On Intel Quark, lots of registers on the message port need be
programmed. Add handy clrbits, setbits, clrsetbits macros for
message port access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.
Enable PCIe controller per Quark firmware writer guide.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.
To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement write_acpi_table() to create a minimal working ACPI table.
This includes writing FACS, XSDT, RSDP, FADT, MCFG, MADT, DSDT & SSDT
ACPI table entries.
Use a Kconfig option GENERATE_ACPI_TABLE to tell U-Boot whether we need
actually write the APCI table just like we did for PIRQ routing, MP table
and SFI tables. With ACPI table existence, linux kernel gets control of
power management, thermal management, configuration management and
monitoring in hardware.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tidied up whitespace and aligned some tabs:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have generic routine to calculate relocation address,
remove the x86 specific one which is now only used by coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Increase lib_sysinfo memrange entry number to 32 to sync with coreboot.
This allows a complete E820 table to be reported to the kernel, as on
some platforms (eg: Bayley Bay) having only 16 entires does not cover
all the memory ranges.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have an efi.h header we can use that for FSP error defines.
Drop the FSP ones.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can fail. In this case we should return the error rather than
swallowing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code may be useful for boards that use driver model for PCI.
Note: It would be better to have driver model automatically call this
function somehow. However for now it is probably safer to have it under
board control.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When using different release version of Intel FSP, the VPD_IMAGE_REV
is different (ie: BayTrail Gold 3 is 0x0303 while Gold 4 is 0x0304).
Remove the asserting of this so that U-Boot does not hang in a debug
build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.
Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than add these as open-coded values, create an enum with the commonly
used flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bring in this file from Linux 4.1. It supports relocation features specific
to x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application, U-Boot must request memory from EFI,
and provide access to the boot services U-Boot needs.
Add library code to perform these tasks. This includes efi_main() which is
the entry point from EFI. U-Boot is built as a shared library.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 the global_data pointer is provided through a somewhat-bizarre and
x86-specific mechanism: the F segment register is set to a pointer to the
start of global_data, so that accesses can use this build-in register.
When running as an EFI application we don't want to mess with the Global
Descriptor Table (GDT) and there is little advantage (in terms of code size)
to doing so.
Allow global_data to be a simple variable in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is now handled by generic U-Boot code so we do not need an x86 version.
It is no-longer called, so remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These flags now overlap some global ones. Adjust the x86-specific flags to
avoid this. Since this requires a change to the start.S code, add a way for
tools to find the 32-bit cold reset entry point. Previously this was at a
fixed offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
BayTrail FSP Gold4 release adds one UPD parameter to control IGD
enable/disable.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The PIIX3 chipset does not integrate an I/O APIC, instead it supports
connecting to an external I/O APIC which needs to be enabled manually.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently during writing MP table I/O interrupt assignment entry, we
assume the PIRQ is directly mapped to I/O APIC INTPIN#16-23, which
however is not always the case on some platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We need walk through all functions within a PCI device and assign
their IRQs accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Turn on cache on the pci option rom area to improve the performance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some exceptions cause an error code to be saved on the current stack
after the EIP value. We should extract CS/EIP/EFLAGS from different
position on the stack based on the exception number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
These two declarations in arch/x86/include/asm/interrupt.h conflict
with ones in include/linux/compat.h, so x86 boards cannot include
<linux/compat.h>.
The comment /* arch/x86/lib/interrupts.c */ is bogus now, and we do
not see any definitions of disable_irq() and enable_irq() in there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.
Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
it is not apic related and only used by ivybridge
- Fix coding convention issues
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
cpu_x86_bind()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.
To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
As VGA option rom needs to run at C segment, although QEMU PAM emulation
seems to only guard E/F segments, for correctness, move VGA initialization
after PAM decode C/D/E/F segments.
Also since we already tested QEMU targets to differentiate I440FX and Q35
platforms, change to locate the VGA device via hardcoded b.d.f instead of
dynamic search for its vendor id & device id pair.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
QEMU always decode legacy IDE I/O ports on PIIX chipset. However Linux ata_piix
driver does sanity check to see whether legacy ports decode is turned on.
