Up to now, the function is_serdes_configed() doesn't check if the map
of serdes protocol is initialized before accessing it. The function
is_serdes_configed() will get wrong result when it was called before
the serdes protocol maps initialized. As the first element of the map
isn't used for any device, so use it as the flag to indicate if the
map has been initialized.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update erratum workaround for A006379 to set register CPCHDBCR0
with value 0x001e0000, replacing the old value 0x003c0000.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Dave Liu <dave.liu@nxp.com>
Add support for reading bootscript and bootscript header from SD. Also
renamed macros *_FLASH to *_DEVICE to represent SD alongwith NAND and
NOR flash.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Define a platform data structure for the MPC85XX GPIO driver to allow
use of the driver without device tree. Users should define the GPIO
blocks for their platform like this:
struct mpc85xx_gpio_plat gpio_blocks[] = {
{
.addr = 0x130000,
.ngpios = 32,
},
{
.addr = 0x131000,
.ngpios = 32,
},
};
U_BOOT_DEVICES(my_platform_gpios) = {
{ "gpio_mpc85xx", &gpio_blocks[0] },
{ "gpio_mpc85xx", &gpio_blocks[1] },
};
This is intended to build upon the recent submission of the base
MPC85XX driver from Mario Six. We need to use that new driver
without dts support and this patch gives us that flexibility.
This has been tested on a Freescale T2080 CPU, although only the first
GPIO block.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Chain of Trust is enabled for PowerPC platforms for Secure Boot.
CONFIG_BOARD_LATE_INIT is defined.
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are two phases in Secure Boot
1. ISBC: In BootROM, validate the BootLoader (U-Boot).
2. ESBC: In U-Boot, continuing the Chain of Trust by
validating and booting LINUX.
For ESBC phase, there is no difference in SoC's based on ARM or
PowerPC cores.
But the exit conditions after ISBC phase i.e. entry conditions for
U-Boot are different for ARM and PowerPC.
PowerPC:
If Secure Boot is executed, a separate U-Boot target is required
which must be compiled with a diffrent Text Base as compared to
Non-Secure Boot. There are some LAW and TLB settings which are
required specifically for Secure Boot scenario.
ARM:
ARM based SoC's have a fixed memory map and exit conditions from
BootROM are same irrespective of boot mode (Secure or Non-Secure).
Thus the current Secure Boot functionlity has been split into
two parts:
CONFIG_CHAIN_OF_TRUST
This will have the following functionality as part of U-Boot:
1. Enable commands like esbc_validate, esbc_halt
2. Change the environment settings based on bootmode, determined
at run time:
- If bootmode is non-secure, no change
- If bootmode is secure, set the following:
- bootdelay = 0 (Don't give boot prompt)
- bootcmd = Validate and execute the bootscript.
CONFIG_SECURE_BOOT
This is defined only for creating a different compile time target
for secure boot.
Traditionally, both these functionalities were defined under
CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement
for a separate Secure Boot target for ARM based SoC's.
CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be
determine at run time.
Another Security Requirement for running CHAIN_OF_TRUST is that
U-Boot environemnt must not be picked from flash/external memory.
This cannot be done based on bootmode at run time in current U-Boot
architecture. Once this dependency is resolved, no separate
SECURE_BOOT target will be required for ARM based SoC's.
Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is
defining CONFIG_ENV_IS_NOWHERE
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move arch/powerpc/include/asm/fsl_errata.h to include/fsl_errata.h
to make it public for both ARM and POWER SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix soc.h path in fsl_errata.h]
Reviewed-by: York Sun <yorksun@freescale.com>
Unify serial_ppc, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of headers define functions as "extern inline" which is
causing problems with gcc5. The reason is that starting with
version 5.1, gcc defaults to the standard C99 semantics for the
inline keyword.
Under the traditional GNU inline semantics, an "extern inline"
function would never create an external definition, the same
as inline *without* extern in C99. In C99, and "extern inline"
definition is simply an external definition with an inline hint.
In short, the meanings of inline with and without extern are
swapped between GNU and C99.
The upshot is that all these definitions in header files create
an external definition wherever those headers are included,
resulting in multiple definition errors at link time.
Changing all these functions to "static inline" fixes the problem
since this works as desired in all gcc versions. Although the
semantics are slightly different (a static inline definition may
result in an actual function being emitted), it works as intended
in practice.
