In case SError happens at EL2, if SCR_EL3[EA] is not routing it to
EL3, and SCR_EL3[RW] is set to aarch64, setting HCR_EL2[AMO] routes
the exception to EL2. Otherwise this exception is not taken.
Signed-off-by: York Sun <york.sun@nxp.com>
Add board support for Ficus EE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* Gigabit Ethernet
* USB 2.0
* MMC
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[Reworked based on common Rock960 family support]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add board support for Rock960 CE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* USB 2.0
* MMC
This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which
is being used on the board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Those pins would be used by many boards.
Commit grabbed from Linux:
commit b41023282d07b61a53e2c9b9508912b1e7ce7b4f
Author: Randy Li <ayaka@soulik.info>
Date: Thu Jun 21 21:32:10 2018 +0800
arm64: dts: rockchip: add some common pin-settings to rk3399
Those pins would be used by many boards.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
Add SPCR table description as it provided in Linux kernel.
Port subtype for ACPI_DBG2_SERIAL_PORT is used as an interface type in SPCR.
Thus, provide a set of definitions to be utilized later.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This functions allow us to get and remap I/O addresses by name, which is useful when there are multiple reg addresses indexed by reg-names property.
This is needed in bmips dma/eth patch series, but can also be used on many
other drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present sandbox has a start.o in the 'start' target but also includes
it in the normal target list. This is not how this is normally handled. It
is needed because sandbox does not include the u-boot-init variable in its
link rule.
Update the rule and move start.o from the normal target list to the
'extras' list.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the RAM buffer is not inited unless it is read from a file,
likely produced by an earlier phase of U-Boot. This causes valgrind
warnings whenever the RAM buffer is used. Correct this by initing it if
needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
This patch adds kconfig option RISCV_SMODE to run U-Boot in
S-mode. When this opition is enabled we use s<xyz> CSRs instead
of m<xyz> CSRs.
It is important to note that there is no equivalent S-mode CSR
for misa and mhartid CSRs so we expect M-mode runtime firmware
(BBL or equivalent) to emulate misa and mhartid CSR read.
In-future, we will have more patches to avoid accessing misa and
mhartid CSRs from S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
Set environment variable 'platform' containing the CPU type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The i2c6 node is missing in mainline Linux thus far, pull it
into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SCIF2 node is not in Linux 4.17 DTs on E3, pull it into U-Boot
specific DT extras until it hits mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are not in Linux 4.17 DTs in E3, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the
node into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the
AVB node extras into U-Boot specific DT until they hit mainline Linux,
to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The RPC DT bindings are still work in progress. Extract the RPC DT node
from the DT to allow easier update and so it can be replaced once the DT
bindings are stable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Add label to the /soc node, so it can be referenced from the U-Boot DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
This patch switches MCR3000 board to the new DM watchdog.
The change in u-boot.lds is because MCR3000.o grows a bit
with this patch and doesn't fit anymore below env_offset on
some versions of GCC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Enable the HS400 support in DT on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add regulators and pinmuxes for SDHI0 and SDHI1 SD and microSD
slots on E3 Ebisu and mark them as capable of up to SDR104 mode
of operation. With the SDHI fixes in place, it is now possible
to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable SDR104 modes on M3W and H3 boards. With the SDHI fixes
in place, it is now possible to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pinmux entry for the eMMC DS line, as it is connected on these boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
1. Try to guess a ARC core template that was used
i.e. not just name a core family but something more
menaingful like "ARC HS38", "ARC EM11D" etc.
We do it checking availability of the key differentiation
features like:
- Caches (we actually only check for L1 I$ fpr simplicity)
- XY-memory
- DSP extensions etc.
2. Identify ARC subsystems
3. Print core clock frequency
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
When an operating system started via bootefi tries to reset or power off
this is done by calling the EFI runtime ResetSystem(). On most ARMv8 system
the actual reset relies on PSCI. Depending on whether the PSCI firmware
resides the hypervisor (EL2) or in the secure monitor (EL3) either an HVC
or an SMC command has to be issued.
The current implementation always uses SMC. This results in crashes on
systems where the PSCI firmware is implemented in the hypervisor, e.g.
qemu-arm64_defconfig.
