VPXA2785(vp-x-a2785-00) is evaluation board which contains two PCIe-Edge
fingers, one for PCIe-B(gen5x8) and one for CPM(dual gen5x8, gen5x16).
Each of the ports can operate in endpoint or root port mode. This allows
the single card to be used for both root port, endpoint, and switch modes.
The board is designed in the similar manner as others Versal boards. It
means board also have ZynqMP Zu4 System Controller which is described in a
separate file.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/59d3b1f7e785bc65518b465e5122fd2787616a93.1695808407.git.michal.simek@amd.com
System controller revC is using ADI ethernet phy instead of TI because of
supply chain issues.
Describe reset assert and de-assert times to 10us and 5ms respectively
according to the datasheet. Also setup RGMII RX and TX delay values to
2400ps as per board bring up observations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2790f6cede7485556d581ab8270dda477fa21522.1695808407.git.michal.simek@amd.com
System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.
All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.
Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).
NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).
i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
Linux requires to describe nand structure under nand controller.
If it is not described nand device is not detected by Linux.
Error shown by Linux kernel:
pl35x-nand-controller e1000000.nand-controller: Incorrect number of NAND chips (0)
pl35x-nand-controller: probe of e1000000.nand-controller failed with error -22
When wired:
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3fcd68ccdfed5e6c079681e3b29e06583ec8a375.1695378830.git.michal.simek@amd.com
The DPSUB DT bindings now specify ports to model the connections with
the programmable logic and the DisplayPort output. Add them to the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1c91420e90bc823d7529834c33438216857c7161.1695378830.git.michal.simek@amd.com
Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/02f308c774d4f2a798a9a8c066824114a19841a7.1695378830.git.michal.simek@amd.com
All zynqmp boards have been already described via mdio node that's why also
convert the rest of the boards. With using mdio node there is an option to
add reset property for the whole mdio bus which is reflected by
's/phy-reset-gpios/reset-gpios/g' for some boards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ff165281a70a38e2b76fee91e6255ce95ce8021b.1695378830.git.michal.simek@amd.com
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all
to required pinctrl nodes to simplify use of the prevent booting on
power plug-in option in SPL.
With the following Kconfig options and nodes in u-boot.dtsi the prevent
booting on power plug-in option can work in SPL.
CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PMIC_RK8XX=y
&i2c0 {
bootph-pre-ram;
};
&rk817 {
bootph-pre-ram;
regulators {
bootph-pre-ram;
};
};
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Add support for generating a LZMA-compressed U-boot binary with the
help of binman, if CONFIG_SPL_LZMA is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for generating a GZIP-compressed U-boot binary with the
help of binman, if CONFIG_SPL_GZIP is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warnings:
<stdout>: Warning (reg_format): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f4000/ethernet@8000000/mdio@f00: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0100:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0000:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (phys_property): /bus@f4000/ethernet@8000000/ethernet-ports/port@2:phys: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move cbass_mcu node to -r5-sk.dts as it is only required
for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmUdaJccHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/ptHxEACdibF5EoRb40qhQCWB
mwW50s76xWOyHGOGjSe3l18zxPdBjQ+9rnT8/A+mjaa8he4kMX9EZJyYRogcz7eR
QcnSeu9Q4L8bKbqnPBOpKF6TN7rFOIUcu+BWp3o8jZ+7/q7OSJrVLsjbXtCuCLnB
q5Pie/in7hmHJsQr6LJ4r31chW6Zm4VDuFiXquuxyE/c94Q8Ue27ag1/RfXL8b/g
Ir9aO+PAldGnVdnhPz4e6PZhzMfCVafw+DR7GVx3Zfnx2bg/dajo38UaLBDdEIS1
EIKONU2CBT/W1kPkLFiz+NdaYCzK9EL+RIbN/iG7ms+ds1+wc3zXpWwqZFASfIod
ZF788Up+wW+3SrKI2ySFjhQroNzDascn+bbHm4yJuAsORqY0XkxjSuWcSz++q8Hs
eMTw/R4uMfEiDvN1A7xlhBMuBrBHk4/6bdCRx2R6nkWes542fsgjXy8tGRWyUgnY
nbpTfYU07N8ck6arZ36KThedD7whJHHRcBYtLjhRG+lKbD0epWy67pXgTr9edTLf
U6ddH+Tndn4qhx067VhZ8vEXTCzypt4lY61MLcM0b9z8S1nJDn8b8jmiii7IR76L
/ocXzuLvNWHfmwNnB2hj/YY+n78vlZhegUxL5/6sH9lNebnewyEzCkVENNELUSYf
8M6vEZprvuhN44Z6hBUWZxXk0w==
=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
stm32mp135f-dk board has a type-c connector to retrieve the connection
state. For now, simply force an active peripheral mode in u-boot for
flashing.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v6.6.rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
commit 6b443faa313c519db755ff90be32758fd9c66453 Linux upstream.