This patch also removes extern prototype declarations for the
changed functions where they existed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Remove __ilog2_u64 and ffs4 from powerpc bitops to align with the
kernel implementation.
Use the generic __ffs64 instead of a custom powerpc implementation.
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This reverts commit 8fe11b8901.
I'll add support to lwmon5 in the next patch and will remove
support for the broken lcd4_lwmon5 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
ISBC Key Extension feature is not applicable for RAMBOOT
as there is no way to retrieve the CSF Header and validated
IE Key table from SRAM once CPC has been disabled.
The feature is only applicable in case of NOR SECURE BOOT.
Code Cleanup:
The SECURE_BOOT specific defines have been moved from
arch-ls102xa/config.h to
arm/include/asm/fsl_secure_boot.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Recently the FMan Port and MAC compatibles were changed.
This patch aligns the FMan Port and MAC compatibles
to the new FMan device tree binding document.
The FMan device tree binding document can be found in the Linux kernel:
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Tested-by: Xing Lei <xing.lei@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
For running Chain of Trust when doing Secure Boot from NAND,
the Bootscript header and bootscript must be copied from NAND
to RAM(DDR).
The addresses and commands for the same have been defined.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Correct the value CONFIG_USB_MAX_CONTROLLER_COUNT macro to 1
for p1025 as it has one USB controller
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MAC1 acts as 1G/10G dual-role MAC on T1024. We introduce
macro SET_FMAN_RX_10G_TYPE2_LIODN for 10G MACs which have
same Port ID and same offset of address with 1G MAC.
Update it to match with the setting of fman in t1024 device
tree, otherwise there is no 'fsl,liodn' in
/proc/device-tree/soc@ffe000000/fman@400000/port@88000/
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
defconfig files are added and SFP version for these platforms
is updated.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To replicate:
1. add to include/configs/p1_p2_rdb_pc.h "#define CONFIG_CMD_GPIO"
2. run `make P1020RDB-PC_defconfig`
3. run CROSS_COMPILE=powerpc-linux- make
and you will get:
common/built-in.o: In function `do_gpio':
u-boot/common/cmd_gpio.c:186: undefined reference to `gpio_request'
u-boot/common/cmd_gpio.c:194: undefined reference to `gpio_direction_input'
u-boot/common/cmd_gpio.c:195: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:200: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:203: undefined reference to `gpio_direction_output'
u-boot/common/cmd_gpio.c:209: undefined reference to `gpio_free
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale PCIe controllers v3.0 and later need to set bit
CFG_READY to allow all inbound configuration transactions
to be processed normally when in EP mode. However, bit
CFG_READY has been moved from PCIe configuration space to
CCSR PCIe configuration register comparing previous version.
The patch is to set this bit according to PCIe version.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.
Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale sfp has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
sfp_regs to common include. This patch also defines ccsr_sfp_regs
definition for newer versions of SFP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Modify CONFIG_USB_MAX_CONTROLLER_COUNT value to 1 on P1022DS.
As ETSEC2 and USB2 are muxed; thus if ETSEC2 is enabled, the
system bus hangs on USB2 if ETSEC2 is enabled but "usb start"
command is issued. Hence making default controller count to 1
to avoid system hang.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Yusong Sun <yorksun@freescale.com>
The code provides framework for heterogeneous multicore chips based on StarCore
and Power Architecture which are chasis-2 compliant, like B4860 and B4420
It will make u-boot recognize all non-ppc cores and peripherals like
SC3900/DSP CPUs, MAPLE, CPRI and print their configuration in u-boot logs.