To make Linux ata_piix driver happy, turn on the decode via IDE_TIMING register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the legacy segments C/D/E/F do not decode to system RAM.
Turn on the decode via Programmable Attribute Map (PAM) registers
so that we can write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
This driver supports multi-core init and sets up the CPU frequencies
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This permits init of additional CPU cores after relocation and when driver
model is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since we do these sorts of operations a lot, it is useful to have a simpler
API, similar to clrsetbits_le32().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most modern x86 CPUs include more than one CPU core. The OS normally requires
that these 'Application Processors' (APs) be brought up by the boot loader.
Add the required support to U-Boot to init additional APs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to return the address of the Interrupt Descriptor Table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we start up additional CPUs we want them to use the same Global
Descriptor Table. Store the address of this in global_data so we can
reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subset of this header file from Linux 4.0 to support atomic operations
in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides a way of passing information to Linux without requiring the
full ACPI horror. Provide a rudimentary implementation sufficient to be
recognised and parsed by Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing code is pretty ancient and is unreliable on modern hardware.
Generally it will hang.
We can use port 0xcf9 to initiate reset on more modern hardware (say in the
last 10 years). Update the reset_cpu() function to do this, and add a new
'full reset' function to perform a full power cycle.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The correct GPIOBASE address on the baytrail is 0x48
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On x86 boards, platform chipset receives up to four different
interrupt signals from PCI devices (INTA/B/C/D), which in turn
will be routed to chipset internal PIRQ lines then routed to
8259 PIC finally if configuring the whole system to work under
the so-called PIC mode (in contrast to symmetric IO mode which
uses IOAPIC).
We add two major APIs to aid this, one for routing PIRQ and the
other one for generating a PIRQ routing table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can write the configuration table in last_stage_init() for all x86
boards, but not with coreboot since coreboot already has them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to assign an IRQ number to PCI device's interrupt
line register in its configuration space, so that the PCI device
can have its interrupt working under PIC mode after OS boots up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For starting a Linux console on the superio serial port under
interrupt mode, the IRQ number must be configured.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The prefix PCH was taken from ivybridge port. However Queensbay
platform official document does not mention PCH. It is composed
of TunnelCreek processor and Topcliff IOH chipset. For accuracy,
avoid using PCH prefix in the macro.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move chromebook_link over to driver model for PCI.
This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)
This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.
In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have done with the generic board conversion for all the boards
of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86.
Let's select SYS_GENERIC_BOARD for those architectures, so we can
tell which architecture has finished the conversion at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move PCI_REG_ADDR and PCI_REG_DATA from arch/x86/lib/pci_type1.c to
arch/x86/include/asm/pci.h, also define PCI_CFG_EN so that these
macros can be used for pci configuration space access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
device.h for integrated pci devices' bdf on Quark SoC and quark.h for
various memory-mapped and i/o-mapped base addresses within SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since the FSP is a black box it helps to have some sort of debugging
available to check its inputs. If the debug UART is in use, set it up
after CAR is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid casts, find_fsp_header() should return a pointer. Add asmlinkage
to two API functions which use that convention. UPD_TERMINATOR is common
so move it into a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This setting will be used by more than just ivybridge so make it common.
Also rename it to PCIE_ECAM_BASE which is a more descriptive name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The memory reference code takes a very long time to 'train' its SDRAM
interface, around half a second. To avoid this delay on every boot we can
store the parameters from the last training sessions to speed up the next.
Add an implementation of this, storing the training data in CMOS RAM and
SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing IP checksum function is only accessible to the 'coreboot' cpu.
Drop it in favour of the new code in the network subsystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
On some x86 processors (like Intel Quark) the MTRR registers are not
supported. This is reflected by the CPUID (EAX 01H) result EDX[12].
Accessing the MTRR registers on such processors will cause #GP so we
must test the support flag before accessing MTRR MSRs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CPUID (EAX 01H) returns MTRR support flag in EDX bit 12. Probe this
flag in x86_cpu_init_f() and save it in global data.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We shouldn't assume that the VGA ROM can always be loaded at c0000. This
is only true on x86 machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These two are not worth having separate inline functions as they are
really simple, so drop them.