This is a preparation patch for the upcoming support to manage CAN
peripherals in single configuration.
The addition ensures backwards compatibility.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 559a6e75b4bcf0fc9e41d34865e72cf742f67d8e Linux upstream.
Add pin configurations for using CAN controller on stm32f469-disco
board. They are located on the Arduino compatible connector CN5 (CAN1)
and on the extension connector CN12 (CAN2).
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230328073328.3949796-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7355ad1950f41e755e6dc451834be3b94f82acd4 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F429. The
chip contains two CAN peripherals, CAN1 the primary and CAN2 the secondary,
that share some of the required logic like clock and filters. This means
that the secondary CAN can't be used without the primary CAN.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230328073328.3949796-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 10a970bc3ebfa ("ARM: dts:
stm32: support display on stm32f746-disco board") and removes the same
settings from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit e4e724099f04072053cf411456e3e9aae48c4af1 Linux upstream.
In the schematics of document UM1907, the power supply for the micro SD
card is the same 3v3 voltage that is used to power other devices on the
board. By generalizing the name of the voltage regulator, it can be
referenced by other nodes in the device tree without creating
misunderstandings.
This patch is preparatory for future developments.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 008ef8b3a1a00 ("Add LTDC
(Lcd-tft Display Controller) support") and removes the same settings
from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit f0215440069c4fb12958d2d321e05faa2708a11d Linux upstream.
The patch adds support for touchscreen on the stm32f746-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7a5f349e592c254f3c1ac34665b6c3905576efc2 Linux upstream.
The patch replaces the number 12 with the appropriate numerical constant
already defined in the file stm32f7-rcc.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 0920ccdf41e3078a4dd2567eb905ea154bc826e6 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
* CAN1: Primary bxCAN for managing the communication between a secondary
bxCAN and the 512-byte SRAM memory.
* CAN2: Secondary bxCAN with no direct access to the SRAM memory.
This means that the two bxCAN cells share the 512-byte SRAM memory and
CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
* CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
512-byte SRAM memory.
-------------------------------------------------------------------------
| features | CAN1 | CAN2 | CAN 3 |
-------------------------------------------------------------------------
| SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte |
-------------------------------------------------------------------------
| Filters | 26 filters shared between CAN1 & CAN2 | 14 filters |
-------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 011644249686f2675e142519cd59e81e04cfc231 Linux upstream.
Add pin configurations for using CAN controller on stm32f7.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize RZ R8A774E1 RZ/G2H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774C0 RZ/G2E DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774B1 RZ/G2N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774A1 RZ/G2M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Synchronize RZ R7S72100 RZ/A1 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77995 D3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77980 V3H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77965 M3-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77951 H3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7794 E2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7790 H2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
Trying to boot a fitImage after a successful hab_auth_img operation
causes the following error:
## Loading kernel from FIT Image at 88000000 ...
Using 'conf-imx7d-smegw01.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x8800010c
Data Size: 9901752 Bytes = 9.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80800000
Entry Point: 0x80800000
Hash algo: sha256
Hash value: 28f8779bbf010780f16dd3d84ecb9b604c44c5c2cf7acd098c264a2d3f68e969
Verifying Hash Integrity ... sha256Error in SEC deq
CAAM was not setup properly or it is faulty error!
