Commit graph

708 commits

Author SHA1 Message Date
York Sun
123922b1e5 powerpc/mpc8xxx: Fix DDR driver handling quad-rank DIMMs and address calculation
Fix handling quad-rank DIMMs in a system with two DIMM slots and first
slot supports both dual-rank DIMM and quad-rank DIMM.

For systems with quad-rank DIMM and double dual-rank DIMMs, cs_config
registers need to be enabled to maintain proper ODT operation. The
inactive CS should have bnds registers cleared.

Fix the turnaround timing for systems with all chip-selects enabled. This
wasn't an issue before because DDR was running lower than 1600MT/s with
this interleaving mode.

Fix DDR address calculation. It wasn't an issue until we have multiple
controllers with each more than 4GB and interleaving is disabled.

It also fixes the message of DDR: 2 GiB (DDR3, 64-bit, CL=0.5, ECC off)
when debugging DDR and first DDR controller is disabled. With the fix,
the first enabled controller information will be displayed.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:26 -05:00
York Sun
57495e4e5e powerpc/mpc8xxx: Update DDR registers
DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.

CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
	000 -> Termsel off
	001 -> 120 Ohm
	010 -> 180 Ohm
	011 -> 75 Ohm
	100 -> 110 Ohm
	101 -> 60 Ohm
	110 -> 70 Ohm
	111 -> 47 Ohm

Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.

Extend DDR register timing_cfg_1 to have 4 bits for each field.

DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:26 -05:00
Roy Zang
111fd19e3b fm/mEMAC: add mEMAC frame work
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.

Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:25 -05:00
York Sun
d2404141f9 powerpc/mpc85xx: Add B4860 and variant SoCs
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):

Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
    clusters-each core runs up to 1.2 GHz, with an architecture highly
    optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
    cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
    each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
    including Turbo or Viterbi decoding, Turbo encoding and rate matching,
    MIMO MMSE equalization scheme, matrix operations, CRC insertion and
    check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
    and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
    the e6500 cores, SC3900 FVP cores, memories and external interfaces.
    CoreNet fabric interconnect runs at 667 MHz and supports coherent and
    non-coherent out of order transactions with prioritization and
    bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
  Frame Manager (FMan), which supports in-line packet parsing and general
    classification to enable policing and QoS-based packet distribution
  Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
    of queue management, task management, load distribution, flow ordering,
    buffer management, and allocation tasks from the cores
  Security engine (SEC 5.3)-crypto-acceleration for protocols such as
    IPsec, SSL, and 802.16
  RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
    outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
    bandwidth saving and high utilization of processor elements. The
    9856-Kbyte internal memory space includes the following:
  32 Kbyte L1 ICache per e6500/SC3900 core
  32 Kbyte L1 DCache per e6500/SC3900 core
  2048 Kbyte unified L2 cache for each SC3900 FVP cluster
  2048 Kbyte unified L2 cache for the e6500 cluster
  Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
  Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
    of up to 8 lanes
  Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
    less antenna connection
  Two 10-Gbit Ethernet controllers (10GEC)
  Six 1G/2.5-Gbit Ethernet controllers for network communications
  PCI Express controller
  Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:24 -05:00
York Sun
9e75875849 powerpc/mpc85xx: Add T4240 SoC
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):

12 dual-threaded e6500 cores built on Power Architecture® technology
  Arranged as clusters of four cores sharing a 2 MB L2 cache.
  Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
    v2.06-compliant)
  Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
  CoreNet fabric supporting coherent and non-coherent transactions with
    prioritization and bandwidth allocation amongst CoreNet end-points
  1.6 Tbps coherent read bandwidth
  Queue Manager (QMan) fabric supporting packet-level queue management and
    quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
    support
  Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
    the following functions:
  Packet parsing, classification, and distribution (Frame Manager 1.1)
  Queue management for scheduling, packet sequencing, and congestion
    management (Queue Manager 1.1)
  Hardware buffer management for buffer allocation and de-allocation
    (BMan 1.1)
  Cryptography acceleration (SEC 5.0) at up to 40 Gbps
  RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
  Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
  DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
  Up to four 10 Gbps Ethernet MACs
  Up to sixteen 1 Gbps Ethernet MACs
  Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
  Four PCI Express 2.0/3.0 controllers
  Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
    Type 11 messaging and Type 9 data streaming support
  Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
  Two serial ATA (SATA 2.0) controllers
  Two high-speed USB 2.0 controllers with integrated PHY
  Enhanced secure digital host controller (SD/MMC/eMMC)
  Enhanced serial peripheral interface (eSPI)
  Four I2C controllers
  Four 2-pin or two 4-pin UARTs
  Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:23 -05:00
Andy Fleming
f311838ded powerpc/mpc85xx: Add T4 device definitions
The T4 has added devices to previous corenet implementations:

* SEC has 3 more DECO units
* New PMAN device
* New DCE device

This doesn't add full support for the new devices. Just some
preliminary support.

Move PMAN LIODN to upper half of register

Despite having only one LIODN, the PMAN LIODN is stored in the
upper half of the register. Re-use the 2-LIODN code and just
set the LIODN as if the second one is 0. This results in the
actual LIODN being written to the upper half of the register.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:22 -05:00
York Sun
d1001e3f0c powerpc/corenet2: Add SerDes for corenet2
Create new files to handle 2nd generation Chassis as the registers are
organized differently.

 - Add SerDes protocol parsing and detection
 - Add support of 4 SerDes
 - Add CPRI protocol in fsl_serdes.h
	The Common Public Radio Interface (CPRI) is publicly available
	specification that standardizes the protocol interface between the
	radio equipment control (REC) and the radio equipment (RE) in wireless
	basestations. This allows interoperability of equipment from different
	vendors,and preserves the software investment made by wireless service
	providers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:19 -05:00
York Sun
fd3cebd020 powerpc/mpc85xx: Add RCW bits and registers for SerDes for corenet2
Corenet 2nd generation Chassis has different RCW and registers for SerDes.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:18 -05:00
York Sun
92230d49da powerpc/e6500: Move QCSP registers for QMan v3
The QCSP registers are expanded and moved from offset 0 to offset 0x1000
for SoCs with QMan v3.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:18 -05:00
York Sun
f8f85b049c powerpc/mpc85xx: expand SERDES reference clock select bit
Expand the reference clock select to three bits
000: 100 MHz
001: 125 MHz
010: 156.25MHz
011: 150 MHz
100: 161.1328125 MHz
All others reserved

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:17 -05:00
York Sun
9a653a9810 powerpc/mpc85xx: Fix core cluster PLL calculation for Chassis generation 2
Corenet based SoCs have different core clocks starting from Chassis
generation 2. Cores are organized into clusters. Each cluster has up to
4 cores sharing same clock, which can be chosen from one of three PLLs in
the cluster group with one of the devisors /1, /2 or /4. Two clusters are
put together as a cluster group. These two clusters share the PLLs but may
have different divisor. For example, core 0~3 are in cluster 1. Core 4~7
are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2
are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group
A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have
PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1.

PME and FMan blocks can take different PLLs, configured by RCW.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:16 -05:00
York Sun
f77329cfcf powerpc/mpc85xx: change RCW MEM_PLL_PLAT for Chassis generation 2
Chassis generation 2 has different mask and shift. Use macro instead of
magic numbers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:15 -05:00
York Sun
6d2b9da19c powerpc/mpc85xx: Enable L2 at the beginning of U-boot for E6500
Using E6500 L1 cache as initram requires L2 cache enabled.
Add l2-cache cluster enabling.

