This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.
The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is based on the davinci da850evm. It can boot from either the
on-board 16MB flash or from a microSD card. It also reads board
information from an I2C EEPROM.
The EV3 itself initally boots from write-protected EEPROM, so no
u-boot SPL is needed.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for PMMC the TI power processor on K2G. This processor
manages all power management related activities on the SoC and and
allows the Operating Systems on compute processors such as ARM, DSP to
offload the power logic away into the power processor.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).
The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.
Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.
NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.
This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
The default bootcommand executes x_bootcmd_usb AFTER loading a kernel from
nand and just before executing it, which only slows down boot without adding
any functionality - So drop it.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) prepended mtdparts=
to the flash partition information in CONFIG_MTDPARTS, but it is used like
"mtdparts=" CONFIG_MTDPARTS - So we end up passing mtdparts=mtdparts=.. to
the kernel, confusing the cmdline partition parser.
Fix it by dropping the double 'mtdparts='.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) changed the mtdparts
part of the default environment, but dropped the trailing zero termination -
So the definition of x_bootcmd_kernel becomes part of the x_bootargs
variable.
Fix it by reintroducing the zero termination.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The CONFIG_IPUV3_CLK should be 264000000, to i.MX6DL, it should be
198000000.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Sandor Yu <sandor.yu@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Enable these two filesystems to provide better build coverage in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
It is useful to have sandbox build as much code as possible to avoid having
to build every board to detect build errors. Also we may add tests for some
more partition types at some point.
Enable all partition types in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Enable CONFIG_USB_ETHER_RTL8152 support for Odroid XU4 which
has support for RTL8153-CG gigabit Ethernet adapter,
connected over USB 3.0.
commit 9dc8ba19c5 added support
for Realtek 8152/8153 driver.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CONFIG_MXC_UART_BASE should not be defined in mx7_common.h as
the console port can vary from board to board.
Define CONFIG_MXC_UART_BASE locally instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Select 8-bit BCH ecc-scheme with s/w based error correction
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to booting a zImage kernel by default to align with the other
i.MX boards.
While at it, adjust the fdt_addr so that we can boot a standard
mainline kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a number of AMCC platforms which are close to, or with some
toolchains exceeding, the size constraints. Disable CONFIG_SYS_LONGHELP
to get us room to build with again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Of the several boot devices supported, it looks like the eMMC is the
most commonly used. Enable CONFIG_ENV_IS_IN_MMC by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB. CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the driver in all UniPhier defconfig files and add some
needed defines to the common files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The patch that enabled eSDHC peripheral clock support had an
obvious error as below. This patch is used to fix it.
+#define define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
Fixes: 3285e6cbcc ("powerpc/t2080qds: enable eSDHC peripheral clock support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows all the hush tests implemented in test/py to pass, under qemu
at least.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Scrolling the simple framebuffer is really slow in Raspberry Pi to the
point it delays the boot by a second or two and makes longer output
inconvenient to follow (printenv, md).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Commit 755324 (configs: Use config_distro_defaults.h in ti_armv7_common.h)
made ti_armv7_common.h include config_distro_defaults.h. This breaks the
bootdelay feature in cm_t43 because now the
- #include ti_armv7_common.h (#define CONFIG_BOOTDELAY 1)
- #undef CONFIG_BOOTDELAY
- #include config_distro_defaults.h (#define CONFIG_BOOTDELAY 2)
dance in cm_t43.h is no longer valid and in fact leads to CONFIG_BOOTDELAY
not being defined.
Adapt the config file to the new inclusion hierarchy.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update U-Boot offset and size for raw mmc boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators
are not updated. This is not a problem in cold boot since the default values
that the pmic outputs are correct, but if Linux were to switch the module to a
low power OPP, the new voltage values will be retained after a reboot and the
module will likely hang once U-Boot raises the CPU frequency back up.
