Commit graph

5330 commits

Author SHA1 Message Date
Marek Vasut
4425e62856 arm: socfpga: clock: Drop nonsense inlining from clock manager code
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler. Scrub this hint.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Marek Vasut
09f7e314e4 arm: socfpga: clock: Implant order into bit definitions
The bit definitions for clock manager are complete chaos. Implement
some basic logical order into them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Marek Vasut
665e4caf02 arm: socfpga: sysmgr: Clean up system manager
Clean up the system manager register definition and add the missing
register definitions in place.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Pavel Machek
de6da9255a arm: socfpga: Add watchdog disable for socfpga
This adds watchdog disable. It is neccessary for running Linux kernel.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

V2: Move RSTMGR_PERMODRST_L4WD0_LSB to reset_manager.h
    Reset watchdog only if CONFIG_HW_WATCHDOG is undefined (the default)
2014-10-06 17:46:48 +02:00
Marek Vasut
be324354ee arm: socfpga: Clean up base address file
Sort the list of functional block addresses and fix indentation.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:46:48 +02:00
Pavel Machek
e1f006f438 arm: socfpga: Complete the list of base addresses
Add base addresses for all subsystems as documented in the
Cyclone V HPS documentation.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:46:48 +02:00
Marek Vasut
ff7e9700ed arm: cache: Add support for write-allocate D-Cache
Add configuration for the write-allocate mode of L1 D-Cache on ARM.
This is needed for D-Cache operation on Cortex-A9 on the SoCFPGA .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:40:21 +02:00
Christian Gmeiner
39d0973300 imx6: add Bachmann OT1200 board
This patch adds support for the OT1200 series of devices.

Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio

For more details see README.

Changes v1 > v2
  - make use of enable_cspi_clock(..)
  - fix usage of OUTPUT_40OHM define
  - added README

Changes v2 > v3
  - improve spelling in README
  - added own copy of mx6q_4x_mt41j128.cfg

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-06 17:24:28 +02:00
Masahiro Yamada
66cba041fe ARM: UniPhier: add Kconfig and defconfig
This commit allows to build Panasonic UniPhier family:
PH1-LD4, PH1-Pro4, PH1-sLD8

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05 14:10:09 +09:00
Masahiro Yamada
5894ca007d ARM: UniPhier: add UniPhier SoC support code
These are used by Panasonic UniPhier SoC family.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05 14:10:09 +09:00
Nitin Garg
13bc86037e imx6sx: Fix i.MX6SX HAB api function table offset
i.MX6SX ROM implements unified table sections.
The HAB function table is at offset 0x100. Update
the HAB function pointers accordingly.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-01 09:10:28 +02:00
Ye.Li
5546ad0734 usb: ehci-mx6: Rename the USB register base address
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.

This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29 10:33:27 +02:00
Ye.Li
9293d7fd50 imx: mx6: Checking PLL2 PFD0 and PFD2 for periph_clk before PFD reset
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR
register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source,
do not reset this PFD to avoid system hang. Customers may set this
in DDR script or use BT_FREQ to select low freq boot.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29 10:24:07 +02:00
Marek Vasut
7c604e98c2 arm: mxs: Wait for DRAM to start
Instead of waiting for a fixed period of time and hoping for the best
that the DRAM will start, read back an EMI status register which tells
us exactly when the DRAM started.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Marek Vasut
be0ecdbed5 arm: mxs: Wait when disabling VDDMEM current limiter
According to i.MX23 datasheet Table 32-17, we must wait for the supply
to settle before disabling the current limiter. Indeed, not waiting a
little here causes the system to crash at times.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Tom Rini
2c2277f15c Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2014-09-26 09:57:52 -04:00
Tom Rini
2c3dc792b6 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-09-26 09:51:18 -04:00
Chris Packham
039b77396a powerpc: add --bss-plt to LDFLAGS
With some versions of gcc (that we know of 4.6.3 and 4.8.2 are affected)
it is necessary to specify --bss-plt to get the final blrl in the
_GOT2_TABLE_. Without this the last symbol does not get it's address
relocated.  For the P2041RDB board this ended up being
NetArpWaitTimerStart which caused the ARP packets to timeout
immediately.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-25 09:22:37 -07:00
York Sun
c7eae7fcb1 board/ls1021aqds: Add DDR4 support
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
2014-09-25 09:12:12 -07:00
York Sun
40f8dec54d armv8/fsl-lsch3: Release secondary cores from boot hold off with Boot Page
Secondary cores need to be released from holdoff by boot release
registers. With GPP bootrom, they can boot from main memory
directly. Individual spin table is used for each core. Spin table
and the boot page is reserved in device tree so OS won't overwrite.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-09-25 08:36:19 -07:00
York Sun
d9c68b1444 ARMv8/ls2085a_emu: Enable DP-DDR as standalone memory block
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).

Signed-off-by: York Sun <yorksun@freescale.com>
2014-09-25 08:36:18 -07:00
York Sun
1d71efbb03 driver/ddr: Restruct driver to allow standalone memory space
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-09-25 08:36:18 -07:00
Masahiro Yamada
783e6a72b8 kconfig: move CONFIG_OF_* to Kconfig
This commit moves:
  CONFIG_OF_CONTROL
  CONFIG_OF_SEPARATE
  CONFIG_OF_EMBED
  CONFIG_OF_HOSTFILE

Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.

Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
2014-09-25 09:27:50 -04:00
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Masahiro Yamada
ab7cb4eefa mpc8xx: move common linker scripts into the CPU directory
Each CPU of PowerPC has its default linker script under the CPU
directory, except mpc8xx.

Every mpc8xx board has its own linker script under the board
directory, resulting in lots of duplication of linker scripts.

I notice eight mpc8xx boards have the same linker script.
We can decrease the number of linker scripts by putting a single
default linker script, arch/powerpc/cpu/mpc8xx/u-boot.lds.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2014-09-24 18:30:27 -04:00
Ebony Zhu
07c4eea484 powerpc/mpc85xx: Serdes protocol "00" is supported
"0x00" is a valid serdes protocol for QorIQ parts, and can not be
used to test whether the serdes is enabled or disabled.

Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-24 13:10:52 -07:00
ramneek mehresh
e628c8f75d powerpc/8xxx: Fix in USB device-tree fixup
Fix following issues in USB device-tree fixup:
        - returns when either dr_mode or phy_type not defined.
          This was terminating fix-up when only either property
          was defined in hwconfig string
        - updates dr_mode_type or dr_phy_type with junk value when
          their index is -1. Now these are updated only when their
          respective index is pointing to relevant types
          in modes[] and phys[] array
        - dr_mode_type and dr_phy_type were not NULL for
          each controller

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-24 13:05:51 -07:00
Stefan Roese
75f698e51c arm: kirkwood: spi.h: Add some missing parenthesis
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:47:16 +05:30
Nitin Garg
36c1ca4d46 imx: Support i.MX6 High Assurance Boot authentication
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
2014-09-22 16:21:04 +02:00
Stefano Babic
42817eb85d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-22 15:51:01 +02:00
Albert ARIBAUD
2a8c9c86b9 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-09-21 16:56:44 +02:00
Bo Shen
abe307ddb8 ARM: atmel: add pcr related definition
Using CPU_HAS_PCR micro to present the SoC has pcr
(peripheral control register).

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:19 +02:00
Bo Shen
b24c1a10b5 ARM: atmel: use pcr to enable or disable peripheral clock
When use pcr (peripheral control register), then we won't need
to care about the peripheral ID.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:18 +02:00
Bo Shen
7b1dc26fae ARM: atmel: sama5d3: add timings register
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:17 +02:00
Murali Karicheri
6c343825dd ARM: keystone: ddr3: workaround for ddr3a/3b memory issue
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Keegan Garcia <kgarcia@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-17 21:06:56 -04:00
Tom Rini
e38b15b061 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-17 18:01:04 -04:00
Albert ARIBAUD
c292adae17 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-09-17 23:35:34 +02:00
Tom Rini
1ee30aeed4 Revert "ARM: SPL: do not set gd again"
At the high level, the problem is that we set gd multiple times (and
still do, even after the commit we're reverting).  We set important
parts of gd to the copy which is not above stack but rather in the data
section.  For the release, we're going to revert this change and for the
next release we shall correct things to only, really, set gd once to an
appropriate location and ensure that comments about it are correct too.