The logic to decide which call is needed based on the device tree is
already implemented in the PSCI firmware driver. During the EFI runtime
the device driver model is not available. But we can minimize code
duplication by merging the EFI runtime reset and poweroff code with
the PSCI firmware driver.
As the same HVC/SMC problem is also evident for the ARMv8 do_poweroff
and reset_misc routines let's move them into the same code module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Per Microsoft PE Format documentation [1], PointerToSymbolTable and
NumberOfSymbols should be zero for an image in the COFF file header.
Currently the COFF file header is hardcoded on RISC-V and these two
members are not zero.
This updates the hardcoded structure to clear these two members, as
well as setting the flag IMAGE_FILE_LOCAL_SYMS_STRIPPED so that we
can generate compliant *.efi images.
[1] https://docs.microsoft.com/zh-cn/windows/desktop/Debug/pe-format
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Per Microsoft PE Format documentation [1], PointerToSymbolTable and
NumberOfSymbols should be zero for an image in the COFF file header.
Currently the COFF file header is hardcoded on ARM and these two
members are not zero.
This updates the hardcoded structure to clear these two members, as
well as setting the flag IMAGE_FILE_LOCAL_SYMS_STRIPPED so that we
can generate compliant *.efi images.
[1] https://docs.microsoft.com/zh-cn/windows/desktop/Debug/pe-format
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Per Microsoft PE Format documentation [1], PointerToSymbolTable and
NumberOfSymbols should be zero for an image in the COFF file header.
Currently U-Boot is generating u-boot-app.efi in which these two
members are not zero.
This updates the build rules to tell linker to remove the symbol
table completely so that we can generate compliant *.efi images.
[1] https://docs.microsoft.com/zh-cn/windows/desktop/Debug/pe-format
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Per Microsoft PE Format documentation [1], PointerToSymbolTable and
NumberOfSymbols should be zero for an image in the COFF file header.
Currently U-Boot is generating u-boot-payload.efi image in which
these two members are not zero.
This updates the build rules to tell linker to remove the symbol
table completely so that we can generate compliant *.efi images.
[1] https://docs.microsoft.com/zh-cn/windows/desktop/Debug/pe-format
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwBjx8ACgkQfxc6PpAI
rebWEAf+PMc/M3X6cCKm+8P9xTNFv0gv234HVke1eTDG3eyZB6WQnJn5CS0LwyPj
JUfwk4xK0Sqev/sQ6RuzmxmPAgla6UrEFB355tiZRBtFsMgf8bfevOqbxVqMbZl/
bOe4YsFJ3sAgQDuhi2C5xzm2speGtaB8Qy8s1Zlv2sx3zEnLgRqVgeEVHzulZsk3
gAlWKN3ys6EueYnOladjrrvrfOX8SQKYbThI+ACy7suZbtasGRITwP/4fQoXtmOl
39e9WsiW6DBRW1sxNxpixrOS5trgWjOOFiKlY3GNWP+N34+9vYASwuBWwRWqfgXo
cmelT6AcGiPUbHyr4k0CJHKCJlSbaQ==
=p83K
-----END PGP SIGNATURE-----
Merge tag 'pull-30nov18' of git://git.denx.de/u-boot-dm
Fix sound on sandbox
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
Sync with other rockchip SoCs, use board_debug_uart_init() to
init default UART iomux.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like it is done for other Rockchip SoCs, introduce a board_usb_init()
function so that USB OTG can be functional on rv1108 too.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
The RK3399 SPL has two cases that may end in a hard-stop: if either
the pinctrl can not be initialised or if the DRAM fails to initialise.
Both have previously not triggered an error message unless DEBUG was
defined (i.e. both used debug() to print the error).
This converts both error messages to be printed using pr_err() to
ensure that some output points to the cause of the hard-stop.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions
into pinctrl-driver") moved the iomux settings out of the grf header
to prevent conflicts with the iomux definitions of other rockchip socs.
This also breaks the early uart setup, as the iomux for uart2 are needed.
To fix that just put the tiny amount of needed iomux definitions next to
the early uart code.
