The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
M5271 dynamic clock multiplier. It is currently fixed at 100MHz.
Allow the board header file to set their own multiplier and divider.
Added the #define for the multiplier and divider to the cpu header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Discontinue the use of CONFIG_SYS_FECI2C (only used by M5271EVB).
Use read-modify-write to activate the FEC pins without disabling I2C.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Added the CONFIG_M5271 to the list of Coldfire V2 processor. This
was causing the bus clock (not CPU clock) to be declared twice as
fast as it actually is. This causes UARTS to operate at half the
specified baudrate.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
On some platforms PCIE support is not required, but would be included
because the cpu supports it. To reduce fooprint it is now configurable
via CONFIG_PCI_DISABLE_PCIE.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the fdt UART clock fixup code to
only touch CPU internal UARTs on 4xx systems.
Only these UARTs are definitely clocked by gd->uart_clk.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, booting over the UART required the baud rate to be known ahead
of time. Using a bit of tricky simple math, we can calculate the new board
rate based on the old divisors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Newer Blackfin boot roms support using the fast SPI read command rather than
just the slow one. If the functionality is available, then use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some bits of the DDR MMRs should not be set. If they do, bad things may
happen (like random failures or hardware destruction).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin's have an on-chip rom with a syscontrol() function that needs
to be used to properly program the memory and voltage settings as it will
include (possibly critical) factory tested bias values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Take the cache flush functions from the kernel as they use hardware loops in
order to get optimal performance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start building all Blackfin boards with -ffunction-sections/-fdata-sections
and linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Some devices have no UART device pulled out, so allow people to disable the
driver completely in favor of other methods (like JTAG-console).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin JTAG has the ability to pass data via a back-channel without
halting the processor. Utilize that channel to emulate a console.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we save the value of RETX at power on and then pass it on to the
kernel so that it can nicely debug a "double-fault-caused-a-reset" crash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
People often ask questions about the init process and when things go
from flash to relocated base, so clarify the comments a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As pointed out by Ivan Koryakovskiy, the initialization code was not
actually respecting the CONFIG_CLKIN_HALF option when configuring the
PLL_CTL register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Our dcache invalidate function doesn't just invalidate, it also flushes.
So rename the function accordingly and fix the dma_memcpy() function so it
doesn't inadvertently corrupt the data destination.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds flush_/invalidate_dcache_range() to the MIPS architecture.
Those functions are needed for the upcoming dcache support for the USB
EHCI driver. I chose this API because those cache handling functions are
already present in the PPC architecture.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Added support for a second memory bank to DDR autodetection for 440
platforms.
Made hardcoded values configurable.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This change is needed for mgcoge because it uses two ethernet drivers.
Add a check for the presence of the PIGGY board on mgcoge. Without this
board networking cannot work and the initialization must be aborted.
Only allocate rtx once to prevent DPRAM exhaustion.
Initialize ether_scc.c and the keymile-specific HDLC driver (to be added
soon) in eth.c.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reset function specific to AMD SC520 microcontroller - Is more of a
'hard reset' that the triple fault.
Requires CONFIG_SYS_RESET_SC520 to be defined in config
I would have liked to add this to a new file (cpu/i386/sc520/reset.c)
but ld requires that a object file in a library arhive MUST contain
at least one function which does not override a weak function (and is
called from outside the object file) in order for that object file to
be extracted from the archive. This would be the only function on the
new file, and hence, will never get linked in.
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Moved from interrupts.c to cpu.c and made into a weak function to
allow vendor specific override
Vendor specific CPU reset (like the AMD SC520 MMCR reset) can now be
added to the vendor specific code without the need to remember to
#undef usage of the generic method and if you forget to include your
custom reset method, you will always get the default.
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Brings i386 in line with other CPUs with a reset vector and frees up reset.c
for CPU reset functions
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
This patch updates e500 freqProcessor to array based on CONFIG_NUM_CPUS,
and prints each CPU's frequency separately. It also fixes up each CPU's
frequency in "clock-frequency" of fdt blob.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
For light loaded system, we use the 1T timing to gain better
memory performance, but for some heavily loaded system,
you have to add the 2T timing options to board files.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Some 85xx processors have the advanced power management feature,
such as wake up ARP, that needs enable the automatic self refresh.
If the DDR controller pass the SR_IT (self refresh idle threshold)
idle cycles, it will automatically enter self refresh. However,
anytime one transaction is issued to the DDR controller, it will
reset the counter and exit self refresh state.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
- The DDR3 controller is expanding the bits for timing config
- Add the DDR3 32-bit bus mode support
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
According to the latest 8572 UM, the DDR3 controller
is expanding the bit mask, and we use the extend ACTTOPRE
mode when tRAS more than 19 MCLK.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
This ensures that subsequent accesses properly hit the new window.
The dcbi during the NAND loop was accidentally working around this;
it's no longer necessary, as the cache is not enabled.
Reported-by: Suchit Lepcha <Suchit.Lepcha@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for MPC83xx PCI-E controllers in Root Complex
mode.
The patch is based on Tony Li and Dave Liu work[1].
