Commit graph

893 commits

Author SHA1 Message Date
Albert ARIBAUD
4b19b7448e Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.

Conflicts:
	board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08 21:20:49 +02:00
Eric Nelson
e2140588dd usb: gadget: fastboot: terminate commands with NULL
Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.

Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 21:07:44 +02:00
Daniel Mack
16b61d13ba usb: musb-new: core: set MUSB_POWER_HSENAB in MUSB_POWER for host mode
This bit allows the MUSB controller to negotiate for high-speed mode when
the device is reset by the hub. If unset, Babble errors occur with
high-speed mass storage devices right after the first packet. This condition
is not caught by the interrupt handles in U-Boot, so no recovery is done,
and the USB communication is stuck.

To fix this, set the bit unconditionally, not only for
CONFIG_USB_GADGET_DUALSPEED but also for host-only modes.

Signed-off-by: Daniel Mack <zonque@gmail.com>
2014-10-06 21:04:44 +02:00
Marcel Ziswiler
d1fcbae117 usb: tegra: ULPI regression on tegra20
Trying to enumerate USB devices connected via ULPI to T20 failed as
follows:

USB2:   ULPI integrity check failed

Git bisecting revealed the following commit being at odds:

commit 2d34151f75
usb: tegra: refactor PHY type selection

Looking at above commit one quickly identifies a copy paste error which
this patch fixes. Happy ULPIing again (;-p).

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-06 16:12:48 +02:00
Eric Nelson
84c24f66c2 usb: gadget: fastboot: explicitly set radix of maximum download size
The processing of the max-download-size variable requires a
radix specifier, or the fastboot host tool will interpret
it as an octal number.

See function get_target_sparse_limit() in file fastboot/fastboot.c
in the AOSP:
        https://android.googlesource.com/platform/system/core/+/master

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 14:50:44 +02:00
Eric Nelson
c674a6660e usb: gadget: fastboot: add max-download-size variable
Current Android Fastboot seems to use 'max-download-size' instead
of 'downloadsize' variable to indicate the maximum size of sparse
segments.

See function get_target_sparse_limit() in file fastboot/fastboot.c
in the AOSP:
	 https://android.googlesource.com/platform/system/core/+/master

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 14:50:44 +02:00
Eric Nelson
e206799370 usb: ci_udc: respect CONFIG_USB_GADGET_DUALSPEED
Force full-speed (12 Mbit/s) operation if CONFIG_USB_GADGET_DUALSPEED
is not defined.

The controller is capable of high-speed (480 Mbit/s) operation,
but some designs may require the use of lower-speed operation.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 14:50:44 +02:00
Bo Shen
23d1d10c42 usb: gadget: fastboot: improve download progress bar
When download is ongoing, if the actual size of one transfer
is not the same as BYTES_PER_DOT, which will cause the dot
won't print anymore. Then it will let the user thinking it
is stuck, actually it is transfering without dot printed.

So, improve the method to show the progress bar (print dot).

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-10-06 14:50:43 +02:00
Eric Nelson
f9935c87b6 usb: f_mass_storage: set removable flag in do_inquiry based on LUN
Without this flag, tools like Alex Page's USB Image Tool
won't see drives exposed over USB Gadget as removable,
and won't allow access to them.
	http://www.alexpage.de/usb-image-tool/

The code was pulled from the main-line kernel:
	drivers/usb/gadget/function/f_mass_storage.c

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 14:50:43 +02:00
Heiko Schocher
9f3b8ed14c usb: dfu: add fullspeed support for DFU
DFU now can use also fullspeed.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Liu Bin <b-liu@ti.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
2014-10-06 14:50:43 +02:00
Lukasz Majewski
b9c99d3246 usb: dfu: thor: gadget: Remove dead code
This code is not used anymore in the current DFU implementation and
can be safely removed.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2014-10-06 14:50:43 +02:00
Hans de Goede
36b73109c4 usb: ehci: Make periodic_schedules a per controller variable
Periodic schedules tracks how many int_queue-s are active, and decides whether
or not to en/disable the periodic schedule based on this. This is clearly
a per controller thing.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-06 14:50:42 +02:00
Hans de Goede
415548d884 usb: ehci: poll_int_queue check real qtd, not the overlay
When we first start an int queue, the qh's overlay area is all zeros. This
gets filled by the hc with the actual qtd values as soon as it advances
the queue, but we may call poll_int_queue before then, in which case we
would think the transfer has completed as the hc has not yet copied the
qt_token to the overlay, so the active flag is not set.

This fixes this by checking the actual qtd token, rather then the overlay.
This also fixes a (theoretical) race where we see the completion in the
overlay and free and re-use the qtd before the hc has completed writing back
the overlay to the actual qtd.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-06 14:50:42 +02:00
Hans de Goede
ea7b30c589 usb: ehci: Add missing cache flush to destroy_int_queue
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-06 14:50:42 +02:00
Hans de Goede
4e2c4ad360 usb: ehci: Properly set hub devnum and portnr with usb-1 hubs in the chain
For full / low speed devices we need to get the devnum and portnr of the tt,
so of the first upstream usb-2 hub, not of the parent device (which may be a
usb-1 hub).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-06 14:50:42 +02:00
Ye.Li
5546ad0734 usb: ehci-mx6: Rename the USB register base address
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.