Set both CORE and MPU regulators to to 1.1V on boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add full support for SPI flash chips to future-proof U-Boot for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_DM_SERIAL to cm_t43_defconfig. This forces us to update the
CONFIG_SYS_NS16550_REG_SIZE value for SPL.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
spl_board_init() is necessary for boot. Remove the #undef that keeps
it out of the boot sequence.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
bur_am335x_common.h today holds all common configuration which is shared
over all B&R boards.
In future we want to bring up boards which are not based on AM335x only
but we still want to have common configuration over all B&R boards
independent from their architecture.
To prepare this we introduce a new file "bur_cfg_common.h", where we
move all common things, which are not architecture specific, from
bur_am335x_common.h.
On B&R am335x boards we include from now:
#include <configs/bur_cfg_common.h>
#include <configs/bur_am335x_common.h>
On other B&R boards, we include only
#include <configs/bur_cfg_common.h>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
We drop everything possible things from board headerfiles and replace
this functionality with responsible settings in Kconfig (_defconfig).
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
During very early prototype-phase we did boot the AM335x boards
initially from CPSW-EMAC.
Now we don't need this feature anymore.
So we drop it to save MLO-space and having therefore a more quickly
boot.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Logic PD makes four different system on modules. This patch will auto
detect the board type and identify the corresponding device tree image.
V2:
Added 'default:' case to switch statement
Since board_late_init() is defined as int, we now return 0
Signed-off-by: Derald Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the missing CONFIG_BUILD_TARGET to get u-boot-with-spl.sfp built
automatically upon running make in the source tree.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Don't understand how it happened, but this change got applied twice!
Therefore, removing the duplicated items.
Signed-off-by: Steve Rae <srae@broadcom.com>
As tested on the Odroid XU3, large files to be stored on the file system
require considerable time to be physically written to the medium.
The default 300 ms is not enough to store large file (e.g. 26 MiB).
To fix this situation the DFU_MANIFEST_POLL_TIMEOUT has been defined.
It is used to cease the communication with dfu-util and allow the target
board to store the data on file system.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Zybo contains on board HDMI that's why enable EDID.
Doing it via config because zynq i2c driver hasn't been moved to DM yet
and enabling via Kconfig requires DM_I2C.
This will be moved that driver is moved to DM.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the miss-placed \0 and add missing ; for usbboot env variable.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove CONFIG_ZYNQ_BOOT_FREEBSD configuration option and setup
CONFIG_SYS_MMC_MAX_DEVICE 1 for all Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Introduce macros and command to support booting M4 core for
i.MX7D SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce macros and command to support booting M4 core for
i.MX6SX SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Select CONFIG_FSL_QSPI so that the SPI can be probed:
=> sf probe
SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
New features for smartweb:
* switch to hush command parser
* change autoboot stop to <ESC><ESC>
* allow to write ethaddr
Signed-off-by: Matthias Michel <matthias.michel@siemens.com>
Reviewed-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This allows U-Boot to expose UMS and DFU protocols on this port in device
mode, or to act as a USB host on the port, using an "OTG" (micro-B to
female A host) cable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option is no longer used now that DM_USB is enabled.
Fixes: 534f9d3fef ("dm: tegra: usb: Move USB to driver model")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While we transition to using driver model for video, we need to support both
options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The kernel gets much too sad when the ramdisk is loaded too high into the 1GiB
of memory on Raspberry Pi 2:
## Flattened Device Tree blob at 00000100
Booting using the fdt blob at 0x000100
Loading Ramdisk to 39c14000, end 3ab45067 ... OK
Using Device Tree in place at 00000100, end 000045ea
...
[ 0.599346] Unpacking initramfs...
[ 0.602924] Unable to handle kernel paging request at virtual address f9c14000
Placement of the device tree was fixed in 89ca1000 (ARM: rpi: set fdt_high
in the default environment).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
With the recent addition of UBI support, this patch will add the preset
parameters to allow for mouting an UBIFS from the 'fs' partition in NAND.