Though unlike the original patch, by default we don't register PCI-E
buses for use in U-Boot, we only configure the controllers for future
use in other OSes (Linux). This is done because we don't have enough
of spare BATs to map all the PCI-E regions.
To actually use PCI-E in U-Boot, users should explicitly define
CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES symbol in the board file. And
only then U-Boot will able to access PCI-E, but at the cost of disabled
address translation.
[1] http://lists.denx.de/pipermail/u-boot/2008-January/027630.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running a system with 2 or more MPC8349EMDS boards in PCI agent mode,
the boards will lock up the PCI bus by scanning against each other.
The boards lock against each other by trying to access the PCI bus before
clearing their configuration lock bit. Both boards end up in a loop,
sending and receiving "Target Not Ready" messages forever.
When running in PCI agent mode, the scanning now takes place after the
boards have cleared their configuration lock bit.
Also, add a missing declaration to the mpc83xx.h header file, fixing a
build warning.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently there are in excess of 100 bytes located at the beginning of the image
built by start.S that are not being utilized. This patch moves a few functions
into this part of the image. This will create a greater number of *available*
bytes that can be used by board specific code in NAND builds and will decrease
the size of the assembled code in other builds.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Parallel builds would occasionally issue this build warning:
ln: creating symbolic link `cpu/mpc824x/bedbug_603e.c': File exists
Use "ln -sf" as quick work around for the issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
So that we can locate the DDR tlb start entry to the value other than 8. By
default, it is still 8.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency
and print it out, but don't save it.
This changes where its calculated and stored to be more consistent with the
CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock.
The localbus frequency is added to sysinfo and calculated when sysinfo is
set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are.
get_clocks() copies the frequency into the global data, as the other
frequencies are, into a new field that is only enabled for MPC85xx and
MPC86xx.
checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency
from sysinfo, like the other frequencies, instead of calculating it on the
spot.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
The local bus clock divider should be doubled for both 8610 and 8641.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
The clock divider for the MPC8568 local bus should be doubled, like the
other newer MPC85xx chips.
Since there are now more chips with a 2x divider than a 1x, and any new
85xx chips will probably be 2x, invert the sense of the #if so that it
lists the 1x chips instead of the 2x ones.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
If one custom board is using the 8MB flash, it is set
as FLASH_BASE = 0xef000000, TEXT_BASE = 0xef780000.
The current start.S code will be broken at switch_as.
It is because the TLB1[15] is set as 16MB page size,
EPN = TEXT_BASE & 0xff000000, RPN = 0xff000000.
For the 8MB flash case, the EPN = 0xefxxxxxx,
RPN = 0xffxxxxxx. Assume the virt address of switch_as
is 0xef7ff18c, the real address of the instruction at
switch_as should be 0xff7ff18c. the 0xff7ff18c is out
of the range of the default 8MB boot LAW window
0xff800000 - 0xffffffff.
So when we switch to AS1 address space at switch_as,
the core can't fetch the instruction at switch_as any
more. It will cause broken issue.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Assuming the OSes exception vectors start from the base of kernel address, and
the kernel physical starting address can be relocated to an non-zero address.
This patch enables the second core to have a valid IVPR for debugger before
kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid
value for second core which runs kernel at different physical address other
than 0x0.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Export the localbus frequency in the device tree, the same way the CPU, TB,
CCB, and various other frequencies are exported in their respective device
tree nodes.
Some localbus devices need this information to be programed correctly, so
it makes sense to export it along with the other frequencies.
Unfortunately, when someone wrote the localbus dts bindings, they didn't
bother to define what the "compatible" property should be. So it seems no
one was quite sure what to put in their dts files.
Based on current existing dts files in the kernel source, I've used
"fsl,pq3-localbus" and "fsl,elbc" for MPC85xx, which are used by almost all
of the 85xx devices, and are looked for by the Linux code. The eLBC is
apparently not entirely backward compatible with the pq3 LBC and so eLBC
equipped platforms like 8572 won't use pq3-localbus.
For MPC86xx, I've used "fsl,elbc" which is used by some of the 86xx systems
and is also looked for by the Linux code. On MPC8641, I've also used
"fsl,mpc8641-localbus" as it is also commonly used in dts files, some of
which don't use "fsl,elbc" or any other acceptable name to match on.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This warning is issued by modern ARM-EABI GCC on non-thumb targets.
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
This patch now adds a flush to the data cache upon relocation. The
current implementation is missing this. Only a comment states that it
should be done. So let's really do it now.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch adds the CONFIG_SKIP_LOWLEVEL_INIT option to start.S. This
enables support for boards where the lowlevel initialization is
already done when U-Boot runs (e.g. via OnChip ROM).
This will be used in the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Since commit 561858ee building for FADS823 and RRvision
doesn't work. Let's include version.h and timestamp.h
unconditionally to fix the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently the arm926ejs tree has the armv4 option set during compilation.