This reverts commit f0c3a6c4ad.

Acked-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
016a954ee9 kconfig: armv8: move CONFIG_ARM64 to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
8813fdaf4b vexpress64: kconfig: consolidate CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
We do not have to distinguish CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
from CONFIG_TARGET_VEXPRESS_AEMV8A.  Rename the former to the latter.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Cc: David Feng <fenghua@phytium.com.cn>
2014-09-16 12:24:00 -04:00
Stefano Babic
d4940fc521 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-16 16:30:11 +02:00
Andrew Ruder
816264fc66 arm: mx35: use common timer functions
This patch moves mx35 to the common timer functions added in commit

  8dfafdd - Introduce common timer functions <Rob Herring>

The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks().  get_ticks() returned a 32-bit value
cast up to a 64-bit value.  If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor.  Rather than patch the specific mx35 issues, simply
move everything over to the common code.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-16 12:53:09 +02:00
Andrew Ruder
93a0ea501e arm: mx31: use common timer functions
This patch moves mx31 to the common timer functions added in commit

  8dfafdd - Introduce common timer functions <Rob Herring>

The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks().  get_ticks() returned a 32-bit value
cast up to a 64-bit value.  If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor.  Rather than patch the specific mx31 issues, simply
move everything over to the common code.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Helmut Raiger <helmut.raiger@hale.at>
2014-09-16 12:51:46 +02:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
3174e4e812 kconfig: add CONFIG_SYS_{ARCH, CPU, ...} type def to arch/Kconfig
This commit adds the type definitions (+ help messages) of
CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} to arch/Kconfig,
which would save lots of type defs for taget boards.
(See also the next commit.)

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:50 -04:00
Tom Rini
8d028d404f Merge branch 'master' of git://git.denx.de/u-boot-dm 2014-09-13 16:32:52 -04:00
Tom Rini
114cc4290b Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-12 11:27:46 -04:00
Benoît Thébaudeau
a7f99bf139 arm: Fix _start for CONFIG_SYS_DV_NOR_BOOT_CFG
The boards using CONFIG_SYS_DV_NOR_BOOT_CFG (i.e. calimain,
da850evm_direct_nor and enbw_cmc) had the _start symbol defined after
the CONFIG_SYS_DV_NOR_BOOT_CFG word rather than before it in
arch/arm/lib/vectors.S. Because of that, if by lack of luck
'gd->mon_len = (ulong)&__bss_end - (ulong)_start' (see setup_mon_len())
was a multiple of 4 kiB (see reserve_uboot()), then the last BSS word
overlapped the first word of the following reserved RAM area (or went
beyond the top of RAM without such an area) after relocation because
__image_copy_start did not match _start (see relocate_code()).

This was broken by commit 41623c9 'arm: move exception handling out of
start.S files', which defined _start twice (before and after the
CONFIG_SYS_DV_NOR_BOOT_CFG word), then by commit 0a26e1d 'arm: fix a
double-definition error of _start symbol', which kept the definition of
the _start symbol after the CONFIG_SYS_DV_NOR_BOOT_CFG word. This new
commit fixes this issue by restoring the original behavior, i.e. by
defining the _start symbol before the CONFIG_SYS_DV_NOR_BOOT_CFG word.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
2014-09-11 18:04:39 +02:00
Benoît Thébaudeau
58f9e1ae63 arm: Make reset position-independent
Some boards, like mx31pdk and tx25, require the beginning of the SPL
code to be position-independent. For these two boards, this is because
they use the i.MX external NAND boot, which starts by executing the
first NAND Flash page from the NFC page buffer. The SPL then needs to
copy itself to its actual link address in order to free the NFC page
buffer and use it to load the non-SPL image from Flash before running
it. This means that the SPL runtime address differs from its link
address between the reset and the initial copy performed by
board_init_f(), so this part of the SPL binary must be
position-independent.

This requirement was broken by commit 41623c9 'arm: move exception
handling out of start.S files', which used an absolute address to branch
to the reset routine. This new commit restores the original behavior,
which just performed a relative branch. This fixes the boot of mx31pdk
and tx25.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Helmut Raiger <helmut.raiger@hale.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: John Rigby <jcrigby@gmail.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2014-09-11 18:04:34 +02:00
Stefano Babic
3d8f1798ba imx: Fix build of mx6sxsabresd
Commit 224beb833e add clock
enabling function for FEC, but the masks are not available
for SX processor and the mx6sxsabresd cannot be built clean.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-11 10:13:44 +02:00
Simon Glass
c369139234 tegra: dts: Add serial port details
Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.

The console alias needs to be set up to indicate which port is used for
the console.

Also add a binding file since this is missing.

Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 13:00:02 -06:00
Simon Glass
2a9ae6e02f sandbox: dts: Add a serial console node
If the sandbox device tree is provided to U-Boot (with the -d flag) then it
will use the device tree version in preference to the built-in device. The
only difference is the colour.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 13:00:00 -06:00
Simon Glass
2fccd2d96b tegra: Convert tegra GPIO driver to use driver model
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.

The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.

The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.

Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 12:59:59 -06:00
Tom Rini
b7a809957b Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2014-09-10 06:59:49 -04:00
Fabio Estevam
1b8ad74a6f pcie_imx: Add mx6solox support
Let PCI on mx6solox also be supported.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-09-09 17:24:49 +02:00
Fabio Estevam
ac17dcf653 mx6: imx-regs: Provide a structure for GPC registers
Introduce a structure for accessing the General Power Controller block (GPC)
registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-09-09 17:24:49 +02:00
Fabio Estevam
19a895cbe9 mx6qsabreauto: Remove imx6q-sabreauto.dts
Commit fa9c021632 ("mx6: add example DTB for mx6qsabreauto") introduced
'imx6q-sabreauto.dts' but it adds no real value as the dts file only contains
the 'model' and 'compatible' strings.

After this commit the final binary is also changed from 'u-boot.imx' to
'u-boot-dtb.imx', which may confuse users.

So revert it until a more complete and useful device tree could be provided.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-09-09 17:11:01 +02:00
Nikolay Dimitrov
2d59e3ecd2 mx6: Fix ECSPI typo in soc_boot_modes
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-09-09 16:47:43 +02:00
Ye.Li
4aa7ac30a7 iMX6: Disable the L2 before chaning the PL310 latency
The Latency parameters of PL310 Tag RAM latency control register and
Data RAM Latency control register are set in L2 cache enable. And
setting these registers must have PL310 NOT enabled.

But when using Plugin mode boot, the PL310 is enabled by bootrom.
The patch disables the PL310 before applying this setting.

Signed-off-by: Ye.Li <Ye.Li@freescale.com>
2014-09-09 16:30:40 +02:00
Nikita Kiryanov
e32028a70b arm: mx6: add support for Compulab cm-fx6 CoM
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:43 +02:00
Nikita Kiryanov
ea818ae748 arm: mx6: add get_cpu_type()
Define get_cpu_type(). Reuse it in is_cpu_type().

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
07ee927d2c arm: mx6: ddr: fix cs0_end calculation
Current way of calculation CS0_END field for MMDCx_MDASP register
is problematic because in most cases the user is forced to define
cs_density in an unnatural way: as value - 2, instead of value.

This breaks the abstraction provided by struct mx6_ddr_sysinfo
because the user is forced to be aware of the way the calculation
is performed.