Fixes: 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions into pinctrl-driver")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip socs can route the debug uart pins through the d+ and d- pins
of one specific usbphy per soc. Add a config option and implement the
setting on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up to mark grf as maybe unused:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As the driver has been changed to be more specific, the DT compatible
property also needs to be adapted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
- Some Kirkwood boards converted to DM_SPI by Chris
- New Armada-385 SoC revision printed by Chris
- Ethernet enable on mcbin by Baruch
- Support 2 DRAM banks on Armada-8k boards by Baruch
Marvell have release a B0 revision of the Armada-385 SoC. This fixes a
hardware errata enabling RGMII to work when the Ethernet voltage is
configured to 3.3V.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The use of strcpy() to remove characters at the start of a string is safe
in U-Boot, since we know the implementation. But in os.c we are using the
C library's strcpy() function, where this behaviour is not permitted.
Update the code to use memmove() instead.
Reported-by: Coverity (CID: 173279)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Now that the buffer-overflow bug is fixed, we can enable sound on sandbox.
Drop the code which exits early.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we request a particular frequency but we may not get the exact
same frequency in response. So use the actual frequency for generation of
the square wave. This ensures that the pitch remains accurate on all host
machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this value is hard-coded in the function that generates a
square wave. Since sample rates vary between different hardware, it makes
more sense to have this as a parameter.
Update the function and its users.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch prevents disabling the FPGA bridges when
SPL or U-Boot is executed from FPGA onchip RAM.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This chip is on the board but handling should be done via firmware not
via Linux driver. Changing status property to keep it in the tree to
describe it instead of removing this node completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DC4 board has qspi on it hence define and enable
qspi node for it.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7623 SoCs from MediaTek.
As this u-boot is loaded by MTK proprietary preloader, there is no
low level initializtion codes.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related
code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some erratum workarounds call into C code before the stack
is setup, this can lead to values pushed onto the stack
being lost, firewall exceptions, and other undefined behavior.
Setup a temporary stack to allow these functions to work
correctly.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Based on the MCU R5 efuse settings, R5F cores in MCU domain
either work in split mode or in lock step mode.
If efuse settings are in lockstep mode: ROM release R5 cores
and SPL continues to run on the R5 core is lockstep mode.
If efuse settings are in split mode: ROM releases both the R5
cores simultaneously and allow SPL to run on both the cores.
In this case it is bootloader's responsibility to detect core
1 and park it. Else both the core will be running bootloader
independently which might result in an unexpected behaviour.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.
When no other boot medium are available (or by forcing the USB mode), the
ROM sets the primary USB port as device mode and waits for a Host to
enumerate.
When enumerated, a custom protocol described at [1] permits writing to
memory and execute some specific FIP init code to run the loaded
Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage.
In this mode, we can load different binaries that can be used by U-boot
like a script image file.
This adds support for a custom USB boot stage only available when the
boot mode is USB and the script file at a pre-defined address is valid.
This support was heavily copied from the Sunxi Allwinner FEL U-Boot support.
The tool pyamlboot described at [2], permits using this boot mode on boards
exposing the first USB port, either as OTG or Host port.
[1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md
[2] https://github.com/superna9999/pyamlboot/blob/master/README.md
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() functions to
weak functions into the board-common mach-meson file.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR Interface limited to DDR4 16bit
- The whole physical register address space has been moved to 0xfxxxxxxx
- The pinctrl setup has changed
- The clock tree is different enough to use a different driver
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a SoC architecture and add a custom config header or custom
board handler for a platform.
This drops the board CONFIGs and the duplicate boards configs headers in
favor of a single meson64.h config header.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. Dedicated defconfig are kept to customize
the names and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim2 derive from amlogic s912 reference design (Q200).
This patch moves the khadas-vim2 board support to a generic Q200 board,
while keeping a dedicated defconfig to customize the names and device tree.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).
All the code in these board is a copy/paste from the p212, which is
tedious to maintain. This change use p212 u-boot board for all these
boards, while keeping a dedicated defconfig to customize the names
and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Even if multiple board are selected through Kconfig, u-boot will only
compile one. This makes sense since compiling these targets will export
global symbols, such as board_init()
The change rework amlogic Kconfig so only one board may be selected at
a time
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.
Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Most architectures use jump_to_image_no_args() to jump from SPL to U-Boot.