Setup stash id for L1 cache as (coreID) * 2 + 32 + 0
Setup stash id for L2 cache as (cluster) * 2 + 32 + 1
Stash id for L2 is only set for Chassis 2.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:15 -05:00
York Sun
553ae6f8f2 powerpc/DPAA: Fix compiling error
FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined.
Remove the #ifdef.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:14 -05:00
Timur Tabi
4905443f1c powerpc/85xx: Add P5040 processor support
Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:

Four P5040 single-threaded e5500 cores built
    Up to 2.4 GHz with 64-bit ISA support
    Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
    2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
        support Up to 1600MT/s
    Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
    Packet parsing, classification, and distribution (FMAN)
    Queue management for scheduling, packet sequencing and
    congestion management (QMAN)
    Hardware buffer management for buffer allocation and
    de-allocation (BMAN)
    Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
    20 lanes at up to 5 Gbps
    Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
    Two 10 Gbps Ethernet MACs
    Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
    Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
    Two serial ATA (SATA 2.0) controllers
    Two high-speed USB 2.0 controllers with integrated PHY
    Enhanced secure digital host controller (SD/MMC/eMMC)
    Enhanced serial peripheral interface (eSPI)
    Two I2C controllers
    Four UARTs
    Integrated flash controller supporting NAND and NOR flash
DMA
    Dual four channel
Support for hardware virtualization and partitioning enforcement
    Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
    Secure boot, secure debug, tamper detection, volatile key storage

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:13 -05:00
Timur Tabi
fd946040f1 powerpc/85xx: define SRIO LIODN functions only if SRIO is defined
The P5040 does not have SRIO support, so there are no SRIO LIODNs.
Therefore, the functions that set the SRIO LIODNs should not be compiled.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:13 -05:00
Laurentiu Tudor
e389a377ee powerpc/85xx: introduce SET_PCI_LIODN_BASE, for setting PCI LIODNs
The liodn for the new PCIE controller included in P5040DS is no longer set
through a register in the guts register block but with one in the PCIE
register block itself.  Update the PCIE CCSR structure to add the new liodn
register and add a new dedicated SET_PCI_LIODN_BASE macro that puts
the liodn in the correct register.

Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:12 -05:00
Liu Gang
d59c557049 powerpc/srio: Workaround for srio erratrm a004034
Erratum: A-004034
Affects: SRIO

Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.

An SRIO port configured as a 4x port may see one of these scenarios:

1.	One or more lanes fails to achieve lane synchronization.
	Depending on which lanes fail, this may result in downtraining
	from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).

2.	The link may fail to achieve lane alignment as a 4x, even
	though all 4 lanes achieve lane synchronization, and downtrain
	to a 1x. An SRIO port configured as a 1x port may fail to complete
	port initialization (PnESCSR[PU] never deasserts) because of
	scenario 1.

Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:12 -05:00
Zang Roy-R61911
4e0be34a85 P4080/esdhc: make the P4080 ESDHC13 errata workaround conditional
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 03:04:28 -05:00
Chris Packham
168e5bc409 mpc85xx: make gpio_direction_output respect value
Users of familiar with the Linux gpiolib API expect that value parameter
to gpio_direction_output reflects the initial state of the output pin.
gpio_direction_output was always driving the output low, now it drives
it high or low according to the value provided.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 03:03:16 -05:00
Simon Glass
a7e5ee9ebb powerpc: Change bi_baudrate and global data baudrate to int
These don't need to be longs, so change them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19 15:25:45 -07:00
Stefan Roese
a821d08dca ppc4xx: Remove AP1000 board support
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Stefan Roese
dee9c534db ppc4xx: Remove ML2 board support
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Stefan Roese
99bcad1809 ppc4xx: Remove IOP480 support
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Tom Rini
5675b50916 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2012-09-25 12:23:55 -07:00
Anatolij Gustschin
e5ab702a6c powerpc: re-add bi_ip_addr to bd_t struct
Since commit 50a47d0523
(net: punt bd->bi_ip_addr) booting old 2.4.x ppc kernels
is broken due to changed offsets of the fields in struct bd_t.
Offsets of the fields after removed bi_ip_addr are wrong,
causing wrong bus clocks and console baudrate configurations
and various other issues. Re-add the bi_ip_addr field to preserve
backward compatibility with older ppc kernels. Setting bi_ip_addr
in board.c is not really needed, grepping in the 2.4 linux tree
shows that bi_ip_addr is not accessed there. Adding bi_ip_addr
to struct bd_t for other arches isn't needed it seems. bd_t is
not used by other arches in the 2.4 linux tree.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
2012-09-02 22:55:59 +02:00
Andy Fleming
98ae9ac434 Revert "powerpc: Fix declaration type for I/O functions"
This reverts commit 20959471b5.
2012-08-23 12:16:57 -05:00
Scott Wood
3ea21536d7 powerpc/85xx: clear out TLB on boot
Instead of just shooting down the entry that covers CCSR, clear out
every TLB entry that isn't the one that we're executing out of.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:57 -05:00
York Sun
7ac3cc20e0 powerpc/mpc8xxx: Move HWCONFIG_BUFFER_SIZE into config.h
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:56 -05:00
York Sun
a4c66509f1 powerpc/mpc8xxx: Enable 3-way and 4-way DDR interleaving
Restructure DDR interleaving option to support 3 and 4 DDR controllers
for 2-, 3- and 4-way interleaving.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:55 -05:00
York Sun
73b5396b25 powerpc/mpc8xxx: Add fine timing support for DDR3
When the DDR3 speed goes higher, we need to utilize fine offset
from SPD.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:55 -05:00
York Sun
709389b654 powerpc/mpc8xxx: fix core id for multicore booting
For the cores with multiple threads, we need to figure out which physical
core a thread belongs. To match the core ids, update PIR registers and
spin tables.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:55 -05:00
Kumar Gala
ffdf8890ae Added new ext fields to IFC
In case more than 32 bit address is used, the EXT bit should be set.
Need to fix up address map for IFC #CS for 4, also need to move # of IFC
banks into config_mpc85xx.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:55 -05:00
Kumar Gala
50d96e95b4 Add IFC offset for DPAA/Corenet platforms
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:55 -05:00
Kumar Gala
5b6b85ae63 Add e6500 processor detection
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
York Sun
123bd96d53 powerpc/mpc8xxx: use topology registers to calculate number of cores
We have actual topology infomation to find out exactly which core is present.
Calculate the number of cores if not specified.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
York Sun
1ca8690d27 powerpc/mpc8xxx: Add immap for topology and rcpm registers
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Prabhakar Kushwaha
3854173aa8 powerpc/mpc85xx: Add IFC LAW target ID for FSL High-End SoC
Freescale's High-End SoC are going to have Integrated Flash controller
(IFC)'s support.

So add IFC LAW target ID support for High-End SoC or corenet SoC.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Prabhakar Kushwaha
e4879afba3 powerpc/mpc85xx:Enable debugger support to missed e500v2 SoC
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). Need to define define
CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.

Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for
debug support.

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Scott Wood
33eee330cc powerpc/fsl-corenet: work around erratum A004510
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.

To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.

The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.

We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline.  It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.

Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that.  We make it guarded so that we should never
see a speculative load, and we never do an explicit load.  Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward.  Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.

NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum.  This is the responsibility
of the OS that sets up PAMU.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Scott Wood
3e978f5dc8 powerpc/fsl-corenet: remove dead variant symbols
These are not supported as individual build targets, but instead
are supported by another target.

The dead p4040 defines in particular had bitrotted significantly.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Timur Tabi
055ce08004 powerpc/85xx: remove support for the Freescale P3060
The P3060 was cancelled before it went into production, so there's no point
in supporting it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:53 -05:00
Timur Tabi
99abf7ded3 powerpc/85xx: add support for FM2 DTSEC5
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:18 -05:00
Matthew McClintock
9c6b47d53e p1014rdb: set ddr bus width properly depending on SVR
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:16 -05:00
York Sun
be7bebeac2 powerpc/mpc8xxx: Remove P1015 and P1016 from CPU list
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:16 -05:00
Liu Gang
81fa73bab0 powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macro
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.

This has the following advantages:
	1. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just rewrite the new RCW with selected port,
	   then the code will get the port information by reading new RCW.
	2. It will be easier to support other boot location options, for
	   example, boot from PCIE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
Liu Gang
ff65f12699 powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build target
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:

		setenv bootmaster SRIO1
		saveenv

The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
	1. Reduce a build configuration item in boards.cfg file.
	   No longer need to build a special image for master, just use a
	   normal target image and set the "bootmaster" variable.
	2. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just set the corresponding value to "bootmaster"
	   based on the using SRIO port.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
York Sun
57125f222e powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditional
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.

Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:

fsl_cpu_a011:disable

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:13 -05:00
Prabhakar Kushwaha
20959471b5 powerpc: Fix declaration type for I/O functions
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.