Refactor the calculation.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
08155289a4 arm: mx6: ddr: configure MMDC for slow_pd
According to MX6 TRM, both MMDC and DRAM should be configured to
the same powerdown precharge. Currently, mx6_dram_cfg()
configures MMDC for fast pd (MDPDC[7] = 0), and the DRAM for
'slow exit (DLL off)' (MR0[12] = 0).

Configure MMDC for slow pd.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
06a51b8cc8 arm: mx6: ddr: do not write into reserved bit
Bit 16 in mapsr register is in a reserved field. Don't write to it.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
3368918f71 arm: mx6: ddr: cleanup
No functional changes.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:33:39 +02:00
Nikita Kiryanov
c6c2492ad8 i2c: imx: add macros to setup pads for multiple SoC types
Add macro which defines i2c_pads_info structs for multiple SoC types,
and a macro which selects the appropriate struct based on CPU type,
thus eliminating the need to manage multiple i2c pad configurations
manually when supporting multiple SoC types.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:32:32 +02:00
Nikita Kiryanov
224beb833e mx6: add clock enabling functions
Add functions to enable/disable clocks for UART, SPI, ENET, and MMC.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:32:32 +02:00
Jeroen Hofstee
f2cbb037a7 eabi_compat: add __aeabi_memcpy __aeabi_memset
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:51:11 +02:00
Jeroen Hofstee
c65a2abb6c ARM: make gd a function for clang
"clang does not support global register variables; this is
unlikely to be implemented soon because it requires additional
LLVM backend support" [1]

Workaround it by obtaining the value of gd/r9 by an inline
asm routine. Note there is no set routine added for ARM at the
moment, since most if not all updates of gd from c are actually
not needed for ARM.

[1] http://clang.llvm.org/docs/UsersManual.html

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:51:08 +02:00
Jeroen Hofstee
f0c3a6c4ad ARM: SPL: do not set gd again
Just before calling board_init_f, crt0.S has already
reserved space for the initial gd on the stack. There
should be no need to allocate it again.

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:50:57 +02:00
Vasili Galka
c6fcb603a2 microblaze: Fix printf size_t format related warnings (again...)
The basic idea: Define size_t using the __SIZE_TYPE__ compiler-defined
type.

For detailed explanation see similar patch for the nios2 arch:
"nios2: Fix printf size_t format related warnings (again...)"
(sha1: 00a2517fcb)

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-09-09 09:58:36 +02:00
Albert ARIBAUD
b653516769 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-09-09 00:21:24 +02:00
Wang Huan
327def5060 video: dcu: Add DCU driver support
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:35 -07:00
Wang Huan
c8a7d9dab0 arm: ls102xa: Add basic support for LS1021ATWR board
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
 One DDR controller
 DUART1 is used as the console

For the detail board information, please refer to README.

Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:35 -07:00
Wang Huan
550e3dc090 arm: ls102xa: Add basic support for LS1021AQDS board
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
 One DDR controller
 DUART1 is used as the console

For the detail board information, please refer to README.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-09-08 10:30:34 -07:00
Claudiu Manoil
93f26f130e net: Merge asm/fsl_enet.h into fsl_mdio.h
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.

To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2014-09-08 10:30:33 -07:00
Wang Huan
d60a2099a2 arm: ls102xa: Add Freescale LS102xA SoC support
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.

Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-09-08 10:30:32 -07:00
Ajay Kumar
466d40396e ARM: exynos: peach_pit: Add DT nodes for fimd and parade bridge chip
This patch adds DT properties for fimd and the parade bridge chip
present on peach_pit. The panel supports 1366x768 resolution.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
a99cea0313 exynos5420: add callbacks needed for exynos_fb driver
Add initialization code for peach_pit panel, parade bridge chip,
and backlight.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
2358fc8ed9 ARM: exynos: Add missing declaration for gpio_direction_input
This patch adds missing declaration for gpio_direction_input
function, thereby helps in resolving compilation warnings.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
45c480c9f6 video: exynos_fimd: Add framework to disable FIMD sysmmu
On Exynos5420 and newer versions, the FIMD sysmmus are in
"on state" by default.
We have to disable them in order to make FIMD DMA work.
This patch adds the required framework to exynos_fimd driver,
and disables FIMD sysmmu on Exynos5420.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
496f0e47e1 arm: exynos: Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
e6756f6a2e arm: exynos: Add RPLL for Exynos5420
RPLL is needed to drive the LCD panel on Exynos5420 based boards.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
f0017175e3 exynos_fb: Remove usage of static defines
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.

Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Przemyslaw Marczak
73eca21128 odroid: kconfig: add odroid_defconfig
This config is valid for two devices:
- Odroid X2,
- Odroid U3.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:50 +09:00
Przemyslaw Marczak
a47fa7906c odroid: add odroid U3/X2 device tree description
This is a standard description for Odroid boards.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:50 +09:00
Przemyslaw Marczak
1fb4dab2a1 arm:reset: call the reset_misc() before the cpu reset
On an Odroid U3 board, the SOC is unable to reset the eMMC card
in the DWMMC mode by the cpu software reset. Manual reset of the card
by switching proper gpio pin - fixes this issue.

Such solution needs to add a call to pre reset function.
This is done by the reset_misc() function, which is called before reset_cpu().
The function reset_misc() is a weak function.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>

Changes v4:
- arch/arm/reset: fix weak function attribute to proper style
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
Przemyslaw Marczak
4fb4d55a35 arch:exynos: boot mode: add get_boot_mode(), code cleanup
This patch introduces code clean-up for exynos boot mode check.
It includes:
- removal of typedef: boot_mode
- move the boot mode enum to arch-exynos/power.h
- add bootmode for sequence: eMMC 4.4 ch4 / SD ch2
- add new function: get_boot_mode() for OM[5:1] pin check
- update spl boot code

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>

Changes v5:
- exynos: boot mode: add missing bootmode (1st:EMMC 4.4 / 2nd:SD ch2)

Changes v6:
- none

changes v7:
- change boot mode name: BOOT_MODE_MMC to BOOT_MODE_SD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
Przemyslaw Marczak
19f1b629bf exynos: pinmux: fix the gpio names for exynos4x12 mmc
This change fixes the bad gpio configuration for the exynos dwmmc.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
R Sricharan
681f785f7c ARM: DRA72: DDR3: Add emif settings for 666MHz clock
On DRA72x, EMIF supports DDR3 upto 667MHz.
Adding the required settings for DDR3 at 666MHz and enabling it.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-09-04 13:12:49 -04:00
Khoronzhuk, Ivan
e6c9428a2f keystone2: use readl/writel functions instead of redefinition
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
2014-09-04 13:06:00 -04:00
Khoronzhuk, Ivan
1c4044ae4a ARM: keystone: clock: use correct BWADJ field mask for PASSPLLCTL0
The mask for BWADJ field of PASSPLLCTL0 register has to be 0xff, but
by mistake, here is used shift instead of mask, so correct it.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-04 13:05:57 -04:00
Tom Rini
2c19478e01 Merge branch 'master' of git://git.denx.de/u-boot-arc 2014-09-02 16:37:17 -04:00
Tom Rini
141e1faec2 Merge git://git.denx.de/u-boot-dm 2014-09-02 08:22:26 -04:00
Vasili Galka
3400655e0f mpc5xxx: Add stub implementation of cache functions
Some drivers (e.g. net/e1000) reference these functions. So, this
fixes the build of MVBC_P board.

I'm not familiar with the MPC5xxx platform, maybe a full
implementation shall be implemented instead of this stub in the
future.

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>, Marek Vasut <marex@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
2014-09-02 08:19:58 -04:00
Simon Glass
4bc9a19324 dm: sandbox: dts: Add a GPIO bank
Add a bank of GPIOs for sandbox which can be used for testing this
functionality.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-08-31 23:21:42 -06:00
Masahiro Yamada
a1263632bb mx6: tqma6: get board support back to Kconfig build system
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.

Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file.  As a result, some boards added just before
the merge were lost.

This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-08-31 12:01:04 -04:00
Tom Rini
0a64bc20f7 Merge branch 'master' of git://git.denx.de/u-boot-nios 2014-08-31 07:45:55 -04:00
Masahiro Yamada
16e16fdde2 nomadik: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
ef2b694c73 highbank: kconfig: move common settings
Move Highbank-specific settings to highbank/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <robh@kernel.org>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
22f2be7a12 orion5x: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
c338f09e96 keystone: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
6c5431ac81 omap5: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
d08215a5f1 omap4: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
3cfbcb58d3 omap3: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
3491ba6311 davinci: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
72df68cc6b exynos: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
47539e2317 kirkwood: kconfig: refactor Kconfig and defconfig
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
2014-08-30 21:21:21 -04:00
Masahiro Yamada
ad17a81c06 versatile: kconfig: move common settings
Move Versatile-specific settings to versatile/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
f40b989863 rmobile: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
ddd960e6c4 tegra: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.

Insert the Tegra SoC select menu between the arch select and the
board select.

 Architecture select
 |-- Tegra Platform (Tegra)
     |- Tegra SoC select (Tegra20 / 30 / 114 / 124)
        |- Board select

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:

  config TEGRA
          bool
          select SPL

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
44dcb4036b zynq: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").

Refactor board/xilinx/zynq/MAINTAINERS too.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
2014-08-30 21:19:32 -04:00
Benoît Thébaudeau
eeadd3fe0f arm: Add missing .vectors section to linker scripts
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 07:46:41 -04:00
Tom Rini
3f1b6bebe0 arm64: Correct passing of Linux kernel args
The Documentation/arm64/booting.txt document says that pass in x1/x2/x3
as 0 as they are reserved for future use.

Signed-off-by: Tom Rini <trini@ti.com>
2014-08-30 07:46:40 -04:00
Steve Rae
9dec5270be arm: convert Cygnus and NSP boards to Kconfig
Convert the bcm958300k and the bcm958622hr boards from "boards.cfg" to Kconfig.

Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
da1f5ac295 arm: add Cygnus and NSP boards
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
562f01a2ba arm: bcmnsp: Add bcmnsp u-architecture
Base support for the Broadcom NSP SoC.
Based on iproc-common and the SoC specific reset function.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
7986688075 arm: bcmcygnus: Add bcmcygnus u-architecture
Base support for the Broadcom Cygnus SoC.
Based on iproc-common and the SoC specific reset function.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
c4b4500910 arm: iproc: Initial commit of iproc architecture code
The iproc architecture code is present in several Broadcom
chip architectures, including Cygnus and NSP.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Stefan Agner
b0e31c7b66 arm: vf610: add NFC clock support
Add NFC (NAND Flash Controller) clock support and enable them
at board initialization time.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-08-30 07:46:40 -04:00
Stefan Agner
baa3134440 arm: vf610: add NFC pin mux
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-08-30 07:46:39 -04:00
Marek Vasut
221a49d5bd ARM: Fix overflow in MMU setup
The patch fixes a corner case where adding size to DRAM start resulted
in a value (1 << 32), which in turn overflew the u32 computation, which
resulted in 0 and it therefore prevented correct setup of the MMU tables.

The addition of DRAM bank start and it's size can end up right at the end
of the address space in the special case of a machine with enough memory.
To prevent this overflow, shift the start and size separately and add them
only after they were shifted.

Hopefully, we only have systems in tree which have DRAM size aligned to
1MiB boundary. If not, this patch would break such systems. On the other
hand, such system would be broken by design anyway.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 07:46:39 -04:00
Jiandong Zheng
2d66a0fd58 arm: bcm281xx: Add Ethernet Clock support
Enable Ethernet clock when Broadcom StarFighter2 Ethernet block
(CONFIG_BCM_SF2_ETH) is enabled.

Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:39 -04:00
Sergey Kostanbaev
0bf62d7bc4 arm: ep9315: Add .vectors section to lds and remove obsolete lds
However ep9315 don't use
interrupt vectors during startup, but _startup symbol is used inside uboot to
calculate actual monitor size.

Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
2014-08-30 07:46:38 -04:00
Pavel Machek
99b97106f3 socfpga: initialize designware ethernet
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.

Signed-off-by: Pavel Machek <pavel@denx.de>
2014-08-30 07:46:38 -04:00
Thomas Chou
c69d2e5761 nios2: link to CONFIG_SYS_MONITOR_BASE and remove text_base hook
This patch changes the link script to base at CONFIG_SYS_MONITOR_BASE.
Then we can remove the text_base hook in nios2-generic board.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-30 17:48:43 +08:00
Thomas Chou
57cfeb5140 nios2: move nios2.h to arch asm directory
The nios2.h is nios2 cpu specific, and should go arch asm
directory.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-30 17:48:43 +08:00
Thomas Chou
8645071006 nios2: divide nios2-io.h into each specific drivers and remove it
The nios2-io.h defines hardware registers and bits of several FPGA
IP cores. It could be divided in to the specific drivers, including
altera timer, altera sysid, altera uart and altera jtag uart. The
altera pio and altera spi drivers use their own hardware definitions.
The removal of nios2-io.h will help modularity and maintenance.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-30 17:48:43 +08:00
Chin Liang See
3ab019e1dc socfpga: Fix SOCFPGA build error for Altera dev kit
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-08-29 15:50:54 -04:00
Pavel Machek
51fb455f82 socfpga: fix clock manager register definition
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.

This fixes structure to match hardware.

Signed-off-by: Pavel Machek <pavel@denx.de>
2014-08-29 15:50:50 -04:00
Christian Riesch
db993fc8ec arm: include config.h in arch/arm/lib/vectors.S
config.h is required for CONFIG_SYS_DV_NOR_BOOT_CFG.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2014-08-29 15:50:43 -04:00
Jeroen Hofstee
8863aa5c98 ARM:asm:io.h use static inline
When compiling u-boot with W=1 the extern inline void for
read* is likely causing the most noise. gcc / clang will
warn there is never a actual declaration for these functions.
Instead of declaring these extern make them static inline so
it is actually declared.

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-08-29 15:50:43 -04:00
Tom Rini
6defdc0b55 Merge branch 'master' of git://git.denx.de/u-boot-ti 2014-08-29 13:47:42 -04:00
Tom Rini
7f14fb20f8 Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze 2014-08-29 11:07:35 -04:00
Tom Rini
5ddc329341 Merge branch 'master' of git://git.denx.de/u-boot-tegra 2014-08-29 11:07:10 -04:00
Tom Rini
5a1095a830 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-08-29 11:06:51 -04:00
Tom Rini
6af857c50d Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2014-08-29 11:06:26 -04:00
Tom Rini
3e1b36bd58 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-28 13:03:25 -04:00
Vasili Galka
94bcd6b0ac arc: Fix printf size_t format related warnings (again...)
The basic idea: Define size_t using the __SIZE_TYPE__ compiler-defined
type.