Also changed 'type' parameter of fsp_get_next_hob() from u16 to uint.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.
For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Memory Type Range Registers are used to tell the CPU whether memory is
cacheable and if so the cache write mode to use.
Clean up the existing header file to follow style, and remove the unneeded
code.
These can speed up booting so should be supported. Add these to global_data
so they can be requested while booting. We will apply the changes during
relocation (in a later commit).
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need this in U-Boot since we calculate it based on available memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remove the troublesome union hob_pointers so that some annoying casts
are no longer needed in those hob access routines. This also improves
the readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.
Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is the follow-on patch to clean up the FSP support codes:
- Remove the _t suffix on the structures defines
- Use __packed for structure defines
- Use U-Boot's assert()
- Use standard bool true/false
- Remove read_unaligned64()
- Use memcmp() in the compare_guid()
- Remove the cast in the memset() call
- Replace some magic numbers with macros
- Use panic() when no valid FSP image header is found
- Change some FSP utility routines to use an fsp_ prefix
- Add comment blocks for asm_continuation and fsp_init_done
- Remove some casts in find_fsp_header()
- Change HOB access macros to static inline routines
- Add comments to mention find_fsp_header() may be called in a
stackless environment
- Add comments to mention init(¶ms) in fsp_init() cannot
be removed
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.
Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Commit 65dd74a674 (x86: ivybridge: Implement SDRAM init) introduced
x86-specific asmlinkage into arch/x86/include/asm/config.h.
Commit ed0a2fbf14 (x86: Add a definition of asmlinkage) added the
same macro define again, this time, into include/common.h.
(Please do not add arch-specific stuff to include/common.h any more;
it is already too cluttered.)
The generic asmlinkage is defined in <linux/linkage.h>. If you want
to override it with an arch-specific one, the best way is to add it
to <asm/linkage.h> like Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Per Intel FSP architecture specification, FSP provides 3 routines
for bootloader to call. The first one is the TempRamInit (aka
Cache-As-Ram initialization) and the second one is the FspInit
which does the memory bring up (like MRC for other x86 targets)
and chipset initialization. Those two routines have to be called
before U-Boot jumping to board_init_f in start.S.
The FspInit() will return several memory blocks called Hand Off
Blocks (HOBs) whose format is described in Platform Initialization
(PI) specification (part of the UEFI specication) to the bootloader.
Save this HOB address to the U-Boot global data for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use inline assembly codes to call FspNotify() to make sure parameters
are passed on the stack as required by the FSP calling convention.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This is the initial import from Intel FSP release for Queensbay
platform (Tunnel Creek processor and Topcliff Platform Controller
Hub), which can be downloaded from Intel website.
For more details, check http://www.intel.com/fsp.
Note: U-Boot coding convention was applied to these codes, so it
looks completely different from the original Intel release.
Also update FSP support codes license header to use SPDX ID.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Option ROMs require a few additional descriptors. Add these, and remove the
enum since we now have to access several descriptors from assembler.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the Local Advanced Peripheral Interrupt Controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rename interrupt_init() in arch/x86/lib/pcat_interrupts.c to
i8259_init() and create a new interrupt_init() in
arch/x86/cpu/interrupt.c to call i8259_init() followed by a
call to cpu_init_interrupts().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since cpu_init_interrupts() was moved out of cpu_init_r(), it is
useless to keep cpu_init_r() for x86, thus remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Intel chips have a turbo mode where they can run faster for a short period
until they reach thermal limits. Add code to adjust and query this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards will want to do some setup before and after a PCI hose
is scanned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.
SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.
U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).
It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.
There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.
With this patch, link boots to a prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
The local advanced programmable interrupt controller is not used much in
U-Boot but we do need to set it up. Add basic support for this, which will
be extended as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
When not relying on Coreboot for GPIO init the GPIOs must be set up
correctly. This is currently done statically through a rather ugly method.
As the GPIOs are figured out they can be moved to the device tree and set
up as needed rather than all at the start.
In this implementation, board files should call ich_gpio_set_gpio_map()
before the GPIO driver is used in order to provide the GPIO information.
