Unselect CONFIG_CONSOLE_MUX to fix the following
error for the input, output and error interfaces:
U-Boot 2023.10 (Oct 03 2023 - 21:23:18 -0300)
...
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes prototype rev.100 SoM,
update the DT to describe production rev.200 SoM which brings the
following changes:
- Fast SoC GPIOs exposed on the SoM edge connector
- Slow GPIOs like component resets moved to I2C GPIO expander
- ADC upgraded from TLA2024 to ADS1015 with conversion interrupt
- EEPROM size increased from 256 B to 4 kiB
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
The RD-AC5X doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 27f60f020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This reverts commit 5c1c6b7306. The reason
for switching to i2c-gpio was due to an issue we were seeing in the
Linux kernel where the CPU would lock up on certain adverse I2C bus
conditions. We were never able to reproduce the lockup in U-Boot but
assumed that was probably just luck.
Since then we have discovered that the lock up was due to the I2C
transaction offload engine in the I2C controller not coping with the
adverse bus conditions (basically it thinks there's another master and
waits for a STOP condition that never comes). U-Boot doesn't use the I2C
offload feature so is not susceptible to the lockup.
We can therefore safely return to using the built-in I2C controller.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 23f60c020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When using a list of writeable variables, the initial values come
from the built-in default environment since commit 5ab8105836 ("env:
Complete generic support for writable list").
Remove unnecessary misuse of CONFIG_ENV_IS_NOWHERE as default environment.
Based on the fix done by commit b16fd7f75f ("imx6q: acc: Remove misuse
of env is nowhere driver").
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Use DM_I2C and DM_SERIAL as it is now mandatory.
Signed-off-by: Andrej Rosano <andrej.rosano@withsecure.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable USB SDP SPL aka serial downloader recovery mode support.
While at it also enable fastboot support which may be used to
subsequently load further stages like a Toradex Easy Installer FIT
image.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.
The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- RGMII PHY
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW73xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- on-board 802.11abgnac 1x1 WiFi and Bluetooth 5.2
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 2x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW72xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 1x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
The malloc capacity in DRAM at R5 SPL is set to 1MB which isn't
sufficient to load the new tispl.bin to
enable loading of tispl.bin the size is increased by 256KB to 1.25MB.
Cc: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Currently we have all drivers for use USB stack on A1-series
SoC's. Let's enable USB options for the Amlogic AD401 reference A1
SoC board.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-9-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. This makes
the defconfigs that make use of PPA obsolete, so remove them.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[Merged part 1 and part 2]
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Allow for a proper configuration of CFI flash banks avaialble on the vexpress_ca9x4
board. Without this option, the CFI flash incorrectly detects that the board has two
banks of 32MB flash devices, while in reality, the board provides
two flash banks, each with 64MB size. As a result, it becomes impossible to e.g. to
save u-boot env in flash. According to device tree for this board and
its implementation in QEMU, the CFI width should be set to 32 bits.
After applying this fix, CFI flash will correctly detect both flash
banks each with a size of 64MB. As as result the functionality of e.g. saving u-boot
env will work correctly.
Tested on QEMU 6.2.0.
Cc: Kristian Amlie <kristian.amlie@northern.tech>
Signed-off-by: Patryk Biel <pbiel7@gmail.com>
Reviewed-by: Kristian Amlie <kristian.amlie@northern.tech>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
With PMIC_RK8XX, SYSRESET and CMD_POWEROFF options enabled it is
possible to power down a board using the poweroff command and turn the
board back on using a power button.
Enable the poweroff command on RK356x boards that have a button wired
to PMIC pwron.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Without DOS_PARTITION support U-Boot is not able to boot an OS stored
into an SD card with MBR partitions table. This is still a quite common
case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip
RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are
the only RK boards missing of DOS_PARTITION.
Reported-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK3588 boards that
have an enabled gmac node and drop ETH_DESIGNWARE and GMAC_ROCKCHIP for
remaining RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK356x boards that
have an enabled gmac node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
Kernel commit d93036b47f35 ("arm64: dts: ti: k3-j721e-mcu_wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----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=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Activate the command stm32prog with CONFIG_CMD_STM32MPROG.