-V2: ubi.mtd=fs instead of ubi.mtd=4
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SF_DEFAULT_MODE is used to select default SPI mode when using
sf commands. Therefore fix am43xx to use CONFIG_SF_DEFAULT_MODE instead
of CONFIG_DEFAULT_SPI_MODE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Based on the work done by Overo, this seems to help some compilers
that have a hard time fitting all the code into the allocated space.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Boot with the Linux zImage and am3517-evm.dtb pair, when SD/MMC media
is present. This behavior can be overridden by creating a 'uEnv.txt'
file with 'uenvcmd' defined.
To boot an existing 'uImage', create the following 'uEnv.txt':
[start]-----------------------------------------------------------------
loaduimage=fatload mmc 0:1 ${loadaddr} ${bootfile}
uenvcmd=run loaduimage; run mmcargs; bootm ${loadaddr}
[end]-------------------------------------------------------------------
Inspired by similar patches, for other OMAP3 boards, from EEWiki
- https://github.com/eewiki/u-boot-patches/tree/master/v2016.01
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This environment define has been here to work around the LMB
allocation error introduced by commit 9c11135ce0 ("image: fix
getenv_bootm_size() function").
It is no longer needed because the root cause was fixed by commit
0cb389dd1a ("image: fix getenv_bootm_size() function again").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No special reason for the current stack address 0x0ff08000.
Change it to 0x00100000 to simplify the init_page_table.
There are two types of SoCs in terms of the load address of SPL.
[1] PH1-sLD3, PH1-LD4, PH1-sLD8
SPL is loaded at 0x00040000-0x0004ffff
[2] PH1-Pro4, PH1-Pro5, ProXstream2, PH1-LD6b
SPL is loaded at 0x00100000-0x0010ffff
The new stack area (0x000f8000-0x00100000) should be safe for all the
cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit ad1ecd2063 ("fdt: Build a U-Boot binary without device
tree") and commit 03c25bcd26 ("fdt: Build an SPL binary without
device tree"), we can use shorter file names for the output images.
The default configuration for UniPhier SoCs enables CONFIG_OF_SEPARATE
and CONFIG_SPL_OF_CONTROL. In this case, spl/u-boot-spl.bin is the
same as spl/u-boot-spl-dtb.bin. Likewise, u-boot.img is the same as
as u-boot-dtb.img. So, this change of the flow has no impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The environment "bootm_low" is updated before the "bootz" command.
This is common for all the boot modes (NOR, NAND, TFTP, etc.), so
can be factored out.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 25d4eb8091 ("ARM: uniphier: add bootm_low environment")
missed to add "bootm_low" for FIT boot. Set "bootm_low" to the
DRAM base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 89835b3557 ("ARM: uniphier: allow to run zImage rather than
uImage") changed the kernel boot commands. Unlike "bootm", "bootz"
does not relocate the kernel image. When the boot device is a NOR
flash, the zImage should be copied from the NOR onto the DRAM before
it is passed to the "bootz" command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
There are various different boards with the same hardware sold as LG Optimus
Black, such as P970, P970g and KU5900. Since this port is functional for all
variants, it doesn't make sense to keep references to P970.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ARM Linux kernel requires the DT to be in memory accessible early
during the boot process. This always happens naturally on the RPi 1,
since the maximum memory size of 512MiB, and additionally some of that
is reserved for use by the GPU. The RPi 2 has 1GiB of RAM (minus some
GPU usage), and so if the DT is relocated to the top of RAM, Linux cannot
access it. Prevent this from happening by setting fdt_high.
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Update rpi-common.h's documentation that describes the rationale for
choosing various addresses for standardized variables used by boot
scripts. This comment was correct when written, but not updated when some
of the values were changed.
Fixes: 14006a5671 ("rpi: set fdt_addr_r to 0x00000100 to match default
...device_tree_address")
Cc: Jonathan Liu <net147@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
UBIFS is the preferred FS, and YAFFS isn't officially included in
Linux. Removing this feature reduces the code size.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The interface automatically converts one 32-bit word into two 16 words.