This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29 10:33:27 +02:00
Marek Vasut
dd24b57bb7 usb: ehci: mxs: Add board-specific callbacks
Add board-specific callbacks for enabling/disabling port power
into the MXS EHCI controller driver. This is in-line with the
names of callbacks on other systems.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Masahiro Yamada
ed36323f6d kconfig: add blank Kconfig files
This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00
Steve Rae
593cbd93f3 usb/gadget: fastboot: minor cleanup
- update static function
- additional debugging statements
- update "fastboot command" information
- add missing include file
- update spelling

Signed-off-by: Steve Rae <srae@broadcom.com>
2014-09-24 18:30:27 -04:00
Steve Rae
d1b5ed0753 usb/gadget: fastboot: add support for flash command
- implement 'fastboot flash' for eMMC devices

Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2014-09-24 18:30:27 -04:00
Bo Shen
97b2043da6 USB: ehci-atmel: use pcr to enable or disable clock
If the SoC has pcr, we use pcr (peripheral control register)
to enable or disable clock.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:21 +02:00
Bo Shen
01c8bf5a6f USB: ohci-at91: use pcr to enable or disable clock
If the SoC has pcr, we use pcr (peripheral control register)
to enable or disable clock.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:20 +02:00
Simon Glass
ad6e48e509 net: usb: Add SMSC copyright to smsc95xx driver
This driver was upstreamed without an SMSC copyright, even thought it seems
that SMSC was the original author.

See the kernel version for a code comparison:

http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=2f7ca802bdae2ca41022618391c70c2876d92190

It's not clear who actually moved this code, or whether the kernel was the
original source, or somewhere else, but it probably should still have the
SMSC copyright.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-16 12:23:59 -04:00
Masahiro Yamada
3b61297024 kbuild: force to define __UBOOT__ in all the C sources
U-Boot has imported various source files from other projects,
mostly Linux.

Something like

  #ifdef __UBOOT__
    [ modification for U-Boot ]
  #else
    [ original code ]
  #endif

is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.

Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2014-09-16 12:23:56 -04:00
Bo Shen
06fa91cd67 USB: gadget: s3c: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2014-09-02 14:32:15 +02:00
Bo Shen
f9abd4b415 USB: gadget: atmel: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2014-09-02 14:32:15 +02:00
Stephen Warren
842ef9a98e usb: ci_udc: implement dfu_usb_get_reset
This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-09-02 14:29:28 +02:00
Lukasz Majewski
f2ec4e34aa udc: dfu: s3c_udc: Provide function to check if USB reset was asserted
New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.

Without this function the previous DFU behavior is preserved.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2014-09-02 14:29:28 +02:00
Lukasz Majewski
1cc03c5c53 dfu: Provide means to find difference between dfu-util -e and -R
This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.

By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.

Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.

It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.

Example usage:
1. -e (detach) switch
 dfu-util -a0 -D file1.bin;dfu-util -a3 -D uImage;dfu-util -e

 access to u-boot prompt.

2. -R (reset) switch
 dfu-util -a0 -D file1.bin;dfu-util -R -a3 -D uImage

 target board reset

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2014-09-02 14:29:28 +02:00
Tom Rini
3e1b36bd58 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-28 13:03:25 -04:00
Heiko Schocher
0c06db5983 lib, linux: move linux specific defines to linux/compat.h
- move linux specific defines from usb and video code
  into linux/compat.h
- move common linux specific defines from include/ubi_uboot.h
  to linux/compat.h
- add for new mtd/ubi/ubifs sync new needed linux specific
  defines to linux/compat.h

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[trini: Add spin_lock_irqsave/spin_unlock_irqrestore dummies from
usb/lin_gadet_compat.h]
Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25 19:25:03 -04:00
Masahiro Yamada
62d636aa2a omap: remove omap5912osk board support
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.

Tom suggested to remove this board.

Remove also omap1510_udc.c because this is the last board
to enable it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
8ac22a60e2 omap: clean-up dead configs
The following configs are not defined at all.

 - CONFIG_OMAP1510
 - CONFIG_OMAP_1510P1
 - CONFIG_OMAP_SX1
 - CONFIG_OMAP3_DMA
 - CONFIG_OMAP3_ZOOM2
 - CONFIG_OMAP_INNOVATOR

