This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.
To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.
Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.
Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Add a MAC address create based on the OMAP die ID registers.
Then poplulate the ethaddr enviroment variable so that the device
tree alias can be updated prior to boot.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Since SPI register access is so expensive, it is worth transferring data
a word at a time if we can. This complicates the driver unfortunately.
Use the byte-swapping feature to avoid having to convert to/from big
endian in software.
This change increases speed from about 2MB/s to about 4.5MB/s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
We can run the DDR at 400MHz, so update the timings for that purpose.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
For the KVM and XEN hypervisors to be usable, we need to enter the
kernel in HYP mode. Now that we already are in non-secure state,
HYP mode switching is within short reach.
While doing the non-secure switch, we have to enable the HVC
instruction and setup the HYP mode HVBAR (while still secure).
The actual switch is done by dropping back from a HYP mode handler
without actually leaving HYP mode, so we introduce a new handler
routine in our new secure exception vector table.
In the assembly switching routine we save and restore the banked LR
and SP registers around the hypercall to do the actual HYP mode
switch.
The C routine first checks whether we are in HYP mode already and
also whether the virtualization extensions are available. It also
checks whether the HYP mode switch was finally successful.
The bootm command part only calls the new function after the
non-secure switch.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Currently the non-secure switch is only done for the boot processor.
To enable full SMP support, we have to switch all secondary cores
into non-secure state also.
So we add an entry point for secondary CPUs coming out of low-power
state and make sure we put them into WFI again after having switched
to non-secure state.
For this we acknowledge and EOI the wake-up IPI, then go into WFI.
Once being kicked out of it later, we sanity check that the start
address has actually been changed (since another attempt to switch
to non-secure would block the core) and jump to the new address.
The actual CPU kick is done by sending an inter-processor interrupt
via the GIC to all CPU interfaces except the requesting processor.
The secondary cores will then setup their respective GIC CPU
interface.
While this approach is pretty universal across several ARMv7 boards,
we make this function weak in case someone needs to tweak this for
a specific board.
The way of setting the secondary's start address is board specific,
but mostly different only in the actual SMP pen address, so we also
provide a weak default implementation and just depend on the proper
address to be set in the config file.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
The core specific part of the work is done in the assembly routine
in nonsec_virt.S, introduced with the previous patch, but for the full
glory we need to setup the GIC distributor interface once for the
whole system, which is done in C here.
The routine is placed in arch/arm/cpu/armv7 to allow easy access from
other ARMv7 boards.
We check the availability of the security extensions first.
Since we need a safe way to access the GIC, we use the PERIPHBASE
registers on Cortex-A15 and A7 CPUs and do some sanity checks.
Boards not implementing the CBAR can override this value via a
configuration file variable.
Then we actually do the GIC enablement:
a) enable the GIC distributor, both for non-secure and secure state
(GICD_CTLR[1:0] = 11b)
b) allow all interrupts to be handled from non-secure state
(GICD_IGROUPRn = 0xFFFFFFFF)
The core specific GIC setup is then done in the assembly routine.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
armv7.h contains some useful constants, but also C prototypes.
To include it also in assembly files, protect the non-assembly
part appropriately.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
This patch adds the pad to i.MX6DQ and changes the i.MX6DLS
declaration to match the Linux kernel declaration.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Add atmel usba udc driver support, porting from Linux kernel
The original code in Linux Kernel information is as following
commit e01ee9f509a927158f670408b41127d4166db1c7
Author: Jingoo Han <jg1.han@samsung.com>
Date: Tue Jul 30 17:00:51 2013 +0900
usb: gadget: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This patch makes required changes to make use
of I2S0 channel instead of I2S1 channel on exynos5250.
Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
This patch makes the necessary changes for making use of
I2S0 channel instead of I2S1 channel on smdk board. This
changes are done to maintain the uniformity to use I2S0 channel.
Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
To be more EABI compliant and as a preparation for building
with clang, use the platform-specific r9 register for gd
instead of r8.
note: The FIQ is not updated since it is not used in u-boot,
and under discussion for the time being.
The following checkpatch warning is ignored:
WARNING: Use of volatile is usually wrong: see
Documentation/volatile-considered-harmful.txt
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.
Boot tested on OMAP5432 ES2.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
This patch fixes a regression introduced by commit 87d720e0.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
according to the manual frequency of PLL2 PFD2 is 396.000.000
instead of 400.000.000
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Starting with PG2.1 we have a register in the CONTROL_MODULE that is set
with the package type and maximum supported frequency. Add this, and
the relevant mask/values.
Signed-off-by: Tom Rini <trini@ti.com>
We need to allow for a further call-out in spl_board_init. Call this
am33xx_spl_board_init and add a __weak version. This function may be
used to scale the MPU frequency up, depending on board needs.
Signed-off-by: Tom Rini <trini@ti.com>
Because commit 5dc5f36 removed B2 board support,
arch/arm/cpu/s3c44b0/* and arch/arm/include/asm/arch-s3c44b0/*
are not necessary anymore.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Even though the MMU/D-cache is off, some DMA engines still
expect strict address alignment.
For example, the incoming Faraday FTMAC110 & FTGMAC100 ethernet
controllers expect the tx/rx descriptors should always be aligned
to 16-bytes boundary.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
On s5pc1xx mmc devices offset is multiply of 0x100000,
wrong value was 0x10000. Register offset always points
to mmc 0 before this change.
Add macro definition of mmc dev register offset to s5pc1xx and
exynos mmc.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung at samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.
This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.
Finally, this patch cleans up some comments in the start.S file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Consolidating reset code into reset_manager.c. Also
separating reset configuration for virtual target and
real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Some _CLKGATE_MASK and _FRAC_MASK macros were wrong for PFD_480
and the PFD_528 macros were missing.