At present sandbox is special in that it jumps in its
spl_board_load_image() call. This is not strictly correct, and means that
sandbox misses out some parts of board_init_r(), just as calling
bloblist_finish(), for example.
Change spl_board_load_image() to just identify the filename to boot, and
implement jump_to_image_no_args() to actually jump to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current method of starting U-Boot from U-Boot adds arguments to pass
the memory file through, so that memory is preserved. This is fine for a
single call, but if we call from TPL -> SPL -> U-Boot the arguments build
up and we have several memory files in the argument list.
Adjust the implementation to filter out arguments that we want to replace
with new ones. Also print a useful error if the exec() call fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox calls malloc() from various places in the OS layer and
this results in calls to U-Boot's malloc() implementation. It is better to
use the on in the OS layer, since it does not mix allocations with the
main U-Boot code.
Fix this by replacing calls with malloc() to os_malloc(), etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
At present os_jump_to_image() jumps to a given image, and this is written
to a file. But it is useful to be able to jump to a file also.
To avoid duplicating code, split out the implementation of
os_jump_to_image() into a new function that jumps to a file.
Signed-off-by: Simon Glass <sjg@chromium.org>
The old 'sb' command was deprecated in 2015 and replaced with 'host'. It
is useful to be able to access some internal sandbox state, particularly
for testing.
Resurrect the old command and provide a way to print some basic state
information (currently just the arguments to sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we don't have a test that of-platdata can be accessed in SPL.
Add this in as a command-line option to SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
BSS section was all the time separated for SPL but this symbol wasn't
enabled. It is necessary to have it enabled for OF_SEPARATE
configuration where DTB is appended to u-boot with DTB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make sense to add controller ID to model name to have it visible through
the logs to know which controller is used by which configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AndeStar RISC-V(V5) provide mcache_ctl register which
can configure I/D cache as enabled or disabled.
This CSR will be encapsulated by CONFIG_RISCV_NDS.
If you want to configure cache on AndeStar V5
AE350 platform. YOu can enable [*] AndeStar V5 ISA support
by make menuconfig.
This approach also provide the expansion when the
vender specific features are going to join in.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Add ae350_32.dts for 32 bit. And also rename
ae350.dts to ae350_64.dts for 64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
The bootm implementation of RISC-V diverges from that of other
architectures. Update it to match the implementation of other
architectures. The ARM implementation is used as a reference.
This adds the following features and changes to RISC-V.
* Add support for the BOOTM_STATE_OS_FAKE_GO command
* Call the remove function on devices with the removal flag set before
booting Linux
* Force disconnect USB devices from the host before booting Linux
* Print and add bootstage information to the device tree before booting
Linux
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Store the hart ID and device tree passed by the prior boot stage (in a0
and a1) in registers s0 and s1. Replace one use of s1 in start.S to
avoid overwriting it.
The device tree is also stored in memory to make it available to U-Boot
with the configuration CONFIG_OF_PRIOR_STAGE.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The mstatus CSR includes WPRI (writes preserve values, reads ignore
values) fields and must therefore not be set to zero without preserving
these fields. It is not apparent why mstatus is set to zero here since
it is not required for U-Boot to run. Remove it.
This instruction and others encode zero as an immediate. RISC-V has the
zero register for this purpose. Replace the immediates with the zero
register.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The labels nmi_vector, trap_vector and handle_reset in start.S are not
used for RISC-V. Remove them.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is now deprecated and no board is using it. Drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The machine trap-vector base address (mtvec) must be aligned on a 4-byte
boundary. Add the necessary align directive to trap_entry.
This patch also removes the global directive for trap_entry, which is
not required.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S uses both tabs and spaces after instructions. Fix this by only
using tabs after instructions.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Implement the functions invalidate_icache_range() and
invalidate_icache_all().
RISC-V does not have instructions for explicit cache-control. The
functions in this patch are implemented with the memory ordering
instruction for synchronizing the instruction and data streams. This may
be implemented as a cache flush or invalidate on simple processors,
others may only invalidate the relevant cache lines.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Hang on unhandled exceptions to prevent execution in a faulty state.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Undefined exception codes currently lead to an out-of-bounds array
access. Prevent this by treating undefined exception codes as
"reserved".
