Since ADS860.h includes "board/fads/fads.h" with ramifications
on the CONFIG_COMMAND treatment, it too has to be adjusted to
exclude already configured commands in this same commit.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
- Add optional ECC generation routine to preserve existing
RAM values. This is needed for the Linux log-buffer support
- Add optional DDR2 setup with CL=4
- GPIO50 not used anymore
- Lime register setup added
Signed-off-by: Stefan Roese <sr@denx.de>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAM
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the "normal" Bamboo NOR booting port, so
that it is compatible with the coming soon NAND booting
Bamboo port.
It also enables the 2nd NAND flash on the Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
The OBJTREE != SRCTREE build scenario was broken.
This fixes it.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.
Signed-off-by: Stefan Roese <sr@denx.de>
* Cleaned up the CDS PCI Config Tables and added NULL entries to
the end
* Fixed PCIe LAWBAR assignemt to use the cpu-relative address
* Fixed 85xx PCI code to assign powar region sizes based on the
config values (rather than hard-coding them)
* Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
Signed-off-by: Andy Fleming <afleming@freescale.com>
This included some changes to common files:
* Add 8568 processor SVR to various places
* Add support for setting the qe bus-frequency value in the dts
* Add the 8568MDS target to the Makefile
Signed-off-by: Andy Fleming <afleming@freescale.com>
Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
on some ITX boards, notably those with a revision 3.1 CPU.
Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Michael Benedict <MBenedict@twacs.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