For detailed explanation see similar patch for the nios2 arch:
http://patchwork.ozlabs.org/patch/379938/

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
2014-08-26 17:41:58 +04:00
Lokesh Vutla
7b92252370 ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
Sricharan R
f2a1b93b5c ARM: DRA7: Enable software leveling for dra7
Currently hw leveling is enabled by default on DRA7/72.
But the hardware team suggested to use sw leveling as hw leveling
is not characterized and seen some test case failures.
So enabling sw leveling on all DRA7 platforms.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
Vitaly Andrianov
61f66fd5a8 keystone2: use EFUSE_BOOTROM information to configure PLLs
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-08-25 10:48:12 -04:00
pekon gupta
9352697aa0 board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
     SW5.1 (NAND_BOOTn) = OFF (logic-1)
     SW5.2 (NOR_BOOTn)  = ON  (logic-0) /* Active-low */
     SW5.3 (eMMC_BOOTn) = OFF (logic-1)
     SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
     SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
     SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
     SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
     SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
     SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
     SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
     SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
     SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
2014-08-25 10:48:12 -04:00
Thomas Chou
055626acba nios2: remove EPCS driver
The Altera EPCS is SPI flash. We have been using SPI flash driver
to access EPCS for years. The old EPCS driver could be removed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-24 11:28:19 +08:00
Thomas Chou
5ff10aa7e7 nios2: add generic board support
This patch implements the generic board init as described in
doc/README.generic-board.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-08-24 11:28:10 +08:00
Thomas Chou
70fbc46192 nios2: remove obsolete PCI5441 and PK1C20 boards
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-24 11:27:57 +08:00
Vasili Galka
00a2517fcb nios2: Fix printf size_t format related warnings (again...)
When compiling the current code on GCC 4.8.3, the following warnings
appear:

warning: format '%zu' expects argument of type 'size_t', but argument
2 has type 'long unsigned int' [-Wformat=]

There were many mails about such warnings on different architectures.
This patch limits itself to the nios2 architecture.

The problem is that for the size_t (%zu, %zd, ...) arguments of
printf GCC does not verify the type match to size_t type. It verifies
the type match to the compiler-defined __SIZE_TYPE__ type. Thus, if
size_t is defined different from __SIZE_TYPE__ - warnings inevitably
appear.

There is a comment by Thomas Chou to the (rejected) patch:
http://patchwork.ozlabs.org/patch/272102/
which explains that the older GCC toolchains (gcc-3.4.6 and gcc-4.1.2)
expect size_t to be "unsigned long" and the newer expect it to be
"unsigned int". Thus, no matter how we define size_t - either way
warnings appear when using some GCC version.

By rejecting that patch, a choice was made to prefer older GCC versions
and leave the warnings when building with the newer toolchains.
Personally, I disagree with this choice...

In any case, this patch proposes a way to fix the warnings for any GCC
version. Just define size_t using the __SIZE_TYPE__ compiler-defined
type and the type verification will pass.

I tested that this fixes the warning on GCC 4.8.3. I don't have an
older toolchain to test with, but __SIZE_TYPE__ was definitely defined
in GCC 3.4.6, so it should work there too.

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2014-08-24 11:27:31 +08:00
Masahiro Yamada
aec6f8c59f powerpc: mpc8xx: remove FLAGADM board support
This board has been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
6bde1ec10f powerpc: mpc8xx: remove GEN860T, GEN806T_SC board support
These boards have been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
4723ce49e5 powerpc: mpc8xx: remove SXNI855T board support
This board has been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
d1a4aafd71 powerpc: mpc8xx: remove svm_sc8xx board
This board has been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
0ace4d9d8f powerpc: mpc8xx: remove stxxtc board support
This board has been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
62d636aa2a omap: remove omap5912osk board support
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.

Tom suggested to remove this board.

Remove also omap1510_udc.c because this is the last board
to enable it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
2014-08-21 12:01:12 -04:00
Tom Rini
67ee22b068 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-08-20 16:07:34 -04:00
Shaveta Leekha
390619ddb3 powerpc/mpc85xx: Enabling CPC conditionally based on hwconfig options
If hwconfig does not contains "en_cpc" then by default all cpcs are enabled
If this config is defined then only those individual cpcs which are defined
in the subargument of "en_cpc" will be enabled e.g en_cpc:cpc1,cpc2; (this
will enable cpc1 and cpc2) or en_cpc:cpc2; (this enables just cpc2)

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-20 10:44:15 -07:00
Fabio Estevam
d145878d59 mx6sxsabresd: Add Ethernet support
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.

Add support for one FEC port initially.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:15:23 +02:00
Fabio Estevam
5c045cddaa mx6sx: Adjust enable_fec_anatop_clock() for mx6solox
Configure and enable the ethernet clock for mx6solox.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:14:09 +02:00
Fabio Estevam
080d72f233 mx6sxsabresd: Convert to the new Kconfig style
mx6sxsabresd was not in the master branch when the conversion to the new Kconfig
style happened, so convert it now so that it can build again.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:11:12 +02:00
Marek Vasut
b299ab7435 ARM: mx6: Handle the MMDCx_MDCTL COL field caprices
The COL field value cannot be easily calculated from the desired
column number. Instead, there are special cases for that, see the
datasheet, MMDCx_MDCTL field description, field COL . Cater for
those special cases.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-08-20 12:22:52 +02:00
Marek Vasut
fcfdfdd58c ARM: mx6: Prevent overflow in DRAM size detection
The MX6 DRAM controller can be configured to handle 4GiB of DRAM, but
only 3840 MiB of that can be really used. In case the controller is
configured to operate a 4GiB module, the imx_ddr_size() function will
correctly compute that there is 4GiB of DRAM in the system. Firstly,
the return value is 32-bit, so the function will effectively return
zero. Secondly, the MX6 cannot address the full 4GiB, but only 3840MiB
of all that. Thus, clamp the returned size to 3840MiB in such case.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2014-08-20 12:21:57 +02:00
Marek Vasut
68968901e7 ARM: mx5: Fix CHSCCDR name
Fix the name of the CCM CHSCCDR register.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-08-20 12:19:20 +02:00
Gabriel Huau
a76df70908 mx6: add support of multi-processor command
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.

Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-08-20 11:52:54 +02:00
Michal Simek
ae2ee77f98 ARM: zynq: Remove spl.h
Do not specify own zynq specific SPL macros
because there is no need for that.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-19 08:48:18 +02:00
Michal Simek
dbc31f6a20 ARM: zynq: Move ps7_init() out of spl.h
Prepare for spl.h removal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-19 08:48:00 +02:00
Stefan Agner
24d4d422c1 ARM: tegra: add Colibri T30 board support
This adds board support for the Toradex Colibri T30 module.

Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:59:04 -07:00
Stephen Warren
aeb3fcb359 ARM: tegra: Use mem size from MC rather than ODMDATA
In at least Tegra124, the Tegra memory controller (MC) has a register
that controls the memory size. Read this to determine the memory size
rather than requiring this to be redundantly encoded into the ODMDATA.
This way, changes to the BCT (i.e. MC configuration) automatically
updated SW's view of the memory size, without requiring manual changes
to the ODMDATA.

Future work potentially required:
* Clip the memory size to architectural limits; U-Boot probably doesn't
  and won't support either LPAE or Tegra's "swiss cheese" memory layout,
  at least one of which would be required for >2GB RAM.
* Subtract out any carveout required by firmware on future SoCs.

Based-on-work-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:57:03 -07:00
Bryan Wu
df3443dfa4 ARM: tegra: Disable VPR
On Tegra114 and Tegra124 platforms, certain display-related registers cannot
be accessed unless the VPR registers are programmed.  For bootloader, we
probably don't care about VPR, so we disable it (which counts as programming
it, and allows those display-related registers to be accessed).

This patch is based on the commit 5f499646c83ba08079f3fdff6591f638a0ce4c0c
in Chromium OS U-Boot project.

Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[acourbot: ensure write went through, vpr.c style changes]
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:57:02 -07:00
Stefano Babic
7e9291720d Update aristainetos board to Kconfig
aristainetos board was merged in u-boot-imx before
Kconfig was integrated, but it is not yet
mainline.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2014-08-13 09:30:41 +02:00
Tom Rini
5b7d0027c2 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2014-08-12 16:54:55 -04:00
Tang Yuantian
ce249d956c powerpc/t104xrdb: support deep sleep in SPI/SD boot
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.

