In ARMv8 we have the choice between two stack pointers to use: SP_EL0 or
SP_ELx, which is banked per exception level. This choice is stored in
the SP field of PState, and can be read and set via the SPSel special
register. When the CPU takes an exception, it automatically switches to
the SP_ELx stack pointer.
Trusted Firmware enters U-Boot typically with SPSel set to 1, so we use
SP_ELx all along as our sole stack pointer, both for normal operation and
for exceptions.
But if we now for some reason enter U-Boot with SPSel cleared, we will
setup and use SP_EL0, which is fine, but leaves SP_ELx uninitialised.
When we now take an exception, we try to save the GPRs to some undefined
location, which will usually end badly.
To make sure we always have SP_ELx pointing to some memory, set SPSel
to 1 in the early boot code, to ensure safe operation at all times.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv8 architecture describes the "SError interrupt" as the fourth
kind of exception, next to synchronous exceptions, IRQs, and FIQs.
Those SErrors signal exceptional conditions from which the system might
not easily recover, and are normally generated by the interconnect as a
response to some bus error. A typical situation is access to a
non-existing memory address or device, but it might be deliberately
triggered by a device as well.
The SError interrupt replaces the Armv7 asynchronous abort.
Trusted Firmware enters U-Boot (BL33) typically with SErrors masked,
and we never enable them. However any SError condition still triggers
the SError interrupt, and this condition stays pending, it just won't be
handled. If now later on the Linux kernel unmasks the "A" bit in PState,
it will immediately take the exception, leading to a kernel crash.
This leaves many people scratching their head about the reason for
this, and leads to long debug sessions, possibly looking at the wrong
places (the kernel, but not U-Boot).
To avoid the situation, just unmask SErrors early in the ARMv8 boot
process, so that the U-Boot exception handlers reports them in a timely
manner. As SErrors are typically asynchronous, the register dump does
not need to point at the actual culprit, but it should happen very
shortly after the condition.
For those exceptions to be taken, we also need to route them to EL2,
if U-Boot is running in this exception level.
This removes the respective code snippet from the Freescale lowlevel
routine, as this is now handled in generic ARMv8 code.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With the current configuration provided in mxsimage{-spl}.mx28.cfg the
size of SPL binary has been constrained to 32 KiB, due to "LOAD IVT"
command with 0x8000 offset.
The problem was that, the imx28 ROM takes the u-boot.sb and then
extracts from it the IVT header and places it on the 0x8000 OCRAM offset
overwriting any valid (i.e. loaded from eMMC or SPI-NOR) SPL code. This
bug was unnoticed as the overwrite size was just 32 bytes, so the
probability that some important code is altered was low.
However, in the XEA board (where the SPL size is ~39KiB), the overwritten
data was `(struct dm_spi_ops *) 0x800c <mxs_spi_ops>`, which is used
during the boot process.
As a result the SPL execution code hanged with "undefined instruction"
abort as callbacks (with wrong addresses) from it were called.
The fix is to change the OCRAM's offset where IVT is loaded to 0xE000,
so the SPL can grow up to ~57KiB (the maximal size of OCRAM memory
available is 0xE3FC).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The imx28 uses following voltage supplies hierarchy:
VDD_5V (VDD_BAT) -> VDDIO -> VDDA -> VDDMEM
\-----> VDDD
One shall first enable DCDC on the parent source (VDDIO) and then
follow with its children.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Some Allwinner SoCs use ARM926EJ-S core.
Add Allwinner/sunXi specific code to ARM926EJ-S CPU dircetory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both armv7 and arm926ejs use this timer code so move it to mach-sunxi.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv7 start code has support for saving some boot params at the
entry point, which is used by some SoCs to return to BROM.
Port this to ARM926EJ-S start code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.
The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is some code that tries to "reset" the SCTLR_ELx register early in
the boot process. The idea seems to be to guarantee some sane settings
that U-Boot actually relies on, for instance running in little-endian
mode, with the MMU off initially.
However the current code has multiple problems:
- For a start, no platform or config defines the symbol that would
enable that code.
- The code itself really only works if the bits that it tries to clear
are already cleared:
- If we run in big-endian mode initially, any previous loads would have
been wrong already. That applies to the (optional) relocation code,
but more prominently to the mask that it uses to clear those bits:
"ldr x1, =0xfdfffffa" looks innocent, but actually involves a memory
access to the literal pool, using the current endianness.
- If we run with the MMU enabled, we are probably doomed already. We
*could* hope that we are running with an identity mapping, but would
need to do some cache maintenance to avoid losing dirty cache lines.
- The idea of doing a read-modify-write of SCTLR is somewhat
questionable to begin with, because as the owner of the current
exception level we should initialise all bits of this register with a
certain fixed value.
- The code is unnecessarily complicated, and the function name is
misspelled.
While those problems *could* admittedly be fixed, the point that is does
not seem to be used at all at the moment tells me we should just remove
this code, and be it to not give a bad example.
If people care, I could introduce some proper SCTLR initialisation code.