Chage protoype declaration as static.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-08-09 22:24:31 +02:00
Prabhakar Kushwaha
a16a5cccfb powerpc:Fix return type & parameter passed for I/O functions
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32

Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-08-09 22:23:14 +02:00
Mike Frysinger
47fde91f0c global_data: unify global flag defines
All the global flag defines are the same across all arches.  So unify them
in one place, and add a simple way for arches to extend for their needs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09 21:46:32 +02:00
York Sun
718f2b3187 powerpc/mpc85xx: Ignore E bit for BSC9130/1
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:16 -05:00
Timur Tabi
7ee411071f powerpc/85xx: improve definition of BR_PHYS_ADDR macro
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:15 -05:00
York Sun
5e23ab0a31 powerpc/mpc85xx: Workaround for erratum CPU_A011
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
48f6a5c348 powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
Timur Tabi
7b6e80538b lib/powerpc: addrmap_phys_to_virt() should return a pointer
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.

The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-06 17:30:32 -05:00
Prabhakar Kushwaha
ad75d44239 powerpc/mpc85xx:Add debugger support for e500v2 SoC
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).

So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.

Please refer doc/README.mpc85xx for more information

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:31 -05:00
Prabhakar Kushwaha
19a8dbdc45 powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
- BSC9131 is integrated device that targets Femto base station market.
   It combines Power Architecture e500v2 and DSP StarCore SC3850 core
   technologies with MAPLE-B2F baseband acceleration processing elements.
 - BSC9130 is exactly same as BSC9131 except that the max e500v2
   core and DSP core frequencies are 800M(these are 1G in case of 9131).
 - BSC9231 is similar to BSC9131 except no MAPLE

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte shared
      L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
     Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
     and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
     Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
     operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
     ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network acceleration
      including IEEE 1588. v2 hardware support and virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single port)
      and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

This patch takes care of code pertaining to power side functionality only.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:03:25 -05:00
Mike Frysinger
50a47d0523 net: punt bd->bi_ip_addr
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr").  After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-15 17:32:05 -05:00
Liu Gang
5056c8e068 powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.

Master needs to:
	1. Set outbound SRIO windows in order to configure slave's registers
	   for the core's releasing.
	2. Check the SRIO port status when release slave core, if no errors,
	   will implement the process of the slave core's releasing.
Slave needs to:
	1. Set all the cores in holdoff by RCW.
	2. Be powered on before master's boot.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
5ffa88eca7 powerpc/corenet_ds: Master module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.

For the master module, need to finish these processes:
	1. Initialize the SRIO port and address space.
	2. Set inbound SRIO windows covered slave's u-boot image stored in
	   master's NOR flash.
	3. Master's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_MASTER_config
	4. Master must boot first, and then slave can be powered on.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:32 -05:00
Liu Gang
7d67ed58a2 powerpc/srio: Rewrite the struct ccsr_rio
Rewrite this struct for the support of two ports and two message
units registers.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24 23:58:32 -05:00
Wolfgang Denk
670c24f6f3 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  fsl_lbc: add printout of LCRR and LBCR to local bus regs
  sbc8548: Fix up local bus init to be frequency aware
  sbc8548: enable support for hardware SPD errata workaround
  sbc8548: relocate fixed ddr init code to ddr.c file
  sbc8548: Make enabling SPD RAM configuration work
  sbc8548: Fix LBC SDRAM initialization settings
  sbc8548: enable ability to boot from alternate flash
  sbc8548: relocate 64MB user flash to sane boundary
  Revert "SBC8548: fix address mask to allow 64M flash"
  MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
  eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
  eXMeritus HWW-1U-1A: Minor environment variable tweaks
2012-01-13 20:38:49 +01:00
Paul Gortmaker
3dc23c7c30 fsl_lbc: add printout of LCRR and LBCR to local bus regs
It can be handy to have these in the output when trying to
debug odd behaviour.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-13 12:56:06 -06:00
Joe Hershberger
4b56579388 mpc83xx: Add a GPIO driver for the MPC83XX family
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09 20:10:33 -06:00
Ira W. Snyder
9839709ea3 mpc85xx: support for Freescale COM Express P2020
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.

Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.

This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 09:07:51 -06:00
Timur Tabi
3e0529f742 powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
York Sun
4108508a96 powerpc/85xx: Add workaround for erratum A-003474
Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Kumar Gala
43f082bb7f powerpc/85xx: Add workaround for erratum CPU-A003999
Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
Kumar Gala
50cf3d17ce powerpc/85xx: Add support for Book-E MMU Arch v2.0
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0.  The new e6500 core from Freescale implements v2.0 of the
architecture.

Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:36:51 -06:00
Timur Tabi
5c4a3d431e powerpc/85xx: fix definition of MAS register macros
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.

Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter.  This hasn't caused any problems to date because the
parameter was always been 'tsize'.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:57 -06:00
chenhui zhao
aada81de70 powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.

Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:32 -06:00
Joe Hershberger
7d6a098219 mpc83xx: Cleanup usage of LBC constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
4713db666c mpc83xx: Fix ipic structure definition
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

Added siprr_{b,c} and sepcr for completeness.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Kim Phillips
63063cc7ae mpc83xx: fix global timer structure definition
The byte address distance between GTCFR2 and GTMDR1 is 11, not 10.

Reported-by: Shawn Bai <programassem@hotmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:51 -05:00
Anton Staaf
0991701a27 powerpc: cache: define ARCH_DMA_MINALIGN for DMA buffer alignment
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
2011-10-23 20:50:42 +02:00
Anatolij Gustschin
c4c9fbebae consolidate mdelay by providing a common function for all users
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:16:08 +02:00
Kyle Moffett
710308ee18 mpc85xx: Add inline GPIO acessor functions
To ease the implementation of other MPC85xx board ports, several common
GPIO helpers are added to <asm/mpc85xx_gpio.h>.

Since each of these compiles to no more than 4-5 instructions it would
be very inefficient to call them out of line, therefore we put them
entirely in the header file.

The HWW-1U-1A board port which these were written for strongly prefers
to set multiple GPIOs as a single batch operation, so the API is
designed around that basis.

To assist other board ports, a small set of wrappers are used which
provides a standard gpio_request() interface around the MPC85xx-specific
functions.  This can be enabled with CONFIG_MPC85XX_GENERIC_GPIO

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-21 00:04:28 -05:00
Kumar Gala
4d28db8a1e powerpc/85xx: Add support for RMan LIODN initialization
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:48 -05:00
Kumar Gala
1a0c64219d powerpc/85xx: Update setting of SRIO LIODNs
Properly set the LIODN values associated with SRIO controller.  On
P4080/P3060 we have an LIODN per port and one for the RMU.  On
P2041/P3041/P5020 we have 2 LIODNs per port.

Update the tables for all of these devices to properly handle both
styles.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:15 -05:00
Timur Tabi
7f92c3a275 powerpc/p3060: remove all references to RCW bits EC1_EXT, EC2_EXT, and EC3
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:10 -05:00
Xie Xiaobo
ae2044d8b3 powerpc/mpc8536ds: Add eSPI support for MPC8536DS
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
   so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
   to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.

Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:54 -05:00
Timur Tabi
3038171628 powerpc/85xx: fix null pointer dereference when init the SGMII TBI PHY
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.

During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used.  In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.

We also need to define the PHY registers in struct fm_mdio.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:53 -05:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Mike Frysinger
476af299b0 image: push default arch values to arch headers
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.

Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:15 +02:00
Valentin Longchamp
79843950b2 POST: add post_log_res field for post results in global data
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.

An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-10-05 22:03:10 +02:00
Graeme Russ
9558b48af0 console: Implement pre-console buffer
Allow redirection of console output prior to console initialisation to a
temporary buffer.

To enable this functionality, the board (or arch) must define:
 - CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
 - CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
 - CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)

The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
2011-10-05 22:03:09 +02:00
Shengzhou Liu
6d7b061af1 powerpc/p3060: Add SoC related support for P3060 platform
Add P3060 SoC specific information:cores setup, LIODN setup, etc

The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 09:36:28 -05:00
Kumar Gala
6b3a8d0086 powerpc/85xx: Add support for setting up RAID engine liodns on P5020
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020.  Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ).  This just handles RAID Engine in non-DPAA mode.

Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
2b3a1cdd9e powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
5ace2992b5 powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.

Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
Ruchika Gupta
7065b7d466 powerpc/p4080: Add support for secure boot flow
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
   (Please note that ISBC expects all these addresses, images to be
    validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
   at 0xcffffffc.

Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
   CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
   (The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
    created by PBL/configuration word within 0 - 3.5G memory range. The
    u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
   PBL/configuration word after switch to AS = 1

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
York Sun
d29d17d7ba powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
York Sun
4e57382faa powerpc/mpc8xxx: Add DDR2 to unified DDR driver
DDR2 has different ODT table and values. Adding table according to Samsung
application note.

Fix additive latency calculation to avoid interger underflow.

Also converted typedef dynamic_odt_t to struct dynamic_odt.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
York Sun
cae7c1b56b powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
Kumar Gala
a598643267 powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors.  The most
significant bit is used as a mfg code on MPC8536.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Roy Zang
fe1a1da038 powerpc/85xx: Add networking support to P1023RDS
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII.  The second can only do SGMII & RGMII.

We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Kumar Gala
c916d7c914 powerpc/85xx: Add support for FMan ethernet in Independent mode
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Timur Tabi
fbb9ecf749 powerpc/mp: add support for discontiguous cores
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more.  We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Poonam Aggrwal
bc6bbd6be8 fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
fb855f43a1 powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
42aee64bd9 fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Dipen Dudhat
52f90dad60 nand: Freescale Integrated Flash Controller NAND support
Add NAND support (including spl) on IFC, such as is found on the p1010.

Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC.  UBI should
work, as it does not use OOB for anything but ECC.

When hardware ECC is not enabled in CSOR, software ECC is now used.

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-09-29 19:01:04 -05:00
Timur Tabi
e46fedfeb2 powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Kumar Gala
b6c3722dfa powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Ramneek Mehresh
1b719e6654 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Weirich, Bernhard
25fb02abdf Fix incorrect array size of phy settings for 405EX
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.

Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-09-19 11:51:21 +02:00
Kumar Gala
8992738db7 powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
At some point we broke the detection of e500v1 class cores.  Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Stephen George
f110fe940c powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.

Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Mike Williams
1626308797 cleanup: Fix typos and misspellings in various files.
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
2011-07-28 21:27:36 +02:00
Becky Bruce
9cdfe28106 powerpc/mpc85xx: Add clear_ddr_tlbs function
This is useful when we just want to wipe out the TLBs.  There's currently
a function that resets the ddr tlbs to a different value; it is changed to
utilize this function.  The new function can be used in conjunction with
setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address
range as needed.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-22 03:07:47 -05:00
York Sun
23f9670f1a powerpc/mpc8xxx: Allow override DDR read-to-write turnaround time
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.

Signed-off-by: York Sun <yorksun@freescale.com>
2011-07-11 13:24:20 -05:00
Felix Radensky
aeb6716a12 powerpc/85xx: Fix pin muxing for second USB controller
On P1022/P1013 second USB controller is muxed with second
Ethernet controller. The current code to enable second USB
fails to properly clear pinmux bits used by ethernet. As a
result, Linux freezes when this controller is used. This
patch fixes the problem.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
York Sun
51d498f175 powerpc/mpc8xxx: Add 16-bit support for DDR3
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Kumar Gala
1f97987a51 powerpc/85xx: Add P2041 processor support
The P2041 is similar to P2040, however has a 10G port and backside L2

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00
Kumar Gala
8f29084a4f powerpc/fsl_pci: Fix device tree fixups for newer platforms
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up.  However on newer
platforms the simple rules no longer work.  We need to allow specifying
the PCIe compatiable string for each individual SoC.

We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-20 00:48:41 -05:00
Steven A. Falco
644362c40a PPC405EX CHIP_21 erratum
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set.  This patch implements the APM-proposed workaround.

To enable this patch for your board, add the appropriate define for your
CPU to your board header file.  See kilauea.h for more information.  The
following variants are supported:

#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY

Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.

Tested on custom boards using:

CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY  <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY     <eibach@gdsys.de>

Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-05-12 16:10:51 +02:00
Mingkai Hu
273feafefd powerpc: eSPI and eSPI controller support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29 07:34:09 -05:00
Kumar Gala
66412c6371 powerpc/85xx: Change timebase divisor to be defined per processor
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts.  All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:24 -05:00
Timur Tabi
d90fdba6ca powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.

Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly.  The
work-around is to enable and then disable bank two after bank three is
enabled.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Timur Tabi
f68d306349 powerpc/85xx: Extend SERDES9 erratum work-around to SGMII, SRIO, and AURORA
Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA.  The
current code does this only for XAUI, so extend it to the other protocols.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Timur Tabi
da30b9fd97 powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Matthew McClintock
ae425c1eca powerpc/85xx: Don't set FT_FSL_PCI_SETUP if CONFIG_PCI is not set
A lot of boards set FT_FSL_PCI_SETUP directly in their board code
and don't check to see if CONFIG_PCI is actually defined. This
will cause the board compilation to fail if CONFIG_PCI is not
defined. The p1022ds board is one such example.

Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP
around CONFIG_PCI so we can remove CONFIG_PCI and boards will
still build properly.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:40:32 -05:00
Kim Phillips
416202f672 powerpc/85xx: handle both "secX.Y" and "sec-vX.Y" properties
versioned SEC properties changed names during development, so
for now search and update LIODNs for both "secX.Y" and
"sec-vX.Y" based properties.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Lei Xu
300097669c powerpc/85xx: Enable ESDHC111 erratum on P2040/P3041/P5010/P5020 SoCs
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.

Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Roy Zang
86221f09fb powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Kumar Gala
e02aea61cb powerpc: Add P3041DS/P5020DS board support (uses corenet_ds code)
The P3041DS & P5020DS boards are almost identical (except for the
processor in them).  Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.

Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS.  We utilize some of these for SERDES clock
configuration.

Additionally, the P3041DS/P5020DS support NAND.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Emil Medve
df8af0b4a6 p4080/serdes: Implement the XAUI workaround for SERDES9 erratum
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Emil Medve
3d28c5c8ed powerpc/85xx: fsl_corenet_serdes code rework
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.

* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device

Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Haiying Wang
2a0ffb84c7 powerpc/85xx: Add device tree fixup for bman portal
Fix fdt bportal to pass the bman revision number to kernel via device tree.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:03 -05:00
Ramneek Mehresh
2bad42a0c8 powerpc/85xx: Add support for 2nd USB controller on p1_p2_rdb
Second USB controller only works for SPI and SD boot because of pin muxing

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2011-04-27 22:29:03 -05:00
Dipen Dudhat
4b77047c2a powerpc/85xx: Added PMUXCR1 and PMUXCR2 defines for P1010/P1014 SoC
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:03 -05:00
Timur Tabi
1fade70203 powerpc: fix implementation of out_8 to match the other out_XX functions
Signed-off-by: Timur Tabi <timur@freescale.com>
2011-04-28 00:55:16 +02:00
Andy Fleming
865ff85640 fsl: Change fsl_phy_enet_if to phy_interface_t
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:35 -05:00
Andy Fleming
063c12633d tsec: Convert tsec to use PHY Lib
This converts tsec to use the new PHY Lib.  All of the old PHY support
is ripped out.  The old MDIO driver is split off, and placed in
fsl_mdio.c.  The initialization is modified to initialize the MDIO
driver as well.  The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:34 -05:00
Priyanka Jain
32c8cfb23c fsl_esdhc: Deal with watermark level register related changes
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:

9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Jiang Yutang
b93f81a418 powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DS
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Zhao Chenhui
4aa8405c91 powerpc/85xx: Add some defines & registers in immap_85xx.h
* Added SDHCDCR register to GUR struct
* Added SDHCDCR_CD_INV define related to SDHCDCR
* Added Pin Muxing define related to TDM on P102x

Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05 10:18:39 -05:00
Haiying Wang
a52d2f816d powerpc/85xx: Add P1021 specific QE and UEC support
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode.  QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.

Also added relevant QE support defines unique to P1021.

The P1021 QE is shared on P1012, P1016, and P1025.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05 10:18:39 -05:00
Zhao Chenhui
c1fc2d4fc2 powerpc/85xx: don't init SDRAM when CONFIG_SYS_RAMBOOT
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05 10:18:39 -05:00
Laurentiu TUDOR
33e683541e powerpc/85xx: Fix setting of LIODN prop in PCIe nodes on P3041/P5020
We utilize the compatible string to find the node to add fsl,liodn
property to.  However P3041 & P5020 don't have "fsl,p4080-pcie"
compatible for their PCIe controllers as they aren't backwards compatible.