Entry point to kernel is still placed in second stage uboot.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-12 12:26:47 -07:00
Tang Yuantian
3067547502 powerpc/mpc85xx: Make boot flag effective
bootflag as a parameter is passed to board_init_f().
But it is not actually used in this function.
Make it effective by assigned it to gd->flags.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-12 12:26:47 -07:00
Siarhei Siamashka
bf4ca384ad sunxi: dram: Autodetect DDR3 bus width and density
In the case if the 'dram_para' struct does not specify the exact bus
width or chip density, just use a trial and error method to find a
usable configuration.

Because all the major bugs in the DRAM initialization sequence are
now hopefully fixed, it should be safe to re-initialize the DRAM
controller multiple times until we get it configured right. The
original Allwinner's boot0 bootloader also used a similar
autodetection trick.

The DDR3 spec contains the package pinout and addressing table for
different possible chip densities. It appears to be impossible to
distinguish between a single chip with 16 I/O data lines and a pair
of chips with 8 I/O data lines in the case if they provide the same
storage capacity. Because a single 16-bit chip has a higher density
than a pair of equivalent 8-bit chips, it has stricter refresh timings.
So in the case of doubt, we assume that 16-bit chips are used.
Additionally, only Allwinner A20 has all A0-A15 address lines and
can support densities up to 8192. The older Allwinner A10 and
Allwinner A13 can only support densities up to 4096.

We deliberately leave out DDR2, dual-rank configurations and the
special case of a 8-bit chip with density 8192. None of these
configurations seem to have been ever used in real devices. And no
new devices are likely to use these exotic configurations (because
only up to 2GB of RAM can be populated in any case).

This DRAM autodetection feature potentially allows to have a single
low performance fail-safe DDR3 initialiazation for a universal single
bootloader binary, which can be compatible with all Allwinner
A10/A13/A20 based devices (if the ifdefs are replaced with a runtime
SoC type detection).

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:34 +02:00
Siarhei Siamashka
935758b1d5 sunxi: dram: Derive write recovery delay from DRAM clock speed
The write recovery time is 15ns for all JEDEC DDR3 speed bins. And
instead of hardcoding it to 10 cycles, it is possible to set tighter
timings based on accurate calculations. For example, DRAM clock
frequencies up to 533MHz need only 8 cycles for write recovery.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
b5c71f5f9c sunxi: dram: Drop DDR2 support and assume only single rank DDR3 memory
All the known Allwinner A10/A13/A20 devices are using just single rank
DDR3 memory. So don't pretend that we support DDR2 or more than one
rank, because nobody could ever test these configurations for real and
they are likely broken. Support for these features can be added back
in the case if such hardware actually exists.

As part of this code cleanup, also replace division by 1024 with
division by 1000 for the refresh timing calculations. This allows
to use the original non-skewed tRFC timing table from the DRR3 spec
and make code less confusing.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
d755a5fb20 sunxi: dram: Configurable DQS gating window mode and delay
The hardware DQS gate training is a bit unreliable and does not
always find the best delay settings.

So we introduce a 32-bit 'dqs_gating_delay' variable, where each
byte encodes the DQS gating delay for each byte lane. The delay
granularity is 1/4 cycle.

Also we allow to enable the active DQS gating window mode, which
works better than the passive mode in practice. The DDR3 spec
says that there is a 0.9 cycles preamble and 0.3 cycle postamble.
The DQS window has to be opened during preamble and closed during
postamble. In the passive window mode, the gating window is opened
and closed by just using the gating delay settings. And because
of the 1/4 cycle delay granularity, accurately hitting the 0.3
cycle long postamble is a bit tough. In the active window mode,
the gating window is auto-closing with the help of monitoring
the DQS line, which relaxes the gating delay accuracy requirements.

But the hardware DQS gate training is still performed in the passive
window mode. It is a more strict test, which is reducing the results
variance compared to the training with active window mode.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
e044daa33e sunxi: dram: Add a helper function 'mctl_get_number_of_lanes'
It is going to be useful in more than one place.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
b8f7cb6ae3 sunxi: dram: Improve DQS gate data training error handling
The stale error status should be cleared for all sun4i/sun5i/sun7i
hardware and not just for sun7i. Also there are two types of DQS
gate training errors ("found no result" and "found more than one
possible result"). Both are handled now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
013f2d7469 sunxi: dram: Use divisor P=1 for PLL5
This configures the PLL5P clock frequency to something in the ballpark
of 1GHz and allows more choices for MBUS and G2D clock frequency
selection (using their own divisors). In particular, it enables the use
of 2/3 clock speed ratio between MBUS and DRAM.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
1a9717cbb3 sunxi: dram: Configurable MBUS clock speed (use PLL5 or PLL6)
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
    http://linux-sunxi.org/A10_DRAM_Controller_Performance

This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.

PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.

Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
5c18384dea sunxi: dram: Re-introduce the impedance calibration ond ODT
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:

    http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0

The new code supports both of the impedance configuration modes:
   - If the higher bits of the 'zq' parameter in the 'dram_para' struct
     are zero, then the lowest 8 bits are used as the ZPROG value, where
     two divisors encoded in lower and higher 4 bits. One divisor is
     used for calibrating the termination impedance, and another is used
     for the output impedance.
   - If bits 27:8 in the 'zq' parameters are non-zero, then they are
     used as the pre-defined ZDATA value instead of performing the ZQ
     calibration.

Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
94cd301988 sunxi: dram: Add 'await_bits_clear'/'await_bits_set' helper functions
The old 'await_completion' function is not sufficient, because
in some cases we want to wait for bits to be cleared, and in the
other cases we want to wait for bits to be set. So split the
'await_completion' into two new 'await_bits_clear' and
'await_bits_set' functions.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
cfc89b003b sunxi: dram: Do DDR3 reset in the same way on sun4i/sun5i/sun7i
The older differences were likely justified by the need to mitigate
the CKE delay timing violations on sun4i/sun5i. The CKE problem is
already resolved, so now we can use the sun7i variant of this code
everywhere.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
7e40e1926a sunxi: dram: Remove broken impedance and ODT configuration code
We can safely remove it, because none of the currently supported
boards uses these features.

The existing implementation had multiple problems:
   - unnecessary code duplication between sun4i/sun5i/sun7i
   - ZQ calibration was never initiated explicitly, and could be
     only triggered by setting the highest bit in the 'zq' parameter
     in the 'dram_para' struct (this was never actually done for
     any of the known Allwinner devices).
   - even if the ZQ calibration could be started, no attempts were
     made to wait for its completion, or checking whether the
     default automatically initiated ZQ calibration is still
     in progress
   - ODT was only ever enabled on sun4i, but not on sun5i/sun7i

Additionally, SDR_IOCR was set to 0x00cc0000 only on sun4i. There
are some hints in the Rockchip Linux kernel sources, indicating
that these bits are related to the automatic I/O power down
feature, which is poorly understood on sunxi hardware at the
moment. Avoiding to set these bits on sun4i too does not seem to
have any measurable/visible impact.

The impedance and ODT configuration code will be re-introdeced in
one of the next comits.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
f8e88b6837 sunxi: dram: Fix CKE delay handling for sun4i/sun5i
Before driving the CKE pin (Clock Enable) high, the DDR3 spec requires
to wait for additional 500 us after the RESET pin is de-asserted.

The DRAM controller takes care of this delay by itself, using a
configurable counter in the SDR_IDCR register. This works in the same
way on sun4i/sun5i/sun7i hardware (even the default register value
0x00c80064 is identical). Except that the counter is ticking a bit
slower on sun7i (3 DRAM clock cycles instead of 2), resulting in
longer actual delays for the same settings.

This patch configures the SDR_IDCR register for all sun4i/sun5i/sun7i
SoC variants and not just for sun7i alone. Also an explicit udelay(500)
is added immediately after DDR3 reset for extra safety. This is a
duplicated functionality. But since we don't have perfect documentation,
it may be reasonable to play safe. Half a millisecond boot time increase
is not that significant. Boot time can be always optimized later.
Preferebly by the people, who have the hardware equipment to check the
actual signals on the RESET and CKE lines and verify all the timings.