The reason for this error is that the BootROM uses the CAAM Job Ring 0,
so disable its node in U-Boot to avoid the resource conflict.
imx8m dtsi files also have the Job Ring 0 disable since the following
kernel commit:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch?h=v6.5&id=dc9c1ceb555ff661e6fc1081434600771f29657c
For a temporary solution, disable the Job Ring 0 in imx7s-u-boot.dtsi.
Reported-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Correct the i2c address for si570 oscillator that generates the si570_user1
clock. i2c address was changed by commit b6a8c603d680 ("arm64: zynqmp: Fix
i2c addresses for vck190 SC") because address in node name wasn't aligned
with reg property. But actual 0x5f address is correct which is quite rare
because all other si570s are at 0x5d.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6f31881b0e2dd657f0d4ff0869c009c2e1224f22.1694441445.git.michal.simek@amd.com
Added no-wp DT property in OSPI flash node for all board dts & dtsi files
on which the WP# signal of the OSPI flash device is not connected. If this
property is set, then the software will avoid setting the status register
write disable (SRWD) bit in status register during status register
write operation.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e88dd7b9306bdf0738b2248bf9017e1997d25dc.1694441445.git.michal.simek@amd.com
xlnx,mio_bank was used in past but it was renamed to xlnx,mio-bank because
'_' in property shoudln't be used. There is no impact on the platform
because if the properly is not defined bank 0 is default. Bank 0 and 1 have
the same configuration that's why there shouldn't be any issue.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ace68d4b7701d1606a85cb18242409fce941b363.1694441445.git.michal.simek@amd.com
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
Revision 2 is SW compatible with revision 1 but it is necessary to reflect
it in model and compatible properties which are parsed by user space.
Rev 2 has improved a power on boot reset and MIO34 shutdown glich
improvement done via an additional filter in the GreenPak chip.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6b9e68ebfb436da391daeb147f2a9985ac984c0c.1692951005.git.michal.simek@amd.com
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c052ddf39e392e97f87f1c57ea06f3508733c672.1692947486.git.michal.simek@amd.com
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
NOTE: sync with v6.6-rc1 will bring in this change naturally.
Signed-off-by: Nishanth Menon <nm@ti.com>
Introduce the new serdes header from kernel v6.6-rc1
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Signed-off-by: Nishanth Menon <nm@ti.com>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To have the WDIOF_CARDRESET support for the TI AM65x platform watchdog,
this patch reserves some memories, which indicate if the current boot due
to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Update the DDR settings to those generated using 0.10 version of Jacinto
7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
baseline of base device tree is v6.5-rc1.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Add a newline at the end of the dts, without which the build fails
when including a dtsi file.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Button works out of the box now if the following config options are
enabled: CONFIG_BUTTON, CONFIG_BUTTON_GPIO, CONFIG_CMD_BUTTON,
CONFIG_DM_GPIO.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
If CONFIG_LED and CONFIG_LED_GPIO are enabled, it is not necessary to
initialize the RGB LED on the board by manually setting hardcoded GPIOs
anymore. Everything is well defined in dts and can be used like on
boards of other vendors.
Keep the old behaviour as fallback, though.
With all this in place enabling CONFIG_CMD_LED gives us a working 'led'
command on the U-Boot shell.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Adding a phandle to a template node is not allowed, since when the node is
instantiated multiple times, we end up with duplicate phandles.
Drop this invalid constructs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
CFG_STM32MP1_SCMI_SHM_SYSRAM will be disabled by default for STM32MP13x
SoCs in next OP-TEE version and the OP-TEE SMCI server uses the OP-TEE
native shared memory registered by clients.
To be compatible by default with this configuration this patch removes
the shared memory in the SCMI configuration and the associated reserved
memory in SRAM.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since OP-TEE commit 89ba3422ee80 ("plat-stm32mp1: scmi_server: default
use OP-TEE shared memory"), integrated in OP-TEE 3.22.0-rc1
the default configuration for STM32MP15x SoCs changes,
CFG_STM32MP1_SCMI_SHM_SYSRAM is disabled by default and the OP-TEE SMCI
server uses ithe OP-TEE native shared memory registered by clients.