The README said it is permissible to use this flag in that scenario.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Previously, Omap3_logic assumed X-loader was present. With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot. This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Now that the RTL8169 driver warning is fixed we can drop this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It does not build if without CONFIG_DM_PCI_COMPAT. For now we just
disable it, until some day we add USB support to EFI application.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some #undef from efi-x86.h to efi-x86_defconfig as these are
already Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Without this CONFIG_BOOTDELAY, autobooting does not work at all. As
autoboot_command() from common/* will not get called. So lets define
CONFIG_BOOTDELAY, so that auto-booting works on x86.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miao Yan <yanmiaobest@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Miao Yan <yanmiaobest@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Remove the legacy way of enabling GPIO, SPI and UART on Vybrid
based boards since these driver's now only supports DT mode.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1
port, enable this display feature by adding relevant BSP codes
and configurations.
Signed-off-by: Ye Li <ye.li@nxp.com>
As mx6slevk has only one Ethernet port, we don't need
to declare CONFIG_ETHPRIME, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
All boards that support PXE booting use the pxefile_addr_r variable. Standardise
wandboard with this variable as pxe_addr_r isn't used anywhere else so it's a
typo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This adds ethernet, TFTP support for PIC32MZ[DA] Starter Kit. Also
custom environment variables/scripts are added to help boot from network.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Enable MMC, SDHCI, FAT_FS support for PIC32MZ[DA] StarterKit.
Also add custom scripts, rules to boot Linux from microSD card.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This adds support for Microchip PIC32MZ[DA] StarterKit board
based on a PIC32MZ[DA] family of microcontroller.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Increase the kernel size supported for LS1021A platform. Define
CONFIG_SYS_BOOTM_LEN to 64M.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
kernel_size env variable is defined as 0x28000000, it is beyond NOR
flash range. Update kernel_size with 40MB kernel size.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On Novena, the DRAM SPD is connected to i2c1 while the Utility EEPROM
is connected to i2c3. Now that the EEPROM handling in U-Boot is fixed,
also fix this bit on Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Stefano Babic <sbabic@denx.de>
Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds the generic FS commands (ls, load) to all x86 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miao Yan <yanmiaobest@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add lpuart support using the driver model.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The file fsl_secure_boot.h must be included in config file for
Secure Boot. This is not required to be protected by any macro.
CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be
turned on.
The above was missing in some config files and all files have been
made uniform in this respect.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Define auto negotiation timeout as 20secs
the default 4secs might not be sufficient
always and hence defined for worst case.
It is observed that autoneg takes moretime
if connected to outside network and hence
increase it to 20secs.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont use shortcut command for setenv as
it wont work now due introduction of new
command setexpr.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify DFU commands to use latest kernel offsets and sizes
as per modified partitions in the linux device tree.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs from EL3 system timer is setup based on this macro.
Software default freq for silicon is 100MHz but enable opton to rewrite
it. Emulation platform is using 4MHz.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected
U-Boot using sdboot1 variable which refers to mmc dev 1.
But this device doesn't exist because only one controller is available.
This patch fix logic around sdboot mode with using sdbootdev internal
variable.
Reported-by: Chris Kohn <ckohn@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link to zynqmp common file is incorrect. Fix it by removing the whole
link because it is visible from the file where to look at it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define minimum sdhci frequency for ep, as not defining
it causes the divisor to be 2048 as per sd version but
keeping clock very low on ep causes command failures.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To solve enabling ETH_DM where ksz90x1_reg_field is defined only when
additional Micrel type is defined.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc405 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc440 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale's management complex (MC) uses System DDR for internal usage.
Increase used System DDR size from 256MB to 512 MB.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch also exposes the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since we are manipulating GPIO 189 to determine the board type, we
need to enable the GPIO Bank 6.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not undefine CONFIG_BOOTDELAY, so board can boot without user
intervention.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This commit 4bdcbe60a1 removes reset_cpu
which breaks SPL build when DEBUG macro defined.