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2014-08-09 11:17:04 -04:00
Nobuhiro Iwamatsu
5906fadefa usb: ehci: rmobile: Remove xHCI address
echi-rmobile does not support xHCI. This removes xHCI address
from address table. And this revise a value of CONFIG_USB_MAX_CONTROLLER_COUNT
for lager board and koelsh board.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-08-09 11:17:01 -04:00
Nobuhiro Iwamatsu
ed7ce836cd usb: ehci: rmobile: Add support R8A7794
R8A7794 has same IP of USB controller as R8A7790 and R8A7791.
This addes support for R8A7794.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-08-09 11:17:01 -04:00
Stephen Warren
7ac1b410ac dfu: allow backend to specify a maximum buffer size
CONFIG_SYS_DFU_DATA_BUF_SIZE may be large to allow for FAT/ext layouts
to transfer large files. However, this means that individual write
operations will take a long time. Allow backends to specify a maximum
buffer size, so that each write operation is limited to a smaller data
block. This prevents the DFU protocol from timing out when e.g. writing
to SPI flash. I would guess that NAND might benefit from setting this
value too, but I can't test that.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-08-09 11:16:58 -04:00
Stephen Warren
3ee9593fce dfu: add write error handling
Fix calls to dfu_write() and dfu_flush() to detect errors in the I/O
itself. This could happen due to problems with the storage medium, or
simply when trying to write a FAT/ext file that is larger than the buffer
dfu_mmc.c maintains for this purpose.

Signal the error by switching the DFU state/status. This will be picked
up by the DFU client when it sends the next DFU request. Note that errors
can't simply be returned from e.g. dnload_request_complete(), since that
function has no way to pass errors back to the DFU client; a call to
dnload_request_complete() simply means that a USB OUT completed.

This error state/status needs to be cleared when the next DFU client
connects. While there is a DFU_CLRSTATUS request, no DFU client seems to
send this. Hence, clear this when selecting the USB alternate setting on
the USB interface.

Finally, dfu.c relies on a call to dfu_flush() to clear up the internal
state of the write transaction. Now that errors in dfu_write() are
detected, dfu_flush() may no longer be called for every transaction.
Separate out the cleanup code into a new function, and call it whenever
dfu_write() fails, as well as from any call to dfu_flush().

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-08-09 11:16:58 -04:00
Roman Byshko
8d154002f3 sunxi: add USB EHCI driver
The Allwinner aka sunxi SoCs have one or more USB host controllers.
This adds a driver for their EHCI.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Lijun Pan
4a755f1da5 driver/usb: include upper/lower_32_bits() from linux/compat.h
upper_32_bits() and lower_32_bits() have been ported into linux/compat.h.
Start use them now in drivers/usb/host/xhci.h.

Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
2014-07-22 07:44:24 -04:00
Felipe Balbi
5ba95541b7 usb: phy: omap_usb_phy: implement usb_phy_power() for AM437x
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09 22:11:51 +02:00
Felipe Balbi
26707d9e6b usb: host: xhci: make sure to power up PHY
some boards won't work if the PHY isn't explicitly
powered up.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09 22:11:51 +02:00
Sergey Kostanbaev
7237d22baa arm: ep9315: Return back Cirrus Logic EDB9315A board support
This patch returns back support for old ep93xx processors family

Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
2014-07-04 23:45:48 +02:00
Stephen Warren
dcb89b5aa0 usb: ci_udc: use var name ep/ci_ep consistently
Almost all of ci_udc.c uses variable name "ep" for a struct usb_ep and
"ci_ep" for a struct ci_ep. This is nice and consistent, and helps people
know what type a variable is without searching for the declaration.
handle_ep_complete() doesn't do this, so fix it to be consistent.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
369d3c439a USB: gadget: atmel: zero out allocated requests
A UDC's alloc_request method should zero out the newly allocated request.
Ensure the Atmel driver does so. This issue was found by code inspection,
following the investigation of an intermittent issue with ci_udc, which
was tracked down to failing to zero out allocated requests following some
of my changes. All other UDC drivers already zero out requests in one
way or another.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
639e9903c2 usb: ci_udc: don't memalign() struct ci_req allocations
struct ci_req is a purely software structure, and needs no specific
memory alignment. Hence, allocate it with calloc() rather than
memalign(). The use of memalign() was left-over from when struct ci_req
was going to hold the aligned bounce buffer, but this is now dynamically
allocated.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
6ac15fda4e usb: ci_udc: remove controller.items array
There's no need to store an array of QTD pointers in the controller.
Since the calculation is so simple, just have ci_get_qtd() perform it
at run-time, rather than pre-calculating everything.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
7e54188775 usb: ci_udc: fix items array size/stride calculation
2 QTDs are allocated for each EP. The current allocation scheme aligns
the first QTD in each pair, but simply adds the struct size to calculate
the second QTD's address. This will result in a non-cache-aligned
addresss IF the system's ARCH_DMA_MINALIGN is not 32 bytes (i.e. the
size of struct ept_queue_item).

Similarly, the original ilist_ent_sz calculation aligned the value to
ARCH_DMA_MINALIGN but didn't take the USB HW's 32-byte alignment
requirement into account. This doesn't cause a practical issue unless
ARCH_DMA_MINALIGN < 32 (which I suspect is quite unlikely), but we may
as well fix the code to be explicit, so it's obviously completely
correct.

The new value of ILIST_ENT_SZ takes all alignment requirements into
account, so we can simplify ci_{flush,invalidate}_qtd() by simply using
that macro rather than calling roundup().