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Only the first four exception codes are defined. Add the missing
exception codes from the definition in RISC-V Privileged Architecture
Version 1.10.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
RISC-V U-Boot reimplements the generic io functions from
asm-generic/io.h. Remove the redundant implementation and include the
generic io.h instead.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Replace the barrier functions in arch/riscv/include/asm/io.h with those
defined in barrier.h, which is imported from Linux. This version is
modified to remove the include statement of asm-generic/barrier.h, which
is not available in U-Boot or required.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The RISC-V arch incorrectly uses 32-bit instead of 64-bit variables in
several places. Fix this.
In addition, BITS_PER_LONG is set to 64 on RV64I systems.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the -fdata-sections compiler option for RISC-V. Buildman reports
the binary size decrease from this as 8365.3 bytes.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Use the new Kconfig entries to construct the ISA string for the -march
compiler flag. The -mabi compiler flag is selected based on the base
integer instruction set.
With this change, the C (compressed instructions) ISA extension is now
enabled for all boards with CONFIG_RISCV_ISA_C set. Buildman reports a
decrease in binary size of 71590 bytes.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Kconfig entries for the C (compressed instructions) and A (atomic
instructions) ISA extensions. Only the C ISA extension is selectable.
This matches the configuration in Linux.
The Kconfig entries are not used yet. A follow-up patch will select the
appropriate compiler flags based on the Kconfig configuration.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_PHYS_64BIT should be enabled on RV64I systems. Select it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
RISC-V defines the base integer instruction sets as RV32I and RV64I.
Rename CPU_RISCV_32 and CPU_RISCV_64 to ARCH_RV32I and ARCH_RV64I to
match this convention.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
When we initialize the memory we need to autodetect rank and size
but this can happen only if we send the proper reset to both
memory module including cke signal.
For this reason we need initialize the physical on both channel because
we need to presume that both are connected. This way let the CLKE to be
activated at the right time with the memory reset coming from the cpu
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
At present sandbox drivers are mostly not used before relocation. Some of
these are needed by Chromium OS verified boot, since it uses sandbox TPL,
so update them accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to read a file from the host filesystem. This can be useful for
reading test data, for example. Also fix up the writing function which was
not the right version, and drop the debugging lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
DEBUG should not be defined in production code.
Change printf() to debug() where this writes a debug message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Some Armada 8K boards like Macchiatobin and Clearfog GT-8K use RAM from
external DIMM. Hard coding the RAM size in the device-tree is not
convenient. Fortunately, the ATF that initializes the RAM knows the size
of RAM, and U-Boot can query the ATF using a SMC call.
The ATF maps the lower 3G of RAM starting at address 0. Higher RAM is
mapped at 4G. This leaves a 1G hole between 3G and 4G for IO
peripherals. Use a second bi_dram[] entry to describe the higher RAM
area. As a result, CONFIG_NR_DRAM_BANKS must be set to 2 to use more
than 3GB RAM.
This code in this commit is mostly taken from downstream Marvell U-Boot
code by Grzegorz Jaszczyk.
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The kernel added SZ_4G macro in commit f2b9ba871b (arm64/kernel: kaslr:
reduce module randomization range to 4 GB).
Include linux/const.h for the _AC macro.
Drop a local SZ_4G definition in tegra code.
Cc: Tom Warren <twarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 86f21c96f4 (mips: Use common _AC macro now.) removed the _AC
definition from const.h. All other macros defined in const.h are not
used anywhere, and there is now no user of this header. Remove this
header.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use the global MIPS specific u-boot.lds for linking standalone programs
instead of the outdated ones in examples/standalone/. Also pass --gc-sections
in LDFLAGS_STANDALONE to optimize the size of standalone programs.