The CONFIG_SET_DFU_ALT_INFO is also activated to support
the required weak functions for the DFU virtual backen defined in
board/st/common/stm32mp_dfu.c.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Default embed this configuration. If OP-TEE PTA RNG is exposed, it means
that the RNG is managed by the secure world. Therefore, the RNG node
should be disabled in the device tree as an access would be denied
by the hardware firewall.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the RNG driver as it is usable by other STM32 platforms
than the STM32MP1x ones. Rename CONFIG_RNG_STM32MP1 to
CONFIG_RNG_STM32
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch removes the legacy mode of displaying the ST logo and adopts
the approach introduced by the commit 284b08fb51 ("board: stm32mp1: add
splash screen with stmicroelectronics logo").
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The patch removes the legacy mode of displaying the ST logo and adopts
the approach introduced by the commit 284b08fb51 ("board: stm32mp1: add
splash screen with stmicroelectronics logo"). It was necessary to use a
specific logo for the stm32f746-disco board.
Furthermore, the previous version didn't properly center the logo, hiding
its upper part.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch fixes the y-resolution, which was causing the creation of a
framebuffer larger than actually needed, resulting in memory waste.
Fixes: cc1b0e7b8e ("board: Add display to STM32F746 SoC discovery board")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Powering off the SiFive HiFive Unmatched board is supported both via the
SBI and GPIO sysreset drivers. See device-tree entry
compatible = "gpio-poweroff".
Enable the poweroff command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set U-Boot environment storage eMMC device number to 0, to match
the new additions to DT /aliases node pulled in alongside Linux
6.5.3 DT synchronization.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 65cc0e2a65 ("global: Move remaining CONFIG_SYS_* to CFG_SYS_*")
renamed CONFIG_SYS_UBOOT_START to CFG_SYS_UBOOT_START. Unfortunately,
this meant that the value was no longer available to the Makefile. This
caused imxrt to fail to boot. All the other boards that used this
variable were unaffected because they were using the default value
which is CONFIG_TEXT_BASE.
This commit converts CFG_SYS_UBOOT_START to Kconfig and sets the default
value to CONFIG_TEXT_BASE.
Suggested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We only have serial as console option, and leaving this on turns on
SYS_CONSOLE_IS_IN_ENV which is also not true for these devices, leaving
an ugly
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
behind.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
CONFIG_SYS_BOOT_LOCKED means that a restricted boot environment will
be used. In this case, hab_auth_img_or_fail should be called to prevent
U-Boot to continue running when the fitImage authentication fails.
Fix the logic accordingly.
Additionally, select CONFIG_SYS_BOOT_LOCKED by default.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Set CONFIG_SYS_LOAD_ADDR=0x88000000 and use this address for
loading fitImage.
Also pass the standard CONFIG_BOOTFILE option to indicate
the fitImage file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
commit 280f45d239 ("configs: get rid of build warnings due to
SPL_USB_DWC3_GENERIC") missed enabling DWC3 glue layer for
usbmsc_defconfig and this broke boot from USB mass storage.
Fix this by enabling DWC3 glue layer.
Fixes: 280f45d239 ("configs: get rid of build warnings due to SPL_USB_DWC3_GENERIC")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
At least on modern machines the write-back mechanism for the frame buffer
is quite slow when scrolling, since it must read the entire frame buffer
and write it back.
Enable the VIDEO_COPY feature to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These two builds are similar but have some different options for not good
reason. Line them up to be as similar as possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The debug UART on modern machines uses a 32-bit wide transfer. Without
this, setting debug output causes a hang or no output. It is not obvious
(when enabling CONFIG_DEBUG_UART) that this is needed.
Enable 32-bit access to avoid this trap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If coreboot does not set up sysinfo for the UART, SPL currently hangs.
Use the DBG2 technique there as well. This allows coreboot64 to boot from
coreboot even if the console info is missing from sysinfo
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable bootstd options and provide instructions on how to boot a linux
distro using coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add these options to permit access to more disk types.
Add some documentation as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make sure that CONFIG_X86_OFFSET_U_BOOT is the same as CONFIG_TEXT_BASE
as it is changing CONFIG_X86_OFFSET_U_BOOT
Samus boots into U-Boot proper in flash, not RAM. Also expand the SPL
malloc() size a little, to avoid an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable bootstd support for U-Boot at VirtualBox described at
https://source.denx.de/u-boot/u-boot/-/blob/master/doc/develop/bootstd.rst
This is used to boot system images at Virtualbox via
- distroboot (extlinux.conf)
- boot script
Signed-off-by: Thomas Mittelstaedt <thomas.mittelstaedt@bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Added 'efi-payload64' tag]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot at VirtualBox must load Linux and boot configuration from disk devices.