To be compatible by default with this configuration and the next OP-TEE
version, this patch removes the SHMEM in the SCMI configuration and the
associated reserved memory in the last 4KByte page of SRAM,
in the STM32MP15 device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
MT7988 has a t-phy and an x-phy controller. There is already a driver for
t-phy so we can add USB support for this phy type.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi.
Need to delete clock & power domain properties of
main_timer1 in -r5.dts else won't boot. This is because
timer_init is done during rproc_start to start System Firmware,
but we can't do any clock/power-domain operations before
System Firmware starts.
- same constraint applies to main_uart0
- drop cpsw3g custom DT property 'mac_efuse' and custom
DT node cpsw-phy-sel as driver picks these from standard
property/node.
- include board dts file in -r5 dts file to avoid duplication
of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This reverts commit 28a4c31134.
This node should be in the board DT file and should come from upstream.
Moreover, this PMIC is no present on all variants of am642-sk
and will need a separate board DT file.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com> #SK-AM64B
The DHCOM SoM has two options for supplying ETHRX clock to the DWMAC
block and PHY. Either (1) ETHCK_K generates 50 MHz clock on ETH_CLK
pad for the PHY and the same 50 MHz clock are fed back to ETHRX via
internal eth_clk_fb clock connection OR (2) ETH_CLK is not used at
all, MCO2 generates 50 MHz clock on MCO2 output pad for the PHY and
the same MCO2 clock are fed back into ETHRX via ETH_RX_CLK input pad
using external pad-to-pad connection.
Option (1) has two downsides. ETHCK_K is supplied directly from either
PLL3_Q or PLL4_P, hence the PLL output is limited to exactly 50 MHz and
since the same PLL output is also used to supply SDMMC blocks, the
performance of SD and eMMC access is affected. The second downside is
that using this option, the EMI of the SoM is higher.
Option (2) solves both of those problems, so implement it here. In this
case, the PLL4_P is no longer limited and can be operated faster, at
100 MHz, which improves SDMMC performance (read performance is improved
from ~41 MiB/s to ~57 MiB/s with dd if=/dev/mmcblk1 of=/dev/null bs=64M
count=1). The EMI interference also decreases.
Ported from Linux kernel commit
73ab99aad50cd ("ARM: dts: stm32: Switch DWMAC RMII clock to MCO2 on DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v6.4.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As reported by the datasheet (DocID027590 Rev 4) for PG12:
- AF9 -> LCD_B4
- AF14 -> LCD_B1
So replace AF14 with AF9 for PG12 in the dts.
Fixes: fe63d3cfb7 ("ARM: dts: stm32: Sync DT with v4.20 kernel for stm32f7")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Make device tree complete and consistent for pre relocation phase. Some
nodes are missing, causing warnings to be issued on serial port probing
during pre relocation phase (uclass_get_device_by_phandle_id fails when
called by pinctrl_select_state_full: none of these failures is fatal
nor causing issues). Add to *-u-boot.dtsi all required nodes with the
'bootph-some-ram' attribute.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support to read RK3308 registers used to configure UART clocks, and
thus to get UART rate and baudrate. This fixes clock_get_rate returning
error on serial device probing. Moreover, there is no need anymore to
use 'clock-frequency' property for UART nodes in *-u-boot.dtsi files
for all cases where UART is not inited by U-Boot proper or by SPL o by
TPL code but by a preliminary external boot phase (for Rock PI S, UART
is inited by external TPL).
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Most board device trees for RK356x set max-frequency = <200000000> in
the sdhci node, some boards like Quartz64 do not. This result in an
error message due to sdhci driver trying to set a clock rate of 0
instead of the max-frequency value.
rockchip_sdhci_probe clk set rate fail!
Fix this by setting a common max-frequency in rk356x-u-boot.dtsi. A
patch to set default max-frequency of sdhci node in linux is planned.