We use the early PCI interface so that this driver can now be used before
relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is convenient to be able to adjust MSRs with a structure that splits the
two 32-bit halves into separate fields, as they are often dealt with
separately. Add a few functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) includes an LPC (Low Pin Count) device
which provides a serial port. This is accessible on Chromebooks, so enable
it early in the boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add simple PCI access routines for x86 which permit use before relocation.
The normal PCI stack is still used, but for pre-relocation use there can
only ever be a single hose. After relocation, fall back to the normal
access, although even then on x86 machines there is normally only a single
PCI bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for using PCI before SDRAM is available, using early malloc()
and global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We want access PCI earlier in the init sequence, so refactor the code so
that it does not require use of a BSS variable to work. This will allow us
to use early malloc() to store information about a PCI hose.
Common PCI code moves to arch/x86/cpu/pci.c and a new
board_pci_setup_hose() function is provided by boards to set up the (single)
hose used by that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.
On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
This implementation has a 'cpu' prefix and returns a pointer to the string,
avoiding the need for copying.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to get the stack pointer and another to halt the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Return the saved TSC frequency in get_tbclk_mhz().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Use the same way that Linux does for quick TSC calibration via PIT
when calibration via MSR fails.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The CPU identification happens in x86_cpu_init_f() and corresponding
fields are saved in the global data for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The built in self test value is available in register eax on start-up. Save
it so that it can be accessed later. Unfortunately we must wait until the
global_data is available before we can do this, so there is a little bit of
shuffling to keep it around.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some functions are missing prototypes. Fix those that are specific to x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of an x86-specific cpu_init_f() function, use the normal U-Boot one
for this purpose. Also remove a useless/misleading comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of having an x86-specific DRAM init function, adjust things so we
can use the normal one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The boot_zimage() function is badly named it can also boot a raw kernel.
Rename it, and try to avoid pointers for memory addresses as it involves
lots of casting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to jump to a 64-bit Linux kernel. We need to set up a flat page
table structure, a new GDT and then go through a few hoops in the right
order.
Signed-off-by: Simon Glass <sjg@chromium.org>
There's a definition in stdint.h (provided by gcc) which will be more correct
if available.
Define CONFIG_USE_STDINT to use this feature, or USE_STDINT=1 on the 'make'
commmand.
This adjusts the settings for x86 and sandbox, with both have 64-bit options.
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@google.com>
Rewritten to be an option, since stdint.h is often available only in glibc.
Changed to preserve a clear boundary between stdint and non-stdint
Signed-off-by: Simon Glass <sjg@chromium.org>
This code doesn't follow the normal approach of having its arch-specific
definitions in an arch-specific directory. Add a new arch-specific file
and make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
The motivation of this commit is to change CONFIG_USE_PRIVATE_LIBGCC
to a boolean macro so we can move it to Kconfig.
In the current implementation, there are two forms of syntax
for this macro:
- CONFIG_USE_PRIVATE_LIBGCC=y
- CONFIG_USE_PRIVATE_LIBGCC=path/to/private/libgcc
The latter is only used by x86 architecture.
With a little bit refactoring, it can be converted to the former.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The x86 bootm code is quite special, and geared to zimage. Adjust it
to support device tree and make it more like the ARM code, with
separate bootm stages and functions for each stage.
Create a function announce_and_cleanup() to handle printing the
"Starting kernel ..." message and put it in bootm so it is in one
place and can be used by any loading code. Also move the
board_final_cleanup() function into bootm.
Signed-off-by: Simon Glass <sjg@chromium.org>
These options are used by the image code. To allow us to use the generic
code more easily, define these for x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some changes are needed to x86 timer functions to support tracing. Add
these so that the feature works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Coreboot provides a lot of useful timing information. Provide a facility
to add this to bootstage on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
While we don't want PCAT timers for timing, we want timer 2 so that we can
still make a beep. Re-purpose the PCAT driver for this, and enable it in
coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
This timer runs at a rate that can be calculated, well over 100MHz. It is
ideal for accurate timing and does not need interrupt servicing.
