Simon Glass <sjg@chromium.org> says:
This series continues refactoring the bootm code to allow it to be used
with CONFIG_COMMAND disabled. The OS-handling code is refactored and
a new bootm_run() function is created to run through the bootm stages.
This completes the work.
A booti_go() function is created also, in case it proves useful, but at
last for now standard boot does not use this.
This is cmdd (part d of CMDLINE refactoring)
It depends on dm/bootstda-working
which depends on dm/cmdc-working
It is useful for sandbox to build as much code as possible. Enable
support for booting various other operating systems. Add the missing
cache functions.
These operating systems do not actually boot on sandbox, of course.
Signed-off-by: Simon Glass <sjg@chromium.org>
Disable CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY, this is not required nor used
on verdin am62, disable it to save precious binary size.
Update defconfig using savedefconfig, this adds CONFIG_OF_LIBFDT_OVERLAY
explicitly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This change configures Toradex Colibri iMX8X SoM USB
hub to bypass mode, and brings out of the reset state.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
-----BEGIN PGP SIGNATURE-----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=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
This adds support for the MT8365 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Sync Amlogic GXBB, GXL & GXM DTs from Linux v6.4, and also
switch to GXL MDIO MUX driver to adapt to DT change,
Most of the changes are only cosmetic or doesn't concern U-Boot,
the most important change for U-Boot is the GXL mdio mux compatible
switch to amlogic,gxl-mdio-mux.
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-2-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Migrate to the new environment format and drop most of the config.h.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on stm32f469-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support to Orise Tech OTM8009A display on stm32f469-disco board.
It was necessary to retrieve the framebuffer address from the device tree
because the address returned by the video-uclass driver pointed to a memory
area that was not usable.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add basic sandbox support for 'booti' so we can start to boot the test
ARMbian image. This is helpful in checking that it is parsed correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add fastboot support for Apalis iMX6, Colibri iMX6, Colibri iMX6ULL and
Colibri iMX7 boards. Remove CONFIG_FASTBOOT_BUF_SIZE from
colibri_imx7_emmc_defconfig to get the default value of 0x7000000 instead
of 0x10000000, to make it consistent with the other boards.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Auto-starting the WDT can cause false reboots when the user
is not intentionally trying to use the WDT, so leave it off until
it is requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
The hardware only supports a specific console port, so remove the
option to change the console location in the environment.
Signed-off-by: Adam Ford <aford173@gmail.com>
Auto-starting the WDT can cause false reboots when the user
is not intentionally trying to use the WDT, so leave it off until
it is requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
The hardware only supports a specific console port, so remove the
option to change the console location in the environment.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, building imx8qm_dmsse20a1_defconfig leads to the following
warning:
aarch64-linux-ld.bfd: invalid origin for memory region .sdram
Fix it by using the same SPL memory layout as done in the imx8mq_evk.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/93903a53ad9358ae69991558b787f574797effbe.1699619666.git.michal.simek@amd.com
Enable the initial kria SOM specific configurations like pinctrl,
pinconf etc. Also add the environment file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231109042407.6123-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Enable GETOPT so that 'bdinfo' command with getopt() support can be
tested in CI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Since commit b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
and commit e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Amlogic boards now requires DM_USB_GADGET to have USB Gadget to work.
Add it to the boards configs as returned by:
$ grep -L DM_USB_GADGET $(grep -l CONFIG_USB_GADGET $(grep -l MESON configs/*))
Fixes: b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
Fixes: e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Link: https://lore.kernel.org/r/20231206-u-boot-m2s-fix-usb-gadget-v1-1-1c4c66cd10f3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581 ("sunxi: H616: enable USB support for H616 boards")
Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To quote the author:
"Scmi" command will be re-introduced per Michal's request.
The functionality is the same as I put it in my patch set of adding
SCMI base protocol support, but made some tweak to make UT, "ut dm
scmi_cmd," more flexible and tolerable when enabling/disabling a specific
SCMI protocol for test purpose.
Each commit may have some change history inherited from the preceding
patch series.
Test
====
The patch series was tested on the following platforms:
* sandbox
In this test, "scmi" command is tested against different sub-commands.
Please note that scmi command is for debug purpose and is not intended
in production system.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
As correct default SYS_CONFIG_NAME value is now set in
board/samsung/axy17lte/Kconfig (in commit "board: samsung: Fix
SYS_CONFIG_NAME configs in axy17lte Kconfig"), the SYS_CONFIG_NAME
option can be safely removed from all a*y17lte defconfigs. That removal
doesn't change resulting .config files.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
None of these platforms enabled a networking devices, and disabled
CMD_NET. Given that we used to gate network support on CMD_NET rather
than NET, we disable CONFIG_NET on these platforms now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The initcall sequence fails at arch_misc_init. Disable misc init until
driver model and DT are clean.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
These targets use NAND FLASH only. Maybe some MMC definitions were added by
trying MMC for the etamin target evaluation and were not removed.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add am62x_beagleplay_* defconfig customized for the configuration of
BeaglePlay and drop the config fragments.
This is in preparation for dropping the dependency on ti vendor folder
entirely.
Signed-off-by: Nishanth Menon <nm@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
- squashfs improvements, remove common.h in some places, assorted code
fixes, fix a few CONFIG symbol names in Kconfig files, bring in
linux's <linux/time.h> conversion functions, poplar updates, bcb
improvements.