This flag does not belong here because a arm926 CPU is always a armv5 CPU.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Moved up the initialization of GD so C code like set_tlb() can use
gd->flags to determine if we've relocated or not in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
If the virtual address for CCSRBAR is the same after relocation but
the physical address is changing we'd end up having two TLB entries with
the same VA. Instead we new us the new CCSRBAR virt address + 4k as a
temp virt address to access the old CCSRBAR to relocate it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Add define used to determine if PCI1 interface is in PCI or PCIX mode.
Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Removed while(1) hang if memctl_intlv_ctl is set wrong.
Remove embedded tabs from strings.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
All mpc8548-based boards should implement the suggested workaround
to CPU 2 errata. Without the workaround, its possible for the
8548's core to hang while executing a msync or mbar 0 instruction
and a snoopable transaction from an I/O master tagged to make
quick forward progress is present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch fix the broken boot from NOR Flash on AT91RM9200 boards, if
CONFIG_AT91RM9200 is defined and nor preloader is used.
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Expanded OCM TLB to allow access to 64K OCM as well as 256K of
internal SRAM.
Adjusted internal SRAM initialization to match updated user
manual recommendation.
OCM & ISRAM are now mapped as follows:
physical virtual size
ISRAM 0x4_0000_0000 0xE300_0000 256k
OCM 0x4_0004_0000 0xE304_0000 64k
A single TLB was used for this mapping.
Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added include/asm-ppc/ppc4xx-isram.h and moved internal SRAM and
L2 cache DCRs from ppc440.h to this new header.
Also converted these DCR defines from lowercase to uppercase and
modified referencing modules to use them.
Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
At least some (old ?) versions of the AT91Bootstrap do not set up the
PLLB correctly to 48 MHz in order to make USB host function correctly.
This patch sets up the PLLB to the same values Linux uses, and makes USB
work ok on the following CPUs:
- AT91CAP9
- AT91SAM9260
- AT91SAM9263
This patch also defines CONFIG_USB_STORAGE and CONFIG_CMD_FAT for all
the relevant AT91CAP9/AT91SAM9 atmel boards.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This is needed on Canyonlands which still has an exception pending
while running relocate_code(). This leads to a failure after trap_init()
is moved to the top of board_init_r().
Signed-off-by: Stefan Roese <sr@denx.de>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
We define CONFIG_MONITOR_BASE_EARLY to define the initial location
of the bootpage in flash. Use this to create an early mapping
definition for the FLASH, and change the early_bats code to use this.
This change facilitates the relocation of the flash since the early
mappings are no longer tied to the final location of the flash.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Using a mtmsr/blr means that you have to be executing at the
same virtual address once you enable translation. This is
unnecessarily restrictive, and is not really how this is
usually done. Change it to use the more common mtspr SRR0/SRR1
and rfi method.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
In order to later allow for a physical relocation of the
flash, setup_bats, which sets up the final BAT mapping
for the board, needs to happen *after* init_laws().
Otherwise, there will be no window programmed for the flash
at the new physical location at the point when we change
the mmu translation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Affected boards:
Several MPC8xx boards
Several MPC8260/MPC8272 boards
Several MPC85xx boards
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch will move au1x00_eth_initialize from net/eth.c to cpu_eth_init
as a part of ongoing eth_initialize cleanup work. The function ret value
is also fixed as it should be negative on fail.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
OMAP identification is implemented in 'cpuinfo.c' and located in ARM926EJ-S directory.
It makes sense to place this file in OMAP specific subdirectory, i.e. cpu/arm926ejs/omap
Signed-off-by: Roman Mashak <romez777@gmail.com>
We put the bootpg for the secondary cpus into memory and use
BPTR to get to it. This is a step towards converting to the
ePAPR boot methodology. Also, the code is written to
deal properly with more than 4GB of RAM.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Currently, the CCSR gets relocated while translation is
enabled, meaning we need 2 BAT translations to get to both the
old location and the new location. Also, the DEFAULT
CCSR location has a dependency on the BAT that maps the
FLASH region. Moving the relocation removes this unnecessary
dependency. This makes it easier and more intutive to
modify the board's memory map.
Swap BATs 3 and 4 on 8610 so that all 86xx boards use the same
BAT for CCSR space.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The error was caused by the change for strmhz() in cpu.c.
A few of them were one extra close parenthesis.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Consolidate ATA, ePORT, QSPI, FlexCan, PWM, RNG,
MDHA, SKHA, INTC, and FlexBus structures and
definitions in immap_5xxx.h to more unify modules
header files. Append DSPI support for m547x_8x.
SSI cleanup. Remove USB Host structure from immap_539.h.
Apply changes to use FlexBus structures in mcf52x2's
cpu_init.c and platform configuration files.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
The patch is following the commit 3924384060
mpc86xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
also, the r2 is used as global data pointer.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The current calculation will fail to cover all memory if
its size is not a power of two.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The commit 67256678f0 add
the another global data pointer save, but in fact the
global data pointer will be initialized in the board_init_r,
so remove it such as the 85xx/83xx family.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
I believe these code was copied from 74xx family, but for
86xx, it is unused.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
We must invalidate TLBs before MMU turn on, but
currently the code is not, if there are some stale
TLB entry valid in the TLBs, it will cause strange
issue.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Renamed show_boot_progress in assembler init phase to
show_boot_progress_asm to avoid link conflicts with C version
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
The 8572 DDR erratum1:
DDR controller may enter an illegal state when operating
in 32-bit bus mode with 4-beat bursts.