Fortunately, the incorrect macros weren't being used.
Since both the PFD_480 and PFD_528 registers have the same
structure, and the fields are identical for [0..3] in bytes
[0..3], so a single set of macros will suffice.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add functions to report the HAB (High Assurance Boot) status
of e.g. i.MX6 CPUs.
This is taken from
git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0
cpu/arm_cortexa8/mx6/generic.c
include/asm-arm/arch-mx6/mx6_secure.h
Signed-off-by: Stefano Babic <sbabic@denx.de>
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
OMAP4470 reference design uses TWL6032 PMIC
with a following connection scheme:
VDD_CORE = TWL6032 SMPS2
VDD_MPU = TWL6032 SMPS1
VDD_IVA = TWL6032 SMPS5
Set voltage and frequency values according to
OMAP4470 Data Manual Operating Condition Addendum v0.7
Signed-off-by: Taras Kondratiuk <taras@ti.com>
The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch fix wrong value returned by 's5p_gpio_part_max' function
for Exynos4412.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
the smc cs related registers start at 0x600 and loop with 5 registers
so the reserved register should be in at91_smc structure while no in
at91_cs structure. So fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files: the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.
Insert a GPL-2.0 SPDX-License-Identifier to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.
Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.
Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch have changed mipi dsi write functions' parameters correctly
so that type cast operations were removed. And mipi dsi payload is
composed with array of panel commands to improve readability.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
The first 1MB is not initialized by first stage bootloader.
Check if memory is setup to 16bit mode and ECC is enabled.
If it is, clear the first 1MB.
Also u-boot should report only the half size of memory.
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
the clk_get() function is needed for the da8xx-fb video driver,
which is used on the am3xx based siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Add special function that executes a specially crafted circular
DMA descriptor. The function doesn't wait for the descriptor to
finish the transfer, since the descritor never finishes. This is
useful when operating a SmartLCD through the LCDIF interface, as
the LCDIF does not give us any means to have continuous refresh
of the SmartLCD. Instead, the RUN bit in the LCDIF CTRL register
must be triggered manually. This can be worked around by starting
an DMA transfer which continuously sets the RUN bit. This function
allows starting exactly such transfer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
A little background is probably appropriate for this patch.
Since "the beginning" of usage of the SABRE Lite and Nitrogen6x
boards, DVI detection has been somewhat broken.
Some (most) DVI monitors don't produce the "HPD" bit in
the PHY_STAT0 register, but do show proper toggling of the
RX_SENSE0..3 bits.
Creating a new the bit-mask to include all five bits and
modifying the 'hdmidet' command and internal detection
routines allows these monitors to function properly in U-Boot.
A related patch to our kernels allows things to work under
Linux:
7d8752905c
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
Locking DPLL_GMAC
[mugunthanvnm@ti.com:Configure only if CPSW is selected]
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch performs the following:
1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
TEST: Tested SD-MMC boot on SMDK5250 and Origen.
Tested USB and SPI boot on SMDK5250
Compile tested for SMDKV310.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds APIs to get power reset status and exit the wakeup condition for
both exynos5 and exynos4
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
Fix the wrong mapping between the DDR I/O control registers on AM33XX
SoCs and the software representation in the SPL code.
The most recent public TRM defines the following DDR I/O control registers
offsets:
* ddr_cmd0_ioctrl : offset 0x44E11404
* ddr_cmd1_ioctrl : offset 0x44E11408
* ddr_cmd2_ioctrl : offset 0x44E1140C
* ddr_data0_ioctrl: offset 0x44E11440
* ddr_data1_ioctrl: offset 0x44E11444
While the struct ddr_cmdtctrl has also some reserved bits in the beginning.
The struct is mapped to the address 0x44E11404. As a result "cm0ioctl" points
to the ddr_cmd1_ioctrl register, "cm1ioctl" to the ddr_cmd2_ioctrl and etc.
Registers ddr_cmd0_ioctrl and ddr_data0_ioctrl are never configured because
of this mapping mismatch.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
enum boot_mode is defined twice once in spl.h and also in
spl_boot.c, hence removing the same from spl_boot.c and including
the header file.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For tracing to work it has to be able to access the microsecond timer
without causing a recursive call to the function entry/exit handlers.
Add attributes to the relevant functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch does the folowing
1. change the data types for unsigned int variable to unsigned
2. change the tmu_base type to struct exynos5_tmu_reg *
3. Add timer functionality for get_cur_temp()
4. error handling in the get_tmu_fdt_values()
5. Add check for curr_temp reading
6. some cosmotic changes.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.
Also remove unrelated TPS62361 defines from clocks.h
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
DRA7 EVM board has the below configuration. Adding the
settings for the same here.
2Gb_1_35V_DDR3L part * 2 on EMIF1
2Gb_1_35V_DDR3L part * 4 on EMIF2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
NON SECURE SRAM is 512KB in DRA7xx devices.
So fixing it here.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.
This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.
This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:
* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
performance at the cost of power. Used to operate safely at high
OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
save power. Used to save power at lower OPPs.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Signed-off-by: Tom Rini <trini@ti.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.
Also update the smdk5250 Makefile and config file.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch adds the IOMUX support for Vybrid VF610 platform.
There is a little difference for IOMUXC module between VF610 and i.MX
platform, the muxmode and pad configuration share one 32bit register on
VF610, but they are two independent registers on I.MX platform. A
CONFIG_IOMUX_SHARE_CONFIG_REG was introduced to fit this difference.
Signed-off-by: Alison Wang <b18965@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