Example boot logs of B4860QDS:
U-Boot 2015.01-00232-geef6e36-dirty (Jan 19 2015 - 11:58:45)
CPU0: B4860E, Version: 2.2, (0x86880022)
Core: e6500, Version: 2.0, (0x80400120)
Clock Configuration:
CPU0:1600 MHz, CPU1:1600 MHz, CPU2:1600 MHz, CPU3:1600 MHz,
DSP CPU0:1200 MHz, DSP CPU1:1200 MHz, DSP CPU2:1200 MHz, DSP CPU3:1200 MHz,
DSP CPU4:1200 MHz, DSP CPU5:1200 MHz,
CCB:666.667 MHz,
DDR:933.333 MHz (1866.667 MT/s data rate) (Asynchronous), IFC:166.667 MHz
CPRI:600 MHz
MAPLE:600 MHz, MAPLE-ULB:800 MHz, MAPLE-eTVPE:1000 MHz
FMAN1: 666.667 MHz
QMAN: 333.333 MHz
Top level changes include:
(1) Top level CONFIG to identify HETEROGENUOUS clusters
(2) CONFIGS for SC3900/DSP components
(3) Global structures like "cpu_type" and "MPC85xx_SYS_INFO"
updated for dsp cores and other components
(3) APIs to get DSP num cores and their Mask like:
cpu_dsp_mask, cpu_num_dspcores etc same as that of PowerPC
(5) Code to fetch and print SC cores and other heterogenous
device's frequencies
(6) README added for the same
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is required at present for device tree control. The ppc4xx does support
GPIOs but does not seem to have a proper driver. So this file is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Era property is added in the crypto node in device tree.
Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to
drivers/sec/sec.c so that it can be used across arm and
powerpc platforms having crypto node.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Fix commit message indentation]
Reviewed-by: York Sun <yorksun@freescale.com>
Some Freescale SoCs like T1020 and T1040 have an integrated
L2 Switch. The L2 Switch ports may be connected to Ethernet PHYs
over SGMII and QSGMII.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The number of supported serdes protocols on Freescale SoCs
has increased over time. Until now, an u64 variable have been
initialized on boot with the configured protocols. However,
since this number has increased (enum srds_prtcl has more
than 64 values), 64 bits are no longer sufficient to hold track
of all the configured protocols.
This patch replaces the u64 map values with static arrays.
To keep track of the number of serdes protocols, the
SERDES_PRCTL_COUNT vale has been added at the end of
enum srds_prtcl. This value must always be the last one.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_PBI_FLASH_BASE is defined for Secure Boot on C29X
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h>.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.
This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL
for mpc85xx platform. A file mpc85xx_gpio.h exists in
arch/powerpc/include/asm. The defintions in that file conflict
with the ones in asm-generic/gpio.h. Hence a dummy header file
has been added. This will be removed after FDT-GPIO stuff is
fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
Newer qoriq socs have an updated dma ip block with a
different compatible. Let's make sure we use the proper
string so that the dmas get their liodn.
In order to have the means to specify the compatible
string, the liodn setting macros were updated to receive
a new parameter for it.
The following SoCs were changed to use the new compatible:
T1023/4, T1040, T2080/1, T4240, B4860.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Commit d6b11fd1 (powerpc: remove MBX and MBX860T boards support)
removed mbxbar field in "struct sysconf512x" by mistake and broke
booting on mpc5121 boards. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
By default, PAMU's (IOMMU) are enabled in case of secure boot.
Disable/bypass them once the control reaches the bootloader.
For non-secure boot, PAMU's are already bypassed in the default
SoC configuration.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.
So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.
The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):
watchdog_period = 1/fTB * 2^x
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resume from deep sleep, uboot needs to enable L2 and CPC
cache, or they would be keeping unusable in kernel because
kernel didn't enble or initialized them.
This patch didn't change the existing L2 cache enabling code,
just put them in a function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.
This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.
This workaround is valid for B4, T4 and T2 platforms, so
added in their config.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4460 differs from B4860 only in number of CPU cores,
hence used existing support for B4860.
B4460 has 2 PPC cores whereas B4860 has 4 PPC cores.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Secure Boot Target is added for T2080RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080RDB.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T1040RDB.h file is removed and a unified file T104xRDB.h is created.
Hence macro CONFIG_T1040 is renamed to CONFIG_T104x.
Signed-off-by: Gaurav Kumar Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode.
In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock
(100MHz) to the following PLLs:
• Platform PLL
• Core PLLs
• USB PLL
• DDR PLL, etc
The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or
DIFF_SYSCLK (differential) is selected as the clock input to the chip.
get_sys_info has been enhanced to add the diff_sysclk so that the
various drivers can be made aware of ths diff sysclk configuration and
act accordingly.
Other changes:
-single_src to ddr_refclk_sel, as it is use for checking ddr reference clock
-Removed the print of single_src from get_sys_info as this will be
-printed whenever somebody calls get_sys_info which is not appropriate.