Similarly, the calculation of controller.items[i] can be simplified,
since each QTD is evenly spaced at its individual alignment requirement,
rather than each pair being aligned, and entries within the pair being
spaced apart only by structure size.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
06b38fcbae usb: ci_udc: lift ilist size calculations to global scope
This will allow functions other than ci_udc_probe() to make use of the
constants in a future change.

This in turn requires converting the const int variables to #defines,
since the initialization of one global const int can't depend on the
value of another const int; the compiler thinks it's non-constant if
that dependency exists.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
8d7c39d3e8 usb: ci_udc: don't assume QTDs are adjacent when transmitting ZLPs
Fix ci_ep_submit_next_request()'s ZLP transmission code to explicitly
call ci_get_qtd() to find the address of the other QTD to use. This
will allow us to correctly align each QTD individually in the future,
which may involve leaving a gap between the QTDs.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Stephen Warren
d7beeb9358 usb: ci_udc: fix ci_flush_{qh,qtd} calls in ci_udc_probe()
ci_udc_probe() initializes a pair of QHs and QTDs for each EP. After
each pair has been initialized, the pair is cache-flushed. The
conversion from QH/QTD index [0..2*NUM_END_POINTS) to EP index
[0..NUM_ENDPOINTS] is incorrect; it simply subtracts 1 (which yields
the QH/QTD index of the first entry in the pair) rather than dividing
by two (which scales the range). Fix this.

On my system, this avoids cache debug prints due to requests to flush
unaligned ranges. This is caused because the flush calls happen before
the items[] array entries are initialized for all but EP0.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-07-02 15:45:38 +02:00
Ilya Ledvich
08ebd467c8 usb: eth: smsc95xx: add LAN9500A device ID
Add LAN9500A product ID (0x9e00) in order to support LAN9500A based dongles.
Tested on cm_t335.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
2014-06-25 22:46:28 +02:00
Jeroen Hofstee
29425be49b usb: fastboot: fix potential buffer overflow
cb_getvar tries to prevent overflowing the response buffer
by using strncat. But strncat takes the number of data bytes
copied as a limit not the total buffer length so it can still
overflow. Pass the correct value instead.

cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
cc: Rob Herring <robh@kernel.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-25 22:44:40 +02:00
Jeroen Hofstee
25d1936a19 usb: xhci: (likely) fix bracket in if condition
Because of the brackets the & and && is evaluated before
the comparison. This is likely not the intention. Change
it to test the first and second condition to both be true.

cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-25 22:43:16 +02:00
Jeroen Hofstee
19a2a67fa2 usb:g_dnl:f_thor: remove memset before memcpy
since ALLOC_CACHE_ALIGN_BUFFER defines a pointer and not a
buffer, the memset with sizeof(rqt) likely does something else
then intended. Since there is a memcpy directly after it with
the full size, drop the memset completely.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-06-25 22:42:40 +02:00
Jeroen Hofstee
933611f7bb usb:composite: clear the whole common buffer
Since the struct fsg_common is calloced, reset it completely
with zero's when reused. While at it, make checkpatch happy.

cc: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-06-25 22:42:07 +02:00
Yasuhisa Umano
198c5f998a usb: r8a66597: Fix initilization size of r8a66597 info structure
Initialization of r8a66597 info structure is not enough.
Because initilization was used size of pointer.
This fixes that use size of r8a6659 info structure.

Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
2014-06-25 22:38:04 +02:00
yasuhisa umano
8ecdce7280 usb: r8a66597: Fix initialization hub that using R8A66597_MAX_ROOT_HUB
This driver is processed as two USB hub despite one.
The number of root hub is defined in R8A66597_MAX_ROOT_HUB.
This fixes that register is accessed by using the definition
of R8A66597_MAX_ROOT_HUB.

Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
2014-06-25 22:31:41 +02:00
Jeroen Hofstee
51afc2c68c usb: cosmetic: double const
For plain array const can be either before or after
the type definition. Adding both is simply redundand.
Remove the later one.

cc: marex@denx.de
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-25 22:22:20 +02:00
Stephen Warren
83c3750088 usb: ci_udc: fix typo in debug message
s/ot/to/

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-25 22:22:20 +02:00
Stephen Warren
fb22ae6c7e usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC
ci_udc.c's usb_gadget_unregister_driver() doesn't call driver->unbind()
unlike other USB gadget drivers. Fix it to do this.

Without this, when ether.c's CDC Ethernet device is torn down,
eth_unbind() is never called, so dev->gadget is never set to NULL.
For some reason, usb_eth_halt() is called both at the end of the first
use of the Ethernet device, and prior to any subsequent use. Since
dev->gadget is never cleared, all calls to usb_eth_halt() attempt to
stop, disconnect, and clean up the device, resulting in double cleanup,
which hangs U-Boot on my Tegra device at least.