Description:
When operating with a 32-bit bus, it is recommended that
DDR_SDRAM_CFG[8_BE] is cleared when DDR2 memories are used.
This forces the DDR controller to use 4-beat bursts when
communicating to the DRAMs. However, an issue exists that
could lead to data corruption when the DDR controller is
in 32-bit bus mode while using 4-beat bursts.
Projected Impact:
If the DDR controller is operating in 32-bit bus mode with
4-beat bursts, then the controller may enter into a bad state.
All subsequent reads from memory is corrupted.
Four-beat bursts with a 32-bit bus only is used with DDR2 memories.
Therefore, this erratum does not affect DDR3 mode.
Work Arounds:
To work around this issue, software must set DEBUG_1[31] in
DDR memory mapped space (CCSRBAR offset + 0x2f00 for DDR_1
and CCSRBAR offset + 0x6f00 for DDR_2).
Currenlty, the code is using incorrect register DDR_SDRAM_CFG_2
as condition, but it should be DDR_SDRAM_CFG register.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Introduce CONFIG_E500MC to deal with the minor differences between
e500v2 and e500mc.
* Certain fields of HID0/1 don't exist anymore on e500mc
* Cache line size is 64-bytes on e500mc
* reset value of PIR is different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using CONFIG_SYS_CACHELINE_SIZE instead of 31 means we can handle
e500mc's 64-byte cacheline properly when it gets added.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.
Any custom xilinx ppc405 board can be added very easily with no code
duplicity.
This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h
This patch is prepared to work with the latest version of EDK (10.1)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Some Blackfin UARTs are read-to-clear while others are write-to-clear.
This can cause problems when we poll the LSR and then later try and handle
any errors detected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the sti instruction to set the initial interrupt mask rather than
banging on the core IMASK MMR to save both space and time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We should use the algorithm in the Linux kernel so that the UART divisor
calculation is more accurate. It also fixes problems on some picky UARTs
that have sampling anomalies.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
During cpu init, make sure we initialize the CEC properly so that
interrupts can fire and be handled while U-Boot is running.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is done to allow other 83XX based platforms which also have UPM
(e.g. 8360) to configure and use their UPM in u-boot.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The rfcks should be shifted by 28 bits left. We didn't notice the bug
because we were using only 100MHz clocks (for which rfcks == 0).
Though, for SGMII we'll need 125MHz clocks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Previously only the NOR flash mapping was written into the ranges
property of the ebc node. This patch now writes all enabled chip
select areas into the ranges property.
Signed-off-by: Stefan Roese <sr@denx.de>
Provide a weak defined routine to retrieve the CPU number for
reference boards that have multiple CPU's. Default behavior
is the existing single CPU print output. Reference boards with
multiple CPU's need to provide a board specific routine.
See board/amcc/arches/arches.c for an example.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add the capability to configure a PPC440 based IBM SDRAM
Controller with static, compiled-in, values. PPC440 memory subsystem
includes a Memory Queue core.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Some cores don't support ethernet stashing at all, and some
instances have errata. Adds 3 properties to gianfar nodes
which support stashing. For now, just add this support to
85xx SoCs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Fix some bugs:
1. Correctly set intlv_ctl in cs_config.
2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
3. Set base_address and total memory for each ddr controller in memory
controller interleaving mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache. This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
At least some revisions of the 8313, and possibly other chips, do not
wait for all pages of the initial 4K NAND region to be loaded before
beginning execution; thus, we wait for it before branching out of the
first NAND page.
This fixes warm reset problems when booting from NAND on 8313erdb.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC
values. This fixes the occasional 440SPe hard locking issues when the 440SPe's
dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver).
Previously the appropriate initialization had been made in Linux, by the
ppc440spe ADMA driver, which is wrong because modifying the MQ configuration
registers after normal operation has begun is not supported and could
have unpredictable results.
Comment from Stefan: This patch doesn't change the resulting value of the
MQ registers. It explicitly sets/clears all bits to the desired state which
better documents the resulting register value instead of relying on pre-set
default values.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit dffd2446fb.
The fix introduced by this patch is not correct. The problem is
that the documentation is not correct for the MPC8544 with regards
to which bit in PORDEVSR2 is for the SEC_CFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reference manual states that MxMR[MAD] increment is the indication
of write to UPM array is complete. Honour that. Also, make the dummy
write explicit.
also fix the comment.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
At a lot of places in the code the PIPE_INTERRUPT flags and friends
are used wrong. The wrong bits are compared to this flag resulting
in wrong conditions. Also there are macros that should be used for
PIPE_* flags.
This patch tries to fix them all, however, I was not able to test the
changes, because I do not have any of these boards.
Review required!