"
arch/arm/lib/built-in.o: In function `do_reset':
~/uboot/arch/arm/lib/reset.c:45: undefined reference to `reset_cpu'
scripts/Makefile.spl:244: recipe for target 'spl/u-boot-spl' failed
"
Enable CONFIG_SPL_WATCHDOG_SUPPORT to fix this issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Eric Nelson <eric@nelint.com>
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Support uncompressing zImage which is larger than 8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
To i.MX6UL 14x14 EVK, system memory is 512M; to i.MX6UL 9x9 EVK,
system memory is 256M. If setting mtest size to 256M, mtest will
crash uboot for i.MX6UL 9x9 evk. So change mtest size to 128M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
At present interrupt routing is set up from arch_misc_init(). We can do it
a little later instead, in interrupt_init().
This removes the manual pirq_init() call. Where the platform does not have
an interrupt router defined in its device tree, no error is generated. Some
platforms do not have this.
Drop pirq_init() since it is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that the DWC2 driver supports split transactions, we can reasonably
enable support for USB keyboards. This wasn't terribly useful before
since keyboards are usually LS/FS devices, and thus require split
transaction support when attached to a USB hub such as the hub built into
the RPi model Bs.
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable these devices using the VOPL video output device. We explicitly
disable VOPB in the device tree to avoid it taking over. Since this device
has an LCD display this comes up by default. If the display fails for some
reason then it will attempt to use HDMI. It is possible to force it to fail
(and thus fall back to HDMI) by puting 'return -EPERM' at the top of
rk_edp_probe(). For now there is no easy way to select between the two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the low-level init is skipped on rockchip. Among other things
this means that the instruction cache is left disabled. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We must use the console name in the 'stdout' variable to select the one
we want. At present the name is formed from the driver name with a suffix
indicating the rotation value.
It seems better to name them sequentially since this can be controlled by
driver order. So adjust the code to use 'vidconsole' for the first,
'vidconsole1' for the second, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
To reduce the SPL image size, drop the LED features. Jerry does not have
an LED and we can leave out GPIO support also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is defined in the device tree in Linux. Copy over the settings so that
this can be used instead of hard-coding the reset line.
Signed-off-by: Simon Glass <sjg@chromium.org>
There's a 64K reserved area at the end of the first 4M.
Store env there, so we can use fastboot to flash it.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
We will save boot mode flag in grf's os_reg[4], if fastboot
requested or fastboot key pressed, try to enter fastboot mode
at preboot stage.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a test for the 'bmp' command. Test both the uncompressed and compressed
versions of the file, since they use different code paths.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Move this option to Kconfig. This is quite simple as only sandbox uses the
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert ls1021atwr_nor to driver model support. As a start, enable
ns16550 serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The iocon and bamboo boards are often on the verge of, or going over,
their allowed size limits depending on toolchain used. If we turn off
CONFIG_SYS_LONGHELP we can gain approximately 14KiB back.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The patch removes some macros that are not used.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Symbol is already defined in ti_armv7_common.h which is included
via ti_armv7_omap.h
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can delete board/pb1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/dbau1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/micronas/vct/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The board/freescale/m54418twr/config.mk defined TEXT_BASE, which has
the same value as CONFIG_SYS_TEXT_BASE. The TEXT_BASE is referenced
by two files:
- arch/m68k/cpu/mcf5445x/start.S and include/
- include/configs/M54418TWR.h
Replace the references with CONFIG_SYS_TEXT_BASE and delete
board/freescale/m54418twr/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
The load address of the kernel can be changed via "kernel_addr_r"
environment. The device tree and the initramdisk should be relocated
according to the kernel location.
The "bootm_low" should be calculated by masking the lower bits
(TEXT_OFFSET part) of the "kernel_addr_r" environment value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot relocates the device tree and the initramdisk to the tail
of the memory region before booting the kernel.
Some UniPhier boards are equipped with a large amount of memory.
For those boards, the device tree and the initramdisk are placed out
of the the kernel causing a kernel panic.