ci_udc allocates its own singleton EP0 request object, and cleans it up
during usb_gadget_unregister_driver(). This appears necessary when using
the USB gadget framework in U-Boot, since that does not allocate/free
the EP0 request. However, the CDC Ethernet driver *does* allocate and
free its own EP0 requests. Consequently, we must protect
ci_ep_free_request() against double-freeing the request.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-25 22:22:20 +02:00
Stephen Warren
e0672b3c3a usb: ci_udc: terminate ep0 INs with a zlp when required
Sometimes, a zero-length packet is required at the end of an IN
transaction so that the host knows the device is done sending data.
Enhance ci_udc to send a zlp when necessary. See the comments for
more details.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-11 02:26:05 +02:00
Stephen Warren
b7c0051687 usb: ci_udc: clean up all allocations in unregister
usb_gadget_unregister_driver() is called to tear down the USB device mode
stack. Fix the driver to stop the USB HW (which causes any attached host
to notice the disappearance of the device), and free all allocations
(which obviously prevents memory leaks).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-11 02:26:05 +02:00
Stephen Warren
9a7d34be13 usb: ci_udc: fix probe error cleanup
If allocation of the ep0 req fails, clean up all the allocations that
were made in ci_udc_probe().

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-11 02:26:05 +02:00
Stephen Warren
bdf81611e4 usb: ci_udc: fix freeing of ep0 req
ci_ep_alloc_request() avoids allocating multiple request objects for ep0
by keeping a record of the first req allocated for ep0, and always
returning that instead of allocating a new req. However, if this req is
ever freed, the record of the previous allocation is not cleared, so
ci_ep_alloc_request() will keep returning this stale pointer. Fix
ci_ep_free_request() to clear the record of the previous allocation.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-11 02:26:05 +02:00
Stephen Warren
43a8f25b6c usb: ci_udc: call udc_disconnect() from ci_pullup()
ci_pullup()'s !is_on path contains a cut/paste copy of udc_disconnect().
Remove the duplication by simply calling udc_disconnect() instead.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-11 02:26:05 +02:00
Stephen Warren
006c702688 usb: ci_udc: complete ep0 direction handling
handle_setup() currently assumes that the response to a Setup transaction
will be an OUT transaction, and any subsequent packet (if any) will be an
IN transaction. This appears to be valid in many cases; both USB
enumeration and Mass Storage work OK with this restriction. However, DFU
uses ep0 to transfer data in both directions. This renders the assumption
invalid; when sending data from device to host, the Data Stage is an IN
transaction, and the Status Stage is an OUT transaction. Enhance
handle_setup() to deduce the correct direction for the USB transactions
based on Setup transaction data.

ep0's request object only needs to be automatically re-queued when the
Data Stage completes, in order to implement the Status Stage. Once the
Status Stage transaction is complete, there is no need to re-queue the
USB request, so don't do that.

Don't sent USB request completion callbacks for Status Stage transactions.
These were queued by ci_udc itself, and only serve to confuse the USB
function code. For example, f_dfu attempts to interpret the 0-length data
buffers for Status Stage transactions as DFU packets. These buffers
contain stale data from the previous transaction. This causes f_dfu to
complain about a sequence number mismatch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-01 19:22:40 +02:00
Stephen Warren
a2d8f92985 usb: ci_udc: pre-allocate ep0 req
Allocate ep0's USB request object when the UDC driver is probed. This
solves a couple of issues in the current code:

a) A request object always exists for ep0. Prior to this patch, if setup
transactions arrived in an unexpected order, handle_setup() would need
to reply to a setup transaction before any ep0 usb_req was created.

This issue was introduced in commit 2813006fec "usb: ci_udc: allow
multiple buffer allocs per ep."

b) handle_ep_complete no longer /has/ to queue the ep0 request again
after every single request completion. This is currently required, since
handle_setup() assumes it can find some request object in ep0's request
queue. This patch doesn't actually stop handle_ep_complete() from always
requeueing the request, but the next patch will.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-01 19:22:40 +02:00
Stephen Warren
054731b09e usb: ci_udc: use a single descriptor for ep0
ci_udc currently points ep->desc at separate descriptors for IN and OUT.
These descriptors only differ in the ep address IN/OUT field. Modify the
code to use a single descriptor, and change that descriptor's ep address
to indicate IN/OUT as required. This removes some data duplication.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-01 19:22:40 +02:00
Stephen Warren
7484d84cbb usb: ci_udc: detect queued requests on ep0
The flipping of ep0 between IN and OUT relies on ci_ep_queue() consuming
the current IN/OUT setting immediately. If this is deferred to a later
point when the req is pulled out of ci_req->queue, then the IN/OUT
setting may have been changed since the req was queued, and state will
get out of sync. This condition doesn't occur today, but could if bugs
were introduced later, and this error-check will save a lot of debugging
time.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-01 19:22:39 +02:00
Albert ARIBAUD
c534d2fdcf Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-05-23 22:50:23 +02:00
Tom Rini
8e38128596 Merge branch 'pr-15052014' of git://git.denx.de/u-boot-usb 2014-05-22 13:42:26 -04:00
Tom Rini
c9afa7cea8 Merge branch 'master' of git://git.denx.de/u-boot-usb 2014-05-22 12:56:15 -04:00
Nikhil Badola
15231f6dd1 drivers/usb : Define usb control register mask for w1c bits
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:27 -05:00
Przemyslaw Marczak
584b55b072 usb:gadget:f_thor: download_tail(): remove dfu_write with 0 size
Since dfu_flush() can write raw data, dfu_write() with zero size
can be removed from download_tail() in thor gadget.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
2014-05-15 00:23:56 +02:00
Stephen Warren
8630c1c7e3 usb: ci_udc: parse QTD before over-writing it
ci_udc only allocates a single QTD structure per EP. All data needs to be
extracted from the DTD prior to calling ci_ep_submit_next_request(), since
that fills the QTD with next transaction's parameters. Fix
handle_ep_complete() to extract the transaction (remaining) length before
kicking off the next transaction.