Tidy up some old broken and unneeded implementations at the same time.
To provide a consistent view of boot time, we use the same time
base as coreboot. Use the base timestamp supplied by coreboot
as U-Boot's base time.
Signed-off-by: Simon Glass <sjg@chromium.org>base
Signed-off-by: Simon Glass <sjg@chromium.org>
panic_puts() can be called in early boot to display a message. It might
help with early debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Wai-Hong Tam <waihong@chromium.org>
Since we use CONFIG_SYS_GENERIC_BOARD on x86, we don't need this anymore.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ pointed out that this code is no longer used. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
With CONFIG_OF_CONTROL we may have an FDT in the BSS region. Relocate
it up with the rest of U-Boot to keep the rest of memory free.
Signed-off-by: Simon Glass <sjg@chromium.org>
With this symbol we can easy append something (e.g. an FDT) to the U-Boot
binary and access it from within U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to access the timer before U-Boot has relocated
so that we can fully support bootstage.
Add new global_data members to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is pretty old and we want to support only 32-bit systems now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
This x86 CPU variant is no longer required as the boards that use it have
been removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
The libfdt.h file is the definition file for libfdt. It is unnecessary
to include other fdt header files (the necessary ones are pulled in
by libfdt.h).
Signed-off-by: Gerald Van Baren <gvb@unssw.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
and, if including libfdt.h which includes libfdt_env.h in
the correct order, don't include fdt.h before libfdt.h.
this is needed to get the fdt type definitions set from
the project environment before fdt.h uses them.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add arch/x86/cpu/cpu.c changes after Graeme's comments]
Signed-off-by: Tom Rini <trini@ti.com>
We plan to move architecture-specific data into a separate structure so
that we can make the rest of it common.
As a first step, create struct arch_global_data to hold these fields.
Initially it is empty.
This patch applies to all archs at once. I can split it if this is really
a pain.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not intended to be exported from the video drivers, so
remove the prototype. This fixes an error:
cfb_console.c:1793:12: error: static declaration of 'video_init' follows non-static declaration
Signed-off-by: Simon Glass <sjg@chromium.org>
These were removed, but actually are useful.
Cold means that we started from a reset/power on.
Warm means that we started from another U-Boot.
We determine whether u-boot on x86 was warm or cold booted (really if
it started at the beginning of the text segment or at the ELF entry point).
We plumb the result through to the global data structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
If we have SPI support, make sure that we init it.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vic Yang <victoryang@chromium.org>
These types should be 64 bits long to reflect the fact that physical
addresses and the size of physical areas of memory are more than 32 bits
long.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
To maintain the initialization state of the timestamp facility, thesq
pointer to the CBMEM section containing the timestamp table should be
kept in the .data section (so that it is maintained across u-boot
relocation).
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This change turns on the code which allows u-boot to add
timestamps to the timestamp table created by coreboot.
Since u-boot does not use the tsc_t like structure to represent
HW counter readings, this structure is being replaced by 64 bit
integer.
The timestamp_init() function is now initializing the base timer
value used by u-boot to calculate the HW counter increments.
Timestamp facility is initialized as soon as the timestamp table
pointer is found in the coreboot table. The u-boot generated
timer events' ID will start at 1000 to clearly separate u-boot
events from coreboot events in the timer trace.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Put this function in the u-boot-x86.h header file. We could instead create
timer.h perhaps.
We support setting a base time, and reading the time relative to this base.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement <asm-generic/gpio.h> functions for Intel ICH6 and later.
Only GPIOs 0-31 are handled by this code.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch prevents u-boot from "spamming" random progress codes on
a port 80 "post card".
The previous version of this patch just removed the delays in the "slow"
IO functions, as they do not need to be slow, however, this patch is
less intrusive.
