The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Enabling configs for GPIO CMD, EXYNOS4 family and replacing
exynos_gpio_get with new linear GPIO pin number required
because of the new function asking only 2 arguments (pin
and value) instead of 3 (bank, pin and value).
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding two configs:
* CONFIG_FIT - Enable FIT image support.
* CONFIG_FIT_BEST_MATCH - Enable fetching correct DTB from
FIT image by comparing compatibles.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some new boards define CONFIG_SYS_HZ again! Remove.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.
In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Some machines do not have SDL libraries installed, and it is still useful
to build sandbox without LCD/keyboard support.
Add an option for this, used as follows:
make sandbox_config all NO_SDL=1
Signed-off-by: Simon Glass <sjg@chromium.org>
This checks if the 7" WVGA produced by Future Eletronics is detected
and pass the needed kernel arguments for it to work.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
"mmc boot" command didn't use anywhere.
It can be replace "mmc dev" command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the fe60164 commit.
This commit restores proper setting of default console for the
trats board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the 1ecab0f commit.
This commit restores proper setting of default console for the
trats2 board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- expand the condition with CONFIG_OF_CONTROL
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Future patches will make DFU too large to fit in this board's SPL build.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.
I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.
Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.
Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.
CONFIG_USB_CABLE_CHECK was removed.
Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since highbank is actually shared between Highbank and Midway platforms,
remove the Highbank name from the prompt and use the default.
Signed-off-by: Rob Herring <robh@kernel.org>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
MACH_TYPE_LAGER and CONFIG_MACH_TYPE are not already available on Lager board.
This removes them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_SH_TMU_CLK_FREQ of lager is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_SH_TMU_CLK_FREQ of koelsch is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With 32 milliseconds delay on some boards EEMPROM got written inconsistently.
With 64 msec all of our existig boards show properly written EEPROM.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot binary size has been increased from 512KB to 768KB.
So update CONFIG_SYS_MONITOR_LEN to reflect the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB_PI board does not have QE connector.
So disable CONFIG_QE and CONFIG_U_QE for T1042RDB_PI
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.
This support of CPLD includes
- files and register defintion
- Commands to swtich alternate bank and default bank
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.
Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
NOR flash is on CS1 instead of CS2 when NAND boot.
So correct NOR chip selection to CS1 from CS2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.
Signed-off-by: York Sun <yorksun@freescale.com>
add CONFIG_QE, CONFIG_U_QE and CONFIG_SYS_QE_FW_ADDR into
"include/configs/T1040RDB.h"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR, SPI and SD secure boot targets for BSC9132QDS.
Changes:
- Debug TLB entry is not required for Secure Boot Target.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The workaround for IFC errata A003399 was not enabled
in case of secure boot. So, secure boot from NOR was not
working.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
This patch converts the MIPS Malta development board to make use of the
generic board code now that it is supported on MIPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/lubbock/*
- Remove include/configs/lubbock.h
- Cleanup defined(CONFIG_LUBBOCK)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove include/configs/EVB64260.h
- Remove the entry from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rsdproto/*
- Remove include/configs/rsdproto.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rpxsuper/*
- Remove include/configs/RPXsuper.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/RPXlite/*
- Remove board/RPXClassic/*
- Remove include/configs/RPXlite.h
- Remove include/configs/RPXClassic.h
- Clean-up defined(CONFIG_RPXCLASSIC)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
- Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
- Remove the entries from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/genietv/*
- Remove include/configs/GENIETV.h
- Clean-up if defined(CONFIG_GENIETV)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <nm@ti.com>
This is more in line with commits
664979a2a9f764b63b8094458b87247d254b0cc1(omap3_beagle: remove JFFS2
support.) and 102ce9ea7a (omap3_beagle:
enable CMD_FS_GENERIC and simplify load of image/ramdisk)
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)
Signed-off-by: Nishanth Menon <nm@ti.com>
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic
functionality Further information in doc/README.generic-board
Signed-off-by: Nishanth Menon <nm@ti.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
currently only spi0 is enabled on k2hk evm. This
configuration update is needed to enable spi1 and spi2.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
- add davinci driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Convert to using the common config files. This requires a little more
flexibility in the common files than we had been using before.
Signed-off-by: Tom Rini <trini@ti.com>
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This is only useful with the _spiboot build target anyhow, so only
include it then. Drop CONFIG_SPL_OS_BOOT support then as the flash is
small and didn't include a spot for the device tree already.
Signed-off-by: Tom Rini <trini@ti.com>
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree. In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: Tom Rini <trini@ti.com>
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: Tom Rini <trini@ti.com>
This mainly converts the am335x_spl_bch driver to the "normal" format
which means a slight change to nand_info within the driver.
