverts commit eeec00072d.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This documents how to use semihosting, the new semihosting features, and
how to migrate from smhload.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds some instructions for enabling the debug uart, including the
correct address and clock rate.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds some additional info about booting from different sources,
including the correct switch positions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the semihosting readme to rST. I have tried to make only
cosmetic changes, but I did fix up the first link (which was broken).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
This converts the existing README.plan9 to reST, and puts it under
the doc/usage/os directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present the doc only mentions Arm, PowerPC and x86. RISC-V support
has been added since VxWorks SR0650 support for a while, and U-Boot
supports loading a RISC-V VxWorks kernel too. Let's document it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the existing README.vxworks to reST, and puts it under
the doc/usage/os directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update the extension command title for consistency with other commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently all shell command docs are put in the doc/usage root.
Let's group them into cmd/ sub-directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide human readable descriptions of the speed nodes instead of the name
of constants from the code as it is already done for 'mmc rescan'
command in commit 212f078496 ("doc: mmc rescan speed mode").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add documentation about the different configuration files for the
RaspberryPi board family.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There is no CONFIG_UEFI_SECURE_BOOT, and there was never any.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add section how to run U-Boot in n900 qemu machine.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
It add documentation on licencing & provides links to the amlogic-boot-fip
pre-built files collections.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Testes proved that current kwboot version supports also Avanta SoCs.
It looks like that Avanta SoCs are using same kwbimage format as Armada.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Document -D, -b, -d, -q and -s options.
Add common examples how to use kwboot.
Add information about Armada 38x BootROM bug for debug console mode and how
to workaround it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Changes SCMI bindings documentation to relate to Linux kernel
source tree that recently changed the bindings description to YAML
format.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Currently -l option for mkimage and dumpimage ignores option -T and always
tries to autodetect image type.
With this change it is possible to tell mkimage and dumpimage to parse
image file as specific type (and not random autodetected type). This allows
to use mkimage -l or dumpimage -l as tool for validating image.
params.type for -l option is now by default initialized to zero
(IH_TYPE_INVALID) instead of IH_TYPE_KERNEL. imagetool_get_type() for
IH_TYPE_INVALID returns NULL, which is assigned to tparams. mkimage and
dumpimage code is extended to handle tparams with NULL for -l option. And
imagetool_verify_print_header() is extended to do validation via tparams if
is not NULL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
They are no longer needed, because we now have proper driver support for
the sl28cpld management controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The watchdog timer is part of the sl28cpld management controller. The
watchdog timer usually supervises the bootloader boot-up and if it bites
the failsafe bootloader will be activated. Apart from that it supports
the usual board level reset and one SMARC speciality: driving the
WDT_TIMEOUT# signal.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