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
Not know how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Measurements with our MPC8544 board showed that the I2C bus frequency
is wrong by a factor of 1.5. Obviously, the interpretation of the
MPC85xx_PORDEVSR2_SEC_CFG bit of the cfg_sec_freq register is not
correct. There seems to be an error in the 8544 RM.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Switch to the standard CFG_HZ=1000 value, while at it, minor white-space
cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads,
provides 2% or 0.4% precision depending on the
CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s
boot-delay.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
After changing SDRAM_CLKTR phase value rerun the memory preload
initialization sequence (INITPLR) to reset and relock the memory
DLL. Changing the SDRAM_CLKTR memory clock phase coarse timing
adjustment effects the phase relationship of the internal, to the
PPC chip, and external, to the PPC chip, versions of MEMCLK_OUT.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
ePAPR says if the *cache-block-size is the same as *cache-line-size
than we don't need the *cache-line-size property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
eventually leads to a machine check. This change assures that DPRAM
is allocated only once in that case.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].
The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: Stefan Roese <sr@denx.de>
This patch prevents linker error on AT91RM9200 boards, if
CONFIG_CMD_I2_TREE is set.
It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function.
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
This patch changes get_timer() for i.MX to return the time since
'base' instead of the time since the counter was at zero.
Symptom seen is flash timeout errors when erasing or programming a
sector using the common cfi flash code.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
1) Change the i.MX serial driver to use the baud rate set in the
u-boot environment
2) don't assume a 16MHz value for PERCLK1 in baud rate calculations
3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write
one to clear" like other status bits in the reg.)
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction. Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes warnings like this:
start.S:0: warning: target CPU does not support interworking
which come from some ARM cross compilers and are caused by hard-coded
(with "--with-cpu=arm9" configuration option) ARM targets (which
support ARM Thumb instructions), while the ARM target selected from
the command line (with "-march=armv4") doesn't support Thumb
instructions.
This warning is issued by the compiler regardless of the real use of
the Thumb instructions in code.
To fix this problem, we use options according to compiler version
being used.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a compilation warning for the PIP405 board. It moves the
#ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't
occur anymore. I am a little unsure if this #ifdef is at the correct
place now or if it could be removed completely. This needs to get
tested on the PIP405 board.
Signed-off-by: Stefan Roese <sr@denx.de>
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Alternate SDRAM DDR autocalibration routine that can be generically used
for any PPC4xx chips that have the IBM SDRAM Controller core allowing for
support of more DIMM/memory chip vendors and gets the DDR autocalibration
values which give the best read latency performance (SDRAM0_RDCC.[RDSS]).
Two alternate SDRAM DDR autocalibration algoritm are provided in this patch,
"Method_A" and "Method_B". DDR autocalibration Method_A scans the full range
of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a
lot longer to run than Method_B. Method_B executes in the same amount of time
as the currently existing DDR autocalibration routine, i.e. 1 second or so.
Normally Method_B is used and it is set as the default method.
The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM
Controller registers.[bit-field]:
1) SDRAM0_RQDC.[RQFD]
2) SDRAM0_RFDC.[RFFD]
This alternate PPC4xx DDR autocalibration code calibrates the following
IBM SDRAM Controller registers.[bit-field]:
1) SDRAM0_WRDTR.[WDTR]
2) SDRAM0_CLKTR.[CKTR]
3) SDRAM0_RQDC.[RQFD]
4) SDRAM0_RFDC.[RFFD]
and will also use the calibrated settings of the above four registers that
produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS]
register.[bit-field].
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The "GPIO" port mux is used on AVR32 UC3 parts as well as AT32AP7200 and
all later AVR32 chips. This patch adds a driver for it, implementing the
same API as the existing portmux-pio driver but with more functionality.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace the avr32-specific gclk_init() board hook with the standard
board_postclk_init() hook which is supposed to run at the same point
during initialization.
Provide a dummy weak alias for boards not implementing this hook. The
cost of this is:
- 2 bytes for the dummy function (retal 0)
- 2 bytes for each unnecessary function call (short rcall)
which is a pretty small price to pay for avoiding lots of #ifdef
clutter. In this particular case, all boards probably end up slightly
smaller because we avoid the conditional checking if the gclk_init
symbol is NULL.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add two helper functions for configuring and enabling generic clocks:
- gclk_enable_output: Enables output on a GCLKx pin
- gclk_set_rate: Configures a gclk to run at a specific rate
This should eliminate any reason to go mucking about with PM registers
from board code.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
- Separate the portmux configuration functionality from the GPIO pin
control API.
- Separate the controller-specific code from the chip-specific code.
- Allow "ganged" port configuration (multiple pins at once).
- Add more flexibility to the "canned" peripheral select functions:
- Allow using more than 23 address bits, more chip selects, as
well as NAND- and CF-specific pins.
- Make the MACB SPEED pin optional, and choose between MII/RMII
using a parameter instead of an #ifdef.
- Make it possible to use other MMC slots than slot 0, and support
different MMC/SDCard data bus widths.
- Use more reasonable pull-up defaults; floating pins may consume a
lot of power.
- Get rid of some custom portmux code from the mimc200 board code. The
old gpio/portmux API couldn't really handle its requirements, but
the new one can.