Here the discs at AHCI (scsi) bus are used to load the needed boot data.
Signed-off-by: Thomas Mittelstaedt <thomas.mittelstaedt@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Added 'efi-payload64' tag and rebased on top of u-boot/master]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When CONFIG_CMD_USB and CONFIG_USB are disabled, still some compilation
errors are seen as below.
In file included from include/configs/xilinx_zynqmp.h:173,
from include/config.h:3,
from include/common.h:16,
from env/common.c:10:
include/config_distro_bootcmd.h:302:9: error: expected '}' before 'BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:302:9: note: in definition of macro
'BOOTENV_DEV_NAME_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:77:41: note: in expansion of macro
'BOOTENV_DEV_NAME'
77 | # define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
func(USB, usb, 1)
| ^~~~
include/configs/xilinx_zynqmp.h:168:9: note: in expansion of macro
'BOOT_TARGET_DEVICES_USB'
168 | BOOT_TARGET_DEVICES_USB(func) \
| ^~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:454:25: note: in expansion of macro
'BOOT_TARGET_DEVICES'
454 | "boot_targets=" BOOT_TARGET_DEVICES(BOOTENV_DEV_NAME) "\0"
| ^~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:474:9: note: in expansion of macro
'BOOTENV_BOOT_TARGETS'
474 | BOOTENV_BOOT_TARGETS \
| ^~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:179:9: note: in expansion of macro
'BOOTENV'
179 | BOOTENV
| ^~~~~~~
include/env_default.h:120:9: note: in expansion of macro
'CFG_EXTRA_ENV_SETTINGS'
120 | CFG_EXTRA_ENV_SETTINGS
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from env/common.c:32:
include/env_default.h:27:36: note: to match this '{'
27 | const char default_environment[] = {
| ^
scripts/Makefile.build:256: recipe for target 'env/common.o' failed
make[1]: *** [env/common.o] Error 1
Makefile:1853: recipe for target 'env' failed
make: *** [env] Error 2
make: *** Waiting for unfinished jobs....
Add CONFIG_USB_STORAGE as dependency for USB related macro's such as
BOOT_TARGET_DEVICES_USB() and DFU_DEFAULT_POLL_TIMEOUT and
CONFIG_THOR_RESET_OFF.
Remove CONFIG_ZYNQMP_USB from Kconfig and also from defconfig since it
is not used anywhere else.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230904031528.11817-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data
structures at a random address at each boot.The bootloader
supports randomizing the virtual address at which the kernel image
is loaded. The bootloader must provide entropy by passing a random
u64 value in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831031658.2203-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831032612.2729-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230824032712.13399-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
HBM stands for high bandwidth memory and is a type of memory interface used
in 3D-stacked DRAM (dynamic random access memory) in some AMD GPUs (aka
graphics cards), as well as the server, high-performance computing (HPC)
and networking and client space. High Bandwidth Memory(HBM) has total 16
channels, one channel is divided into two pseudo channels which makes its
32 banks each with some amount of memory.
And then we have DDR_LOW PS low, DDR_HIGH0 PS high, DDR_HIGH1 PS very high
and pretty much there should be also place for PL DDR. So maximum number of
memory banks will be 36, updating the CONFIG_NR_DRAM_BANKS to 36.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ed9eaf5c20501ee691d7d28a173511cd9a87f161.1690958095.git.michal.simek@amd.com
Enable CONFIG_OF_BOARD_SETUP, so we could use ft_board_setup() to fixup
memory size passed to kernel.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Switch sandbox to DM_USB_GADGET, DM is the future.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Enable UFS controller driver and matching UFS and SCSI commands. The
former is used to initialize the device, the later is used to perform
low level access to the SCSI interface of the UFS device.
Enable R8A779F0 S4 Spider specific dependencies, the PCA953x driver
and GPIO clock gate driver. This setup is used to toggle 38.4 MHz
clock for the UFS controller.
