This reverts commit ca9c8a1e10,
which causes compile warnings ("large integer implicitly truncated
to unsigned type") on all systems that use this driver. The warning
results from passing long constants (TX_CFG, RX_CFG) into
smc911x_set_mac_csr() which is declared to accept "unsigned
character" arguments only.
Being close to a release, with nobody available to actually test the
code or the suggested fixes, it seems better to revert the patch.
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Use existing struct fec512x instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
This patch fixes MDIO clock setup in case when OPB frequency is 100MHz.
Current code assumes that the value of sysinfo.freqOPB is 100000000
when OPB frequency is 100MHz. In reality it is 100000001. As a result
MDIO clock is set to incorrect value, larger than 2.5MHz, thus violating
the standard. This in not a problem on boards equipped with Marvell PHYs
(e.g. Canyonlands), since those PHYs support MDIO clocks up to 8.3MHz,
but can be a problem for other PHYs (e.g. Realtek ones).
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
When PCI device use system memory, some PCI host controller should be
set physical memory address.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
eth_halt() function in the smc911x drivers used to call the
smc911x_reset() function. eth_halt() used to be called after
tftp transfers. This used to put the ethernet chip in reset
while the linux boots up resulting in the ethernet driver
not coming up. NFS boot used to fail as a result.
This patch calls smc911x_shutdown() instead of smc911x_reset().
Some comments received has also been fixed.
Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some boards do not have SROM support for the DM9000 network adapter.
Instead of listing these board names in the driver code, make this
option configurable from the board config file.
It also removes a build warning for the at91sam9261ek board:
'dm9000x.c:545: warning: 'read_srom_word' defined but not used'
And it repaires the trizepsiv board build which was broken around the
same routines
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
If the MAX address is given by the environment, write it back to the
hardware.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Make the U-Boot dm9000 driver read addresses from EEPROM just
like Linux does ... read six bytes, instead of reading twelve
bytes and then discarding every other one.
Using the right Ethernet address is a big win.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Fix the problem that cannot access actual data when CPU data cache enabled.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
cs8900.c: In function 'eth_init':
cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type
cs8900.c:165: error: invalid operands to binary <<
cs8900.c:166: error: invalid operands to binary <<
cs8900.c:167: error: invalid operands to binary <<
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Also, do not bother checking the EEPROM if the env is setup. This
simplifies the code greatly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Dnek <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Erik Stahlman <erik@vt.edu>
CC: Daris A Nevil <dnevil@snmc.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The sh_eth driver can also be simplified a bit by using enetaddr member of
the eth_device structure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Carlos Munoz <carlos@kenati.com>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The cs8900 driver also changes slightly in that the hardware is not
consulted if the mac address in the env is sane.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Marius Groeger <mgroeger@sysgo.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Since the address is in the PLM_DEVICE_BLOCK structure already, there is
no need to pass the NodeAddress as a second parameter. So drop the second
argument to the LM_SetMacAddress() function (and update the tigon3 driver
accordingly).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The drivers that get converted here:
3c589
4xx_enet
dc2114x
dm9000x
enc28j60
fsl_mcdmafec
ks8695eth
mcffec
rtl8019
rtl8169
s3c4510b_eth
xilinx_emac
xilinx_emaclite
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Stefan Roese <sr@denx.de>
CC: Sascha Hauer <saschahauer@web.de>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
CC: Greg Ungerer <greg.ungerer@opengear.com>
CC: Xue Ligong <lgxue@hotmail.com>
CC: Masami Komiya <mkomiya@sonare.it>
CC: Curt Brune <curt@cucy.com>
CC: Michal SIMEK <monstr@monstr.eu>
Since the on-chip MAC does not have an eeprom or similar interface, force
all Blackfin boards that use this driver to setup the board data with a
proper MAC.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
sh_eth_reset is function to reset Ether IP.
The MAC address is stored in IP, but it is initialized by this function.
OS (e.g. Linux Kernel) can not use this device when initialized.
This revises this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Commit af1c2b84 added a generic phy support, with an ID of zero
and a 32 bit mask; meaning that it will match on any PHY ID.
The problem is that there is a test that checked if a matching
PHY was found, and if not, it printed the non-matching ID.