In practice, this only causes writes to UMS devices to fail for me. I may
have tested the final versions of my previous ci_udc patch only with
reads. More recently, I had patches applied locally that allocated a QTD
per USB request rather than per USB EP, although since that doesn't give
any performance benefit, I'm dropping those.

Fixes: 2813006fec ("usb: ci_udc: allow multiple buffer allocs per ep")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-15 00:21:30 +02:00
Stephen Warren
a4539a2aa7 usb: tegra: support device mode
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.

Detailed changes are:

* Rename set_host_mode() to set_up_vbus() since that's really what it
  does.

* Modify set_up_vbus() to know whether it's initializing in host or
  device mode, and:

  - Skip the external VBUS check in device mode, since external VBUS is
    expected in this case.

  - Disable VBUS output in device mode.

* Modify init_phy_mux() to know whether it's initializing in host or
  device mode, and hence skip setting USBMODE_CM_HC (which enables host
  mode) in device mode. See the comments in that function for why this
  is safe w.r.t. the ordering requirements of PHY selection.

* Modify init_utmi_usb_controller() to force "b session valid" in device
  mode, since the HW requires this. This is done in UTMI-specific code,
  since we only support device mode on the first USB controller, and that
  controller can only talk to a UTMI PHY.

* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
  vs. the dr_mode (dual-role mode) value present in device tree, and the
  HW configurations which support device mode.

* Enhance ehci_hcd_init() not to skip HW initialization when switching
  between host and device mode on a controller. This requires remembering
  which mode the last initialization used.

Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-15 00:21:17 +02:00
Stephen Warren
2d34151f75 usb: tegra: refactor PHY type selection
Both init_{utmi,ulpi}_usb_controller() have nearly identical code for
PHY type selection. Pull this out into a common function to remove the
duplication.

Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-15 00:21:17 +02:00
Stephen Warren
9b20fe6f1a usb: tegra: fix PHY selection code
The TRM for Tegra30 and later all state that USBMODE_CM_HC must be set
before writing to hostpc1_devlc to select which PHY to use for a USB
controller. However, neither init_{utmi,ulpi}_usb_controller() do this
today, so the register writes they perform for PHY selection do not
work.

For the UTMI case, this was hacked around in commit 7e44d9320e "ARM:
Tegra: USB: EHCI: Add support for Tegra30/Tegra114" by adding code to
ehci_hcd_init() which sets USBMODE_CM_HC and duplicates the PHY
selection register write. This code doesn't cover the ULPI case, so I
wouldn't be surprised if ULPI doesn't work with the current code, unless
the ordering requirement only ends up being an issue in HW for UTMI not
ULPI.

This patch fixes init_{utmi,ulpi}_usb_controller() to correctly set
USBMODE_CM_HC before selecting the PHY. Now that this works, we can
remove the duplicate UTMI-specific code in ehci_hcd_init(), thus
simplifying that function.

Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-15 00:21:17 +02:00
Marek Vasut
4180b3dba2 Merge remote-tracking branch 'u-boot/master' into test 2014-05-15 00:20:54 +02:00
Michal Simek
eb8c54bfaa ARM: zynq: ehci: Added USB host driver support
Added USB host driver for zynq.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Heiko Schocher
fc25fa27e5 dfu, nand: add medium specific polltimeout function
add a possibility to add a medium specific polltimeout
function. So it is possible to define different
poll timeouts.

Used on nand medium, for setting the DFU_MANIFEST_POLL_TIMEOUT
only on nand ubi partitions, which is currently the only
usecase.

Change-Id: If1db5f49b32d93fefa7481e8dfe5b7ccc0e65af4
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-08 10:38:30 +02:00
Heiko Schocher
ab2f5c12f7 musb-new, dfu: first send request answer then call completions
comment in ep0_txstate() states:

"report completions as soon as the fifo's loaded; there's no win
 in waiting till this last packet gets acked".

This is wrong for using dfu. In the dfu usecase we must send
a PollTimeout to the host, so the host can wait until the
U-Boot Code is ready for answering new usb requests. So the
answer which contains the PollTimeout must send *before*
U-Boot calls req->complete.

The req->complete is used in the dfu case for flushing the
medium, when entering DFU_STATE_dfuMANIFEST_SYNC state.