Finally remove the deprecated config.mk files in arch/mips/cpu/mips[32,64]/.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Introduce a new Makefile variable for passing LDFLAGS to standalone
programs. Currently the variable CONFIG_STANDALONE_LOAD_ADDR is
misued on some archs to pass a specific linker script.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI support
- Enable GPIO support
- Change max image size from 0x40000 to 0x80000
A note about the baudrate change:
The original Mediatek U-Boot version used 57600 baud. Lets move to a
more common and faster speed of 115200 baud. And remove the "console="
property from the DT as its not needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI NOR and NAND support
- Change MTD_UBI_BEB_LIMIT to 22
- Enable MTD Support
- Enable GPIO support
- Enable watchdog support
- Enable bootcounter support
- Enable version variable
- Change max image size from 0x80000 to 0xa0000
- Change SYS_MALLOC_LEN to 16MiB (because of UBI/UBIFS)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed to set the LEDs automatically to a default state, as
configured in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the available LEDs to the DTS file so that they can be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch enables and starts the watchdog on the MT7620 platform.
Currently the WD timeout is configured to 60 seconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed build error due to missing function prototype arch_misc_init]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Imply DM_ETH and DM_GPIO for ARCH_MT7620, as this platform now supports
ethernet and GPIO as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes an issue which has been noticed on the Gardena board, with
the watchdog enabled, where the watdchdog reset (after a system hang)
did result in reporting of 2.9 GiB and a hang after this. With this
patch applied the memory controller is correctly reset and initialized
again even after a watchdog reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support
for triggering DDR initialization from board_init_f().
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Considering the boot time requirements, Cortex-A core
should be able to start immediately after SPL on R5.
Add support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update Makefiles to generate:
- tiboot3.bin: Image format that can be processed by ROM.
Below is the tiboot3.bin image format that is required by ROM:
_______________________
| X509 |
| Certificate |
| ____________________ |
| | | |
| | u-boot-spl.bin | |
| | | |
| |___________________| |
|_______________________|
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
K3 based AM654 devices has DDR memory subsystem that comprises
Synopys DDR controller, Synopsis DDR phy and wrapper logic to
intergrate these blocks into the device. This DDR subsystem
provides an interface to external SDRAM devices. Adding support
for the initialization of the external SDRAM devices by
configuring the DDRSS registers and using the buitin PHY
routines.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
The current arch implementation of memcpy cannot be called
from thumb code, because it does not use bx instructions on return.
This patch addresses that. Note, that this patch does not touch
the hot loop of memcpy, so performance is not affected.
Tested on MXS (arm926ejs) with and without thumb-mode enabled.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Add pinmux test which test the following commands:
- pinmux list
- pinmux dev
- pinmux status
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Mark some tests as sandbox-centric]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Allow platform vendors to handle SError interrupt exceptions from
ARMv8 PSCI exception vectors by overriding this weak function
'plat_error_handler'.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Allow EL3 to handle all the External Abort and SError interrupt
exception occur in all exception levels.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
To support CONFIG_DISPLAY_CPUINFO, add "u-boot,dm-pre-reloc" for
all cpu nodes in Sandbox test.dts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It turns out commit c0434407b5 broke some boards which have DM CPU
driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail
to boot when print_cpuinfo() is called during boot.
Fixes: c0434407b5 ("board_f: Use static print_cpuinfo if CONFIG_CPU is active")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Now that we have a sandbox virtio transport driver, add some test
cases to test virtio uclass driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a Kconfig file in the board directory, so that some
board-specific options can be specified there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the generic io{read,write}{8,16,32} routines only support
MMIO access. With architecture like x86 that has a separate IO space,
these routines cannot be used to access I/O ports.
Implement x86-specific version to support both PIO and MMIO access,
so that drivers for multiple architectures can use these accessors
without the need to know whether it's MMIO or PIO.
These are ported from Linux kernel lib/iomap.c, with slight changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a call to dm_remove_devices_flags() to do_bootm_linux()
so that drivers that have one of the removal flags set (e.g.
DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may do some
last-stage cleanup before the OS is started.
arm and x86 already did such, and we should do the same for riscv.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
MIPS is the only architecture currently supported by U-Boot that does
not implement any of the in/out register access functions.
To have a interface that is useable across architectures, add the
functions to the MIPS architecture (implemented using the __raw_write
and __raw_read functions).
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use a starting address of 256MB which should be available. This helps to
make sandbox RAM buffers pointers more recognisable.