Allow the macro's to specify the PCIe compatible to use to allow SoC
uniqueness.  On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the
PCIe controllers.

Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:43 -05:00
Kumar Gala
b5c8753fa1 powerpc/85xx: Fixup determining PME, FMan freq
On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some
additional rules to determining the various frequencies that PME & FMan
IP blocks run at.

We need to take into account:
* Reduced number of Core Complex PLL clusters
* HWA_ASYNC_DIV (allows for /2 or /4 options)

On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs
the PME & FMan blocks utilize the second Core Complex PLL.  On SoCs
like p4080 with 4 Core Complex PLLs we utilize the third Core Complex
PLL for PME & FMan blocks.

On P2040/P3041/P5020 we have the added feature that we can divide the
PLL down further by either /2 or /4 based on HWA_ASYNC_DIV.  On P4080
this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be
set to 0 and this gets a backward compatiable /2 behavior.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:43 -05:00
Kumar Gala
c657d898bc powerpc/85xx: Specify CONFIG_SYS_FM_MURAM_SIZE
CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in
config_mpc85xx.h for those parts with a Frame Manager.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
1fbf3483b7 powerpc/85xx: Adds some P1010/P1014 SoC configuration defines
Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR
and SDHC erratum.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Kumar Gala
093cffbe9a powerpc/85xx: Support for Freescale P1024/P1025 processor
Add Support for Freescale P1024/P1025 (dual core) and
P1015/P1016 (single core) processors.

P1024 is a variant of P1020 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1025 is a variant of P1021 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1015 is a variant of P1024 processor with single core and P1016 is a
variant of P1025 processor with single core.

Added comments in config_mpc85xx.h to denote single core versions of
processors.

Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
0b3b1766b7 fsl_ddr: Adds 16 bit DDR Data width option
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Prabhakar Kushwaha
b6ccd2c9de fsl_pci: Add support for FSL PCIe controllers v2.x
FSL PCIe controller v2.1:
	- New MSI inbound window
	- Same Inbound windows address as PCIe controller v1.x

Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window

FSL PCIe controller v2.2 and v2.3:
	- Different addresses for PCIe inbound window 3,2,1
	- Exposed PCIe inbound window 0
	- New PCIe interrupt status register

Added new Interrupt Status register to struct ccsr_pci & updated pit_t array
size to reflect the 4 inbound windows.

To maintain backward compatiblilty, on V2.2 or greater controllers we
start with inbound window 1 and leave inbound 0 with its default value
(which maps to CCSRBAR).

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Haiying Wang
24995d829a powerpc/85xx: Refactor Qman/Portal support to be shared between SoCs
There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.

* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
  (features doesn't exist on P1023/P1017)

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Roy Zang
67a719da2e powerpc/85xx: Add support for Freescale P1023/P1017 Processors
Add P1023 (dual core) & P1017 (single core) specific information:
* SERDES Table
* Added P1023/P1017 to cpu_type_list and SVR list
  (fixed issue with P1013 not being sorted correctly).
* Added P1023/P1027 to config_mpc85xx.h
* Added new LAW type introduced on P1023/P1017
* Updated a few immap register/defines unique to P1023/P1017

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fdb4dad31e powerpc/85xx: Cleanup some QE related defines
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.

Also fixed up some comment style issues in immap_qe.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fbee0f7f09 powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020
Specify the number of DDR controllers, number of frame managers, number
of 1g and 10g ports.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Kumar Gala
f0f899432e powerpc/85xx: Declare fsl_ddr_set_memctl_regs in <asm/fsl_ddr_sdram.h>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.

Based on patch from Poonam Aggrwal.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Dipen Dudhat
d789b5f5bc powerpc/85xx: Add support for Integrated Flash Controller (IFC)
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.

Features supported by IFC are,
        - Functional muxing of pins between NAND, NOR and GPCM
        - Support memory banks of size 64KByte to 4 GBytes
        - Write protection capability (only for NAND and NOR)
        - Provision of Software Reset
        - Flexible Timing programmability for every chip select
        - NAND Machine
                - x8/ x16 NAND Flash Interface
                - SLC and MLC NAND Flash devices support with
                  configurable
                  page sizes of upto 4KB
                - Internal SRAM of 9KB which is directly mapped and
                  availble at
                  boot time for NAND Boot
                - Configurable block size
                - Boot chip select (CS0) available at system reset
        - NOR Machine
                - Data bus width of 8/16/32
                - Compatible with asynchronous NOR Flash
                - Directly memory mapped
                - Supports address data multiplexed (ADM) NOR device
                - Boot chip select (CS0) available at system reset
        - GPCM Machine (NORMAL GPCM Mode)
                - Support for x8/16/32 bit device
                - Compatible with general purpose addressable device
                  e.g. SRAM, ROM
                - External clock is supported with programmable division
                  ratio
        - GPCM Machine (Generic ASIC Mode)
                - Support for x8/16/32 bit device
                - Address and Data are shared on I/O bus
                - Following Address and Data sequences can be supported
                  on I/O bus
                       - 32 bit I/O: AD
                       - 16 bit I/O: AADD
                       - 8 bit I/O : AAAADDDD
                - Configurable Even/Odd Parity on Address/Data bus
                  supported

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Prabhakar Kushwaha
28747f9bb1 powerpc/85xx: Add SERDES support for P1010/P1014
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are only
ever connected on SERDES.

Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Prabhakar Kushwaha
b03a466d6c powerpc/85xx: Handle PCIe initialization requires for P1021 class SoCs
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe.  Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-29 07:41:37 -05:00
Jiang Yutang
2d7534a344 powerpc/85xx: Enable various errata on P1022/P1013 SoCs
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.

Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-28 09:04:26 -05:00
York Sun
08b3f7599f powerpc/mpc8xxx: fix recognition of DIMMs with ECC and Address Parity
To recognize DIMMs with ECC capability by testing ECC bit only. Not to be
confused by Address Parity bit.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-24 09:20:49 -05:00
Wolfgang Denk
fced09ae38 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2011-02-09 20:50:26 +01:00
Dirk Eibach
2da0fc0d0f ppc4xx: Add DLVision-10G board support
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-02-07 11:13:16 +01:00
York Sun
91671913f7 powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
         calibrate to incorrect values

These two workarounds must be implemented together because they touch
common registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
York Sun
eb0aff77c8 powerpc/85xx: Rename MPC8572 DDR erratum to DDR115
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
Kumar Gala
5103a03a0b fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Kumar Gala
6e7f0bc0ce powerpc/85xx: Enable ESDHC111 Erratum on P2010/P2020 SoCs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Wolfgang Denk
d1a24f0618 Minor Coding Style Cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-02-02 22:36:10 +01:00
York Sun
6b06d7dc07 corenet_ds: Extend board specific parameters
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00
York Sun
fa8d23c0ee mpc85xx: Implement workaround for erratum DDR-A003
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00
York Sun
e1fd16b6f5 mpc85xx: Enable unique mode registers and dynamic ODT for DDR3
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.

Enable address parity and RCW by default for RDIMMs.

Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.

Use a formula to calculate rodt_on for timing_cfg_5.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
York Sun
d2a9568c57 mpc85xx: Adding more registers and options
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.

Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Kumar Gala
243be8e296 powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headers
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.

Eventually this should be handled by Kconfig & defconfigs

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-19 22:58:23 -06:00
Kumar Gala
f193e3da98 powerpc/p2040: Add various p2040 specific information
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b5debec5b5 powerpc/85xx: Add Support for Freescale P1014 Processor
The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b8cdd01462 powerpc/85xx: Add Support for Freescale P1010 Processor
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Prabhakar
17028be238 Fix wrong CONFIG_SYS_MPC85xx_SERDES1_ADDR
CONFIG_SYS_MPC85xx_SERDES1_ADDR was defined wrong as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES2_OFFSET.
It should be as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2011-01-19 22:58:23 -06:00
Kumar Gala
f133796da8 powerpc/85xx: Add the workaround for erratum ELBC-A001 (enable on P4080)
Simultaneous FCM and GPCM or UPM operation may erroneously trigger bus
monitor timeout.  Set timeout to maximum to avoid.