The old code did not configure the SDR_IDCR register for sun4i/sun5i,
but performed the DDR3 reset very early for sun4i/sun5i. This resulted
in a larger time gap between the DDR3 reset and the DDR3 initialization
steps and reduced the chances of CKE delay timing violation to cause
real troubles.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
e626d2d446 sunxi: dram: Respect the DDR3 reset timing requirements
The RESET pin needs to be kept low for at least 200 us according
to the DDR3 spec. So just do it the right way.

This issue did not cause any visible major problems earlier, because
the DRAM RESET pin is usually already low after the board reset. And
the time gap before reaching the sunxi u-boot DRAM initialization
code appeared to be sufficient.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
f257796773 sunxi: dram: Remove broken super-standby remnants
If the dram->ppwrsctl (SDR_DPCR) register has the lowest bit set to 1,
this means that DRAM is currently in self-refresh mode and retaining the
old data. Since we have no idea what to do in this situation yet, just
set this register to 0 and initialize DRAM in the same way as on any
normal reboot (discarding whatever was stored there).

This part of code was apparently used by the Allwinner boot0 bootloader
to handle resume from the so-called super-standby mode. But this
particular code got somehow mangled on the way from the boot0 bootloader
to the u-boot-sunxi bootloader and has no chance of doing anything even
remotely sane. For example:
1. in the original boot0 code we had "mctl_write_w(SDR_DPCR,
   0x16510000)" (write to the register) and in the u-boot it now looks
   like "setbits_le32(&dram->ppwrsctl, 0x16510000)" (set bits in the
   register)
2. in the original boot0 code it was issuing three commands "0x12, 0x17,
   0x13" (Self-Refresh entry, Self-Refresh exit, Refresh), but in the
   u-boot they have become "0x12, 0x12, 0x13" (Self-Refresh entry,
   Self-Refresh entry, Refresh)

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
34759d74a3 sunxi: dram: Remove useless 'dramc_scan_dll_para()' function
The attempt to do DRAM parameters calibration in 'dramc_scan_dll_para()'
function by trying different DLL adjustments and using the hardware
DQS gate training result as a feedback is a great source of inspiration,
but it just can't work properly the way it is implemented now. The fatal
problem of this implementation is that the DQS gating window can be
successfully found for almost every DLL delay adjustment setup that
gets tried. Thus making it unable to see any real difference between
'good' and 'bad' settings.

Also this code was supposed to be only activated by setting the highest
bit in the 'dram_tpr3' variable of the 'dram_para' struct (per-board
dram configuration). But none of the linux-sunxi devices has ever used
it for real. Basically, this code is just a dead weight.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Stefano Babic
e82abaeb7f Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-08-11 10:21:03 +02:00
maxin.john@enea.com
194c1ed400 emif.h: remove duplicated argument to |
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).

Signed-off-by: Maxin B. John <maxin.john@enea.com>
2014-08-09 11:17:03 -04:00
Albert ARIBAUD
1899fac925 Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-08-09 16:48:34 +02:00
Peter Crosthwaite
fb8d876698 zynq: spl: Add vectors section to linker script
The vectors section contains the _start symbol which is used as the
program entry point. Add it to the linker script in same fashion as done
for regular u-boot. This allows for correct generation of an spl elf
with a non-zero entry point.

A similar change was applied to sunxi platform in
"sunxi: Fix u-boot-spl.lds to refer to .vectors"
(sha1: 9e5f80d823)

This also allows for placement of the vector table at the hivecs
location by setting the TEXT_BASE to 0xffff0000.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-08-08 11:27:29 +02:00
Fabio Estevam
9cd744ff11 mx6: crm_regs: Fix MXC_CCM_CIMR_MASK_PERIPH2_CLK_SEL_LOADED
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
326454a88d mx6: crm_regs: Fix MXC_CCM_CLPCR_WB_PER_AT_LPM definition
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
338c9da605 mx6: crm_regs: Fix CDCDR_SPDIF0_CLK_PODF mask and offset
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
2834490245 mx6: imx-regs: Remove unused 'omux' field from iomux struct
'omux' field is not used anywhere and such layout is not valid for mx6solox.

Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-08-08 10:29:39 +02:00
Stefano Babic
c23154aab5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-08 10:18:40 +02:00
Sonic Zhang
c49eabeffc blackfin: convert blackfin board_f and board_r to use generic board init functions
- move blackfin specific cpu init code from blackfin board.c to cpu.c
- remove blackfin specific board init code and invoke generic board_f fron cpu init entry
- rename section name bss_vma to bss_start in order to match the generic board init code
- add a fake relocate_code function to set up the new stack only

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-08-07 15:15:14 +08:00
Scott Jiang
9f9a65c80a blackfin: spi clock is in sysclk1 domain instead of sysclk0
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-08-07 15:15:09 +08:00
Aaron Wu
08b6a61162 bfin: add register define required by core B on dual core BF609 processor
Add register define required by core B on dual core BF609 processor.

Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
2014-08-07 15:15:08 +08:00
Tom Rini
dcdb61a084 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-08-06 08:38:18 -04:00
Tom Rini
aa159e681e Merge http://git.denx.de/u-boot-dm 2014-08-04 10:16:27 -04:00
Simon Glass
76a1e584e1 arm: Support pre-relocation malloc()
Add support for re-relocation malloc() in arm's start-up code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-08-04 05:24:35 -06:00
Simon Glass
aae2aef9c8 arm: Set up global data before board_init_f()
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.

If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.

Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
2014-08-04 05:23:59 -06:00
Boschung, Rainer
919e05520f powerpc: mpc85xx watchdog init added to init_func
When CONFIG_WATCHDOG is defined the board initialization just performs
a WATCHDOG_RESET, an initialization of the watchdog is not done.
This has been modified fot the MPC85xx, the board initialization calls
its watchdog initialitzation allowing for full watchdog configuration
very early in the boot phase.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:28 -07:00
Boschung, Rainer
0f8062b25b mpc85xx: watchdog initialisation added
Function to inititialize the cpu watchdog added.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
[York Sun: Add prototype in watchdog.h]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:17 -07:00
Boschung, Rainer
60b295672d powerpc: macros for e500mc timer regs added
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.

The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):

watchdog_period = 1/fTB * 2^x

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:07 -07:00
Boschung, Rainer
3345d18d5b mpc85xx: fix interrupt init to not affect watchdog
TCR watchdog bit are overwritten when dec interrupt is enabled.
This has been fixed with this patch.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:17:44 -07:00
Marek Vasut
dae0f5c644 mmc: s3c: Add SD driver
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 19:24:34 +03:00
Marek Vasut
7eca6b6327 arm: s3c: Unify the S3C24xx SDI structure
Unify the register structure so they can be easily used across all
of S3C24xx lineup.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 19:24:23 +03:00
DrEagle
3fe3b4fb1c ARM: kirkwood: add mvsdio driver
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.

Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 18:44:56 +03:00
Marc Zyngier
d5db7024aa sunxi: HYP/non-sec: add sun7i PSCI backend
So far, only supporting the CPU_ON method.
Other functions can be added later.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:24 +02:00
Hans de Goede
fc70300136 sunxi: Add CONFIG_MACPWR option
On some boards the ethernet-phy needs to be powered up through a gpio,
add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-31 15:37:23 +02:00
Roman Byshko
06cdd94077 sunxi: add defines to control USB Host clocks/resets
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Ian Campbell
a6e50a88d8 ahci: provide sunxi SATA driver using AHCI platform framework
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port.  This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Masahiro Yamada
c6d12624ae powerpc: remove redundant CPU definition
CONFIG_${CPU} is defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
2014-07-30 14:42:03 -04:00
Masahiro Yamada
90f984e397 kconfig: delete redundant CONFIG_${ARCH} definition
CONFIG_${ARCH} is defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:02 -04:00
Masahiro Yamada
51148790f2 kconfig: switch to Kconfig
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.

Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.

Usage:

Run "make <board>_defconfig" to do the board configuration.

It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.

You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.

Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.

The generic syntax of configuration targets for SPL, TPL is:

  <target_image>/<config_command>

Here, <target_image> is either 'spl' or 'tpl'
      <config_command> is 'config', 'menuconfig', 'xconfig', etc.

When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)

For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.

By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.

Prior to Kconfig, we used C headers to define a set of configs.

We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.

In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:03 -04:00
Masahiro Yamada
516312598a kconfig: add basic Kconfig files
This commit adds more Kconfig files, which were written by hand.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:02 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Tom Rini
362f16b1e9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-07-29 09:41:35 -04:00
Tom Rini
302e609fe6 Merge git://www.denx.de/git/u-boot-ppc4xx 2014-07-28 17:48:48 -04:00
Tom Rini
d5f8a6ddd4 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-07-28 14:54:29 -04:00
Marc Zyngier
9d195a5461 ARM: HYP/non-sec: remove MIDR check to validate CBAR
Having a form of whitelist to check if we know of a CPU core
and and obtain CBAR is a bit silly.

It doesn't scale (how about A12, A17, as well as other I don't know
about?), and is actually a property of the SoC, not the core.

So either it works and everybody is happy, or it doesn't and
the u-boot port to this SoC is providing the real address via
a configuration option.

The result of the above is that this code doesn't need to exist,
is thus forcefully removed.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:55 +02:00
Marc Zyngier
e771a3d538 ARM: HYP/non-sec/PSCI: emit DT nodes
Generate the PSCI node in the device tree.

Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:52 +02:00
Ma Haijun
e29607ed97 ARM: convert arch_fixup_memory_node to a generic FDT fixup function
Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.

[maz: collapsed 3 patches into one, rewrote commit message]

Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:49 +02:00
Marc Zyngier
38510a4b34 ARM: HYP/non-sec: add the option for a second-stage monitor
Allow the switch to a second stage secure monitor just before
switching to non-secure.

This allows a resident piece of firmware to be active once the
kernel has been entered (the u-boot monitor is dead anyway,
its pages being reused).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:26 +02:00
Marc Zyngier
ecf07a7930 ARM: HYP/non-sec: add generic ARMv7 PSCI code
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:18 +02:00
Marc Zyngier
f510aeae68 ARM: HYP/non-sec: allow relocation to secure RAM
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.

This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
  before entering the payload
- performing an exception return from secure mode directly into
  the payload
- allowing the code to be dynamically relocated to secure RAM
  before switching to non-secure.

This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:09 +02:00
Marc Zyngier
bf433afd60 ARM: HYP/non-sec: add separate section for secure code
In anticipation of refactoring the HYP/non-secure code to run
from secure RAM, add a new linker section that will contain that
code.

Nothing is using it just yet.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:07:23 +02:00
Marc Zyngier
b726d22da9 ARM: add missing HYP mode constant
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.

Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:35 +02:00
Marc Zyngier
64fd44dcae ARM: non-sec: reset CNTVOFF to zero
Before switching to non-secure, make sure that CNTVOFF is set
to zero on all CPUs. Otherwise, kernel running in non-secure
without HYP enabled (hence using virtual timers) may observe
timers that are not synchronized, effectively seeing time
going backward...

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:28 +02:00
Marc Zyngier
800c83522c ARM: HYP/non-sec: add a barrier after setting SCR.NS==1
A CP15 instruction execution can be reordered, requiring an
isb to be sure it is executed in program order.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:19 +02:00
Marc Zyngier
c19e0dd741 ARM: HYP/non-sec: move switch to non-sec to the last boot phase
Having the switch to non-secure in the "prep" phase is causing
all kind of troubles, as that stage can be called multiple times.

Instead, move the switch to non-secure to the last possible phase,
when there is no turning back anymore.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:05:59 +02:00
Albert ARIBAUD
b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Albert ARIBAUD
48b3ed217f Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2014-07-28 10:54:54 +02:00
Albert ARIBAUD
740f41d3cb Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-07-28 10:12:45 +02:00
Albert ARIBAUD
f2c8d7f591 Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-07-26 14:08:36 +02:00
pekon gupta
222a3113b4 ARM: omap: clean redundant PISMO_xx macros used in OMAP3
PISMO_xx macros were used to define 'Platform Independent Storage MOdule'
related GPMC configurations. This patch
- Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided
  by current u-boot infrastructure.
- Removes unused redundant macros, which are no longer required after
  merging of common platform code in following commit
      commit a0a37183bd
      ARM: omap: merge GPMC initialization code for all platform

+-----------------+-----------------------------------------------------------+
| Macro           | Reason for removal                                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE                         |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE                      |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so     |
|                 | configuring GPMC chip-select for smallest allowable       |
|                 | segment (GPMC_SIZE_16M) is enough.                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of    |
|                 | 128MB (GPMC_SIZE_128M)                                    |
+-----------------+-----------------------------------------------------------+
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR      |  Unused Macros                                            |
| PISMO1_NAND     |                                                           |
| PISMO2_CS0      |                                                           |
| PISMO2_CS1      |                                                           |
| PISMO1_ONENAND  |                                                           |
| PISMO2_NAND_CS0 |                                                           |
| PISMO2_NAND_CS1 |                                                           |
| PISMO1_NOR_BASE |                                                           |
| PISMO1_NAND_BASE|                                                           |
| PISMO2_CS0_BASE |                                                           |
+-----------------+-----------------------------------------------------------+

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta
77cd89e755 ARM: omap: fix GPMC address-map size for NAND and NOR devices
Fixes commit a0a37183bd
    ARM: omap: merge GPMC initialization code for all platform

1) NAND device are not directly memory-mapped to CPU address-space, they are
 indirectly accessed via following GPMC registers:
 - GPMC_NAND_COMMAND_x
 - GPMC_NAND_ADDRESS_x
 - GPMC_NAND_DATA_x
 Therefore from CPU's point of view, NAND address-map can be limited to just
 above register addresses. But GPMC chip-select address-map can be configured
 in granularity of 16MB only.
 So this patch uses GPMC_SIZE_16M for all NAND devices.

2) NOR device are directly memory-mapped to CPU address-space, so its
 address-map size depends on actual addressable region in NOR FLASH device.
 So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
 size configuration.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
Rajendra Nayak
8c16dd6fa7 ARM: OMAP: Fix handling of errata i727
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
a906847966 board: k2e-evm: add board support
This patch adds Keystone2 k2e_evm evaluation board support.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Khoronzhuk, Ivan
1284246eb9 ARM: keystone2: spl: add K2E SoC support
Keystone2 K2E SoC has slightly different spl pll settings then
K2HK, so correct this.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
20187fd11c ARM: keystone2: add MSMC cache coherency support for K2E SOC
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
4dca7f0acc ARM: keystone2: clock: add K2E clock support
This patch adds clock definitions and commands to support Keystone2
K2E SOC.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
5c76f78858 ARM: keystone2: add K2E SoC hardware definitions
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Khoronzhuk, Ivan
8dfc15f56c ARM: keystone: clock: move K2HK SoC dependent code in separate file
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan
3d31538625 k2hk: use common KS2_ prefix for all hardware definitions
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.

Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
7b26c1f608 keystone2: add possibility to turn off all dsps
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
4984bce41f keystone2: move cpu_to_bus() to keystone.c
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan
35c547c2bc ARM: keystone2: keystone_nav: make it dependent on keystone driver
This driver is needed in case if keystone driver is used.
Currently only keystone_net driver uses it. So to avoid
redundant code compilation make the keystone_nav dependent
on keystone net driver. It also leads to compilation errors
for boards that does't use it.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00