Change-Id: Ib2941119c72761e48e15fedbdad1ecce07ae0b3d
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-08 10:38:30 +02:00
Sebastian Siewior
3aab70afc5 usb/gadget: add the fastboot gadget
This patch contains an implementation of the fastboot protocol on the
device side and documentation. This is based on USB download gadget
infrastructure. The fastboot function implements the getvar, reboot,
download and reboot commands. What is missing is the flash handling i.e.
writting the image to media.

v3 (Rob Herring):
This is based on http://patchwork.ozlabs.org/patch/126798/ with the
following changes:
- Rebase to current mainline and updates for current gadget API
- Use SPDX identifiers for licenses
- Traced the history and added missing copyright to cmd_fastboot.c
- Use load_addr/load_size for transfer buffer
- Allow vendor strings to be optional
- Set vendor/product ID from config defines
- Allow Ctrl-C to exit fastboot mode
v4:
- Major re-write to use the USB download gadget. Consolidated function
code to a single file.
- Moved globals into single struct.
- Use puts and putc as appropriate.
- Added CONFIG_USB_FASTBOOT_BUF_ADDR and CONFIG_USB_FASTBOOT_BUF_SIZE to
set the fastboot transfer buffer.
v5:
- Add CONFIG option documentation to README
- Rebase using new downloader registration

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-08 10:38:30 +02:00
Stephen Warren
340ed422d2 usb: ums: remove ci_udc special case
Now that the ci_udc driver supports allocating multiple requests per
endpoint, we can revert the special-case added by a022c1e13c "usb:
ums: use only 1 buffer for CI_UDC".

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-07 23:36:58 +02:00
Stephen Warren
2813006fec usb: ci_udc: allow multiple buffer allocs per ep
Modify ci_ep_alloc_request() to return a dynamically allocated request
object, rather than a singleton that's part of the endpoint. This
requires moving various state from the endpoint structure to the request
structure, since we need one copy per request.

The "fast bounce buffer" b_fast is removed by this change rather than
moved to the request object. Instead, we enhance the bounce buffer logic
in ci_bounce()/ci_debounce() to keep the bounce buffer around between
request submissions. This avoids the need to allocate an arbitrarily-
sized bounce buffer up-front, yet avoids incurring the allocation
overhead each time a request is submitted.

A future enhancement would be to actually submit multiple requests to HW
at once. The Linux driver shows that this is possible. That might improve
throughput (depending on the USB protocol in use), since USB could be
performing a transfer to one HW buffer in parallel with whatever SW
actions U-Boot performs on another buffer. However, I have not made this
change as part of this patch, in order to keep SW changes related to
buffer management separate from any change in the way the HW is
programmed.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-07 23:36:58 +02:00
Stephen Warren
25fbf96b24 USB: gadget: save driver name before registering it
g_dnl_register() currently first attempts to register a composite
driver by name, and then saves the driver name once it's registered.
Internally to the registration code, g_dnl_do_config() is called and
attempts to compare the composite device's name with the list of known
device names. This fails since the composite device's name has not yet
been stored. This means that the first time "ums 0 0" is run, it fails,
but subsequent attempts succeed.

Re-order the name-saving and registration code to solve this.

Fixes: e5b834e07f51 ("USB: gadget: added a saner gadget downloader registration API")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-05 08:33:13 +02:00
Mateusz Zalega
c4d0e85604 USB: gadget: added a saner gadget downloader registration API
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-05-05 08:21:47 +02:00
Mateusz Zalega
75504e9592 usb: dfu: fix boards wo USB cable detection
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.

I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.

Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.

Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.

CONFIG_USB_CABLE_CHECK was removed.

Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-05 08:00:28 +02:00
Stephen Warren
2fc5dab2ed usb: gadget: allow ci_udc to build with new gadget framework
Allow ci_udc.o to be built when using the new(?) USB gadget framework,
as enabled by CONFIG_USB_GADGET.

Note that this duplicates the Makefile entry for ci_udc.o, since it's
also included inside #ifdef CONFIG_USB_ETHER. I'm not sure what that
define means; perhaps an old style of Ethernet-specific USB gadget
implementation?

I wonder if the line that this patch adds shouldn't be outside all of
the ifdefs, so it stands on its own, similar to how e.g. epautoconf.o
is shared between the two?

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-01 12:44:24 +02:00
Stephen Warren
a022c1e13c usb: ums: use only 1 buffer for CI_UDC
ci_udc.c allocates only a single buffer for each endpoint, which
ci_ep_alloc_request() returns as a hard-coded value rather than
dynamically allocating. Consequently, storage_common.c must limit
itself to using a single buffer at a time. Add a special case
to the definition of FSG_NUM_BUFFERS for this.

Another option would be to fix ci_ep_alloc_request() to dynamically
allocate the buffers like some/all(?) other device mode drivers do.
However, I don't think that ci_ep_queue() supports queueing up
multiple buffers either yet, and I'm not familiar enough with the
controller yet to implement that. As such, any attempt to use multiple
buffers simply results in data corruption and other errors.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-04-30 10:30:58 +02:00
Stephen Warren
fcf2ede190 usb: ci_udc: support variants with hostpc register
Tegra's USB controller appears to be a variant of the ChipIdea
controller; perhaps derived from it, or simply a different version of
the IP core to what U-Boot supports today.