It uses another unused port that is often used by BIOSes (and the Linux
Kernel) for small delay timing purposes.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The i386 version of io.h depends on the phys_addr_t type which is defined in
types.h. It wasn't including that explicitly, and was working presumably
because the other files including it had already included types.h themselves
directly or indirectly. This change fixes that.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function provides an opportunity for some last minute cleanup and
reconfiguration before control is handed over to Linux. It's possible this
may need to do something in the future, but for now it's left empty. It's set
up as a weak symbol so it can be overridden if necessary on a case by case
basis.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This change adds a pointer to the global data structure in x86 to point to
the device tree. This mirrors an identical pointer in ARM.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for decoding tags for GPIOs, compile/build info, cbmem and
other features.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot needs a host controller or "hose" to interact with the PCI busses
behind them. This change installs a host controller during initialization of
the coreboot "board" which implements some of X86's basic PCI semantics. This
relies on some existing generic code, but also duplicates a little bit of code
from the sc520 implementation. Ideally we'd eliminate that duplication at some
point.
It looks like in order to scan buses beyond bus 0, we'll need to tell u-boot's
generic PCI configuration code what to do if it encounters a bridge,
specifically to scan the bus on the other side of it.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
I suspect these includes were usually available because something else
included them earlier or because they were brought in transitively.
Change-Id: I6aae2ac94dc792eac6febb4345e8125f69f70988
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Putting global data on the stack simplifies the init process (and makes it
slightly quicker). During the 'flash' stage of the init sequence, global
data is in the CAR stack. After SDRAM is initialised, global data is copied
from CAR to the SDRAM stack
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
So it can be used as a type in struct global_data and remove an ugly typecast
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Create an init function array for board_init_f_r - This finalises the
migration to a purely array based initialisation mechanism
Also tweak a few comments while we are at it so everything is 'correct'
--
Changes for v2:
- Renamed to a more apt name
- Fix bug in set_reloc_flag_r
- Re-instate gd->flags = boot_flags; in board_init_f
- Added commit message
This patch moves towards reducing board.c to simply a set of init cores for
the three initialisation phases (Flash, Flash/RAM, and RAM), a set of three
init function arrays and a init function array processing function
Use the base address of the 'F' segment as a pointer to the global data
structure. By adding the linear address (i.e. the 'D' segment address) as
the first word of the global data structure, the address of the global data
relative to the 'D' segment can be found simply, for example, by:
fs movl 0, %eax
This makes the gd 'pointer' writable prior to relocation (by reloading the
Global Desctriptor Table) which brings x86 into line with all other arches
NOTE: Writing to the gd 'pointer' is expensive (but we only do it
twice) but using it to access global data members (read and write) is
still fairly cheap
--
Changes for v2:
- Rebased against changes made to patch #3
- Removed extra indent
- Tweaked commit message
Move the relocation offset calculation out of assembler and into C. This
also paves the way for the upcoming init sequence simplification by adding
the board_init_f_r flash to RAM transitional function
--
Changes for v2:
- Added commit message
- Minor adjustment to new stack address comment
If vboot successfully verifies a kernel, it will leave it in place and
basically ready to boot. The zeropage table which is part of the x86 boot
protocol is at the end of the kernel, though, instead of the beginning, and
because the image is already in place there's no need to copy it around.
This change refactors the code which implements the zboot command so that
the configuration of the zeropage table and loading the pieces of the
kernel into memory are done separately. Also, because the command line goes
before the zeropage table in vboot which is somewhat incompatible with the
normal protocol, where to put the command line is a now a parameter instead
of being hard coded.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
This change conditionally modifies the zboot command so that it can use the
32 bit boot protocol. This is necessary because the 16 bit realmode entry
point assumes that it can call BIOS services which neither coreboot nor
u-boot provide.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
This change cleans up some formatting issues in the zimage handling code, and
converts it from using offsets added to a base pointer to using the available
structure definitions which were already being included.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
This change also forces the lib_sysinfo structure to be in the .data
section. Otherwise it ends up in the .bss section. U-boot assumes that it
doesn't need to copy it over during relocation, and instead fills that
whole section with zeroes. If we really were booting from ROM that would be
appropriate, but we need some information from the coreboot tables (memory
size) before then and have to fill that structure before relocation. We
skirt u-boot's assumption by putting this in .data where it assumes there
is still read only but non-zero data.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
The new implementation is about twice as fast as the old. This is from
glibc-2.14, sysdeps/i386/memset.c.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
