In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Implement basic PSCI provider to let OS turn CPU cores off and on,
power off and restart the system and determine PSCI version. This
is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y
CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y
CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4
CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is the PSCI provider, it is necessary to correctly
program CSU and TZASC registers. Those are poorly documented, so
push in the correct values.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is a PSCI provider, map RAM explicitly as NS,
otherwise secondary cores crash with SError when attempting
to access RAM mapped as secure in EL2.
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM pointers are in fact populated by the ATF BL31 blob, in case
U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence
ignore the ROM pointers.
Signed-off-by: Marek Vasut <marex@denx.de>
The custom lowlevel_init implementation is no longer necessary, since
it is responsible for routing and trapping SErrors in U-Boot in EL2,
which is implemented in common code since commit:
6c7691edd5 ("armv8: Always unmask SErrors")
Signed-off-by: Marek Vasut <marex@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When an I2C clock is enabled inside enable_i2c_clk() the clock rate is
configured as PLL_SYS_MAIN_120M_CLK / 2 = 60MHz.
Currently, the I2C clock is retrieved from I2C1_CLK_ROOT, which
may not be the one that was enabled.
As there is no clock driver for the imx7d, it is better to return 60MHz
for the I2C clock.
This provides a workaround for the imx7d-pico board, where I2C4 is
connected to the PMIC.
With this change, it is possible to convert the imx7d-pico board
to DM_I2C and DM_PMIC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 56c2dbdaba ("imx: bootaux: cleanup code") introduces the
following LTO related warning:
"
arch/arm/mach-imx/imx_bootaux.c:24:31: warning: type of ‘hostmap’ does not match original declaration [-Wlto-type-mismatch]
24 | const __weak struct rproc_att hostmap[] = { };
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: array types have different bounds
1590 | const struct rproc_att hostmap[] = {
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: ‘hostmap’ was previously declared here
../aarch64-linux-gnu/bin/ld: warning: u-boot has a LOAD segment with RWX permissions
"
This is because the weak empty array of structures "hostmap" is eventually
replaced by non-empty array of structures with different number of elements.
Fix this by avoiding weak variable size array, instead use a weak function
which returns single pointer to the array.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are no CONFIG_{TOOLS_,SPL_,TPL_,}IMX8M macros, nor is there one for
ARM64. Use plain IS_ENABLED(CONFIG_IMX8M) and IS_ENABLED(CONFIG_ARM64) to
avoid expanding the {TOOLS_,SPL_,TPL_,} part.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
This reinstates change from commit:
e26d0152d6 ("ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables")
which has been dropped in commit:
b0a284a7c9 ("imx: move get_boot_device to common file")
Fixes: b0a284a7c9 ("imx: move get_boot_device to common file")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This converts the following to Kconfig:
CONFIG_DM9000_BYTE_SWAPPED
CONFIG_DM9000_NO_SROM
CONFIG_DM9000_USE_16BIT
CONFIG_DM9000_DEBUG
CONFIG_MXC_GPT_HCLK
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix spurious ampersand in address print e.g.
Find img info 0x&480331a0, size 855
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>"
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
SPL_GPIO_SUPPORT is named SPL_GPIO since commit 83061dbd1c ("Rename
GPIO_SUPPORT to GPIO"), SPL_MMC_SUPPORT is named SPL_MMC since commit
103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"), SPL_SERIAL_SUPPORT is
named SPL_SERIAL since commit 2a73606668 ("serial: Rename
SERIAL_SUPPORT to SERIAL") so let's select the correct Kconfig options.
Fixes: 8b71576f38 ("mx7ulp_com: add support for SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the get chip revision methond to use S400 API, also record
other information like lifecycle and UID to global data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX9 shares same ROM API with i.MX8ULP, so make the i.MX8ULP the function
prototype common and usable by i.MX9.
Also include mmc env functions that use ROM API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add timer_init to update ARM arch timer with correct frequency
from system counter and enable system counter.
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clock API to support CCM root clock and LPCG setting
Set the CCM AUTHEN register to allow non-secure world to set
root clock and lpcg.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN/P/ULP supports ROM API, they have almost same get_boot_device
implementation, so move to a common file. And when support i.MX9,
no need to include the other function copy.