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RiOTboard is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- HDMI output
- I2C 1/2/3
- LVDS TFT with LCD8000-97C from Embest/Element 14
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
MarSBoard is produced by Embest/Element 14 and is based on i.MX6 Dual
The following features are tested :
- UART2 (console)
- eMMC
- uSDCard
- Ethernet
- USB Host (through 2 ports hub)
- HDMI output
- I2C 1/2
- SPI NOR Flash
- LVDS TFT with LCD8000-97C from Embest/Element 14
Boot on SPI NOR and through USB loader are tested.
For more informations on this board :
http://www.embest-tech.com/shop/star/marsboard.html
Both boards are supported by the same code base as they are based on a
common trunk of schematics.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit d016dc42ce changed the layout of BCH8 SW
on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle
driver to avoid wrong ecc errors.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This change enables automatically uuid generation by command gpt.
In case of updating partitions layout user don't need to care about
generate uuid manually.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
The u-boot's image TEXT_BASE needs to be changed to 0x43e00000 from 0x78100000.
This change provides compatibility with other trats2 (RD_PQ) devices
(http://download.tizen.org/releases/system/).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on M53EVK and adjust the rest of the macros accordingly
to use the detected values.
An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fix memory access slowness on i.MX53 M53EVK board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On M53EVK,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.
The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:
0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)
This is past the DRAM available in the first bank on M53EVK, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.
There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on MX53QSB and adjust the rest of the macros accordingly
to use the detected values.
An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fix memory access slowness on i.MX53 MX53QSB board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On MX53QSB,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.
The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:
0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)
This is past the DRAM available in the first bank on MX53QSB, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.
There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Add support for PCIe on MX6 SabreSDP board and enable the support
in the config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>
Use of PCIe on SABRE Lite and Nitrogen6x boards
is atypical and requires the use of custom daughter
boards.
Use in U-Boot is even rarer, so this patch removes it from
the standard configuration.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
CONFIG_BOOT_INTERNAL is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add yet another OCOTP driver for this i.MX family. This time, it's a driver for
the OCOTP variant found in the i.MX23 and i.MX28. This version of OCOTP is too
different from the i.MX6 one that I could not use the mxc_ocotp.c driver without
making it into a big pile of #ifdef . This driver implements the regular fuse
command interface, but due to the IP blocks' limitation, we support only READ
and PROG functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.
As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.
Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
On the boards this target supports this option is either non possible
without hardware mods (Beaglebone White/Black) or not supported due to
board design. Drop this and regain some space.
Signed-off-by: Tom Rini <trini@ti.com>
This allows to use exynos random number generator by enabling configs:
- CONFIG_EXYNOS_ACE_SHA
- CONFIG_LIB_HW_RAND
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Minkyu Kang <mk7.kang@samsung.com>
New configs:
- CONFIG_LIB_RAND - to enable implementation of rand library in lib/rand.c
- CONFIG_LIB_HW_RAND - to enable hardware based implementations of lib rand
Other changes:
- add CONFIG_LIB_RAND to boards configs which needs rand()
- put only one rand.o dependency in lib/Makefile
CONFIG_LIB_HW_RAND should be defined for drivers which implements rand library
(declared in include/common.h):
- void srand(unsigned int seed)
- unsigned int rand(void)
- unsigned int rand_r(unsigned int *seedp)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
as the siemens boards use dfu for updating a nand ubi partition
add DFU_MANIFEST_POLL_TIMEOUT to them, so dfu host waits after
complete transfer of the new image for DFU_MANIFEST_POLL_TIMEOUT
ms before sending again an usb request. So the board have enough
time to erase rest of the nand sectors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
As Simon Glass requested it, here's a patch that enables
CONFIG_CMD_LZMADEC in sandbox.
Signed-off-by: Patrice Bouchand <pbfwdlist@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_LEON is already defined in
arch/sparc/cpu/{leon2,leon3}/config.mk.
Remove the redundant definition in board header files.
All leon3 boards define CONFIG_LEON3 in board header files.
Move the definition to arch/sparc/cpu/leon3/config.mk.
CONFIG_LEON2 can be move to arch/sparc/cpu/leon2/config.mk
as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Enable the Chrome OS EC emulation for sandbox along with LCD, sound
expanded GPIOs and a few other options to make this work correctly.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s code is in fact Samsung-specific, but there might be other
implementation. Move this code into its own file. This makes it slightly
more obviously how to adjust the code to support another SoC, when someone
takes this task on.
Also drop non-FDT support, since it isn't used on Exynos 5.
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current 4MB size is a little small for some tests, so increase it.