Based on a patch from Lan Chunhe <b25806@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
868da5936e powerpc/85xx: Add the workaround for erratum CPC-A003 (enable on P4080)
CoreNet Platform Cache single-bit data error scrubbing will cause data
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
1d2c2a62e3 powerpc/85xx: Add the workaround for erratum CPC-A002 (enable on P4080)
CoreNet Platform Cache single-bit tag error scrubbing will cause tag
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
3dbd5d7d7e powerpc/8xxx: Move fsl_is_spd() into generic 8xxx ddr code
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
5655136208 powerpc/86xx: Enable common SRIO init code
Add the needed defines and code to utilize the common 8xxx srio init
code to setup LAWs and modify device tree if we have SRIO enabled on a
board.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:21 -06:00
Kumar Gala
a09b9b68d4 powerpc/8xxx: Refactor SRIO initialization into common code
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO.  We mimic what we do with PCIe
controllers for SRIO.

We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.

We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.

Introduced the following standard defines for board config.h:

CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available

(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)

[ These mimic what we have for PCI and PCIe controllers ]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:21 -06:00
Peter Tyser
213ac73e2c fsl_pci: Update PCIe boot ouput
This change does the following:
- Adds printing of negotiated link width.  This information can be
  useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
  Previously boards that did not implement it would print unsightly
  output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
  clear that the "base address XYZ" value refers to the base address of
  the internal processor PCIe registers and not a standard PCI BAR
  value.
- Changes "PCIE" output to the standard "PCIe"

Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06

After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:21 -06:00
Kumar Gala
a4aafcc990 powerpc/fsl-pci: Add generic code to setup PCIe controllers
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled.  After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.

We also provide a per controller (rather than all) for some systems that
may have special requirements.

Finally, we refactor the code used by the P1022DS to utilize the new
generic code.

Based on patch by: Li Yang <leoli@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Kumar Gala
3a0e3c27a5 powerpc/fsl-pci: Determine pci_controller based on cfg addr for dts fixup
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus.  Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.

Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:19 -06:00
Becky Bruce
70961ba414 mpc85xx: rename sdram_init() lbc_sdram_init()
sdram_init() is used to initialize sdram on the lbc.  Rename it
accordingly.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Becky Bruce
38dba0c2ff mpc85xx boards: initdram() cleanup/bugfix
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts.  Most
of the initdram() functions were identical, with 2 common differences:

1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others.  I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.

2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document.  It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled.  This seems bad.

The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Kumar Gala
5d27e02c04 powerpc/8xxx: Replace is_fsl_pci_cfg with is_serdes_configured
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Piergiorgio Beruto
afabe4b94e powerpc/85xx: Fix wrong SVR value for MPC8567 and MPC8567E processors
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
York Sun
28a966715b Adding fixed sdram setting for cornet_ds board
800, 900, 1000, 1200MT/s data rate parameters are added for fixed sdram
setting. SPD based parameters and fixed parameters can be toggled by hwconfig.
To use fixed parameters,

hwconfig=fsl_ddr:sdram=fixed

To use SPD parameters,

hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:38:39 -05:00
Kumar Gala
a1964ea5c2 powerpc/8xxx: Add fdt_fixup_phy_connection helper
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:27:18 -05:00
Kumar Gala
f8c42495e0 powerpc/fsl: Introduce common enum for PHY types
Have a common enum for phy types that we use in the UCC driver.  We will
also use this enum for dealing with phy connection fixup in the device
tree.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:27:18 -05:00
John Rigby
fca43cc801 boot: change some arch ifdefs to feature ifdefs
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.

Use CONFIG_SYS_BOOT_<FEATURE> defines instead.

CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD

Define these as appropriate in arch/include/asm/config.h files.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:53:32 +02:00
Peter Tyser
d98b0523cf powerpc: Cleanup BOOTFLAG_* references
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-18 22:38:56 +02:00
Damien Dusha
29c6fbe047 MPC5121: Add USB EHCI support
Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com>
Signed-off-by: Damien Dusha <d.dusha@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-10-18 22:33:32 +02:00
Kumar Gala
3c6a22b962 powerpc/p4080: Add new CPC register - HDBCR0
Manual was updated to add a new register for disabling CDQ speculation.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07 09:49:47 -05:00
Stefan Roese
eb011d27aa ppc4xx: Remove some testing hacks from ppc4xx.h
I accidentally left these hacks in the code while doing the big header
cleanup. Let's remove it now.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-04 11:20:11 +02:00
Stefan Roese
c96be63aab ppc4xx: Add defines for COM3 & COM4 (UART2 & UART3) on 440EPx/GRx
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-04 11:19:43 +02:00
Tirumala Marri
1b8fec1393 APM821xx: Add CPU support
APM821XX is a new line of SoCs which are derivatives of
PPC44X family of processors. This patch adds support of CPU, cache,
tlb, 32k ocm, bootstraps, PLB and AHB bus.

Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-04 11:15:02 +02:00
Stefan Roese
550650ddd0 ppc4xx: Use common NS16550 driver for PPC4xx UART
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.

The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.

All PPC4xx board config headers are changed to use this common NS16550
driver now.

Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
afabb498b7 ppc4xx: Big header cleanup part 2, mostly PPC405 related
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.

As a part from this cleanup, the GPIO definitions for PPC405EP are
corrected. The high and low parts of the registers (for example
CONFIG_SYS_GPIO0_OSRL vs. CONFIG_SYS_GPIO0_OSRH) have been defined in
the wrong order. This patch now fixes this issue by switching these
xxxH and xxxL values. This brings the GPIO 405EP port in sync with all
other PPC4xx ports.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
5e7abce991 ppc4xx: Big header cleanup, mostly PPC440 related
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.

This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
0988776288 ppc4xx: Move gpio.h to ppc4xx-gpio.h since its ppc4xx specific
Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
b36df56115 ppc4xx: Move ppc4xx headers to powerpc include directory
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Wolfgang Denk
ea882baf9c New implementation for internal handling of environment variables.
Motivation:

* Old environment code used a pessimizing implementation:
  - variable lookup used linear search => slow
  - changed/added variables were added at the end, i. e. most
    frequently used variables had the slowest access times => slow
  - each setenv() would calculate the CRC32 checksum over the whole
    environment block => slow
* "redundant" envrionment was locked down to two copies
* No easy way to implement features like "reset to factory defaults",
  or to select one out of several pre-defined (previously saved) sets
  of environment settings ("profiles")
* No easy way to import or export environment settings

======================================================================

API Changes:

- Variable names starting with '#' are no longer allowed

  I didn't find any such variable names being used; it is highly
  recommended to follow standard conventions and start variable names
  with an alphanumeric character

- "printenv" will now print a backslash at the end of all but the last
  lines of a multi-line variable value.

  Multi-line variables have never been formally defined, allthough
  there is no reason not to use them. Now we define rules how to deal
  with them, allowing for import and export.

- Function forceenv() and the related code in saveenv() was removed.
  At the moment this is causing build problems for the only user of
  this code (schmoogie - which has no entry in MAINTAINERS); may be
  fixed later by implementing the "env set -f" feature.

Inconsistencies:

- "printenv" will '\\'-escape the '\n' in multi-line variables, while
  "printenv var" will not do that.

======================================================================

Advantages:

- "printenv" output much better readable (sorted)
- faster!
- extendable (additional variable properties can be added)
- new, powerful features like "factory reset" or easy switching
  between several different environment settings ("profiles")

Disadvantages:

- Image size grows by typically 5...7 KiB (might shrink a bit again on
  systems with redundant environment with a following patch series)

======================================================================

Implemented:

- env command with subcommands:

  - env print [arg ...]

    same as "printenv": print environment

  - env set [-f] name [arg ...]

    same as "setenv": set (and delete) environment variables

    ["-f" - force setting even for read-only variables - not
    implemented yet.]

  - end delete [-f] name

    not implemented yet

    ["-f" - force delete even for read-only variables]

  - env save

    same as "saveenv": save environment

  - env export [-t | -b | -c] addr [size]

    export internal representation (hash table) in formats usable for
    persistent storage or processing:

	-t:	export as text format; if size is given, data will be
		padded with '\0' bytes; if not, one terminating '\0'
		will be added (which is included in the "filesize"
		setting so you can for exmple copy this to flash and
		keep the termination).
	-b:	export as binary format (name=value pairs separated by
		'\0', list end marked by double "\0\0")
	-c:	export as checksum protected environment format as
		used for example by "saveenv" command
	addr:	memory address where environment gets stored
	size:	size of output buffer

	With "-c" and size is NOT given, then the export command will
	format the data as currently used for the persistent storage,
	i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
	prepend a valid CRC32 checksum and, in case of resundant
	environment, a "current" redundancy flag. If size is given, this
	value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
	checksum and redundancy flag will be inserted.