Since sys_proto.h is included in imx_romapi.c, there will be build
warning for i.MX8M because wdog_regs not defined, so include imx-regs.h
in i.MX8M sys_proro.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For SoCs support ROM API, CONFIG_SPL_BOOTROM_SUPPORT is needed,
so use this macro to guard the code to avoid extend the list.
And drop the guard with structure definition, there is no need.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the default mapping of spl_boot_device to weak function of
spl_board_boot_device. So that every board of iMX7/8/8M can overwrite
this function to implement specific mapping.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The SPL SDP is configured as BOOT_DEVICE_BOARD, so when booting from
USB, change its type to BOOT_DEVICE_BOARD, so we can use SDP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With supporting timer_get_boot_us, we can profile boot up time with below
configs and function bootstage_mark_name().
CONFIG_BOOTSTAGE=y
CONFIG_BOOTSTAGE_REPORT=y
CONFIG_CMD_BOOTSTAGE=y
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Simplify the use of the ROM API by using the wrappers that take care
of saving/restoring gd and computing the xor value. This makes the
generated code smaller and the C code easier to read.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The ROM API is thoroughly undocumented, but apparently passing the xor
of the real arguments as an extra argument is required [1]. Also, we
need to do the "save gd/restore gd" dance. These are both error-prone,
and lead to a lot of code duplication.
Since both imx8m[np] and imx8ulp SOCs have this, add a separate
translation unit which is included precisely when the new
CONFIG_IMX8_ROMAPI symbol is set, which provide convenience wrappers
that take care of computing the xor value as well as doing the gd
dance, and that thus have a more intuitive API. Subsequent patches
will make use of these to reduce boilerplate.
[1] One wonders, for example, if the check is only applied to the
lower 32 bits, or if we're implicitly relying on all 64-bit pointer
values we're passing effectively have 0 in the upper 32 bits.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order not to repeat the IMX8MN || IMX8MP || IMX8ULP logic in
multiple places where we need to know if the SOC exposes the ROM API,
add a "def_bool y" Kconfig symbol.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0).
No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is
already handled correctly.
No board is currently affected by this change (rtt_nom != 0 on all i.MX6
ddr3 boards), this will be used by a follow-up change.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixup thermal trips in Linux device tree according to SoC thermal
grade.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Adam Ford <aford173@gmail.com>
Since the power domain driver default select CONFIG_CLK, so we will
meet lots failures without CLK_IMX8MQ, so default select it.
Fixes: commit 4eb82c2e56 ("imx: power-domain: Get rid of SMCCC dependency")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
The badblock should be skipped properly in reading and writing.
Fix the logic. The bcb struct is written, skipping the bad block,
so we need to read using the same logic. This was tested create
bad block in the area and then flash it and read it back.
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
To i.MX8, M core stack is pre-coded in source code, so need to get it
before kicking M core. The stack pointer is stored in the first word of
the first PT_LOAD section __isr_vector. So use a num to index the
section loading.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Fix wrong environment.h and remove DECLARE_GLOBAL_DATA_PTR
Fixes: 30e39ac7c9 (imx: imx7 Support for Manufacturing Protection)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Update the Kconfig and Makefile to allow build for iMX8M and
restrict the build only in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The div loop uses reassign and reuse parent_rate, which causes
the parent rate reference to be wrong after the first loop, the
resulting clock becomes incorrect for div != 1.
Fixes: 829e06bf41 ("imx8ulp: clock: Add MIPI DSI clock and DCNano clock")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.
By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
=> smc 0xc2000003 0 0 0 0 0 0
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable instruction cache early on to speed up the boot process on i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.
The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wait 1ms before issuing the first MRS command to write DDR3 Mode
registers.
There is a requirement to wait a minimum time before issuing command to
the DDR3 device, according to the JEDEC standard this time is 500us
(after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset
CKE Exit time, maximum value 360ns).
It seems that for some reason this is not enforced by the MMDC
controller.
Without this change we experienced random memory initialization failures
with about 2% boot failure rate on specific problematic boards, after
this change we were able to do more than 10.000 power-cycle without a
single failure.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.
In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done. From the i.MX6 RM:
The user should read the results of the associated delay-line at
MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
reasonable delay may be above 1 cycle then the user should indicate it at
MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
MDMISC[WALAT] field. For example, if the result of the write leveling calibration
is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
delay will be 2 and 100/256 parts of a cycle
Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).
Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.
No needs to initialize DDR again after reboot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.
And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i3c controller clock enable/disable function for imx8ulp.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Disable SPL exception vector which causes issue to ROM patch execution
when SPL calling ROM API.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add settings for operating PLL at 933 MHz. This setting is useful in
case the LPDDR4 DRAM should operate at 1866 MHz or 3733 MT/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added crypto node in device tree.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX7D - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX6,i.MX6SX,i.MX6UL - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used in nxp u-boot tree.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The interface for NOR/OneNAND is called "EIM" not "EMI". Fix this.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The previous code wrote the contents of the fuse as is in the
REFTOP_VBGADJ[2:0], but this was wrong if you consider the contents of
the table in the code comment. This table is also different from the
table in the commit description. But then, which of the two is correct?
If it is assumed that an unprogrammed fuse has a value of 0 then for
backward compatibility of the code REFTOP_VBGADJ[2:0] must be set to
6 (b'110). Therefore, the table in the code comment can be considered
correct as well as this patch.
Fixes: 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add PLL 1.4 GHz, 1.5 GHz, 1.6 GHz, 1.8 GHz options for iMX8M SoCs
in case they should be operated faster, e.g. to improve boot time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Linux uses slightly different divider settings for the 1.2 GHz PLL
configuration, adjust the coefficients to match Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.
Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.
Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.
Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Add support of secondary boot address for imx8mn. The secondary
boot address is hardcoded in the fuse. The value is calculated
from there according to the following description:
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
- Secondary boot is disabled if fuse value is bigger than 10, n = fuse
value bigger than 10.
- n == 0: Offset = 4MB
- n == 2: Offset = 1MB
- Others & n <= 10 : Offset = 1MB*2^n
- For FlexSPI boot, the valid values are: 0, 1, 2, 3, 4, 5, 6, and 7.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Similar to what has been done before with c5437e5b for u-boot proper, we
enable the SMP bit for SPL as well. This is necessary when SDP booting
straight into Linux, i.e. falcon boot. When SDP boot mode is active, the
ROM code does not set this bit which makes the caches not work once
activated in Linux.
On an i.MX6ULL (528MHz), this reduces a minimal kernel's boot time into
an initramfs shell from ~6.1s down to ~1.2s.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use imx6_src_get_boot_mode() instead of manually reading SBMR1. The
existing function has proper handling for software overrides of the
bootdevice which can happen, for example, when booting from an alternate
source using `bmode`.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Obatin the SoC current temperature in print_cpuinfo().
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.
And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Get the MAC address from fuse bank5 word 3 and 4. It has
MSB first at lowest address, so have a reverse order with other
iMX used in mac.c
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LPAV is not allocated to APD when dual boot, so LPAV won't
reset when APD is reset. We have to explicitly reset the DDR,
otherwise its initialization will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the freescale vendor name from CPU revision print to align
with other i.MX platforms
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid DCNANO underrun issue on high loading test, set its
read Qos on NIC_LPAV to highest
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the PXP/HIFI4/EPDC to APD domain, otherwise APD not
able to receive interrupts from the modules.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When single boot, assign AP domain as the master domain of the LPAV.
Allocates LPAV master and slave resources like GPU, DCNano, MIPI-DSI
eDMA channel and eDMA request to APD
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S400 enables RDC only when the DBD_EN is fused. Otherwise, the RDC
is allowed by all masters.
Current S400 has issue if the XRDC has released to A35, then A35 reset
will fail in ROM due to S400 fails to get XRDC.
So temp work around is checking the DBD_EN, if it is not fused, we
don't need to call release XRDC or TRDC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct printf format for unsigned long long is %llx and not %llxx.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Force selecting features present in SoC i.MX7ULP.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
CMD_DM is useful for showing the whole DM tree.
Enable it via "imply CMD_DM".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After all these board switch to binman, we could use common imximage.cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Get Unique ID of SoC iMX7ULP, using the logic described in Fusemap
(IMX7ULPRMB2_Rev0_Fusemap) attached in the i.MX 7ULP APRM [1].
[1]
https://www.nxp.com/docs/en/reference-manual/IMX7ULPRMB2.pdf
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
