The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Add DT entries for main domain watchdog0 and 1 instances on the J721e
well as RTI1-based watchdog on the AM65x. RTI0 does not work for this
purpose on the AM65x, so leave it out.
On AM65x, we mark the power-domain as shared because RTI firmware such
as https://github.com/siemens/k3-rti-wdt may request it as well in order
to prevent accidental shutdown of the watchdog.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add LED support for Cortina Access Presidio Engineering Board
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Simon Glass <sjg@chromium.org>
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI
partitions.
Additionally enable the UBI commands in crs305-1g-4s_defconfig.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
removed, is not necessary, error at out-of-tree building.
'#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
renamed to env_get(), env_get_ulong(), env_set() and env_save(),
respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
appropriate functionality is not supported yet. New mmc-property
"mmcboost" added.
s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
This introduces initial support for the popular Qualcomm
IPQ40x8 and IPQ40x9 WiSoC series.
IPQ40xx series have 4x Cortex A7 ARM-v7A cores.
Supported are: IPQ4018, IPQ4019, IPQ4028 and IPQ4029.
IPQ40x8 and IPQ40x9 use the same cores, but differ in
addressable RAM size (1GB for IPQ40x9 and 256MB for IPQ40x8)
and supported peripherals (IPQ40x8 lacks RGMII, LCD controller
and EMMC/SDHCI controllers).
IQP4028/IPQ4029 models differ from IPQ4018/IPQ4019 only
by their rated temperatures rates with IPQ402X models being
rated for wider temperature ranges.
Initially this supports:
* Simple clock driver (Only for UART1 now, will be extended)
* Pinctrl driver (Supports UARTX and GPIO now, will be extended)
* GPIOs already supported by msm_gpio driver with updates
* UARTs already supported by serial_msm driver with updates
Further peripherals will come in later patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
On mediatek various files that need to be created by binman. It does not
make sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Also update the binman definition so that idbloader.img is only needed
when SPL is actually being used.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple binman config and enable CONFIG_HAS_ROM so that U-Boot
produces a ROM for jerry.
Change the binman image definition to support multiple images, since it
may be used to build both u-boot-rockchip.bin and u-boot.rom
Signed-off-by: Simon Glass <sjg@chromium.org>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.
This works with generic stm32mp1 config.
Right now only booting from SD card is supported.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 792919241b.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 3c2e2a1a79.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
STM32 serial IP can be reset via reset controller.
Add the support of reset to uart nodes on stm32mp15-u-boot.dtsi,
the ad-dons file for U-Boot.
This patch fix issues when previous UART configuration, for example
done in TF-A or ROM code, is not handled in U-Boot stm32 serial driver
init.
This reset property won't be not added in Linux kernel device tree
as this reset is not used in Linux STM32 serial driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove hnp-srp-disable for usbotg node because this feature is only needed
for usbotg in HOST mode (in drivers/usb/host/dwc2.c)
and this feature is not activated in stm32mp15 U-Boot
(stm32mp15_basic_defconfig and stm32mp15_trusted_defconfig);
only the device mode is activated and OTG is not supported in DWC2 driver.
This patch reduces the difference between U-Boot and Linux kernel
device-tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DT alignment with Linux kernel v5.8-rc1 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Alignment with pins name used in Linux kernel v5.8.
It is a preleminary step for device tree alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save the environment at the end of the U-Boot partition, the GPT
partition named "ssbl" in SD card or eMMC and avoid requirements
on the "bootfs" file system generated via specific raw tools
(like wic and genimage).
With the previous configuration of the U-Boot environment saved in ext4
file, U-Boot need to create/modify the file uenv.txt in the ext4 file
system; so this EXT4 file system need to be generated without some
functionality, like metadata_csum and dir_index, because they are not
supported by U-Boot.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Add the PCIe EP node for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev2 requires 4KB space for type0 and 4KB
space for type1 iATU window. Increase configuration
size to 8KB to have sufficient space for type0
and type1 window.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch imports the device tree and required bindings to permit
the device tree to build for the R8Z774A1 (RZ/G2M).
Signed-off-by: Adam Ford <aford173@gmail.com>
Add u-boot,spl-boot-order for ROCKPi N10, so-that it can able
to boot from eMMC and SDMMC in order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable PCIe for RockPI N10.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and the quirk in
ohci platform driver will disable ohci on rk3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This sync has changes required to use HDMI CEC pin in U-Boot.