Signed-off-by: Simon Glass <sjg@chromium.org>
The upcoming changes to the regmap interface will contain a proper check
for plausibility when reading/writing from/to a register map. To still
have the current tests pass, increase the size of the memory region for
the syscon0 device, since one of the tests reads and writes beyond this
range.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Now that we fixed the pre-relocation driver binding for driver marked
with DM_FLAG_PRE_RELOC flag, add a test case to cover that scenario.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DE2 SoCs can support LCDs up to 1080p (e.g. A64), and 3MHz step won't
let PLL_VIDEO be high enough for them.
Use 6MHz step for PLL_VIDEO when using DE2, to satisfy 1080p LCD.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Pine64 LTS is an updated version of the Pine64, copying the
technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and
soldered SPI flash chip, even the broken SD card detect pin has been copied.
Consequently this leads to the .dts (copied from the kernel) just including
the SoPine baseboard .dts, and the defconfig being almost identical.
Nevertheless the boards deserves a separate config.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the
compatible name for the syscon controller, dropping the generic "syscon"
fallback. Using this new DT node will make the Ethernet driver in every
older kernel (or non-Linux kernels) fail to initialise the MAC device.
To allow booting distribution kernels (from installer images via UEFI,
for instance), re-add the syscon compatible string as a fallback. This
works with both older and newer kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable modern fitImage format on sunxi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The make macro to check if the binary exceeds the board size limit is
taken straight from the root Makefile.
Without this and e.g. enabled EFI Vybrid fails booting as the regular
size limit check does not take the final u-boot.imx binary size into
account which is bigger due to alignment as well as IMX header stuff.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
If the function gpr_init is used in a common MX6 spl
implementation we have to ensure that it is only called for
suitable cpu types, otherwise it breaks hardware parts like
enet1, can1, can2, etc.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.de>
The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
With patch 49b23e035d (pci: mvebu: Increase size of PCIe default mapping)
the mapping size for each PCI(e) controller was increased from 32MiB to
128MiB. This leads to problems on boards with multiple PCIe slots / ports
which are unable to map all PCIe ports, e.g. the Armada-XP theadorable:
DRAM: 2 GiB (667 MHz, 64-bit, ECC not enabled)
SF: Detected m25p128 with page size 256 Bytes, erase size 256 KiB, total 16 MiB
Cannot add window '4:f8', conflicts with another window
PCIe unable to add mbus window for mem at f0000000+08000000
Model: Marvell Armada XP theadorable
This patch moves the base address for the PCI(e) memory spaces from
0xe8000000 to the end of SDRAM (clipped to a max of 0xc0000000 right now).
This gives move room and flexibility for PCI(e) mappings.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: VlaoMao <vlaomao@gmail.com>
Tested-by: VlaoMao <vlaomao at gmail.com>
Commit 3c28576bb0 ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
New ACPI assembler issues a warning:
board/intel/edison/dsdt.asl.tmp 13: Offset (0x00),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
Indeed, in the OperationRegion the offset is 0x00 by default.
Thus, drop unneeded Offset() use as suggested by ACPI assembler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Add drivers/net/ti/ folder and move all TI's code in this folder for better
maintenance.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is a large update of the AST2500 SoC DTS file bringing it to the
level of commit 927c2fc2db19 :
Author: Joel Stanley <joel@jms.id.au>
Date: Sat Jun 2 01:18:53 2018 -0700
ARM: dts: aspeed: Fix hwrng register address
There are some differences on the compatibility property names. scu,
reset and clock drivers are also different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the size of the relocation table will be shrunk
to the actual size needed. Although this gives a maximal
space saving, it messes up the _end symbol. This breaks
features like appended DTBs because the _end symbol doesn't
point to the real end of the U-Boot binary.
Remove the size shrinking and make the size of the relocation
table fixed but configurable. This follows the Linux approach
and the user can adjust the size to his needs.
Also rename the relocation table section from .rel to .data.reloc
to follow the Linux approach and to avoid ambiguities with the
.rel.* sections added by the linker.
Reported-by: Lars Povlsen <lars.povlsen@microsemi.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Patch "ARM: rmobile: Mark 4-64GiB as DRAM on Gen3" marked the entire
64bit DRAM space as cachable. On CortexA57, this might result in odd
side effects, where the CPU tries to prefetch from those areas and if
there is no DRAM backing them, CPU bus hang can happen.