Also remove the forced status = "okay" for the sdhci and sdmmc0 nodes,
boards already set correct state for these nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Align the SPI flash entry with upstream. There's no need
to diverge here.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rk3328 rng details to the u-boot.dtsi and
enable the RNG on the Rock64 to be able to provide
a random seed via UEFI.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Fix typo message)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Fix rcfg_yaml to really point to rm-cfg.yaml and pcfg_yaml to really
point to pm-cfg.yaml which likely is the intention.
While at it also add labels for the remaining items like custmpk_pem,
dkey_pem, bcfg_yaml_sysfw, scfg_yaml_sysfw, pcfg_yaml_sysfw and
rcfg_yaml_sysfw.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
On Ten64 boards, the "serial number" is the MAC address of the
first Gigabit Ethernet interface (labelled GE0 on the appliance),
and counted up from there.
The previous logic did not take into account U-Boot's ordering
of the network interfaces. By setting aliases/ethernetX in the device
tree we can ensure the U-Boot 'ethX' is the same as the labelled
port order on the unit, as well as the one adopted by Linux.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This patch adds general board files based on MT7988 SoCs.
MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:
1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7988 SoC.
This includes files that will initialize the SoC after boot and
its device tree.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Now that individual 2.5Gbps SGMII support has been added to
mtk-eth, all boards that use 2.5Gbps link with mt7531 must be
converted to use "2500base-x" instead of "sgmii".
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Now we use fdtdec_setup_mem_size_base() to get DRAM base from fdt ram node
and update gd->ram_base. CFG_SYS_SDRAM_BASE is unused and will be removed.
Also, since mt7622 always passes fdt to linux kernel, there's no need to
assign value to gd->bd->bi_boot_params.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Basically the same as on sam9x60-ek. Same as in Linux. NAND flash is
correctly detected when booting into U-Boot:
U-Boot 2023.07-rc6-00005-g12719f75dc-dirty (Jul 05 2023 - 13:06:35 +0000)
CPU: SAM9X60 128MiB DDR2 SiP
Crystal frequency: 24 MHz
CPU clock : 600 MHz
Master clock : 200 MHz
Model: Microchip SAM9X60 Curiosity
DRAM: 128 MiB
Core: 145 devices, 22 uclasses, devicetree: separate
NAND: 512 MiB
MMC: sdhci-host@80000000: 0, sdhci-host@90000000: 1
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@f802c000
Hit any key to stop autoboot: 0
Signed-off-by: Alexander Dahl <ada@thorsis.com>
- nodes moved
- using node references by label instead of dulicating the node tree
Makes it easier to compare with the dts file from Linux kernel.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The user guide says it's a Microchip 24AA025E48 serial EEPROM, which is
a 2-Kbit I2C Serial EEPROM with EUI-48™ Identity. This is the chip
actually populated on board EV40E67A rev 4.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
No functional changes, but this:
- reorder nodes (ordered by memory offset as in Linux)
- add label to pinctrl node name for easier reference in board files
- fix whitespace
Diff to sam9x60.dtsi in Linux is much better readable now.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
rk3328-xhci has been added due to the fact that the upstream
dwc3 is unsupported. Moreover, the driver for rk3328-xhci is
not added to the code tree.
By considering these facts and unsupported rk3328-xhci this
patch is dropping all related code from DT. However, the DWC3
is fixed now in dwc3-generic and RK3328 USB 3.0 is functional
in upcoming patches.
Let's drop it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).
Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move bootph-all prop to common SoC dt file, because they are typically used
by multiple boards.
Unreferenced nodes are removed from the SPL device tree during a
normal build.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pcie pinctrl override added in the commit a76aa6ffa6 ("rockchip:
rk3568-rock-3a: Enable PCIe and NVMe support") is causing a pinmux issue
on linux when using a EFI boot flow.
The pcie reset-gpios must however be configured with gpio function, or
the device will freeze running pci enum and nothing is connected.
Adjust the pinctrl override in u-boot.dtsi to fix this issue. PCIe/NVMe
continues to work in both U-Boot and linux after this change.