We are about to work this out for the boot-wrapper[1] as we speak, but
apparently we got away without doing this in U-Boot ever since, so it
might not be worth the potential trouble.
[1] https://lore.kernel.org/linux-arm-kernel/20220114105653.3003399-7-mark.rutland@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Setting LINUX_KERNEL_IMAGE_HEADER=y attempts to include an ARM64 Linux
kernel image header at the start of both U-Boot proper and SPL binaries.
However, some definitions that the image header uses are not included by
the SPL linker script, resulting in a build error. Include them the way
they are included in U-Boot proper's linker script to fix the error.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Apple's ARMv8 cores don't implement EL3 and therefore don't
provide a PSCI implementation. So don't attempt to use
PSCI to reset on machines using Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Don't use efi_allocate_pages(). The allocated memory isn't carved out of
the lmb allocations. The memory might then be allocated twice.
Particulary, this might happened with the fdt_high/initrd_high feature
which will relocate the fdt/ramdisk. This might then overlap with the
spin table.
Instead use memalign() which allocates on memory on the heap which is
correctly carved out by lmb.
Please note, that the memory is later reserved in the device tree as
well as in the EFI memory map in ft_fixup_cpu() (in
arch/arm/cpu/armv8/fsl-layerscape/fdt.c).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Instead of looking at all USB (host) devices, just search all DWC3
device tree nodes. This will (1) fix a panic if of_match is zero and (2)
also apply the fixup if the controller is in peripheral mode. Both
happen when the DWC3 USB controller driver is used.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no "fsl,ls1028a-gpu" compatible string. It is solely for the
proprietary driver which will never be open source. Lately, linux gained
support for the open source etnaviv driver for the GPU (although there
is still support for the DisplayPort PHY missing to get actual graphics
output). Thus, instead of supporting some proprietary driver, switch
over to the open source one, which also have an official device tree
binding.
Cc: Andy Tang <andy.tang@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Disabling PCIE support currently lead to a crash because the code for
erratum A010315 is still run. Add a conditional to only select
CONFIG_SYS_FSL_ERRATUM_A010315 when CONFIG_PCIE_LAYERSCAPE is enabled.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Ad-hoc bindings that are not part of the upstream device tree / bindings
are not allowed in-tree. Only bindings that are in-progress with
upstream and then re-synced once agreed upon are.
This reverts commit af288cb291.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reserved memory nodes can have additional flags. Support reading and
writing these flags to ensure that reserved memory nodes can be properly
parsed and emitted.
This converts support for the existing "no-map" flag to avoid extending
the argument list for fdtdec_add_reserved_memory() to excessive length.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reserved memory nodes can have a compatible string list to identify the
type of reserved memory that they represent. Support specifying an
optional compatible string list when creating these nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the following STV0991 specific configs:
- CONFIG_STV0991 (never used, only defined in CONFIG_SYS_EXTRA_OPTIONS)
- CONFIG_STV0991_HZ (replaced by generic CONFIG_SYS_HZ)
- CONFIG_STV0991_HZ_CLOCK (replaced by generic CONFIG_SYS_HZ_CLOCK)
This patch allows to reduce the file config_whitelist.txt.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Replace the current 2-instruction 2-step tripling code by a
corresponding single instruction leveraging ARMv8-A's "flexible second
operand as a register with optional shift". This has the added benefit
(albeit arguably negligible) of reducing the final code size.
Fix the comment as the tripled cache level is placed in x12, not x0.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Improve the file's readability and conciseness by using the appropriate
Aarch64 instruction: ubfx (unsigned bitfield extract). This makes the
code easier to follow as it directly manipulates the offsets and widths
of the fields read from system registers, as they are expressed in the
Standard (ARM ARM). This has the added benefit (albeit arguably
negligible) of reducing the final code size.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
The AT91 RM9200DK board was removed long time ago.
Remove existing references that were not cleaned up.
Fixes: 1c85752258 ("ARM: remove broken "at91rm9200dk" board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
Armv8r64 is the first Armv8 platform that only has a PMSA at the
current exception level. The architecture supplement for Armv8r64
describes new fields in ID_AA64MMFR0_EL1 which can be used to detect
whether a VMSA or PMSA is present. These fields are RES0 on Armv8a.
Add logic to read these fields and, for the protection of the memory
used by U-Boot, initialize the MPU instead of the MMU during init, then
clear the MPU regions before transition to the next stage.
Provide a default (blank) MPU memory map, which can be overridden by
board configurations.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The use of ARMv8.3 pointer authentication (PAuth) is governed by fields
in HCR_EL2, which trigger a 'trap to EL2' if not enabled. The reset
value of these fields is 'architecturally unknown' so we must ensure
that the fields are enabled (to disable the traps) if we are entering
the kernel at EL1.
The APK field disables PAuth instruction traps and the API field
disables PAuth register traps
Add code to disable the traps in armv8_switch_to_el1_m. Prior to doing
so, it checks fields in the ID_AA64ISAR1_EL1 register to ensure pointer
authentication is supported by the hardware.