Enable support for 48bit LBA in block layer to address disks larger
than 512*2^32 ~= 144 PiB. Enable use of 64bit LBA variables in the
rest of U-Boot, instead of the default 32bit ones.
Increase FAT cluster size to 128k as that is what is used by the
filesystem that is populated on the UFS device.
Use 'ufs init && scsi scan' to start the UFS device from U-Boot prompt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
At this point, system shutdown is not supported by the DM firmware
that TF-A calls. As we can't de-select only this feature[1], declare
complete PSCI reset support as non-functional so that we don't signal
incomplete support to the OS via EFI runtime services. This makes
power-off under Linux work again when booting via EFI.
[1] https://uefi.org/specs/UEFI/2.9_A/08_Services_Runtime_Services.html?highlight=efiresetshutdown#resetsystem
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Suggested-by: Tom Rini <trini@konsulko.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
legacy image format support. This fixes ut_bootstd_bootflow_cmd_menu
test.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
SPL_SYS_MALLOC_CLEAR_ON_INIT would enable SYS_MALLOC_CLEAR_ON_INIT by
default, but that's not need on JH7110, so disable that.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Although PCIE driver already exists, board defconfig isn't configured to
enable PCIE enum on boot, thus USB storage device and NVME drive are not
supported by default. So modify defconfig to enable PCIE auto enum, then
start USB subsystem and scan nvme drive on boot.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
This platform is behind on migrations (it is the sole user of the oldest
legacy version of the USB gadget stack and is long overdue for
migration) and with Pali no longer being a maintainer, we remove this
platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
Select the i.MX8MM thermal driver as it is useful for displaying
the CPU temperature and its grading:
CPU: Commercial temperature grade (0C to 95C) at 38C
It also prevents booting when the temperature is above the alert
point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot splits DRAM bank spanning addresses below and above the 32bit
boundary into two DRAM banks. Since this platform may come with 4GiB
of DRAM, increase the DRAM bank count to 2.
Signed-off-by: Marek Vasut <marex@denx.de>
This board certainly does use default 'run distro_bootcmd' boot command,
make sure this is set in 'bootcmd' variable.
Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable this option to reclaim some space, since bootstd requires less
functionality to operate (e.g. hush parser).
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop use of the distro scripts and use standard boot instead.
We don't need to specify the mmc devices individually, since they are
used in order from 0 to 2, and standard boot uses that order anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Add the path to the public key EFI Signature List(ESL) file for the
sandbox variants which enable capsule authentication. This ESL file
gets embedded into the platform's device-tree as part of the build.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Enable the EFI capsule update code on all sandbox variants. This was
already enabled on the sandbox, sandbox64 and sandbox_flattree
variants. The rest of the variants also have the EFI capsule update
module enabled now. With this commit, the mkeficapsule tool also gets
enabled on all variants.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 61040097a9 ("reset: at91: Add reset driver for basic
assert/deassert operations") the compatible "microchip,sam9x60-rstc" for
the sam9x60 reset controller in sam9x60.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now. This
resulted in the following error message, when trying to reset from
U-Boot shell:
U-Boot> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fixed by enabling the new driver in the relevant defconfigs. Tested on
sam9x60-curiosity board. Defconfigs for sam9x60ek adapted in the same
way, but without testing. These should be all sam9x60 boards affected
in U-Boot here.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The board has two SD card slots and we have two defconfigs for booting
from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig'
or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'.
For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity,
sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS,
BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case
for sam9x60_curiosity.
Here the 'mmc1' config has more options enabled to support the raw NAND
flash populated on the board, so the 'mmc' config (for mmc0) was adapted
by enabling additional options, instead of removing options from mmc1.
The 'mem=128M' argument can be dropped from kernel command line, because
it is redundant to memory node in dts in both Linux and U-Boot:
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Similar to MT7981 and MT7986 also MT7988 can have a high number of
reserved-memory regions used by the various hardware offloading
subsystems.
Raise CONFIG_LMB_MAX_REGIONS to 64 to avoid errors when trying to boot
Linux with more then 6 reserved regions:
ERROR: reserving fdt memory region failed (addr=4f700000 size=240000 flags=4)
ERROR: reserving fdt memory region failed (addr=15194000 size=1000 flags=4)
ERROR: reserving fdt memory region failed (addr=15294000 size=1000 flags=4)
ERROR: reserving fdt memory region failed (addr=15394000 size=1000 flags=4)
ERROR: Failed to allocate 0xb161 bytes below 0x80000000.
device tree - allocation error
Fixes: bc4adc97cf ("board: mediatek: add MT7988 reference boards")
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This should have already been enabled but was missed when converting the
base platform defconfig, fix this here.