Also revert disable of sdmmc2 and uart1 to fix use of wifi in linux when
using a EFI boot flow.
Fixes: a76aa6ffa6 ("rockchip: rk3568-rock-3a: Enable PCIe and NVMe support")
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.
Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.
Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootRom will try to load TPL+SPL from media in the following order:
- SPI NOR Flash
- SPI NAND Flash
- NAND Flash
- eMMC
- SDMMC
SPL will try to load FIT from media in the order defined in the device
tree u-boot,spl-boot-order property.
Change the default order to load FIT from to:
- same media as TPL+SPL
- SDMMC
- eMMC
Boards with strict load order requirements should override the
u-boot,spl-boot-order property in the board specific u-boot.dtsi.
Fixes: 42f67fb51c ("rockchip: rk3568: Fix boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to common pinctrl nodes for eMMC, FSPI, SD-card and
UART2 that are typically used by multiple boards. Unreferenced nodes are
removed from the SPL device tree during a normal build.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove regulator-boot-on prop from regulators now that the phy core has
support for phy-supply after the commit c57e0dcd93 ("phy: add support
for phy-supply").
This reverts commit 7911f409ff.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-veyron-speedy-u-boot.dtsi file duplicates the bootphase dts
fragments from rk3288-veyron-u-boot.dtsi even though it #inclues that.
Deduplicate these into the latter file, which should also make the eMMC
available to the other veyron boards' SPL.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.
Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ROCK Pi S SKU/models are not equipped with SD-NAND (eMMC),
therefore SPL needs access to sdmmc: add it to rk3308-u-boot.dtsi
with bootph-all property.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update config, IO and memory regions used based on [1] with pcie3x2
config reg address and reg size corrected.
Before this change:
PCI Autoconfig: Bus Memory region: [0-3eefffff],
PCI Autoconfig: Bus I/O region: [3ef00000-3effffff],
After this change:
PCI Autoconfig: Bus Memory region: [40000000-7fffffff],
PCI Autoconfig: Bus I/O region: [f0100000-f01fffff],
[1] https://lore.kernel.org/lkml/20221112114125.1637543-2-aholmes@omnom.net/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.
Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prepare for ROCK 4 SE support, changes are needed to the common ROCK
Pi 4 devicetree to move the OPP from the common devicetree to individual
board devicetrees. Sync the Rockchip RK3399 ROCK Pi 4-related DTs from
Linux to gain from these changes.
Kernel tag: next-20230719
Kernel commits:
cfa12c32b96f ("arm64: dts: rockchip: correct wifi interrupt flag in Rock \
Pi 4B")
cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
2bd1d2dd808c ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+")
fd2762a62646 ("arm64: dts: rockchip: Move OPP table from ROCK Pi 4 dtsi")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_OPTEE_IMAGE option is used during DRAM size detection for
Rockchip ARM platform to indicate that an OP-TEE binary was already loaded
and a Trusted Execution Environment (TEE) is available in order to
block/reserve a memory-region for it.
This adds a bunch of new `#if's` to u-boot-rockchip.dtsi to include the
OP-TEE binary in the FIT image for ARM SOCs if CONFIG_SPL_OPTEE_IMAGE is
selected.
That makes it a little harder to read, but I opted for that, because all
the duplicates in an extra ARM-OP-TEE-specfic .dtsi would be the greater
evil, IMHO. Besides it's more likley being "forgotten" to sync when changes
in u-boot-rockchip.dtsi are made.
The no longer required rockchip-optee.dtsi and it's inclusions are dropped.
The hardcoded load address is common across all OP-TEE implemenations for
Rockchip (vendor and upstream).
The OP-TEE-binary is non-optional if CONFIG_SPL_OPTEE_IMAGE is selected and
there will be an error if the file does not exist and/or `TEE=` build
option is missing.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk3588j-u-boot.dtsi for adding U-Boot specific nodes and
properties for Rockchip RK3588J SoC.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3588J is the industrial-grade version of RK3588 SoC and
is operated with -40 °C to +85 °C temparature.
