It is not necessary to keep multiple entries for the same setting in DDR
speed tables. Merge them for smaller tables. Also restructure the tables
for smaller size. Cleanup some typedefs.
Enforce strict checking for speed table. If DIMM is running at higher than
known speed, try to use the highest speed setting. If rank is unknown, it
has to panic.
Removed ODT overriding for P2020DS as it is not necessary.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current km_arm boards have a Power-On test jumper. When this
jumper is set, this triggers some Power-On tests on the board.
This patch enables the support of this jumper for starting the
memory_regions test when the jumper is set.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Commit "PPC: Cleanup tqm8xx_pcmcia.c" will clean up the PCMCIA code
to use I/O accessors instead of plain volatile pointer accesses.
This will result in about 300 byte bigger code. Fix custom linker
script to make room for this.
While we are at it, drop unmaintained u-boot.lds.debug linker script.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
nand.c:36: error: static declaration of 'nand_read_buf' follows non-static declaration
/home/marex/u-boot/include/nand.h:139: error: previous declaration of 'nand_read_buf' was here
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The CDS uses PCICLK as SYSCLK. The PCICLK should be 33333333Hz or 66666666Hz.
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPLD 2.2 removed board watch dog support due to the limitation of CPLD
capacity after adding all the requested features, such as switch overriding.
There is no pin-compatible upgrade part available for current PCB design.
So remove codes related to it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to CPLD 2.2, the default configuration is changed, so updated the
description of CPLD command, otherwise it will confusing.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833,
1000, 1066 and 1333 were verified on this board with SO-DIMM
(UG51U6400N8SU-ACF).
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.
SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
* 'post' of git://git.denx.de/u-boot-blackfin:
Blackfin: uart: implement loop callback for post
Blackfin: bf537-stamp/bf548-ezkit: update POST flash block range
Blackfin: post: generalize led/button tests with GPIOs
Blackfin: bf537-stamp: drop uart/flash post tests
Blackfin: post: drop custom test list
Blackfin: bf537-stamp: convert to gpio post hotkey
Let common code set the machine ID.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
As only one RAM bank is used we can rely on the code from arch/arm/lib/board.c
Cc: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Let common code set the machine ID.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Add NAND SPL support to the devkit8000 config
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Without this change CS's configured for synchronous clocking cannot
read data.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for 88E3015 PHY for Marvell GplugD board.
This patch depends on series of patch which adds support for Marvell
GuruPlug-Display.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Update MPC8349EMDS to use unified DDR driver instead of spd_sdram.c.
The unified driver can initialize data using DDR controller. No need to
use DMA if just to initialze for ECC.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2041RDB has almost identical setup for TLB, LAWS, and PCI with
other P-Series CoreNet platforms.
The only difference between P2041RDB & P3041DS/P4080DS/P5020DS is the
CPLD vs PIXIS FPGA which we can handle via some simple #ifdefs in the
TLB and LAW setup tables.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently support 4 SoC/Boards from the P-Series of QorIQ SoCs that
are based on the 'CoreNet' Architecture: P2041RDB, P3041DS, P4080DS, and
P5020DS. There is a significant amount of commonality shared between
these boards that we can refactor into common code:
* Initial LAW setup
* Initial TLB setup
* PCI setup
We start by moving the shared code between P3041DS, P4080DS, and P5020DS
into a common directory to be shared with other P-Series CoreNet boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
RDIMM has different timing parameters from UDIMM. Create new tables for
RDIMMs. Single-, dual- and quad-rank RDIMMs have been verified with speeds
from 800 to 1333MT/s. Speed table expands to include 1600MT/s for future
use. Single- and quad-rank RDIMM entries are copied into UDIMM tables for
future use.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.
The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS &
P5020DS ("Hydra").
The lane_to_slot[] array is initialized dynamically, since board switches
can be used to control the muxing of SERDES lanes to slots.
The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate
slot. The SERDES configuration is queried to help determine the routing
between MACs and slot/phy combination.
If a XAUI card is inserted, muxing for that card is enabled and never
turned off. The PHY address for the 10G XAUI card depends on the slot in
which it's inserted. If it's in slot 1, the address is 4. If it's in
slot 2, the address is 0.
Update the MDIO routing in the P3041DS and P5020DS device trees based on
the board-level muxing. The SERDES configuration determines which
SGMII/XGMII boards are located in which slots, and so the MDIO bus needs
to be muxed correctly whenever talking to a PHY connected to any Fman MAC.
The Fman Ethernet nodes in the device tree also need to be routed to the
correct PHYs.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS.
The board supports add-on cards for SGMII and XAUI functionality. Which
slots on the board these cards are in is a function of the SERDES option
selected and muxes on the board.
Additionally because of the high-configurablity which MDIO bus one is
connected to is "selected" via an FPGA register. We create dummy MDIO
bus for the phy layer and hide the mux manipulation in this dummy layer.