- Add documentation.
The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.
This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>
Changes since v1:
* Enable pullup on NWAIT
* Add missing include to portmux-pio.h
* Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This function is needed for the new NAND infrastructure. We only need
a dummy implementation though for the NDFC.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a UIC external_interrupt hang if critical or non-critical
interrupt is set at the same time as a normal interrupt is set on UIC0.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Removed Magic numbers from Initialization preload registers
Tested with Kilauea, Glacier, Canyonlands and Katmai boards
About 5-7% improvement seen for LMBench memtests
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
not show how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Compute DIMM parameters based upon the SPD information.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Compute DIMM parameters based upon the SPD information in spd.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a helper function to unlock the PCI configuration bit, so that
any extra PCI setup (such as outbound windows, etc.) can be done after
using the 83XX_GENERIC_PCI code to set up the PCI bus.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- According to ARM Dual-Timer Module (SP804) TRM (ARM DDI0271),
-- Timer Value Register @ TIMER Base + 4 is Read-only.
-- Prescale Value (Bits 3-2 of TIMER Control register)
can only be one of 00,01,10. 11 is undefined.
-- CFG_HZ for Versatile board is set to
#define CFG_HZ (1000000 / 256)
So Prescale bits is set to indicate
- 8 Stages of Prescale, Clock divided by 256
- The Timer Control Register has one Undefined/Shouldn't Use Bit
So we should do read/modify/write Operation
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
During recent PCI-E tests it has been found that current
driverl level and de-emphasis values are not set correctly.
After sweeping throgh all de-ephasis values, it was found that
0x130 is a right value. Where 0x13 is driver level and 0 is
de-emphasis.
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes some minor issues introduced with the patch:
ppc4xx: Optimize PLB4 Arbiter... from Prodyut Hazarika:
- Rework memory-queue and PLB arbiter optimization code, that the
local variable is not needed anymore. This removes one #ifdef.
- Use consistant spacing in ppc4xx.h header (XXX + 0x01 instead
of XXX+ 0x01). This was not introduced by Prodyut, just a
copy-paste problem.
Signed-off-by: Stefan Roese <sr@denx.de>
PPC405EX and PPC460EX/GT/SX
- Read pipeline depth set to 4 for PPC440SP/SPE, PPC405EX, PPC460EX/GT/SX
processors
- Moved PLB4 Arbiter register definitions to ppc4xx.h since it is shared
across processors (405 and 440/460)
- Optimize Memory Queue settings for PPC440SP/SPE and PPC460EX/GT/SX
processors
- Add register bit definitions for Memory Queue Configuration registers
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move to using the environment variables 'ethaddr', 'eth1addr', etc..
instead of bd->bi_enetaddr, bi_enet1addr, etc.
This makes the code a bit more flexible to the number of ethernet
interfaces.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Here comes a trivial patch to cpu/arm926ejs/davinci/nand.c. Unfortunately I
don't have hardware handy so I can not test it at the moment but changes are
rather trivial so it should work. It would be nice if somebody with a
hardware checked it anyways.
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
This patch changes the 4xx NAND driver ndfc.c to match the new
infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.
Tested successfully on AMCC Sequoia and Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
This is needed because we will be possibly be locating
devices at physical addresses above 32bits, and the asm
preprocessing does not appear to deal with ULL constants
properly. We now call write_bat in lib_ppc/bat_rw.c.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
On ADS5121 when booting linux the following errors are seen:
Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND
This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming. This patch
fixes this by being smarter about what to
fixup.
Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".
Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.
Signed-off-by: John Rigby <jrigby@freescale.com>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
Use CFG_MIPS_TIMER_FREQ when computing the baudrate divisor
on alchemy cpus.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch fixes a problem with incorrect MODTx (On Die Termination)
setup for a configuration with multiple DIMM's and multiple ranks.
Without this change Katmai was unable to boot Linux with DDR2 frequency
>= 533MHz and mem>=3GB. With this patch Katmai successfully boots Linux
with DDR2 frequency = 640MHz and mem=4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
-This patchs gives support for the embbedded ppc440
on the Virtex5 FPGAs
-interrupts.c divided in uic.c and interrupts.c
-xilinx_irq.c for xilinx interrupt controller
-Include modifications propossed by Stefan Roese
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
The L2 size detection code was a bit confusing and we kept having to add
code to it to handle new processors. Change the sense of detection so we
look for the older processors that aren't changing.