This patch fixes it by generating the mem_map structure based on the
actual memory layout obtained from the DT, thus not marking areas
without any DRAM behind them as cachable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: c1ec347638 ("ARM: rmobile: Mark 4-64GiB as DRAM on Gen3")
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Real marketing name of the board was recently updated so
to accommodate that change renaming the board and all
related to it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Using imply for SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION instead of
select ensures we can build without partition support (used to build
a network boot only version of SPL and U-Boot).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Per T1040RM (Rev. 1, 08/2015), there are 2 issues with the RCW EC2
settings.
- The value of FSL_CORENET_RCWSR13_EC2_FM1_GPIO is wrong and should
be 0x04000000 (value of 1 in RCW bit [420:421])
- Value of 2/3 are reserved in RCW bit [420:421], hence there is no
macro FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Per T1040RM (Rev. 1, 08/2015), the value of
FSL_CORENET_RCWSR13_MAC2_GMII_SEL_ENET_PORT is wrong
and should be 0x00000080 (bit 440 in the RCW).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround makes FS as default mode on all affected socs.
Add support to check erratum-A005275 validity for an soc. This info is
required to determine whether a given soc is affected by this erratum.
Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used
to enable workaround for the errata
Force FS mode as default by:
- making EPS as FS
- setting PFSC bit to disable HS chirping
This workaround can be disabled by mentioning "no_erratum_a005275" in
hwconfig string
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner 64-bit SoCs can use 4GiB DRAM chip, however their memory map
has only allocated 3GiB for DRAM, so only 3GiB of the DRAM is
accessible.
Add a Kconfig option for the maximum accessible DRAM.
For A80 it should be a much higher value (8GiB), but as I have no A80
device to test and originally U-Boot only supports 2GiB DRAM on A80, it
currently still falls under the 2GiB situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
All Allwinner 64-bit SoCs now are known to be able to access 3GiB of
external DRAM, however the size of DRAM part in the MMU translation
table is still 2GiB.
Change the size of DRAM part in MMU table to 3GiB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.
Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.
On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since commit 80df194f01 ("x86: detect unsupported relocation types"),
an error message is seen on QEMU x86 target during boot:
do_elf_reloc_fixups32: unsupported relocation type 0x1 at fff841f0, offset = 0xfff00087
do_elf_reloc_fixups32: unsupported relocation type 0x2 at fff841f8, offset = 0xfff00091
Check offset 0xfff00087 and 0xfff00091 in the u-boot ELF image,
fff00087 000df401 R_386_32 00000000 car_uninit
fff00091 000df402 R_386_PC32 00000000 car_uninit
we see R_386_32 and R_386_PC32 relocation type is generated for
symbol car_uninit, which is declared as a weak symbol in start.S.
However the actual weak symbol implementation ends up nowhere. As
we can see below, it's *UND*.
$ objdump -t u-boot | grep car_uninit
00000000 w *UND* 00000000 car_uninit
With this fix, it is normal now.
$ objdump -t u-boot | grep car_uninit
fff00094 w F .text.start 00000001 car_uninit
Reported-by: Hannes Schmelzer <hannes@schmelzer.or.at>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
To allow bigger 64 bit prefetchable PCI regions in Linux, this patch
changes the base address and range of the ACPI area passed to Linux.
BayTrail can only physically access 36 bit of PCI address space. So
just chaning the range without changing the base address won't work
here, as 0xf.ffff.ffff is already the maximum address.
With this patch, a maximum of 16 GiB of local DDR is supported. This
should be enough for all BayTrail boards though.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce a new script to check whether file exists and
use that check in Makefile to avoid break CI system.
The script return 1 when the required files not exists, return 0
when files exists. The script will ignore check to u-boot-dtb.bin,
because if there is something wrong to generate u-boot-dtb.bin,
there must be some code error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We can have the case where u-boot is launched after some other low level
enabler, like for example when u-boot runs after arm-trusted-firmware
and/or optee. So, because of that we may need to jump the initialization of
some IP blocks even because we may no longer have the permission for that.
So, if the config option to skip low level init is set disable also timer,
board and csu initialization.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: u-boot@lists.denx.de
Reviewed-by: Peng Fan <peng.fan@nxp.com>