Add fman fdt helper function in board common code it'll be used by several
freescale boards that do various muxing of the MDIO signals based on which
controller/interface one is trying to talk to.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unnecessary or dead code/includes.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
Since commit d388298a59 by
Stefano Babic this file is no longer needed so delete it.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MAC address stored in the inventory eeprom begins at offset 1.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
omap4: fix pad configuration settings for SDP and Panda
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make use of GPIO framework and avoid the following build error:
tx25.c: In function 'tx25_fec_init':
tx25.c:73: error: dereferencing pointer to incomplete type
tx25.c:74: error: dereferencing pointer to incomplete type
tx25.c:75: error: dereferencing pointer to incomplete type
tx25.c:76: error: dereferencing pointer to incomplete type
tx25.c:83: error: dereferencing pointer to incomplete type
tx25.c:84: error: dereferencing pointer to incomplete type
tx25.c:114: error: dereferencing pointer to incomplete type
tx25.c:115: error: dereferencing pointer to incomplete type
tx25.c:116: error: dereferencing pointer to incomplete type
tx25.c:117: error: dereferencing pointer to incomplete type
tx25.c:124: error: dereferencing pointer to incomplete type
tx25.c:125: error: dereferencing pointer to incomplete type
tx25.c:126: error: dereferencing pointer to incomplete type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fix build problem:
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c: In function 'board_init_f':
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:132: warning: implicit declaration of function 'nand_boot'
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:133: warning: 'noreturn' function does return
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
While we are at it, sort include list in netdev.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:
cm41xx.c: In function ‘env_flash_cmdline’:
cm41xx.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:
cm4008.c: In function ‘env_flash_cmdline’:
cm4008.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc8610hpcd: set pci1_hose.config_table after fsl_setup_hose
powerpc/mpc8548cds: set pci1_hose.config_table after fsl_setup_hose
powerpc/mpc8568mds: set pci1_hose.config_table after fsl_setup_hose
Use _bss_start_ofs as the size of the boot loader code+data that we want
to protect in the flash. This replaces use of the no longer defined
_armboot_start.
Fixes:
flash.c: In function ‘flash_init’:
flash.c:75: error: ‘_bss_start’ undeclared (first use in this function)
flash.c:75: error: (Each undeclared identifier is reported only once
flash.c:75: error: for each function it appears in.)
flash.c:75: error: ‘_armboot_start’ undeclared (first use in this function)
Signed-off-by: <greg.ungerer@opengear.com>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The out-of-tree build fails because the Makefiles in question depend on
source files of another directory but do not explicitly mkdir that
directory.
As a matter of fact, other Makefiles under board/*/ directory that refer
to source files under another directory explicitly call mkdir.
This patch adds explicit mkdir's to the Makefiles in question, and
verifies that out-of-tree build is working.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
The ALPR custom FPGA code was missed by commit e6a857d "fpga:
constify to fix build warning" resulting in such warnings:
fpga.c:226: warning: initialization from incompatible pointer type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Commit 58c583b "net: Check network device driver name" increased the
code size and broke building for the ETX094 board.
Adjust the linker script to make it build again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 09c2e90 "unify version_string" defines a default value for
CONFIG_IDENT_STRING in version.h, so any private settings musty be
done before including this file. Move the include for version.h after
the one for common.h to fix the build problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Introduce the --gc-sections for ColdFire platform and clean up the
corresponding lds file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch errors
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixed USR0/USR1 to be LED 0/1 respectively
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on patches from Syed Mohammed Khasim (khasim@ti.com).
Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.
Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes display problems in linux
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.
Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Updated mx53 ddr3 script in order to align with the latest Freescale version from July 8, 2011:
-change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz)
-change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from
"0x092080b0". This changes write recovery from 8 clocks to 6 clocks
(in line with ESDCFG1[tWR])
Signed-off-by: Lily Zhang <r58066@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This is a cosmetic patch, which is changing the gpio_ prefix to
s5p_gpio_.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is driven by need of general gpio_* functions,
which as their parameter are accepting the GPIO pin number, NOT
block and pin.
This makes the code alike to omap, and allows for using more
generic frameworks (e.g. software I2C).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integrator board was apparently never converted over to support
relocation until now. After this the integrator u-boot both compiles
and boots on the Integrator AP.
This also fixes the SDRAM memory size detection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integratorap/cp config for u-boot was outdated and would not
even compile, so fix the obvious missing bits for it to start
building. After this "make ap920t_config/make all" starts working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Innovator and H2 boards used machine_is_* macros for setting the machine
type. These macros are expanded in compile time and thus leaves
unreachable code (though gcc might optimize it).
Switch them to use common code for machine type setting.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
NVIDIA boards and Samsung SMDK6400 already use a local variant of
CONFIG_MACH_TYPE option.