Fixes: 3c5aa6cacc ("configs: Enable CONFIG_BLK in am57xx_evm and am57xx_hs_evm")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ChromiumOS bootmeth has no tests at present. Before adding more
features. add a basic test.
This creates a disk which can be scanned by the bootmeth, so make sure
things work. It is quite rudimentary, since the kernel is faked, the root
disk is missing and there is no cmdline stored.
Enable the bootmeth for snow so it can build the unit test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 02be57caf7 ("riscv: qemu: Enable usb keyboard as an input
device") adds PCI xHCI support to QEMU RISC-V virtual machines and
enables using a USB keyboard as one of the input devices. Similarly,
enable those for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
PCI register multi-entry support. This fixes ut_dm_dm_test_pci_bus_to_phys
test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
CCF and Sandbox CCF drivers. This fixes ut_dm_dm_test_clk_ccf test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
12x22 font support. This fixes ut_dm_dm_test_video_text_12x22 test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
16bpp and 24bpp video support. This fixes ut_dm_dm_test_video_bmp16
and ut_dm_dm_test_video_bmp24 tests .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
PINCTRL single driver. This fixes ut_dm_dm_test_pinctrl_single test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
BUTTON ADC driver. This fixes ut_dm_dm_test_button_keys_adc test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
MC34708 PMIC driver. This fixes ut_dm_dm_test_power_pmic_mc34708_get test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Increase the
console record size. This fixes ut_bootstd_bootflow_cmd_scan_e .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
SPI NOT bootdev. This fixes ut_bootstd_bootdev_test_cmd_hunt test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename defconfig to include SoC name, use similar pattern as other
RK356x boards: <soc>-<name>.dts -> <name>-<soc>_defconfig
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on STMicroelectronics boards.
With CONFIG_SYS_VENDOR = "st", the logo st.bmp is selected, loaded at the
address indicated by splashimage and centered with "splashpos=m,m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MAIN CPSW0 instance of CPSW Ethernet Switch on TI's J7200 SoC
supports SGMII mode. To enable support for utilizing the SGMII
daughtercard with TI's DP83869 PHY, enable the corresponding config.
Also, since the SGMII daughtercard is connected to the I2C GPIO
Expander 2 connector on the J7200 EVM, powering on the Ethernet PHY and
resetting it requires GPIO Hogging capability. Enable it as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
We need a platform on which we can test our semihosting code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rk3328 rng details to the u-boot.dtsi and
enable the RNG on the Rock64 to be able to provide
a random seed via UEFI.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Fix typo message)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rockchip efuse driver on the Rock64 to
provide a stable ethernet address on the device.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Starfive Visionfive 2, the u-boot environment settings are saved to
on-board SPI flash. Enable relative configs by default and set offset
and size according to upstream linux dts.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add XHCI_PCI to enable usb3-host functions.
Also add usb command and keyboard config.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This build can be used to boot 32-bit standard-distro builds. Enable some
more options, so that all possible EFI UUIDs are decoded, we can search
memory for tables, support the full set of standard-boot features, have
full logging along with debug UART and can boot from CDROM media.
This mirrors a similar patch for qemu-x86_64
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Drop the unknown option from defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Unfortunately the bochs driver does not currently work with distros.
It causes a hang between grub menu selection and the OS displaying
something.
Preliminary investigation shows that GRUB does not jump to the kernel
at all.
This reproduces reliably.
This reverts commit b8956425d5.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # qemu-x86_64
[Slightly modify the commit message about preliminary investigation]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
turn on EFI MM communication
On Corstone-1000 platform MM communication between u-boot
and the secure world (Optee) is done using the FF-A bus.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the previous updates to the device tree, Ten64
can use Standard Boot 'out of the box'.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The watchdog driver was previously enabled but not used
until U-Boot's fsl-ls1088a.dtsi was updated to describe them.
Some Linux distributions (e.g Debian 11) do not engage the
SP805 watchdogs, causing unexpected resets after boot.