The runtime checks require a second temporary register, so add this to
the EL1 transition macro signature and update 2 call sites.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
A U-Boot image could be loaded and executed at a different
location than it was linked at.
For example, Aspeed takes a stable release version of U-Boot image
as the golden one for recovery purposes. When the primary storage
such as flash is corrupted, the golden image would be loaded to any
SRAM/DRAM address on demands through ethernet/UART/etc and run for
rescue.
To deal with this condition, the PIE is needed as there is only one
signed, golden image, which could be however executed at different
places.
This patch adds the PIE support for ARMv7 platform.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC
related registers that need to be handled more cleanly but start by
moving this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
NXP platforms expect custom bootcmd and mcinitcmd to be
updated as per boot source with default environment.
Check env variable fsl_bootcmd_mcinitcmd_set to prepare
bootcmd and mcinitcmd
Fixes: cbf77d2018 (armv8: fsl-layerscape: Fix automatic
setting of bootmcd with TF-A)
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This symbol was largely migrated, except for one case. Update it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At early U-Boot stage, before relocation, MMU is not yet configured
and disabled. DDR may not be configured with the correct memory
attributes (can be configured in MT_DEVICE instead of MT_MEMORY).
In this case, usage of memcpy_{from, to}io() may leads to synchronous
abort in AARCH64 in case the normal memory address is not 64Bits aligned.
To avoid such situation, forbid usage of normal memory cast to (u64 *) in
case MMU is not enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: mark.kettenis@xs4all.nl
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
CNTFRQ_EL0 is only writable from the highest supported exception
level on the platform. For Armv8-A, this is typically EL3, but
technically EL2 and EL3 are optional so it may need to be
initialized at EL2 or EL1. For Armv8-R, the highest exception
level is always EL2.
This patch moves the initialization outside of the switch_el
block and uses a new macro branch_if_not_highest_el which
dynamically detects whether it is at the highest supported
exception level.
Linux's docs state that CNTFRQ_EL0 should be initialized by the
bootloader. If not set, the the U-Boot prompt countdown hangs.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
As seen with clang-12:
warning: __asm_invalidate_l3_dcache changed binding to STB_WEAK
As we indeed use ENTRY and then declare the function weak manually. Use
the WEAK declarative from <linux/linkage.h> instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Marc Zyngier <maz@kernel.org>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for 1.3GHz, 1.35GHz and 1.4GHz parts. This is based on
equivalent code in Broadcom's LDK 5.0.6.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Change the USB erratum number A-050106 to A-050204 as A-050106 is
a duplicate and never be published.
Fixes 0cfa00cdb9 (“armv8: Add workaround for USB erratum A-050106”)
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
For some reason when building SPL for ARMv8 with LTO, the relocation
information is not discarded.
Discard it explicitly in the linker script.
This fixes LTO build for imx8mm_venice_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building with LTO, the compiler complains about type mismatch of
function clk_bsc_enable() in file:
arch/arm/cpu/armv7/kona-common/clk-stubs.c
vs other files that define or use this function:
warning: type of ‘clk_bsc_enable’ does not match original declaration.
Change the type of this function to that of the other usages.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When imx28_xea_defconfig is built with LTO, the compiler complains about
the two different declarations of _start:
include/asm-generic/sections.h as extern void _start(void);
arch/arm/cpu/arm926ejs/mxs/mxs.c as extern uint32_t _start;
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix LTO build for some thumb-interwork usecases (such as for
da850evm_defconfig), where inline assmebly such as
mrc p15,0,r2,c1,c0,0
causes the compiler to fail during LTO linking with
Error: selected processor does not support `mrc p15,0,r2,c1,c0,0'
in Thumb mode
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
On ARM, the gd pointer is stored in registers r9 / x18. For this the
-ffixed-r9 / -ffixed-x18 flag is used when compiling, but using global
register variables causes errors when building with LTO, and these
errors are very difficult to overcome.
Richard Biener says [1]:
Note that global register vars shouldn't be used with LTO and if they
are restricted to just a few compilation units the recommended fix is
to build those CUs without -flto.
We cannot do this for U-Boot since all CUs use -ffixed-reg flag.
It seems that with LTO we could in fact store the gd pointer differently
and gain performance or size benefit by allowing the compiler to use
r9 / x18. But this would need more work.
So for now, when building with LTO, go the clang way, and instead of
declaring gd a global register variable, we make it a function call via
macro.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=68384
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
DM_SERIAL needs both the device tree as well as an early heap. Thus, we
have to call spl_early_init() to initialize the memory allocator and the
setup the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
To use the debug UART we have to call debug_uart_init() in the SPL. Do
so as soon as possible.
As an example, here is how you can use it on a LS1028A SoC:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_BASE=0x21c0500
CONFIG_DEBUG_UART_CLOCK=200000000
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Several architectures had a default board_fit_config_name_match already;
this provides a generic weak version. We default to rejecting all configs.
This will use the FIT's default config, instead of the first config. This
may result in boot failures if there are multiple configurations and the
first config is *not* the default.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.
Signed-off-by: Michael Walle <michael@walle.cc>