Add rk3588j specific dtsi for adding rk3588j specific operating points
and other changes to be add in future.
Kernel commit:
commit <8274a04ff1dc> ("arm64: dts: rockchip: Add Rockchip RK3588J")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Add support for the DSI and DSI-DPHY to U-Boot for the RGxx3. These are
needed so we can send a panel ID request to determine which panel is
being used.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinctrl on the Anbernic RGxx3 for the i2c2 bus does not use the
default value, so explicitly define it.
Fixes: 6cf6fe2537 ("board: rockchip: add Anbernic RGXX3 Series Devices")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the USB3.0 host node, and gadget node.
The gadget is available through the USB type C connector on the board.
The connector is tied to a Fairchild fusb302b device, which currently
does not have a driver in U-boot, but the node is here for correct
description of the board + Linux future compatibility.
It will be easier to move the node as-is when it will be available
in the DT from Linux
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the USB 3.0 devices in rk3588:
- USB DRD(dual role device) 3.0 #0 as usbdrd3_0 which is available in
rk3588s
- USB DRD(dual role device) 3.0 #1 as usbdrd3_1 which is available in
rk3588 only
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #0 phy interface
as usbdp_phy0
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #1 phy interface
as usbdp_phy1
- USB 2.0 phy #2 , the USB 3.0 device can work with this phy in USB 2.0
mode
- associated GRFs (general register files) for the devices.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: move nodes to right place, adapt from latest
linux kernel]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the devicetree with linux-next tag: next-20230525
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FIT signature requires the updates to u-boot.dtb and the DTB that we
pack don't get updates with the changes of the signature node.
Pack u-boot.dtb as the default DTB so that the signature node changes
can be reflected in them.
(Note, this is only packaging the primary platform and the secondary
platform will require manual changes for the FIT signature enablement)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[ add additional boards that were missing ]
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move to using binman to generate tispl.bin which is used to generate the
final flash.bin bootloader for iot2050 boards.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
By providing entries in the binman node of the device tree, binman will
be able to find and package board config artifacts generated by
TIBoardConfig with sysfw.bin and generate the final image sysfw.itb.
It will also pick out the R5 SPL and sign it with the help of TI signing
entry and generate the final tiboot3.bin.
Entries for A72 build have been added to k3-j721e-binman.dtsi to
generate tispl.bin and u-boot.img.
Support has been added for both HS-SE(SR 1.1), HS-FS(SR 2.0) and GP images
In HS-SE, the encrypted system firmware binary must be signed along with
the signed certificate binary.
HS-SE:
* tiboot3-j721e_sr1_1-hs-evm.bin
* sysfw-j721e_sr1_1-hs-evm.itb
* tispl.bin
* u-boot.img
HS-FS:
* tiboot3-j721e_sr2-hs-fs-evm.bin
* sysfw-j721e_sr2-hs-fs-evm.itb
* tispl.bin
* u-boot.img
GP:
* tiboot3.bin -->tiboot3-j721e-gp-evm.bin
* sysfw.itb --> sysfw-j721e-gp-evm.itb
* tispl.bin_unsigned
* u-boot.img_unsigned
It is to be noted that the bootflow followed by J721E requires:
tiboot3.bin:
* R5 SPL
* R5 SPL dtbs
sysfw.itb:
* TIFS
* board-cfg
* pm-cfg
* sec-cfg
* rm-cfg
tispl.bin:
* DM
* ATF
* OP-TEE
* A72 SPL
* A72 SPL dtbs
u-boot.img:
* A72 U-Boot
* A72 U-Boot dtbs
Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Board config binary artifacts must be generated to be used by binman to
package sysfw.itb and tiboot3.bin for all K3 devices.
For devices that follow combined flow, these board configuration
binaries must again be packaged into a combined board configuration
blobs to be used by binman to package tiboot3.bin.
Add common k3-binman.dtsi to generate all the board configuration
binaries needed.
Also add custMpk.pem and ti-degenerate-key.pem needed for signing GP and
HS bootloader images common to all K3 devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