Also added support for 1M cache size on 8572.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some boards that have external 16550 UARTs don't have a direct
tie between bi_busfreq and the clock used for the UARTs. Boards
that do have such a tie should set CFG_NS16550_CLK to be
get_bus_freq(0) -- which most of them do already.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
With a page size of BOOKE_PAGESZ_16M, both the real and effective
addresses must be multiples of 16MB. The hardware silently truncates
them so the code happens to work. This patch clarifies the situation
by establishing addresses that the hardware doesn't need to truncate.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete the crypto node if not on an E-processor. If on 8360 or 834x family,
check rev and up-rev crypto node (to SEC rev. 2.4 property values)
if on an 'EA' processor, e.g. MPC8349EA.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
Remove all CFG_CSn_RO in cpu/mcf52x2/cpu_init.c. If
CFG_CSn_RO is defined as 0, the chipselect will not
be assigned.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Rename CONFIG_MCFTMR to CONFIG_MCFRTC to include real time
clock module in cpu/<cf arch>/cpu_init.c
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch now moves common.h to the top of the inlcude list. This
is needed for boards with CONFIG_PHYS_64BIT set (e.g. katmai), so that
the phys_size_t/phys_addr_t are defined to the correct size in this
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch reworks the 440GX interrupt handling so that the common 4xx
code can be used. The 440GX is an exception to all other 4xx variants
by having the cascading interrupt vectors not on UIC0 but on a special
UIC named UICB0 (UIC Base 0). With this patch now, U-Boot references
the 440GX UICB0 when UIC0 is selected. And the common 4xx interrupt
handling is simpler without any 440GX special cases.
Also some additional cleanup to cpu/ppc4xx/interrupt.c is done.
Signed-off-by: Stefan Roese <sr@denx.de>
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for placing the RGMII bridge on the
PPC405EX(r) into MII/GMII mode and allows a board-specific
configuration to specify the bridge mode at compile-time.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch completes the preprocessor mneomics for the IBM DDR2 SDRAM
controller registers (MODT and INITPLR) used by the
PowerPC405EX(r). The MMODE and MEMODE registers are unified with their
peer values used for the INITPLR MR and EMR registers,
respectively. Finally, a spelling typo is correct (MANUEL to MANUAL).
With these mnemonics in place, the CFG_SDRAM0_* magic numbers for
Kilauea are replaced by equivalent mnemonics to make it easier to
compare and contrast other 405EX(r)-based boards (e.g. during board
bring-up).
Finally, unified the SDRAM controller register dump routine such that
it can be used across all processor variants that utilize the IBM DDR2
SDRAM controller core. It produces output of the form:
PPC4xx IBM DDR2 Register Dump:
...
SDRAM_MB0CF[40] = 0x00006701
...
which is '<mnemonic>[<DCR #>] = <value>'. The DCR number is included
since it is not uncommon that the DCR values in header files get mixed
up and it helps to validate, at a glance, they match what is printed
in the user manual.
Tested on:
AMCC Kilauea/Haleakala:
- NFS Linux Boot: PASSED
- NAND Linux Boot: PASSED
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ADS5121 Rev 3 board is now the default config
config targets are now
ads5121_config
Rev 3 board with
PCI
M41T62 on board RTC
512MB DRAM
ads5121_rev2_config
Rev 2 board with
No PCI
256MB DRAM
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Rigby <jrigby@freescale.com>
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM.
To support such configurations, we "only" map the first 2GB via the TLB's. We
need some free virtual address space for the remaining peripherals like, SoC
devices, FLASH etc.
Note that ECC is currently not supported on configurations with more than 2GB
SDRAM. This is because we only map the first 2GB on such systems, and therefore
the ECC parity byte of the remaining area can't be written.
Signed-off-by: Stefan Roese <sr@denx.de>
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This makes it easier to use the driver on other platforms.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
After we move the atmel_mci driver into drivers/mmc, we can't select
it with CONFIG_MMC anymore. Introduce a new symbol specifically for
this driver so that there's no ambiguity.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The compiler will help find mismatches between printf formats and
arguments if you let it. This patch adds the necessary attributes to
declarations in include/common.h, then begins to correct the resulting
compiler warnings. Some of these were bugs, e.g., "$d" instead of
"%d" and incorrect arguments. Others were just annoying, like
int-long mismatches on a system where both are 32 bits. It's worth
fixing the annoying errors to catch the real ones.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The watchdog on 8610 board is enabled by setting sw[6]
to on. Once enabled, the watchdog can not be disabled
by software. So feed the dog in u-boot is necessary for
normal operation.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Remove duplicate code in cpu/arm926ejs/davinci/lxt972.c.
Remove duplicate code in a if/else block in
cpu/arm926ejs/davinci/lxt972.c.
Fixed style issues.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove duplicate definitions in include/lxt971a.h.
Remove duplicate registers and bits definitions in
include/lxt971a.h for standard MII registers, and
use values in include/miiphy.h instead.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This change helps with better handling with others
Xilinx based platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefan Roese <sr@denx.de>
This patch is the first step in cleaning up net/eth.c, by moving Ethernet
initialization to CPU or board-specific code. Initial implementation is
only on the Freescale TSEC controller, but others will be added soon.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Conflicts:
board/amirix/ap1000/serial.c
board/exbitgen/exbitgen.c
board/exbitgen/flash.c
board/ml2/serial.c
board/xilinx/ml300/serial.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Register URXD contains status information in bits [15..8].
With status bit 15 set, CTRL-C was reported as 0x8003 instead
of 0x03. Therefore CTRL-C was not detected.
To solve this, bits [15..8] were masked out now.