Add CONFIG_SYS_BOOTMAPSZ to prevent them from going too high.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
config.h is used in target and host code and therefore should not
pull in target header files to avoid compile errors. This change
is also required for the MIPS header file sync done in follow-up
patches.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds intermediate kconfig symbols which select their SoC
family. Boards then select them instead of the family symbol directly.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
Th cache command can be useful sometimes. So lets enable it on the
AXP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds the common FS options to the Marvell AXP eval board. This
includes EXT2, EXT4, FAT and VFAT. And of course the generic FS commands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Enable the newly introduced SATA driver for the Marvell AXP with DMA
support instead of the PIO-only IDE driver. This increases the
transfer speed. And is also more in-line with the Armada 38x
ports, which also use a SATA driver (AHCI) and the "sata" U-Boot
commands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This adds various env settings for more flexible boot possibilities, including
devicetree support and distro defaults config.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change updates DevKit3250 board powerd by NXP LPC3250 SoC:
* due to increased resulting U-boot image size give more space to
store loaded and relocated versions,
* add DMA support, which is used by NAND SLC driver,
* add NXP OHCI and PHY drivers to the image,
* add USB, JFFS and FAT commands.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Based on the am335x_evm conversion, switch to config_distro_bootcmd for
mmc and pxe. Tested with Fedora 23.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that ti_armv7_common.h uses config_distro_defaults.h we don't need
to include it again and then undef CONFIG_BOOTDELAY
Signed-off-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
DM_SPI and DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since OMAP's spl doesn't support DM currently, do not define DM_SPI and
DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This feature is required in SPL to enable support for loading from SPI
flash.
Also clean up the #define in socfpga_common.h.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
By default, ramdisk load address is defined to 02000000 in env string.
When loading bzImage to 01000000 (default address), there's a chance that
the ramdisk header would be overwritten by the kernel. Thus increase the
gap and make ramdisk load at 04000000 by default and also this patch
introduces a new configuration item CONFIG_RAMDISK_ADDR for this purpose
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rather than using a new debug UART implementation, use the standard one
provided by U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
If CONFIG_SYS_STDIO_DEREGISTER is not enabled, usb reset
will fail every time. Enabling it allows usb reset to
work.
Signed-off-by: Andy Fleming <afleming@gmail.com>
The default kernel load offset for an arm64 kernel is 0x80000, so
U-Boot takes cares of moving the loaded kernel to a matching memory
location just before booting it.
Since we run with caches off, this takes a while for any decently
sized kernel - with no output explaining the reason for the delay
(unless one uses a DEBUG build).
By adjusting the default load offset for Juno and VFP to be 512K
aligned in the first place we can skip this copying and boot much
faster.
Tested on Juno.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Various updates did not make it through to this board. Also the instructions
for building a SPI image are no-longer correct. Fix these so that Jerry can
boot to a prompt again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add common configuration bits for the Denali NAND controller and also
support for using it as a boot device in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
It is not possible to compile DFU MMC support if the MMC support is not
compiled into U-Boot. Secure the code with an ifdef to prevent compiler
splat.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
It is not possible to compile MMC/SPI SPL if the respective DM_MMC/DM_SPI
bits are not enabled. Secure the code with an ifdef to prevent compiler
splat.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling qspiload command which will load the kernel
image and dtb from UBIFS within MTD partition labeled
UBI.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling qspiload command which will load the kernel
image and dtb from UBIFS within MTD partition labeled
UBI.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling qspiload command which will load the kernel
image and dtb from UBIFS within MTD partition labeled
UBI.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling qspiload command which will load the kernel
image and dtb from UBIFS within MTD partition labeled
UBI.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
When QSPI and NAND is enabled, the ubi and ubifs support
will be enabled too.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
UniPhier SoC family adopt ARM Multi-platform in Linux since the first
upstreaming. Because CONFIG_ARM_PATCH_PHYS_VIRT is defined, the
kernel image is completely position-independent. There is no reason
to decide the load address on compile time, but it is up to the boot
loader. Now, zImage is handier than uImage, also it allows to skip
the relocation of the kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now this environment is run-time set to the DTB name U-Boot is really
running with. Drop the static define.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