But since there will always be a match (on the generic PHY,
worst case), this test will never trip.
In the case of a misconfigured PHY address, or of a PHY that
isn't explicitly supported outside of the generic support,
you will never see the ID of 0xffffffff, or the ID of the
real (but unsupported) chip. It will silently fall through
onto the generic support.
This change makes that test useful again, and ensures that
the selection of generic PHY support doesn't happen without
some sort of notice. It also makes it explicitly clear that
the generic PHY must be last in the PHY table.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The smc911x driver has a lot of useful defines/functions which can be used
by pieces of code (such as example eeprom programmers). Rather than
forcing each place to duplicate these defines/functions, split them out
of the smdc911x driver into a local header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Guennadi Liakhovetski <lg@denx.de>
CC: Magnus Lilja <lilja.magnus@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
Added the struct containing PHY settings for the Vitesse VSC8211 phy to
the phy_info list in tsec.c
Signed-off-by: Pieter Henning <phenning@vastech.co.za>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added new CONFIG options for the three type of MAC-PHY interconnect and
applied them all relevant board config files
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SOFT_RESET must be asserted for at least 3 TX clocks. Usually, that's about 30
clock cycles, so it's been mostly working. But we had no guarantee, and at
slower bitrates, it's just over a microsecond (over 1000 clock cycles). This
enforces a 2 microsecond gap between assertion and deassertion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
100Mbs ethernet does not work on sh7763 chips due to the wrong value being
used in the GECMR register. Following diff fixes the problem
Signed-off-by: Simon Munton <simon@nidoran.m5data.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Driver for Dave DNET ethernet controller (used on Dave/DENX
QongEVB-LITE board).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Modified mii_init to support boards with PHYs that are not set to
autonegotiate, but still want to use u-boot's mii commands to probe
the smi bus. Such PHYs will not set the Autonegotiate-done bit.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Redo how pointers are managed to get rid of ugly casts and strict pointer
aliasing issues that are highlighted by gcc 4.3.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
No point in having a Blackfin-specific define "CONFIG_BFIN_MAC_RMII" that
does exactly the same thing as common "CONFIG_RMII".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather then defining our own DEBUGF(), just use the common debug().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than having the on-chip MAC hardcoded to phy address 1 and a speed
of 2.5mhz, use these as defaults if the board doesn't specify otherwise.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Cleanup and rewrite the MII/PHY related functions so that we can reuse the
existing common linux/miiphy.h code and hook into the `mii` command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Rather than hardcoding MDCDIV to 24 (which is correct for ~125mhz SCLK),
use the real algorithm so it gets set correctly regardless of SCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.
This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adjusts the LED control so that interrupt lines are not reading LEDs
and effectively causing indefinite interrupts to the controller.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch changes the reg_read/_write to smc911x_reg_read/_write
and defines then as weak so that they can be overridden by board
specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch tries to ensure that phy interrupt pin
won't be asserted after booting. We experienced
following issues with current 88E1121R phy init:
Marvell 88E1121R phy can be hardware-configured
to share MDC/MDIO and interrupt pins for both ports
P0 and P1 (e.g. as configured on socrates board).
Port 0 interrupt pin will be shared by both ports
in such configuration. After booting Linux and
configuring eth0 interface, port 0 phy interrupts
are enabled. After rebooting without proper eth0
interface shutdown port 0 phy interrupts remain
enabled so any change on port 0 (link status, etc.)
cause assertion of the interrupt. Now booting Linux
and configuring eth1 interface will cause permanent
phy interrupt storm as the registered phy 1 interrupt
handler doesn't acknowledge phy 0 interrupts. This
of course should be fixed in Linux driver too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All CF platforms' mii.c are consolidated into one
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Patch to fix buffer allocation size and alignment. Buffer needs to be u32 aligned and
PKTSIZE_ALIGN bytes long.
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Currently VSC8601 doesn't link with 10/100M partners if the
EEPROM/Strapping is not set up.
Setting the auto-neg register fixes this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
get_prom function was used __attriute__ , but it is not enable.
ax88796.o does not do link besides ne2000.o. When ld is carried
out, get_prom function of ax88796.c is ignored.
This problem is a thing by specifications of ld.