To conserve the user experience, turn off the autostart,
and we will provide a mechanism to turn them on at boot
via env vars.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This restores NVMe functionality after PCI(e) NVMe support
was split out from the NVMe driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch adds general board files based on MT7988 SoCs.
MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:
1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The Unmatched board is typically booted from NVMe which requires PCI.
When dropping to a console PCI is not initialized yet. 'pci enum' has to be
called.
Change the configuration to call pci_init() in board_init_r().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Enable USB 3.0 in all RK3328 boards.
=> usb start
starting USB...
Bus usb@ff5c0000: ehci_generic usb@ff5c0000: Failed to get clocks (ret=-19)
Port not available.
Bus usb@ff5d0000: USB OHCI 1.0
Bus usb@ff600000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@ff580000: 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
1 Hub (480 Mb/s, 0mA)
U-Boot Root Hub
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Driver support for rk3328 is not supported so drop this
unused XHCI_DWC3.
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).
Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.
Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.
Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change RK3568 devices to use the newer dwc3-generic driver instead of
the old xhci-dwc3 driver for USB 3.0 support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sound support for chromebook_jerry needs the MAX98090 codec driver. This
was enabled in commit 2d0c01b8f0 ("sound: rockchip: Add sound support
for jerry"), but apparently lost in commit 7ae2729401 ("configs:
Resync with savedefconfig"). Enable it again.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 815ed79d83 ("video: rockchip: Use TrueType fonts with jerry")
enables makes chromebook_jerry use TrueType fonts. Make other veyron
boards switch to it as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit eba768c545 ("rockchip: jerry: Add serial support") enables
ROCKCHIP_SERIAL for chromebook_jerry to make the serial console work
correctly. Enable it also for other veyron boards.
Also enable logging and disable scrolling multiple lines at once as in
chromebook_jerry, and enable silent console as chromebook_minnie does.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 70e351bdfe ("rockchip: jerry: Enable RESET driver") enables
DM_RESET for chromebook_jerry to fix its display as required by changes
to the Rockchip video drivers. Enable it for other veyron boards as
well.
Fixes: cd529f7ad6 ("rockchip: video: edp: Add missing reset support")
Fixes: 9749d2ea29 ("rockchip: video: vop: Add reset support")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DEBUG_UART_SKIP_INIT feature is implemented only by s5p (DEBUG_UART_S5P)
and pl01x (DEBUG_UART_PL010 or DEBUG_UART_PL011) serial drivers, but all
ARCH_ROCKCHIP configs rely on default DEBUG_UART_NS16550. The ns16550
serial driver does not depends on DEBUG_UART_SKIP_INIT, so drop it from
rockchip configs.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Call to board_debug_uart_init() is useless, as mainline U-Boot can
not build TPL for rk3308, and proprietary ddr.bin to be used as TPL
is responsible to init debug uart. Moreover current implementation
of board_debug_uart_init() is not compatible with ROCK Pi S, as it
sets pins for UART2 channel 1 breaking access to sdmmc due to pinmux
conflict. Debug uart for ROCK Pi S is UART0.
Thus, avoid ROCKCHIP_RK3308 to select DEBUG_UART_BOARD_INIT and allow
to deselct it in rock-pi-s-rk3308_defconfig. The DEBUG_UART_BOARD_INIT
is already implied by ARCH_ROCKCHIP, therefore other boards based on
rk3308 chip are not affected by change.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
This is more complex than it needs to be and makes converting these
boards over to plain text env files more difficult. Remove setting
mtdparts as the DTS already contain the partitions. While here also
drop the conflicting definitions from the K2 defconfigs.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This was regressed by the following commit and is required to build with
additional configs enabled.
Fixes: 14439cd71c ("configs: k3: make consistent bootcmd across all k3 socs")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Only accept SPACE to stop autobooting. This is safer to avoid accidental
interruptions on unattended devices.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The common env bits now come via ti_armv7_common.env, include it.
Furthermore restore the board-specific boot targets and their ordering
that is now enforced k3-wide differently. Finally, enable
CONFIG_LEGACY_IMAGE_FORMAT explicitly which got lost while turning
FIT_SIGNATURE on by default for k3 devices.