Sync dts from linux v5.8-rc5 commit:
"ARM: dts: rockchip: define the two possible rk3288 CEC pins"
(sha1: 838980dd04e994bf81cf104fa01ae60802146b39)
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
OF graph endpoint connections must be bidirectional and dtc warn if they
are not. i.MX7 based DTs have an error and generate
warnings:
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/replicator/ports/port@0/endpoint: graph connection to node
'/soc/tpiu@30087000/port/endpoint' is not bidirectional
arch/arm/dts/imx7d-sdb.dtb: Warning (graph_endpoint):
/soc/tpiu@30087000/port/endpoint: graph connection to node
'/replicator/ports/port@1/endpoint' is not bidirectional
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add Phytec Mira device tree files, for use with pcm058.
>From Linux 5.6, commit 7111951b8d49 upstream
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Sync DT bindings from kernel DT and move them to out of -u-boot.dtsi
files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Several MMC drivers use GPIO for card detection with cd-gpios property in
the MMC node pointing to a GPIO node. However, as U-Boot tries to save
space by keeping only required nodes using u-boot* properties, several
devices tree result in having only in the MMC node but not the GPIO node
associated to cd-gpios.
This patch, fixes several ocurrence of this issue.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
The spi0 alias is needed by the environment code to retrieve the SPI
flash. This patch adds some -u-boot.dtsi files, providing the spi0
aliases, for all the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Note that this -u-boot.dtsi files will be removed as soon as the spi0
aliases will be available in the upstream Linux dtsi files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
The PHY needs a reset in order to be functionnal for U-Boot, add the old
PHY reset bindings for dwmac until we support the new bindings in the PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This imports the changes and the new Odroid-C4 board from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This patch adds node for ethernet controller found on Action Semi OWL
S700 SoC.
Since, there is no upstream Linux binding exist for S700 ethernet
controller, Changes are put in u-boot specific dtsi file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl8EgGEACgkQ4rK92eCq
k3V7mwf+N5Iq6CbUPP11mFiNgAFZ5+hcn6gBTWvbjnd+oaIp15hiQrUNusGNFxXe
oyM4fvm12tjuWFlA0U6VtiLhuVQB1Yte048oX+edDCCLGwxkp6cKBHtCaGT14XvY
ow60XInv/dlrINumf8isy+5QlLgT1Cb7aGZN1qRHsUtnHB/IC836KO+hukGRUvk3
Lqz+FbHqitKnL+CIboC2+YzXqG6ZXdixFZVVPmTVd34C8hQOdkExJ//uR/lH/s6f
vjaecs7HpIuKRpKpt5WcoLzTLd1hstqNNhmTbBHmVo+EqIjMkpISUwDpDJNU5pki
BPbdG9VXqb46JLaTtPT+U4gX4yJ3Bw==
=jQCC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl8DHgAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyAdDCACFX01IPRmdkNEYrJf0
YfhQPAPZ/5EyHBv36ePl93CbIRnJPpnrGbBXe8+/Jdcq7l6EkJh2cuO+t9axXner
m0kH35LzLiR9Olz6q5Su0InPWpnDtXxtIczK5v7ZHBeMZ2so763e7SQ2VIMyJJb/
VT6hilqJK6+W1c2X1wmzxyh/nnv/bDBz97cavJN1EKw1arYr8jh/8/tpABk5msDm
J6Z5WsS/CYk7cj6hX7dSNRfqcKsjl/gCYjnVssfgaP1sH+NX0mtS8C6zchNILmpB
2T/dKnpYBBAWTD5fGNVKxKphAuZgQHw51AJhkOnYDrMKisifFC0ssvxkh+nvwyTm
1w4R
=1YzJ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.10 cycle
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa dalang carrier boards are used to mount vmarc SoM's
of rk3399pro and rk3288 to make complete SBC.
Among these combinations, card detection gpio, max-frequency
properties are used with rk3399pro SoM but not required for
rk3288 SoM based on the hardware schematics.
So, let's move these sdmmc specific properties on associate
vmarc dtsi to make common use of dalang carrier device tree file.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Carrier board often referred as baseboard. For making
complete SBC or any other industrial boards, these
carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board
peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI,
eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board
Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
So add this carrier board dtsi as a separate file in
ARM directory, so-that the same can reuse it in both
rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
VMARC RK3399Pro SOM is a standard SMARC SOM design with
Rockchip RK3399Pro SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3399Pro
- PMIC: RK809-3
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3399Pro SOM, this would use
with associated carrier board.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rng so UEFI can provide entropy for KASLR
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Since commit:
commit 6333cbb381
Author: Michael Walle <michael@walle.cc>
Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
, the clock output setting for the AR803x driver is removed from being
hardcoded in the PHY driver and should be passed via device tree instead.