I checked and test this patch on SuperH and MIPS.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fix TBI PHY accesses to use the proper offset in CPU register space. The
previous code would incorrectly access the TBI PHY by reading/writing to CPU
register space at the same location as would be used to access external PHYs.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The RSK7203 board has the SMSC9118 wired up 'incorrectly'.
Byte-swapping is necessary, and so poor performance is inevitable.
This problem cannot evade by the swap function of CHIP, this can
evade by software Byte-swapping.
And this has problem by FIFO access only. pkt_data_pull/pkt_data_push
functions necessary to solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Adds support for configuring the TBI to talk properly with the SerDes.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is to prepare the way for board code passing in the tsec_info structure
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
dm9000 has code to detect and initialize external phy parts, but later
on in the code the part is forced to use the internal phy
unconditionally. Remove the unused/untested code.
change the GPIO initialization so that only the GPIO used as an
internal phy reset (hardwired in the chip) is set as an output. The
remaining GPIO need to be handled by board specific code to prevent
possible drive conflicts. Set as inputs for safety.
replace a few magic numbers with defines
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add FEC Buffer descriptors and data buffer in SRAM for
faster execution and access.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The only board using this driver is the SL8245 board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added board_eth_init() function to bf537-stamp board.
Removed initialization for the Blackin EMAC driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes a problem that RTL8110SCL started transfer
with an incorrect memory address.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The received status and len was in little endian
format and caused the ethernet unable to proceed
further. Add __le16_to_cpu() in dm9000_rx_status_8/16/32bit().
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This PCI-X e1000 variant works by just adding in the correct
PCI IDs in the appropriate places.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Remove duplicate definitions in include/lxt971a.h.
Remove duplicate registers and bits definitions in
include/lxt971a.h for standard MII registers, and
use values in include/miiphy.h instead.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Renesas SH7763 has 2 channel Ethernet device.
This is 10/100/1000 Base support.
But this patch check 10/100 Base only.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
If enable DEBUG, can not compile ne2000 driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
According to the Application Notes of the DM9000, only the 2 bits 0:1 of
the status byte need to be checked to identify a valid packet in the fifo
But, The several different Application Notes do not all speak the same
language on these bits. They do not disagree, but only 1 Application Note
noted explicitly that only these 2 bits need to be checked.
Even the datasheets do not mention anything about these 2 bits.
Because the old code, and the kernel check the whole byte, I left this piece
untouched.
However, I tested all board/DM9000[A|E|EP] devices with this 2 bit check, so
it should work.
Notice, that the 2nd iteration through this receive loop (when a 2nd packet is
in the fifo) is much shorter now, compared to the older U-boot driver code,
so that we can maybe run into a hardware condition now that was never seen
before, or maybe was seen very unfrequently.
Additionaly added a cleanup of a stack variable.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
A last minute cleanup before submitting the DM9000A patch series yesterday introduced
a bug in reading the rx-status registers in 32bit mode only.
This patch repairs this.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some lines of the U-boot DM9000x driver are longer than 80 characters, or
need some other minor cleanup.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The DM9000A network controller does not work with the U-boot DM9000x driver.
Analysis showed that many incoming packets are lost.
The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to
check for a valid rx packet be done on the interrupt status register, not
directly by performing the dummy read and the rx status check as is currently
the case in the u-boot driver.
When the recommended poll is done as suggested the driver starts working
correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there
can be more than 1 package in the fifo at the same time.
The driver must perform the rx-status check in a loop and read and handle all
packages until there is no more left _after_ the interrupt RX flag is set.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the
reset procedure must be done twice to properly reset the DM9000 by means of software.
This errata is not needed anymore for the DM9000A, but it does not bother it.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The eth_send routine of the U-boot DM9000x driver does not match the
DM9000 or DM9000A application notes/programming guides.
This change improves the stability of the DM9000A network controller.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
It seems that the debugging code of the DM9000x driver in U-boot has not been
compiled for a long time, because it cannot compile...
Also rearranged some loglines to get more useful info while debugging.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The U-boot DM9000x driver contains a compile time bus-width definition for
the databus connected to the network controller.
This compile check makes the code unclear, inflexible and is unneccessary.
It can be asked to the network controller what its bus-width is by reading bits
6 and 7 of the interrupt status register.