	With "-b" and "-t", always only the real data (including a
	terminating '\0' byte) will be written; here the optional size
	argument will be used to make sure not to overflow the user
	provided buffer; the command will abort if the size is not
	sufficient. Any remainign space will be '\0' padded.

        On successful return, the variable "filesize" will be set.
        Note that filesize includes the trailing/terminating '\0'
        byte(s).

        Usage szenario: create a text snapshot/backup of the current
	settings:

		=> env export -t 100000
		=> era ${backup_addr} +${filesize}
		=> cp.b 100000 ${backup_addr} ${filesize}

	Re-import this snapshot, deleting all other settings:

		=> env import -d -t ${backup_addr}

  - env import [-d] [-t | -b | -c] addr [size]

    import external format (text or binary) into hash table,
    optionally deleting existing values:

	-d:	delete existing environment before importing;
		otherwise overwrite / append to existion definitions
	-t:	assume text format; either "size" must be given or the
		text data must be '\0' terminated
	-b:	assume binary format ('\0' separated, "\0\0" terminated)
	-c:	assume checksum protected environment format
	addr:	memory address to read from
	size:	length of input data; if missing, proper '\0'
		termination is mandatory

  - env default -f

    reset default environment: drop all environment settings and load
    default environment

  - env ask name [message] [size]

    same as "askenv": ask for environment variable

  - env edit name

    same as "editenv": edit environment variable

  - env run

    same as "run": run commands in an environment variable

======================================================================

TODO:

- drop default env as implemented now; provide a text file based
  initialization instead (eventually using several text files to
  incrementally build it from common blocks) and a tool to convert it
  into a binary blob / object file.

- It would be nice if we could add wildcard support for environment
  variables; this is needed for variable name auto-completion,
  but it would also be nice to be able to say "printenv ip*" or
  "printenv *addr*"

- Some boards don't link any more due to the grown code size:
  DU405, canyonlands, sequoia, socrates.

	=> cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
	       Stefan Roese <sr@denx.de>,
	       Heiko Schocher <hs@denx.de>

- Dropping forceenv() causes build problems on schmoogie

	=> cc: Sergey Kubushyn <ksi@koi8.net>

- Build tested on PPC and ARM only; runtime tested with NOR and NAND
  flash only => needs testing!!

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Cc: Stefan Roese <sr@denx.de>,
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
2010-09-19 19:29:48 +02:00
Wolfgang Denk
91a76751a0 Make getenv() work before relocation.
So far, getenv() would work before relocation is most cases, even
though it was not intended to be used that way.  When switching to a
hash table based implementation, this would break a number of boards.

For convenience, we make getenv() check if it's running before
relocation and, if so, use getenv_f() internally.

Note that this is limited to simple cases, as we use a small static
buffer (32 bytes) in the global data for this purpose.

For this reason, it is also not a good idea to convert all current
uses of getenv_f() into getenv() - some of the existing use cases need
to be able to deal with longer variable values, so getenv_f() is still
needed and recommended for use before relocation.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-19 19:29:48 +02:00
Kumar Gala
ed062e0f6c powerpc/85xx: Rename Security Engine Job Queue to Job Ring to match docs
Official docs call it the Job Ring not Job Queue for the p4080 security
block.  Match the docs to reduce confusion.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19 02:06:13 -05:00
Kim Phillips
680c613a5c powerpc/8xxx: share PIC defines among 85xx and 86xx
fixes breakeage introduced by commit
a37c36f4e7 "powerpc/8xxx: query
feature reporting register for num cores on unknown cpus"

Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19 02:06:13 -05:00
Wolfgang Denk
fe8d63c8c7 Merge branch 'master' of git://git.denx.de/u-boot-marvell 2010-08-10 22:37:27 +02:00
Albert Aribaud
f2a37fcd9b ide: add configuration
CONFIG_IDE_SWAP_IO

This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08 05:17:05 +05:30
Kim Phillips
a37c36f4e7 powerpc/8xxx: query feature reporting register for num cores on unknown cpus
doing so helps avant garde users, such as those using simulators that
allow users to configure the number of cores, so as to not have to
manually adjust u-boot sources.  h/w should also be reliably setting
FRR NCPU in the future.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-01 11:18:45 -05:00
york
9490ff4864 powerpc/8xxx: Enable DDR3 RDIMM support
Enabled registered DIMMs using data from SPD. RDIMMs have registers
which need to be configured before using. The register configuration
words are stored in SPD byte 60~116 (JEDEC standard No.21-C). Software
should read those RCWs and put into DDR controller before initialization.

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:10 -05:00
york
7fd101c97b powerpc/8xxx: Enabled address hashing for 85xx
For 85xx silicon which supports address hashing, it can be activated by
hwconfig.

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:09 -05:00
york
5800e7ab32 powerpc/8xxx: Enable quad-rank DIMMs.
Previous code presumes each DIMM has up to two rank (chip select). Newer
DDR controller supports up to four chip select on one DIMM.

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:09 -05:00
Kumar Gala
fd3c9befa8 powerpc/p4080: Add workaround for erratum CPU22
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:57 -05:00
Kumar Gala
34a8258fea powerpc/p4080: Add support for initializing SERDES
Add support for initializing the SERDES blocks on CoreNet style QoriQ
devices and the p4080 specific SERDES tables to know which actual
componetns are enabled.

Additionally, split out the Frame Manger (FMAN) into its specific ethernet
ports instead of gross level of the full FMAN.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:57 -05:00
Kumar Gala
db977abfc8 powerpc/85xx: Add support to initialize LIODN registers and portals
On the new QorIQ/CoreNet based platforms we need to initialize the
"portals" as access into the Data Path subystem as well as Logical IO
Device Numbers (LIODN) that are used for the IOMMU (PAMU).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:56 -05:00
Kumar Gala
ebd7cb0ba9 powerpc/fsl_fman: Add initial fman immap structures
Add basic structures for Frame Manager on P4080/P3041/P5020 devices

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 08:07:47 -05:00
Kumar Gala
9ab87d04a8 powerpc/85xx: Add additional p4080 platform related defines/structs
* Added PCIE4 address, offset, DEVDISR & LAW target ID
* Added new p4080 DDR registers and defines to immap
* Add missing corenet platform DEVDISR related defines
* Updated ccsr_gur to include LIODN registers
* Add RCWSR defines
* Added Basic qman, pme, bman immap structs
* Added SATA related offsets & addresses
* Added Frame Manager 1/2 offsets & addresses
* Renamed CONFIG_SYS_TSEC1_OFFSET to CONFIG_SYS_FSL_FM1_DTSEC1_OFFSET
* Added various offsets and addresses that where missing

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 08:07:47 -05:00
Wolfgang Denk
9662317142 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2010-07-24 20:34:13 +02:00
Stefan Roese
b995d7cb2c ppc4xx: DDR/ECC: Use correct macros to clear error status
Use the correct macro instead of the hardcoded 0x4c to clear the ECC
status in the 440/460 DDR(2) error status register after ECC
initialization.

Also the non-440 parts (405EX(r) right now) and the IBM DDR PPC variants
(440GX) use a different registers to clear this error status. Use the
correct ones.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23 09:54:28 +02:00
Stefan Roese
897d6abc50 ppc4xx: Only define DDR2 registers for the correct PowerPC variants
Make sure that some SDRAM/DDR2 registers are only defined for the PPC
variants really implementing those registers.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23 09:54:22 +02:00
Kumar Gala
af0250652a powerpc/85xx: Rework MPC8536 SERDES is_serdes_configured support
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-21 00:40:16 -05:00
Kumar Gala
c26de2d8b1 powerpc/p3041: Add various p3041 related defines
There are various locations that we have chip specific info:

* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:41:19 -05:00
Kumar Gala
19dbcc96c0 powerpc/p5020: Add various p5020 related defines (and p5010)
There are various locations that we have chip specific info:

* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:41:19 -05:00
Kumar Gala
6525d51fa5 powerpc/85xx & 86xx: Rework ft_fsl_pci_setup to not require aliases
Previously we used an alias the pci node to determine which node to
fixup or delete.  Now we use the new fdt_node_offset_by_compat_reg to
find the node to update.