-Add print of single_src in checkcpu as it is called only once during initialization
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The supplement configuration unit (SCFG) provides chip-specific
configuration and status registers for the device. It is the chip
defined module for extending the device configuration unit (DCFG)
module. It provides a set of CCSR registers in addition to those
available in the device configuration unit.
The base address for this unit is 0x0F_C000.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.
Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.
Signed-off-by: York Sun <yorksun@freescale.com>
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Modify code to adapt to both u-qe and qe.
U_QE is a kind of cutted QE.
the differences between U_QE and QE
1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs.
2. IMMR: have different immr base addr.
3. iopin: U_QE doesn't need to config iopin.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T1040QDS and T1040RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and
CONFIG_T1040RDB
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T2080QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T4240QDS and T4160QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Changes:
1. L2 cache is being invalidated by Boot ROM code for e6500 core.
So removing the invalidation from start.S
2. Clear the LAW and corresponding configuration for CPC. Boot ROM
code uses it as hosekeeping area.
3. For Secure boot, CPC is configured as SRAM and used as house
keeping area. This configuration is to be disabled once in uboot.
Earlier this disabling of CPC as SRAM was happening in cpu_init_r.
As a result cache invalidation function was getting skipped in
case CPC is configured as SRAM.This was causing random crashes.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR, SPI and SD secure boot targets for BSC9132QDS.
Changes:
- Debug TLB entry is not required for Secure Boot Target.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The DDR mapping function really is just a generic virtual -> physical
mapping function. Generalize it so it can support any virtual starting
offset and IO maps just the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.
Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes,
add their defines in arch/powerpc/include/asm/config_mpc85xx.h
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So update acessor functions with common IFC acessor functions to take care
both type of endianness.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE macro for enabling dual
phy in t1040
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040 has only one SerDes block. so update the code accordingly.
Also, add support of SerDes Protocol 0x00, 0x06, 0x40, 0x69 0x85,
0xA7 and 0xAA
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the
32-bit source address specifies the memory address in block address
format. Block length is fixed to 512 bytes as per the SD High Capacity
specification. So we need to convert the block address format
to byte address format to calculate the envaddr.
If there is no enough space for environment variables or envaddr
is larger than 4GiB, we relocate the envaddr to 0x400. The address
relocated is in the front of the first partition that is assigned
for sdboot only.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable Erratum A006379 for T2080, T2081, T4160, B4420.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_FSL_NUM_USB_CTRLS is no longer used,
update it to new CONFIG_USB_MAX_CONTROLLER_COUNT.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Single-source clocking is new feature introduced in T1040.
In this mode, a single differential clock is supplied to the
DIFF_SYSCLK_P/N inputs to the processor, which in turn is
used to supply clocks to the sysclock, ddrclock and usbclock.
So, both ddrclock and syclock are driven by same differential
sysclock in single-source clocking mode whereas in normal clocking
mode, generally separate DDRCLK and SYSCLK pins provides
reference clock for sysclock and ddrclock
DDR_REFCLK_SEL rcw bit is used to determine DDR clock source
-If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in
normal clocking mode by DDR_Reference clock
-If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in
single source clocking mode by DIFF_SYSCLK
Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
The default value of CONFIG_SYS_FSL_TBCLK_DIV is 16.
So, update its value as default.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
The offset of register address within GPIO module is just
CONFIG_SYS_MPC85xx_GPIO_ADDR. So, fix it. The following platforms
are confirmed: MPC8572, P1023, P1020, P1022, P2020, P4080,
P5020, P5040, T4240, B4860.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Update the code that builds the pci endpoint liodn
offset list so that it doesn't overlap with other
liodns and doesn't generate negative offsets like:
fsl,liodn-offset-list = <0 0xffffffcd 0xffffffcf
0xffffffd1 0xffffffd3
0xffffffd5 0xffffffd7
0xffffffd9 0xffffffdb>;
The update consists in adding a parameter to the
function that builds the list to specify the base
liodn.