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
enabling CONFIG_MACB makes other locations in the stamp config file
enable network related commands (actually prevents disabling them)
enable USB ethernet support by activating generic support as well as
Asix and Moschip ethernet adapters
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Andreas Bießman <andreas.devel@googlemail.com>
enable support for the Moschip USB ethernet adapter for those boards
which previously had support for "all other" USB ethernet adapters
(that's Asix _and_ SMSC) enabled -- which applies to harmony, m53evk,
mx53loco, nitrogen6x, omap3_beagle
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
adjust the harmony and omap3_beagle board configs to make
their CONFIG_USB_ETHER_* items appear in alphabetical order
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Patch a7e36fc9 (mtd: nand: omap: remove unused #defines from common
omap_gpmc.h) removed some MTD related defines. Including
GPMC_NAND_ECC_LP_x8_LAYOUT. But this define is also needed for the
memory controller configuration (only the x8 defines are needed,
the x16 defines are the default). Without it the NAND subsystem is
not configured correctly and booting into U-Boot does not work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When using the am335x_evm_nor target one is generally expecting to be
used in an environment when you want to program the NOR and not a
"deployment" type target. In addition this only supports the Beaglebone
White with the memory cape and NOR module installed, which precludes the
presence of SPI flash. Drop SPI as we were getting close to the binary
limit in some cases and slightly over with other toolchains.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables to run Trats2 board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Trats board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Universal board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Origen board on device tree.
Uart, DRAM and MMC init functions are removed as their
generic replacements form the common board file are used.
The config file is modified to contain only board specific options.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds common dtsi file and config header for all
Exynos 4 based boards.
Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Allow the boot of a device tree mainline kernel by aligning the environment
variables with other FSL boards.
Tested NFS boot of a dt 3.14-rc5 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Gateworks Ventana is a product family based on the i.MX6. This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).
When compiling these two boards, a warning message is displayed:
time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
and should not be defined by platforms" [-Wcpp]
There are no board maintainers for them so this commit just
deletes them.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Add NAND SPL boot support with hardware PMECC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add SPI SPL boot support for sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
- NAND flash
- SD/MMC card
- Two USB hosts
- Ethernet (one GMAC, one EMAC)
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[reorder boards.cfg]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.
Please note that this hooks up slot1 (MCI1) for SD. Not both.
Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).
CONFIG_ATMEL_MCI_PORTB not tested.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
but on T104xRDB, on setting this , DDR instability is observed.
Board-level debugging is in progress.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.
T2080PCIe-RDB Feature Overview
------------------------------
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
- SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
- SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
- NOR: 128MB 16-bit NOR flash
- NAND: 512MB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 gold-finger
- One PCIe x4 connector
- One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a TF-card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0.
Fix EMI2 for t2080qds, which was caused by adding t2081qds.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.
CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.
We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.
By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)
Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.
It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding
#ifdef CONFIG_SPL_BUILD
# define CONFIG_USE_PRIVATE_LIBGCC
#endif
to include/configs/tegra-common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.
We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.
CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.
Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.
This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Enable required clocks for GPIO to fix a boot issue introduced by commit
f33b9bd398 (arm: omap3: Enable clocks for
peripherals only if they are used).
Without this patch the u-boot freezes after the following messages
OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
IGEPv2 + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
Diving into the issue, the sequence that produces the u-boot freezes is
setup_net_chip
|--> gpio_direction_out
|--> _set_gpio_dataout
|--> __raw_writel
To avoid this we just need enable the clocks for GPIOs that are used, but it
would be interesting implement a mechanism to protect these situations and
make sure that the clock is enabled when we request a GPIO.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This retrieves a PXE config file over the network, and executes it. This
allows an extlinux config file to be retrieved over the network and
executed, whereas the existing bootcmd_dhcp retrieves a U-Boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Update the common Tegra boot scripts in the default environment to
a) Make use of the new "test -e" shell command to avoid some error
messages.
b) Allow booting using the sysboot command and extlinux.conf. This
allows easy creation of boot menus, and provides a simple interface
for distros to parameterize/configure the boot process.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Modify all Tegra boards to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the Tegra files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's EHCI controllers only have a single PORTSC register. Configure
U-Boot to know this. This prevents e.g. ehci_shutdown() from touching
non-existent registers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.
To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.
The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Add some tests of driver model functionality. Coverage includes:
- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed
This function is enabled for sandbox, using CONFIG_DM_TEST.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE
option to make it easier to use device tree with sandbox.
This adjusts the Makefile to build a u-boot.dtb file which can be passed
to sandbox U-Boot with:
./u-boot -d u-boot.dtb
Signed-off-by: Simon Glass <sjg@chromium.org>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
Since the switch may be re-configured for VLAN usage in Linux (or any
other OS), lets reset the switch to its default register values upon
power-up. Otherwise network might not be available in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