The linux kernel already uses a runtime mechanism to determine this bus-width,
so the implementation below looks somewhat like that implementation.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.
The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Vitesse VSC8601 RGMII PHY has internal delay for both Rx
and Tx clock lines. They are configured using 2 bits in extended
register 0x17.
Therefore CFG_VSC8601_SKEW_TX and CFG_VSC8601_SKEW_RX have
been introduced with valid values 0-3 giving 0.0, 1.4,1.7 and 2.0ns delay.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
--
drivers/net/tsec.c | 6 ++++++
drivers/net/tsec.h | 3 +++
2 files changed, 9 insertions(+), 0 deletions(-)
The ethernet hang is caused by receiving buffer in DRAM is not
yet ready due to access cycles require longer time in DRAM.
Relocate DMA buffer descriptors from DRAM to internal SRAM.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Move non-inlied functions into specific drivers file
Set get_prom as weak
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove a redundant register definition, clean up some coding style
violations.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch makes SPARC/LEON processors able to read and write
to the SMC91111 chip using the chip external I/O bus of the memory
controller. This patchs defines the standard in and out macros
expected by the SMC9111 driver.
To access that I/O bus one must set up the memory controller
(MCTRL or FTMCTRL) correctly. It is assumed that the user sets
up this correctly when the other MCTRL parameters are set up. It
can be set up from the board configuration header file.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds a driver for the following smsc network controllers:
LAN9115
LAN9116
LAN9117
LAN9215
LAN9216
LAN9217
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Add 82541ER device with latest integrated IGP2 PHY.
Introduced CONFIG_E1000_FALLBACK_MAC for NIC bring-up with empty eeprom.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
GRETH is an Ethernet 10/100 or 10/100/1000 MAC with out without
a debug link (EDCL). The GRETH core is documented in GRIP.pdf
available at www.gaisler.com.
If the GRETH has GigaBit support (GBIT, Scatter gather, checksum
offloading etc.) can be determined by a bit in the control register.
The GBIT MAC is supported by operating in GRTEH 10/100 legacy mode.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
RTL8211B sets link state register after autonegotiation complete,
so with bootdelay=0 RTL8211B will report lack of the link.
To fix this, we should wait for aneg to complete, even if the
link is currently down.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards. A small firwmare must be uploaded to its on-board memory
before it can be enabled. This patch adds the code which uploads firmware
(but not the firmware itself).
Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs. The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
AX88796L is device of NE2000 compatible.
This patch support AX88796L ethernet device.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are more devices of the NE2000 base.
A present code is difficult for us to support more devices.
To support more NE2000 clone devices, separated the function.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly. We workaround all the anomalies via this macro.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
rx_status on the memory is basically in LE, but needs to be handled in CPU
endian. le32_to_cpu() takes up this mission. Even if on the sane hardware,
it'll work fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Current driver is meant for cache coherent systems. This patch adds
flush_cache() routines to support cache non-coherent systems.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
"to = (currticks() + RTL_TIMEOUT)" has possibilities to wrap around. If it
does, the condition "(currticks() < to)" becomes invalid and immediately
leads to tx timeout error. This patch introduces the fine-graded udely(10)
loops to ease the impact of wrapping around.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add the support of RealTek RTL8211B PHY, the RTL8211B
PHY only supports RGMII and MII mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current TSEC driver limits MDIO access to the devices that have been configured as attached
to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands.
Signed-off-by: Michael Firth <michael.firth@bt.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Change return values of init() functions in all Ethernet drivers to conform
to the following:
>=0: Success
<0: Failure
All drivers going forward should return 0 on success. Current drivers that
return 1 on success were left as-is to minimize changes.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>
It is unclear on what platforms this driver has been tested, since
noone up to now defines CONFIG_RTL8169 in the board configuration
header. Now it has been fixed for a big-endian mpc8241 based
linkstation platform. This patch presents the necessary endianness
conversion fixes.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Enabled cache in cpu_init_f() for faster flash to mem allocation. Updated cache handling in start.S. Applied cache invalidate in fec_send() and fec_recv(). Added CFG_UNIFY_CACHE for CF V3 only.
Signed-off-by: TsiChung <tcliew@Goku.(none)>