Signed-off-by: Juergen Kilb <J.Kilb@gmx.de>
Acked-by: Felix Radensky <felix@embedded-sol.com>
This patch fixes a bug where the 460EX/GT PCIe UTLSET1 register was
configured incorrectly. Thanks to Olga Buchonina from AMCC for pointing
this out.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch implements a fix provided by AMCC so that the lockup upon
simultanious traffic on AHB USB OTG, USB 2.0 and SATA doesn't occur
anymore:
Set SDR0_AHB_CFG[A2P_INCR4] (bit 24) and clear SDR0_AHB_CFG[A2P_PROT2]
(bit 25) for a new 460EX errata regarding concurrent use of AHB USB OTG,
USB 2.0 host and SATA.
This errata is not officially available yet. I'll update the comment
to add the errata number later.
Signed-off-by: Stefan Roese <sr@denx.de>
This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.
There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.
Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
During 83xx setup the "System I/O configuration register high" gets
overwritten with user defined value if CFG_SICRH is defined.
Regarding to the MPC834x manual (Table 5-28 reve.1) bits 28+29 of SICRH
must keep their reset value regardless of configuration.
On my board (using RGMII) those bits are set after reset - yet it's
unclear where they come from.
The patch keeps both bits on MPC834x and MPC8313.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
to avoid this:
cpu.c:47:1: warning: "CPU_TYPE_ENTRY" redefined
In file included from cpu.c:33:
/home/kim/git/u-boot/include/asm/processor.h:982:1: warning: this is the location of the previous definition
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
As pointed out by Guennadi Liakhovetski (thanks), pin2 is already shifted
left by one. So the additional shift is bogus.
Signed-off-by: Stefan Roese <sr@denx.de>
Use the new GPIO manipulation functions to set up the chip select lines,
and make sure both busses use GPIO for chip select control.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Building for 4xx doesn't work since commit 4dbdb768:
In file included from 4xx_pcie.c:28:
include/asm/processor.h:971: error: expected ')' before 'ver'
make[1]: *** [4xx_pcie.o] Error 1
This patch fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose. This makes life
a bit easier going forward with the new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.
In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.
Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The boot output is now aligned poperly with other boot output
lines, e.g.:
FLASH: 128 MB
L2: 512 KB enabled
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The current cpu identification code is used just to return the name
of the processor at boot. There are some other locations that the name
is useful (device tree setup). Expose the functionality to other bits
of code.
Also, drop the 'E' suffix and add it on by looking at the SVR version
when we print this out. This is mainly to allow the most flexible use
of the name. The device tree code tends to not care about the 'E' suffix.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_OF_LIBFDT instead to support flattened device trees. It is
cleaner, has better functionality, and is better supported.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible. Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
CONFIG_SOC_AU1X00
Common Alchemy Au1x00 stuff. All Alchemy processor based machines
need to have this config as a system type specifier.
CONFIG_SOC_AU1000, CONFIG_SOC_AU1100, CONFIG_SOC_AU1200,
CONFIG_SOC_AU1500, CONFIG_SOC_AU1550
Machine type specifiers. Each port should have one of aboves.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible. Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd to prevent us from trying to access
non-mapped memory.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
We use upper case letters for the AMCC processor defines (like
CONFIG_440SPE) in U-Boot. So the 440SPe is labeled CONFIG_440SPE and
not CONFIG_440SPe. This patch fixes the last misspelled config options.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch simplifies post_word_{load,store} by using the preprocessor
to eliminate redundant, copy-and-pasted code.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.
Changed in v4:
- Update to new API
- Handle zero-length transfers appropriately. The user may send a
zero-length SPI transfer with SPI_XFER_END set in order to
deactivate the chip select after a series of transfers with chip
select active. This is useful e.g. when polling the status
register of DataFlash.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.
Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
* spi_cs_activate(): Activates the chipselect for a given slave
* spi_cs_deactivate(): Deactivates the chipselect for a given slave
* spi_cs_is_valid(): Determines if the given bus/chipselect
combination can be activated.
Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)
To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.
Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.
spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.
This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.
I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.
But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?
Changed in v4:
- Build fixes for various boards, drivers and commands
- Provide common struct spi_slave definition that can be extended by
drivers
- Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
- Make default bus and mode build-time configurable
- Override default SPI bus ID and mode on mx32ads and imx31_litekit.
Changed in v3:
- Add opaque struct spi_slave for controller-specific data associated
with a slave.
- Add spi_claim_bus() and spi_release_bus()
- Add spi_free_slave()
- spi_setup() is now called spi_setup_slave() and returns a
struct spi_slave
- soft_spi now supports four SPI modes (CPOL|CPHA)
- Add bus parameter to spi_setup_slave()
- Convert the new i.MX32 SPI driver
- Convert the new MC13783 RTC driver
Changed in v2:
- Convert the mpc8xxx_spi driver and the mpc8349emds board to the
new API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.
This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:
csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG
I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch makes the common 4xx ECC code really usable on 440GP style
platforms.
Since the IBM DDR controller used on 440GP/GX/EP/GR is not register
compatible to the IBM DDR/2 controller used on 405EX/440SP/SPe/460EX/GT
we need to make some processor dependant defines used later on by the
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