Update the device tree with the "qca,clk-out-frequency" property so that
Ethernet can work again.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change mini u-boot qspi spi-max-frequency to 108Mhz, make the
frequency similar to full u-boot qspi flash spi-max-frequency.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Sync the device tree with 5.8-rc1.
It basically contains the following extra kernel commit:
commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09
Author: Russell King <rmk+kernel@armlinux.org.uk>
Date: Wed Apr 15 16:44:17 2020 +0100
ARM: dts: imx6-sr-som: add ethernet PHY configuration
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
, which passes the 'qca,clk-out-frequency' property and it is important
to specify the correct frequency generated by the AR8035.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This avoid potential issue for SDCard boot:
the card detect fails with floating gpio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The PSCI nodes are currently not populated for the Tegra210 and Tegra186
devices. This prevents the PSCI driver from being able to identify the
PSCI method used by these devices and causes the probe of the PSCI
driver to fail.
Since commit 81ea00838c ("efi_loader: PSCI reset and shutdown") was
added, which moves the PSCI EFI system reset handler into the PSCI
driver, this has prevented the EFI system reset from working for
Tegra210 and Tegra186. Therefore, populating these nodes is necessary
to fix the EFI system reset for Tegra210 and Tegra186.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Copy all device tree files required for omap4 sdp4430 support from
mainline Linux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is
needed since commit [1] that changed U-Boot/stm32mp15 to detect
OP-TEE availability by probing the resource instead of relying on
U-Boot configuration. The software sequence implemented by [1] is
fine but U-Boot DTS/DTSI files were not updated accordingly since,
hence OP-TEE presence is never detected by U-Boot, preventing Linux
kernel from using OP-TEE resources.
For consistency and to synchronize stm32mp15 DTSI files (excluding
U-Boot specific DTSI files) with the Linux kernel ones, this change
also moves the OP-TEE reserved memory nodes from board generic DTSI
files to U-Boot specific board DTSI files.
Link: [1] commit 43df0a159d ("stm32mp1: dynamically detect op-tee presence")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change DT compatibility name to match change in driver's name.
Remove unused io_ds and fifo_mode fields from DT.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
Commit e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
change the hcnt and lcnt timing calculation. New timing calculation is
based on calculation from Designware i2c databook.
After this new timing calculation, hcnt will have negative value
with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts.
This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall
time used in Designware i2c driver) for Uboot.
Before the fix:
=> i2c dev 0
Setting bus to 0
Failure changing bus number (-22)
After the fix:
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Accidentally submitted a patch with indentation not correct, let's fix it
by indenting wrong lines.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tabs not spaces, so transform it to the common styling.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.
Make the usbhost-supply work again by bringing them in sync again.
This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.
This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl7YxFMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyJnICACR6Q6OclfIuM0A3ubV
GV48+iVz55eZnrZFKkbALBNjwTsshLpdZ/7Lr4zPD5e/FmrbJ+RONd0B6E38fSJk
Rq1ZwMyuR6yv+LAb9+La36tGqD9bCFewqBpR5LQNOdjE+fG66rrWxksMME1jOIr5
FLpFkk3lmEUloQumHDCQUgzXC/TUWpedgxpT15l1nR/Ovkh/MPvggIdS2zMWw92J
oA9shaNTVLd//W9icduXagNtRMsjscmf/zTZFCYgBRjUZgiPW+HnitWg7jqbYIuY
AqmNBZIrC6OuZ7W447g1rMGwbwQ5T9vbydp6PpHVqPvTt3D8OZ9h1+Hwwie7u9O1
CPaV
=xLcT
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.07 cycle
This set includes just two small commits that fix a build warning and
add a missing serial node.
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
Sync initial support for Pinebook Pro device tree from Linux 5.7-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host
for Rockchip RK3399 Evaluation Board.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add u-boot,spl-boot-order as sdhci and sdmmc for booting
from eMMC and SD card.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux v5.7-rc1 dts(i) sync has changed the sdmmc node from
dwmmc@fe320000 to mmc@fe320000 and this ofpath is being
used in rockchip spl bootdevice code.
So, update the ofpath with a new node name and prefix "same-as-spl"
to missing u-boot,spl-boot-order.
Bug log:
U-Boot SPL 2020.07-rc2-00256-g9c5fef5774 (May 24 2020 - 20:20:43 +0530)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux"
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The khadas-vim, khadas-vim2, libretech-ac & libretech-*-pc boards were missing
DT tweak to enable USB gadget.
Add them to their -u-boot.dtsi files and include the right gxl-u-boot.dtsi.