Fixes: 53873974 ("include: armv7: Enable distroboot across all configs")
Fixes: 4ae1a247 ("env: Make common bootcmd across all k3 devices")
Fixes: 86fab110 ("Kconfig: Enable FIT_SIGNATURE if ARM64")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.
Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some veyron boards seem to have Winbond SPI flash chips instead of
GigaDevice ones. At the very least, coreboot builds for veyron boards
have them enabled [1]. Enable support for them here as well.
[1] https://review.coreboot.org/c/coreboot/+/9719
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
An OP-TEE FIT image will fail to extract in SPL because the malloc stack
size is currently limited to 0x2000 for evb-rk3229 board.
In SPL we do not have to care about size limitations, since we are no
longer bound to SRAM limits after DRAM initialization has been done in TPL.
Use the default value for CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN in order
successfully unpack the FIT image.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_PCI_INIT_R for rock5b pci enumeration during boot in order
to autodetect the PCI ethernet NIC during the boot process.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Puma supports upstream TF-A and is configured to output serial on UART0
instead of the default UART2. Since U-Boot is properly configured to
output on UART0, let's pass the DT to TF-A so there is no need for a
custom TF-A to make the latter output to UART0 too.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long are gone the times TF-A couldn't handle the FDT passed by U-Boot.
Specifically, since commit e7b586987c0a ("rockchip: don't crash if we
get an FDT we can't parse") in TF-A, failure to parse the FDT will use
the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two
years ago.
New boards should likely have this option disabled or explicitly enable
it in their respective defconfig.
Because existing boards might depend on a TF-A version that predates
v2.4, let's just enable this option in all RK3399 defconfigs.
Maintainers of each board can decide for themselves if they would prefer
to disable this option and allow U-Boot to pass the DT to TF-A.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Update the anbernic-rgxx3_defconfig file to support panel autodetection
and automatically updating the compatible string in the devicetree.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable configuration for USB 3.0 controller, the commands required,
and the gadget drivers.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the board.c file for the Odroid Go Advance to support the
Black Edition and the Odroid Go Super. The Odroid Go Advance Black
Edition differs from the original model with the addition of 2
extra buttons and an ESP8266 WiFi module. The Odroid Go Super
adds an additional 2 buttons compared to the Black Edition, along
with a larger panel and larger battery.
This change uses the value of ADC0 to determine which of these
3 models it is, and then changes the ${fdtfile} environment variable
to match the proper devicetree name in mainline Linux.
Tested on an Odroid Go Advance (first revision) and an Odroid Go Super.
The correct ${fdtfile} variable was set for each device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rtl8169 driver, which supports the rtl8125b device, which is
connected on the pciE bus on this board.
Enable also CONFIG_SYS_HAS_NONCACHED_MEMORY to have the descriptors stored.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
turn on EFI MM communication
On corstone1000 platform MM communication between u-boot
and the secure world (Optee) is done using the FF-A bus.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Actually merge the assorted K3 platform improvements that were
supposed to be in commit 247aa5a191 ("Merge branch
'2023-07-21-assorted-TI-platform-updates'")
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmS+Xv0cHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyMgxB/9BTjFfVaglu5+m/kiw
XEVSJSwe1H3sc5vFlMUYTSAOSF/mzdZIZHXC6THkCU1yfzu9AZXhp4mfRUiNTwth
w8bvYXm4ZjSxcGPVxVqfThN8iT/SWLpaUC8j7TosP1VKYwzpGmqLyO+ZLu7IwdH+
/wyXFuYtVQVxmSC6SMNAD5eNtS4O6pufat5e5EkhR2atZ/rhhAYmb9zv3RFuCuSM
bxqM+4/FqpENaIdMOPk7EbB3S1C5MsJS2b+s1oIRRLfItlLjpQG4nZnuJGRlL/Bg
mcqYYgHrAnFbLXVOEe5WxMKR1E2fMbtKSlJGpoYO9rSdQRzxGuyRrDm9M77GH2pJ
0Q/F
=DT1v
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2023.07 cycle:
This small fixes set includes the LTO configs for the boards that had
the SPL size up to the limit (sama5d2-based), such that more code can be
added. It also includes a fix for mmc non-removable.