On PCI v2.4 use the old base = 256 and, on PCI 3.0
where some of the PCIE liodns are larger than 256,
use a base = 1024. The version check is based on
the PCI controller's version register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
T1040 Soc has four personalities:
-T1040 (4 cores with L2 switch)
-T1042:Reduced personality of T1040 without L2 switch
-T1020:Reduced personality of T1040 with less cores(2 cores)
-T1022:Reduced personality of T1040 with 2 cores and without L2 switch
Update defines in arch/powerpc header files, Makefiles and in
driver/net/fm/Makefile to support all T1040 personalities
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefiles]
Acked-by: York Sun <yorksun@freescale.com>
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This allows to share some common code for the boards that use a corenet
base SoC.
Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>
If the DDR3 module supports industrial temperature range and requires
the x2 refresh rate for that temp range, the refresh period must be
3.9us instead of 7.8 us.
This was successfuly tested on kmp204x board with some MT41K128M16 DDR3
RAM chips (no module used, chips directly soldered on board with an SPD
EEPROM).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix minor conflicts in fsl_ddr_dimm_params.h,
lc_common_dimm_params.c, common_timing_params.h]
Acked-by: York Sun <yorksun@freescale.com>
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
CONFIG_USB_MAX_CONTROLLER_COUNT macro recently defined for
initializing all USB controllers on a given platform. This
macro is defined for all 85xx socs
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Previously, the address of a requested capability is define like that
"#define PCI_DCR 0x78"
But, the addresses of capabilities is different with regard to PCIe revs.
So this method is not flexible.
Now a function to get the address of a requested capability is added and used.
It can get the address dynamically by capability ID.
The step of this function:
1. Read Status register in PCIe configuration space to confirm that
Capabilities List is valid.
2. Find the address of Capabilities Pointer Register.
3. Find the address of requested capability from the first capability.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.
Erratum A006379 applies to
T4240 rev 1.0
B4860 rev 1.0, 2.0
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CHASSIS2 architecture never fix clock groups for Cluster and hardware
accelerator like PME, FMA. These are SoC defined. SoC defines :-
- NUM of PLLs present in the system
- Clusters and their Clock group
- hardware accelerator and their clock group
if no clock group, then platform clock divider for FMAN, PME
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
T1040 SoC has
- DDR controller ver 5.0
- 2 PLLs
- 8 IFC Chip select
- FMAN Muram 192K
- No Srio
- Sec controller ver 5.0
- Max CPU update for its personalities
So, update the defines accordingly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
In a very rare condition, a system hang is possible when the e500 core
initiates a guarded load to PCI / PCIe /SRIO performs a coherent write
to memory. Please refer to errata document for more details. This erratum
applies to the following SoCs and their variants, if any.
BSC9132
BSC9131
MPC8536
MPC8544
MPC8548
MPC8569
MPC8572
P1010
P1020
P1021
P1022
P1023
P2020
C29x
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
It is not necessary for all processor to have serdes block 1 & 2.
They may have only one serdes block.
So, put serdes block 1 & 2 related code under defines
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engine. There're
three SoC types(C291, C292, C293) with the following features:
- 512K L2 Cache/SRAM and 512 KB platform SRAM
- DDR3/DDR3L 32bit DDR controller
- One PCI express (x1, x2, x4) Gen 2.0 Controller
- Trust Architecture 2.0
- SEC6.0 engine
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Also change the define name SRDS_RSTCTL_SDPD to
SRDS_RSTCTL_SDEN, which stands for SerDes enable
as mentioned in SerDes module guide
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
Signed-off-by: York Sun <yorksun@freescale.com>
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.
Tested on MT36JSF2G72PZ-1G9E1 RDIMM.
Signed-off-by: York Sun <yorksun@freescale.com>
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.
In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Boot ROM code creates TLB entries for 3.5G space before entering
the u-boot. Earlier we were deleting these entries after early
initialization of CPU. In recent past, code has been added
to invalidate all these entries before relocation of u-boot code.
So this code to delete TLB entries after CPU initialization
is no longer required.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Acked-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.
Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To align with chassis generation 2 spec, all cores are numbered in sequence.
The cores may reside across multiple clusters. Each cluster has zero to four
cores. The first available core is numbered as core 0. The second available
core is numbered as core 1 and so on.
Core clocks are generated by each clusters. To identify the cluster of each
core, topology registers are examined.
Cluster clock registers are reorganized to be easily indexed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis
Generation 2. The major difference between T1040 and its variants is the
number of cores and the number of L2 switch ports.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