Fixes: a19e8a0f03 ("arm: dts: meson-gxl: Add USB Gadget nodes for U-Boot")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Include the common g12 u-boot tweaks to permit enabling video output tweaks
on Khadas VIM3 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disable SDR104 mode until we know it is really stable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The I2C2 uses different pinmux on AV96, use correct pinmux and
also add comments about the I2C being present on the "low-speed"
expansion connector X6.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Commit f49ac7e1c4 switched the default PHY speed to 3.125Gbit to resolve
issues with SFP modules. However, U-Boot does not have a "2500base-x"
phy-mode.
Resolve this by using "sgmii-2500" instead.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Without this U-Boot-specific property, booting on the Synology DS414
(or DS214+) fails in SPL. The spi0 DT node is not scanned, as a result
the SPI flash cannot be found.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
adapting commit fa2047c473 ("rockchip: rk3328: enable spl-fifo-mode
for emmc and sdmmc") for rk3399.
Since mmc to sram can't do dma, add patch to prevent aborts transferring
TF-A parts.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Enable DDR52 modes, since the SD core supports correct switching now.
For completeness, list HS200 modes, however those were already enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reserve 4 kiB of space in R-Car Gen3 DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node
and possibly also additional /memory@ nodes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
With the converstion of SMC911x to DM, this can facilitate the omap3
boards from LogicPD (now called Beacon EmbeddedWorks) to be converted.
There isn't a clean solution to doing this in phases, so the boards are
all being done together to avoid breaking functionality.
Because the GPMC bus hasn't been converted, the -u-boot.dtsi node needs
to show the address of the ethernet controller for each board.
The board file, which is common betwen the OMAP35 and DM37 SOM LV and
Torpedo boards, can remove the manual ethernet initialization, but it
still needs to register the address and GPMC configuration for the Ethernet
controller which is now being moved around to board_late_init().
Lastly, this patch updates the various config files to add the reference
for DM_ETH and remove the SMC address, which is now fetched from the
newly created device tree nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
EMIF tool for AM65x [1] is now updated from rev 1.98 to 2.02
This update includes
* Optimizations in IO configuration.
* Fix for byte enablement in GCR registers.
* Fixes for PG2.0 including ZQ control.
[1]: http://www.ti.com/lit/zip/sprcah7
Acked-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.
This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
* SD #1: 3, 7, 19, 20
* SD #2: 11
Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.
Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The LX2160A processor has two external MDIO interfaces, described in the
DTS as emdio1 and emdio2.
On the LX2160AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as eight input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 8 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, DPMAC 17 and 18 are updated to reference the on-board PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add nodes for DPMACs 1, 2 and 5-6 which were missing from the
description. These will be later used on the LX2160AQDS specific DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to new qspi driver, some properties like "bus-num, num-cs,
big-endian" are no longer used. Device endiannes can be determined from
device-type data in driver.
Now use board specific compatibles, generic node names and specific
labels to align with linux device-tree properties.
Also consolidate spi-max-frequency to 50Mhz treewide.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds support for uart4 to the
processor level device tree include file.
Signed-off-by: Tiaki Rice <tiakirice@hotmail.com>
Cc: Eugen Hristev <Eugen.Hristev@microchip.com>
A defconfig is added on lx2160ardb which allows UEFI variable management
via OP-TEE. Enable the the node in the relevant DTS file.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
-----BEGIN PGP SIGNATURE-----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=66oV
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- fix phy configuration for RPi4's bcmgenet
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
DT alignment with Linux 5.7-rc2, including the kernel commits
431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add custom DDR DRAM settings for the DHCOR and DHCOM SoMs and put them
into use by the board file instead of the default ones. These new DRAM
settings are a better fit for the SoMs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The commit 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM
and AV96 board") was not applied correctly and in full, and omitted
an important split of the SoM into 3V3 and 1V8 options. The Avenger96
board is based on the 1V8 IO option of the DHCOR SoM, however this is
an optional modification of the 3V3 IO DHCOR SoM with extra on-SoM
regulator to cater for the 96boards 1V8 IO requirements.
Reinstate the split between the 1V8 and 3V3 IO variants.
Fixes: 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the DDR3 dtsi files generated by STM32CubeMX 5.6.0
Speed Bin Grade = using DDR3-1066G / 8-8-8 and all others
parameters at default value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Force boot-led ON and no more rely on default-state.
This patch avoid device-tree modification for U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
At present the pinctrl nodes are not enabled in pre-relocation U-Boot so
the UARTs do not correctly select the pinconfig to enable the UART pins.
Fix this so that the U-Boot banner is printed.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 9821636b64 (bcm2835_pinctrl: Probe pre-reloc)
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This resolves issues with certain SFP modules.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