arm-none-linux-gnueabihf-ld.bfd: u-boot-spl section `__u_boot_list' will not fit in region `.sram'
arm-none-linux-gnueabihf-ld.bfd: region `.sram' overflowed by 100 bytes
SPL is at limit so to stop seeing above error in built, enable
link time optimizations CONFIG_LTO.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Tested-by: Mihai Sain <mihai.sain@microchip.com>
Adding just a tiny bit more code for sama5d2_icp_mmc leads to a SRAM
image overflow. Fix this by enabling LTO for this board, so that such
changes still can be made to the common U-Boot code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Tested-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: restrict patch just to CONFIG_LTO]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Adds a trailing space to SYS_PROMPT to make it easier to distinguish
between commands and the prompt.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Do not limit the maximum size of the buffer that is used to decompress
the OS image in to, this causes issue while inflating the image, if image
size is greater than the buffer.
Remove CONFIG_SYS_BOOTM_LEN
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Default to common bootcmd that is set across all k3 devices.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
This is used when building the FIT image configuration string. Enable
it for all FIT using TI platforms.
Signed-off-by: Andrew Davis <afd@ti.com>
[ extend to other k3 boards ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Having saved environments usually causes inconsistencies while in
development workflow. The saved environments conflict with the
default ones that U-boot should be updating during development
but that doesn't happen and the saved environments need to be
reset during bootups to test the changes causing extra debugs.
Remove the saved environments as a default. Environments can always
be re-enabled locally if one does like them or needs them for
some production environment. Optionally, Uenv.txt can also be used on
some of the boot media.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Allwinner H616 SoC supports several types of DRAM memory. To further
integrate other types of memory, we need to add this delimitation.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that the PHY driver supports the H616 USB PHY, we can enable USB
support for the two H616 boards.
As the OrangePi Zero2 has a USB-C port hard-wired to peripheral mode,
let's enable USB gadget mode for port 0, so people can use fastboot,
ethernet or mass storage functionality.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Adds a test suite to ensure that part_get_info_by_type works correctly
by creating a hybrid GPT/MBR partition table and reading both.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
[trini: Add this on the other sandbox configs]
Signedd-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is more convenient since it does not require a video BIOS. Enable
it for QEMU.
Also drop use of video in SPL for the 64-bit QEMU, since it not needed
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This build can be used to boot standard distro builds, since these are
mostly 64-bit these days. Enable some more options, so that all possible
EFI UUIDs are decoded, we get a proper printf() in SPL, can search
memory for tables, support the full set of standard-boot features, have
full logging and can boot from CDROM media.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the various options needed for display to work on the qemu-x86_64
board. This includes expanding the available malloc() memory in SPL,
since the PCI bus must be enumerated in order to find the video device.
It also includes enabling a bloblist, so that the video parameters can be
passed. This is placed at address 10000 but is not needed after U-Boot
proper reads the information there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add ms so it is easier to search for tables in memory.
Expand the command-line and print buffers so that we can deal with the
very long ChromeOS command lines. (typically 700 characters).
Enable BOOTSTD_FULL to get the full set of standard-boot options.
Replace the existing manual script with 'bootflow scan', since it can
find and boot the OS.
Finally, expand the malloc() space so we can read large kernels into a
bootflow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop IDE and add NVME since this is more common now.
Add ms so it is easier to search for tables in memory.
Expand the command-line and print buffers so that we can deal with the
very long ChromeOS command lines. (typically 700 characters).
Enable BOOTSTD_FULL to get the full set up standard-boot options.
Finally, expand the malloc() space so we can read large kernels into a
bootflow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is possible to boot x86-based ChromeOS machines by parsing a table and
locating the kernel and command line. Add a bootmeth for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop use of the distro boot script and use standard boot instead.
Moving to a text-based environment would be desirable also, but requires
additional work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We want to enable some of the more interesting bootstd features. Move SPL
up to create some room for the larger U-Boot binary. Also disable
microcode since this is not needed
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While NFS is widely used in data centres, and private
networks it's quite a nuanced usecase for device firmware.
A lot of devices already disable it.
Various network protocols should really be opt in, not opt
out, because they add extra size and are potential attack
vectors from a security PoV. In the NFS case it doesn't
really make sense for a lot of devices like tables, SBCs etc.
It's also something we don't really want for SystemReady-IR
due to security concerns.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
use new memory layout and change uboot load address.
open tpm, tee and more config feature
No need to reserve top memory because the reserved space
is moved to the bottom area of memory.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