Additionally, we replace the code in each board with a single macro call
that makes assumes uniform naming and reduces duplication in this area.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:40:06 -05:00
Kumar Gala
dd2cda3dbd powerpc/86xx: Move PCI/PCIe address defines into common immap_86xx.h
Remove dupliacted setting of PCI/PCIe address and offsets in board
config.h.  Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on
MPC8641 boards since its really PCIE controllers and not PCI.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:37:11 -05:00
Kumar Gala
99d9c07edc powerpc/85xx: Move PCI/PCIe address defines into common immap_85xx.h
Remove dupliacted setting of PCI/PCIe address and offsets in board
config.h.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:37:11 -05:00
Kumar Gala
9f43d7997e powerpc/85xx: Move p1022ds slot code into board file
The code to map SERDES configs to slot names is board specific and not
chip specific.  Thus it should live in board/freescale/p1022ds/ and not
in arch/powerpc/cpu/.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Timur Tabi
c59e1b4d07 powerpc: add support for the Freescale P1022DS reference board
Specifics:

1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Timur Tabi
752bc33530 fsl: add LAW target to fsl_pci_info structure
Add the LAW target (enum law_trgt_if) to the fsl_pci_info structure, so that
we can capture the LAW target for a given PCI or PCIE controller.  Also update
the SET_STD_PCI_INFO and SET_STD_PCIE_INFO macros to assign the
LAW_TRGT_IF_PCI[E]_x macro to the LAW target field of the structure.

This will allow future PCI[E] code to configure the LAW target automatically,
rather than requiring each board to it for each PCI controller separately.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Kumar Gala
ae3913922a powerpc/85xx: Add support for link stack & STAC on e5500
The e5500 has a link register stack and segment target address cache.
Its safe to enable these bits on older e500 cores as the bits are
implemented in the register.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Becky Bruce
f2d9a5da29 powerpc 83xx/85xx: Merge lbc upmconfig code
Each platform had its own version of the upmconfig, despite the
init process being identical.  Now that we have a spot for common
lbc code, create a common upmconfig() there.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Becky Bruce
e71755f887 drivers/misc/fsl_law.c: Rearrange code to avoid duplication
The current code redefines functions based on FSL_CORENET_ vs not -
create macros/inlines instead that hide the differences.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Becky Bruce
70e02bca6b mpc85xx: Add print_tlbcam() function
This dumps out the contents of TLB1 on 85xx-based systems.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Becky Bruce
4e63df300f mpc85xx: tlb.c cleanups
Extract the operation to read a tlb into a function - we will need
this later to print out the tlbs, and there's no point in duplicating
the code.  Create a TSIZE_TO_BYTES macro to deal with the conversion
from the MAS field to an actual size instead of duplicating this in code.
There are a few misc other minor cleanups.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Becky Bruce
f51cdaf191 83xx/85xx/86xx: LBC register cleanup
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers.  Merge
this into a single spot.

To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.

In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.

I have done a successful ppc build all and tested a board or two from
each processor family.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Kumar Gala
8f3a7fa4a2 powerpc/8xxx: Add is_core_disabled to remove disabled cores from dtb
If we explicitly disabled a core remove it from the dtb we pass on to
the kernel.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:08 -05:00
Kim Phillips
22f292c7b2 powerpc/8xxx: Add base support for the SEC4
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:07 -05:00
Kim Phillips
929a213830 powerpc/8xxx: Distinguish between incompatible SEC h/w types
CONFIG_SYS_FSL_SEC_COMPAT is set to 2 for the SEC 2.x and SEC 3.x.
Parts with newer SEC h/w versions will increment the number to
accomodate incompatible code changes.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:07 -05:00
Ilya Yanok
7c619ddcee mpc8308: support for Freescale MPC8308 cpu
This patch adds basic support for Freescale MPC8308 CPU. Serial ports,
NOR flash and integrated Ethernet controllers are supported.
PCI Express is also supported. eSDHC, NAND and USB may work but aren't
tested (using ULPI PHY requires additional patch).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09 15:00:54 -05:00
Stefan Roese
2909ac03f4 ppc4xx: Add DDR1/2 macros in ppc4xx-sdram.h for non-405EX as well
This patch adds some DDR(2) macros to all PPC4xx's equipped with
this IBM DDR1/2 controller.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-01 10:26:20 +02:00
Stefan Roese
066003b2c5 ppc4xx: Enable overwriting of default scan window for IBM DDR2 controller
This patch makes it possible to overwrite the default auto-calibration
scan window (SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR] values) with
board specific values. The parameters of the weak default function are
corrected as well. This way we don't need the casts any more.

This feature will be used by an upcoming PPC460GT board port.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-01 10:26:10 +02:00
Timur Tabi
6e37a04407 fsl/85xx: add clkdvdr and pmuxcr2 to global utilities structure definition
Add the 'clkdvdr' and 'pmuxcr2' registers to the 85xx definition of
struct ccsr_gur.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-30 11:10:32 -05:00
Kumar Gala
6ab4011b79 85xx: Add is_serdes_configured() support to MPC8536 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-12 04:53:50 -05:00
Ron Madrid
3b439792b0 mpc83xx: Add UPMA configuration to SIMPC8313
Added UPM array table, upmconfig, and Local Bus configuration support for SIMPC8313

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-05-07 12:19:52 -05:00
Wolfgang Denk
8e98f5f70b Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2010-04-27 23:02:12 +02:00
Kumar Gala
7e1afb62a7 ppc: Split MPC83xx SERDES code from MPC85xx/MPC86xx/QorIQ
The MPC83xx SERDES control is different from the other FSL PPC chips.
For now lets split it out so we can standardize on interfaces for
determining of a device on SERDES is configured.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-26 22:37:57 -05:00
Lan Chunhe
3f0202ed13 mpc85xx: Add the ability to set LCRR[CLKDIV] to improve R/W speed of flash
Signed-off-by: Lan Chunhe <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:56 -05:00
Dave Liu
0c955dafab 85xx: clean up the io_sel for PCI express of P1022
clean up the wrong io_sel for PCI express according to latest manual.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:56 -05:00
Dave Liu
f8d05e5e58 fsl-ddr: add the macro for Rtt_Nom definition
add the macro definition for Rtt_Nom termination value for DDR3

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:53 -05:00
Kumar Gala
1231c498e0 ppc/p4080: Add p4080 DEVDISR2 & SRDS_PLLCR0 defines
Added some needed fines and some misc additional defines
used by p4080 initialization.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:52 -05:00
Dave Liu
17d90f31a8 ppc/p4080: Extend the GUTS memory map
Extend pin control and clock control to GUTS memory map

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:52 -05:00
Srikanth Srinivasan
ab48ca1a66 ppc/p4080: Fix synchronous frequency calculations
When DDR is in synchronous mode, the existing code assigns sysclk
frequency to DDR frequency.  It should be synchronous with the platform
frequency.  CPU frequency is based on platform frequency in synchronous
mode.

Also fix:

* Fixes the bit mask for DDR_SYNC (RCWSR5[184])
* Corrects the detection of synchronous mode.

Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:51 -05:00
Anatolij Gustschin
a3921eefa1 mpc5121: add support for PDM360NG board
PDM360NG is a MPC5121E based board by ifm ecomatic gmbh.

Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 22:56:37 +02:00
Anatolij Gustschin
5d937e8b59 mpc512x: make MEM IO Control configuration a board config option
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 22:56:34 +02:00
Anatolij Gustschin
e3b28e6732 mpc512x: add multi serial PSC support
Extend mpc512x serial driver to support multiple PSC ports.

Subsequent patches for PDM360NG board support make use of this
functionality by defining CONFIG_SERIAL_MULTI in the board config
file. Additionally the used PSC devices are specified by defining
e.g. CONFIG_SYS_PSC1, CONFIG_SYS_PSC4 and CONFIG_SYS_PSC6.

Support for PSC devices other than 1, 3, 4 and 6 is not added
by this patch because these aren't used currently. In the future
it can be easily added using DECLARE_PSC_SERIAL_FUNCTIONS(N) and
INIT_PSC_SERIAL_STRUCTURE(N) macros in cpu/mpc512x/serial.c.
Additionally you have to add code for registering added
devices in serial_initialize() in common/serial.c.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 22:56:30 +02:00
Wolfgang Denk
a77034a8df Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2010-04-24 21:16:57 +02:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00