Switch to use the new common code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
The meesc board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Matthias Fuchs <Matthias.Fuchs@esd.eu>
Commit 7616e78 "Add Ethernet hardware MAC address framework to usbnet"
increased the code size and broke building for the ETX094 board.
Adjust the linker script to make it build again.
While we are at it, remove unused u-boot.lds.debug
Signed-off-by: Wolfgang Denk <wd@denx.de>
The sh7757lcr has a local u-boot.lds because the sh7757lcr is only
supported the SPI booting.
This patch refers from the commit "sh: Add KEEP order to start.o section"
(commit ID: b52da2aed8).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).
This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
On newer rev5 hardware the extension board EEPROM I2C address
has been changed to 0x54. Make this I2C address configurable
depending on CONFIG_DIGSY_REV5 so that extention board presence
detection works correctly on newer hardware.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-arm:
drivers/rtc: add Marvell Integrated RTC
Armada100: Add Board Support for Marvell GuruPlug-Display
Armada100: MFP macro naming correction
arm: auto gen asm-offsets.h for mb86r0x
spear: fix build errors for spear3xx/spear600 platforms
cosmetic: arm: lib/board.c: Coding Style cleanup
ARM: versatile: fix board support
SMDKV310: Enable device tree support
SMDKV310: MMC_SPL: Fix building when using "make O="
arm: a320: enable tagged list support
arm: a320: fix multiline comment style
ARMv7: u8500_href: Add missing header to fix compiler warning
Removed unused define, CONFIG_ARMV7.
avr32: add grasshopper (ICnova AP7000) board
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
MAKEALL: remove AT91 boards that are in boards.cfg
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
AT91: Board fix for AT91SAM9261-EK
AT91: SoC fix at91sam9261_matrix.h
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
AT91: change common at91sam9261 files to compile with new scheme
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
README: fix arm920t/at91 path
net/eth.c: drop obsolete at91rm9200 support
README.at91-soc: remove AT91(RM9200) joining notice
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
MAKEALL: remove obsolete at91rm9200 soc
ARM: remove obsolete at91rm9200
omap4: clock init support for omap4460
omap4: support TPS programming
omap: reuse omap3 gpio support in omap4
omap4: sdram init changes for omap4460
omap4: add omap4460 revision detection
mkimage: Add OMAP boot image support
omap: add MMC and FAT support to SPL
omap: add basic SPL support
armv7: start.S: fixes and enhancements for SPL
omap4: automatic sdram detection
omap4: calculate EMIF register values
omap4: add sdram init support
omap4: add clock support
omap4: add OMAP4430 revision check
omap4: cleanup pin mux data
omap4: utility function to identify the context of hw init
DA8xx: fix LPSC constants
DA8xx: switch an enum to defines for consistency
DA8xx: add MMC/SD controller addresses
DaVinci EMAC: declare function for all DA8xx CPUs
DA8xx: add generic GPIO driver
DaVinci: rename gpio_defs.h to gpio.h
omap3evm: eth: Include functions only when necessary
omap3evm: Update ethernet reset sequence for Rev.G board
omap3evm: eth: split function setup_net_chip
omap3: Include array definition only when it is used
omap730p2: fix build breaks
omap2420h4: fix build breaks
omap1610inn: fix build breaks
omap1510inn: fix build breaks
omap5912osk: fix build breaks
omap1610h2: fix build breaks
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
This patch adds basic board support with DRAM and UART functionality
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.
Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Alessandro Rubini <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>
Fix the compiler warning
u8500_href.c: In function 'hrefplus_mmc_power_init':
u8500_href.c:258: warning: implicit declaration of function 'prcmu_i2c_read'
u8500_href.c:265: warning: implicit declaration of function 'prcmu_i2c_write'
by adding the missing header file.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit
GmbH.
See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html
for detailed information about this device.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Fix board part of AT91SAM9261-EK according to the new scheme
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
These functions are not required when CONFIG_CMD_NET
is not defined:
- setup_net_chip()
- reset_net_chip()
- board_eth_init()
This patch wraps them in #ifdef CONFIG_CMD_NET...#endif
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.
The patch uses generic gpio API instead of direct access
to corresponding registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.
The patch moves the reset actions to new function reset_net_chip().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: jtag-console: fix timer usage
Blackfin: switch to common display_options()
Blackfin: serial: move early debug strings into .rodata section
Blackfin: adi boards: also set stderr to nc with helper
Blackfin: update anomaly lists to latest public info
Blackfin: serial: convert to bfin_{read,write} helpers
Blackfin: split out async setup
Blackfin: adi boards: enable pretty flash progress output
Blackfin: drop unused dma.h header from start code
Blackfin: portmux: allow header to be included in assembly files
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
Blackfin: sync MMR read/write helpers with Linux
Blackfin: gpio: optimize free path a little
Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
Blackfin: uart: fix printf warning
Blackfin: add init.elf helper code
Blackfin: dont reset SWRST on newer bf526 parts
Blackfin: adi boards: enable multi serial support by default
Blackfin: uart: add multiple serial support
Blackfin: uart: move debug buffers into local bss
Fix:
tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix compiler warning:
cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type
Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We also have to shift TEXT_BASE to accomodate for the additional
code size.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.
Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Doesn't make sense to provide this function to boards which defined
CONFIG_ENV_IS_NOWHERE. Such a board gets a linking error because
common/env_nowhere.c doesn't define saveenv().
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Enable printout of i2c deblocking status if chips were in block
state or deblocking failed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Be verbose if do_setboardid was called and print
correct names of variables in do_checkboardidhwk.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Common code should be valid for more than one architecture,
therefore the km82xx specific code was removed from common.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
This code is unused and therefore dead code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The file common.c grows in the past. So move the IVM specific
code into an ivm.c file.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
This is unneeded here because we save the environment when
the board boots the first time. At this time we have set
the values already.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The ethaddr is stored inside the inventory eeprom. During
boottime this value was read out and the ethaddr variable was
set. Previously this was only done if it ethaddr == NULL but
this is wrong for our ARM boards. Because ethaddr is at this
stage never NULL for ARM due to the random calculation of a
MAC address in mvgbe.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
These defines and the header keymile_hdlc_enet.h are obsolete
due to the removed hdlc code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the default environment:
run develop: this configures the environment to setup the
rootfs via nfs
run ramfs: this configures the environment to setup the
rootfs in ram
Each architecture now has a "arch" variable which is used
to load the architecture specific debug scripts and to set
the rootpath for NFS.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Up to now only reading 'appreg' value was implemented in the
digsyMTC special 'mtc appreg' command. Extend the command to
support writing appreg value, too.
Signed-off-by: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Add detection and initialisation for graphic extension board
and support splash screen when booting. Enable "bmp" command
in the board configuration and provide "disp" command to
be able to switch the display on/off.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
There is no need to use set_timer(). Replace with appropriate use of
get_timer()
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
We need a TLB entry to call get_ram_size(); the common code doesn't create
one until *after* fixed_sdram() has determined the size. So we set up tlbs
for the max possible size and tear them down once we're done with
get_ram_size(); the common 85xx code will then set up a final set of tlb
entries for the *actual* detected size of ddr.
This prevents us from having TLB entries that are larger than DDR sitting
around for very long, which is not a recommended scenario.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-mmc:
mmc: rescan fails on empty slot
AT91:mmc:fix multiple read/write error
mmc: Access mode validation for eMMC cards > 2 GiB
mmc: sh_mmcif: add support for Renesas MMCIF
mmc: fix the condition for MMC version 4
MMC: add marvell sdhci driver
MMC: add sdhci generic framework
MMC: add erase function to both mmc and sd
MMC: unify mmc read and write operation
mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony
mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
This patch fixes compiler errors due to missing definitions of
CONFIG_SYS_SDRAM_BASE and CONFIG_SYS_INIT_SP_ADDR.
It also does some cleanup: CONFIG_SYS_TEXT_BASE was moved to scb9328.h,
obsolete config.mk was removed. The scb9328 board has 1 DRAM bank, so don't
ask for more banks. CONFIG_NR_DRAM_BANKS will ever be 1.
Signed-off-by: Torsten Koschorrek <koschorrek@synertronixx.de>
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
mx27_uart_init_pins does the IOMUX setting for UART1 port.
Change the function name to make the UART port number explicit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
These boards can have an addon card plugged onto them, so enable
support for it.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If DDR initialziation uses a speed table and the speed is not matched,
print a warning message instead of silently ignoring.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow overriding RCW for all RDIMM, not only quad-rank ones.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LAW & TLB code to handle the case in which
CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch add support for the Network Space v2 board and parents, based
on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2
and Internet Space v2.
Additional information is available at:
http://lacie-nas.org/doku.php?id=network_space_v2
Signed-off-by: Simon Guinot <sguinot@lacie.com>
This adds support for the keymile Kirkwood BEC portl2 board. This board
relies on the km_arm (km_kirkwood) BEC.
The egiga driver is configured for a 100M full-duplex, A/N off connnection
to the backplane. This board has always ethernet present, because it is
connected to the marvell switch similar to mgcoge3un. The reset_phy
functionality is also the same to mgcoge3un.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
The phy is also configured with "RGMII clock transitions when data
stable" and "Class A driver for the direct backplane connection".
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
This patch removes the board implemenatation for flash driver which can now
safely switched to the common cfi driver.
Compile tested for all atstk100x boards, runtime tested on atstk1002.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
