During LPDDR initialization we will loop through a series of frequency
changes in order to train at the various operating frequencies. During
this training, accessing the DRAM_CLASS bitfield could happen during a
frequency change and cause the read to hang.
Store the DRAM type into the main structure to avoid multiple readings
while the independent phy is training.
Signed-off-by: Bryan Brattlof <bb@ti.com>
StarFive VisionFive 2 has two versions, 1.2A and 1.3B, each version of
DDR capacity includes 2G/4G/8G, a DT can not support multiple
capacities, so the capacity size information is recorded to EEPROM, when
DDR initialization required capacity size information is read from
EEPROM.
If there is no information in EEPROM, it is initialized with the default
size defined in DT.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Driver for Cadence EDAC DDR controller, as found in the Renesas RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so convert regmap_init_mem_plat() input to handel both. The
syscon class driver also makes use of the regmap_init_mem_plat()
function, but has no way of knowing the format of the
device-specific platform data. In case of odd reg structures other
then that the syscon class driver assumes the regmap must be
filled in the individual syscon driver before pre-probe.
Also fix the ARRAY_SIZE divider in the syscon class driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
For 2 GB LPDDR4 single-rank RAM with 16 rows, the Rockchip ddr init bin
prints:
"Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB"
U-Boot TPL prints:
"BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB"
Add missing high row detection so that U-Boot TPL prints Row=16, same as
the Rockchip ddr init bin:
"BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB"
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add driver for StarFive JH7110 to support ddr initialization in SPL.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
A condition in the rk3399 RAM initialization code used the old
CONFIG_RAM_RK3399_LPDDR4 constant name. This commit changes the
condition to use the correct CONFIG_RAM_ROCKCHIP_LPDDR4 constant.
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Add ddr driver for rk3588 to get the ram capacity.
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Control the ddr init print messages via RAM_ROCKCHIP_DEBUG
instead of printing by default.
This gives an option to configs to enable these prints or
not.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add full ddr pctl registers and bit masks for px30.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DDR chip capacity is computed based on GRF split in some
Rockchip SoC's like PX30 and RV1126.
Add split argument in ddr print info so-that the respective
ddr driver will pass the grf split.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We have common ddr types in rockchip or in general. So use
the common ddr type names instead of per Rockchip SoC to
avoid confusion.
The respective ddr type names will use on the associated
ddr SoC driver as these drivers are built per SoC at a time.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ram-uclass is building irrespective of whether TPL_DM
or SPL_DM is enabled. So control the ram uclass build
based on TPL/SPL_DM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TI's am62a family of SoCs uses a new 32bit DDR controller that shares
much of the same functionality with the existing am64 and j721e
controllers.
Select this controller by default when u-boot is build for the am62a
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The new 32bit DDR controller for TI's am62a family of SoCs shares much
of the same functionality with the existing 16bit (am64) and 32bit
(j721e) controllers, so this patch reorganizes the existing
auto-generated macros for the 16bit and 32bit controllers to make room
for the macros for the am62a's controller
This patch consists mostly of header/macro renames and additions with a
new Kconfig option (K3_AM62A_DDRSS) allowing us to select these new
macros during compilation.
Signed-off-by: Bryan Brattlof <bb@ti.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Adjust the following settings to get better timing and signal quality.
1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]
2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]
3. CLK/CA timing
- 0x1e6e01a8[31]
4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])
Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6). This patch introduces macros to synchronize
the MR value on both sides.
Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The condition "~data" in the if-statement is a typo. The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.
Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].
Fixes: fde9314346 ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
RAM_PX30_DDR4 is for DDR4 support and not DDR3 so let's fix the typo.
Fixes: 2db36c64bd ("ram: rockchip: px30: add a config-based ddr selection")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The i.MXRT11 series has different offsets for IOCR_MUX, it also can
address 64MiB of SDRAM so add a macro for that.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/
Suggested-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Frequency changes to 400MHz are presently reported as:
lpddr4_set_rate_0: change freq to 400000000 mhz 0, 1
This is obviously wrong by 6 orders of magnitude.
Ensure frequency changes are reported accurately.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Functions pointed to by this op pointer can return non-zero values
indicating an error. Ensure any error value is propagated back up the
call-chain.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Only add the dram channel when we finally setup it successfully at the
last step.
Signed-off-by: Han Pengfei <pengphei@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DRAM ASR, auto self-refresh, conditionally, based on DT PWRCTL
register bits. While ASR does save considerable amount of power at
runtime automatically, it also causes LTDC underruns on large panels.
Let user select whether or not ASR is required or not, generally ASR
should be enabled on portable and battery operated devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The k3-ddrss driver wants to configure the DDRSS_V2A_CTL_REG to reflect
the maximum possible SDRAM of 2 GB for AM64x (instead of the register's
default that says 8 GB, which the AM64x DDR controller wouldn't support).
The offset 0x20 was correct, but the register name DDRSS_V2A_R1_MAT_REG
was that of the next register at offset 0x24.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