Set CONFIG_NET_RANDOM_ETHADDR=y, which sets random eth address in
case there is no configuration provided neither in CONFIG_ETHADDR
nor in "ethaddr" env variable.
This fixes the problem:
poplar# dhcp
Error: ethernet@9841000 address not set.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Several boards enable SPL_FS_FAT and SPL_LIBDISK_SUPPORT when they can't be
used (as there is no block device support enabled). Disable these configs.
The list of boards was generated with the following command:
$ tools/qconfig.py -f SPL SPL_FS_FAT ~SPL_MMC ~SPL_BLK_FS ~SPL_SATA \
~SPL_USB_STORAGE ~ENV_IS_IN_FAT ~EFI
LIBDISK was left enabled for the am* boards, since it seems to result in
actual size reduction, indicating that partitions are being used for
something.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
To quote the author:
This series tests raw nand flash in sandbox and fixes various bugs discovered in
the process. I've tried to do things in a contemporary manner, avoiding the
(numerous) variations present on only a few boards. The test is pretty minimal.
Future work could test the rest of the nand API as well as the MTD API.
Bloat (for v1) at [1] (for boards with SPL_NAND_SUPPORT enabled). Almost
everything grows by a few bytes due to nand_page_size. A few boards grow more,
mostly those using nand_spl_loaders.c. CI at [2].
[1] https://gist.github.com/Forty-Bot/9694f3401893c9e706ccc374922de6c2
[2] https://source.denx.de/u-boot/custodians/u-boot-clk/-/pipelines/18443
Add a SPL test for the NAND load method. We use some different functions to
do the writing from the main test since things like nand_write_skip_bad
aren't available in SPL.
We disable BBT scanning, since scan_bbt is only populated when not in SPL.
We use nand_spl_loaders.c as it seems to be common to at least a few boards
already. However, we do not use nand_spl_simple.c because it would require
us to implement cmd_ctrl. The various nand load functions are adapted from
omap_gpmc. However, they have been modified for simplicity/correctness.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add a sandbox NAND flash driver to facilitate testing. This driver supports
any number of devices, each using a single chip-select. The OOB data is
stored in-band, with the separation enforced through the API.
For now, create two devices to test with. The first is a very small device
with basic ECC. The second is an 8G device (chosen to be larger than 32
bits). It uses ONFI, with the values copied from the datasheet. It also
doesn't need too strong ECC, which speeds things up.
Although the nand subsystem determines the parameters of a chip based on
the ID, the driver itself requires devicetree properties for each
parameter. We do not derive parameters from the ID because parsing the ID
is non-trivial. We do not just use the parameters that the nand subsystem
has calculated since that is something we should be testing. An exception
is made for the ECC layout, since that is difficult to encode in the device
tree and is not a property of the device itself.
Despite using file I/O to access the backing data, we do not support using
external files. In my experience, these are unnecessary for testing since
tests can generally be written to write their expected data beforehand.
Additionally, we would need to store the "programmed" information somewhere
(complicating the format and the programming process) or try to detect
whether block are erased at runtime (degrading probe speeds).
Information about whether each page has been programmed is stored in an
in-memory buffer. To simplify the implementation, we only support a single
program per erase. While this is accurate for many larger flashes, some
smaller flashes (512 byte) support multiple programs and/or subpage
programs. Support for this could be added later as I believe some
filesystems expect this.
To test ECC, we support error-injection. Surprisingly, only ECC bytes in
the OOB area are protected, even though all bytes are equally susceptible
to error. Because of this, we take care to only corrupt ECC bytes.
Similarly, because ECC covers "steps" and not the whole page, we must take
care to corrupt data in the same way.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Rename SPL_MTD_SUPPORT to SPL_MTD in order to match MTD. This allows using
CONFIG_IS_ENABLED to test for MTD support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Contrary to what the help message says, this is the number of pages per
block. Calculate it automatically based on SYS_NAND_BLOCK_SIZE and
SYS_NAND_PAGE_SIZE. To better reflect its semantics, rename it to
SYS_NAND_BLOCK_PAGES.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
Now that Ringneck requires some board-specific code (namely resetting
the MCU companion controller) to be run during SPL stage, let's enable
SPL_BOARD_INIT.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is
0x160000 . Define this size in U-Boot config to prevent misconfigured
builds from emitting larger u-boot.itb than the one which fits the
SPI NOR area reserved for the blob.
The SPI NOR layout is as follows:
0x00_0000..0x03_ffff ... SPL 1
0x04_0000..0x07_ffff ... SPL 2
0x08_0000..0x1d_ffff ... U-Boot
0x1e_0000..0x1e_ffff ... Environment 1
0x1f_0000..0x1f_ffff ... Environment 2
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This is a useful tool to check the presence of a device on a specific
i2c bus, so let's enable it.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not used for sandbox, so drop it. Enable the things that it
controls to avoid dstrastic changes in the config settings for
sandbox builds.
The end result is that these are enabled:
BOOTMETH_DISTRO
BOOTSTD_DEFAULTS
and these are disabled:
USE_BOOTCOMMAND
BOOTCOMMAND (was "run distro_bootcmd")
DISTRO_DEFAULTS
Note that the tools-only build has already disabled DISTRO_DEFAULTS
and BOOTSTD_FULL
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