In this variant, at least the following difference are present:
- Some registers are moved about.
- Setup transaction completion is reported in a separate 'epsetupstat'
  register, rather than in 'epstat' (which still exists, perhaps for
  other transaction types).
- USB connection speed is reported in a separate 'hostpc1_devlc'
  register, rather than 'portsc'.
- The registers used by ci_udc.c begin at offset 0x130 from the USB
  register base, rather than offset 0x140. However, this is handled
  by the associated EHCI controller driver, since the register address
  is stored in controller.ctrl->hcor.

Introduce define CONFIG_CI_UDC_HAS_HOSTPC to indicate which variant of
the controller should be supported. The "HAS_HOSTPC" part of this name
mirrors the similar "has_hostpc" field used by the Linux EHCI controller
core to represent the presence/absence of the hostpc1_devlc register.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-04-30 10:30:57 +02:00
Stephen Warren
0c51dc6db9 usb: ci_udc: make PHY initialization conditional
usb_gadget_register_driver() currently unconditionally programs PORTSC
to select a ULPI PHY. This is incorrect on at least the Tegra boards I
am testing with, which use a UTMI PHY for the OTG ports. Make the PHY
selection code conditional upon the specific EHCI controller that is in
use.

Ideally, I believe that the PHY initialization code should be part of
ehci_hcd_init() in the relevant EHCI controller driver, or some board-
specific function that ehci_hcd_init() calls.

For MX6, I'm not sure this PHY initialization code is correct even before
this patch, since ehci-mx6's ehci_hcd_init() already configures PORTSC to
a board-specific value, and it seems likely that the code in ci_udc.c is
incorrectly undoing this. Perhaps this is not an issue if the PHY
selection register bits aren't implemented on this instance of the MX6
USB controller?

ehci-mxs.c doens't appear to touch PORTSC, so this code is likely still
required there.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-04-30 10:30:57 +02:00
Stephen Warren
8aac6e9c53 usb: ci_udc: set ep->req.actual after transfer
At least drivers/usb/gadget/storage_common.c expects that ep->req.actual
contain the number of bytes actually transferred. (At least in practice,
I observed it failing to work correctly unless this was the case).

However, ci_udc.c modifies ep->req.length instead. I assume that .length
 is supposed to represent the allocated buffer size, whereas .actual is
supposed to represent the actual number of bytes transferred. In the OUT
transaction case, this may happen simply because the host sends a smaller
 packet than the max possible size, which is quite legal. In the IN case,
transferring fewer bytes than requested could presumably happen as an
error.

Modify handle_ep_complete() to write to .actual rather than modifying
.length.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-04-30 10:30:57 +02:00
Stephen Warren
f5c03006dd usb: ci_udc: Support larger packets
ci_ep_queue() currently only fills in the page0/page1 fields in the
queue item. If the buffer is larger than 4KiB (unaligned) or 8KiB
(page-aligned), then this prevents the HW from knowing where to write
the balance of the data.

Fix this by initializing all 5 pageN pointers, which allows up to
16KiB (potentially non-page-aligned) buffers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-04-30 10:30:57 +02:00
andrey.konovalov@linaro.org
e6e493f341 exynos: usb: Fix data abort on boards w/o vbus-gpio node in the DT
Commit 4a271cb1b4 doesn't take into account that fdtdec_setup_gpio()
returns success when the gpio passed to it is FDT_GPIO_NONE (no
gpio node found in the fdtdec_decode_gpio() call). This results in
calling gpio_direction_output() on invalid gpio. For this reason
executing "usb start" command on Arndale causes data abort in the
ehci-exynos driver.

Add the fdt_gpio_isvalid() check to fix that problem.

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-04-30 10:30:57 +02:00
Rob Herring
078d7302ac usb: musb: fill in usb_gadget_unregister_driver
Add missing missing disconnect and unbind calls to the musb gadget driver's
usb_gadget_unregister_driver function. Otherwise, any gadget drivers fail
to uninitialize and run a 2nd time.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-04-30 10:30:57 +02:00
Rob Herring
52d45012ff usb: handle NULL table in usb_gadget_get_string
Allow a NULL table to be passed to usb_gadget_get_string for cases
when a string table may not be populated.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-04-30 10:30:57 +02:00
Przemyslaw Marczak
fd2a89b20b usb:gadget:f_thor: fix write to filesystem by add dfu_flush()
Since dfu read/write operations needs to be flushed manually,
writing to filesystem on MMC by thor was broken. MMC raw write
actually is working fine because current dfu_flush() function
writes filesystem only. This commit adds dfu_flush() to f_thor
and now filesystem write is working.

This change was tested on Trats2 board.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-04-30 10:30:57 +02:00
Przemyslaw Marczak
adfc17bf09 usb:gadget:f_thor: code cleanup in function download_tail()
In thor's download_tail() function, dfu_get_entity() is called
before each dfu_write() call and the returned entity pointers
are the same. So dfu_get_entity() can be called just once and
this patch changes this.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-04-30 10:30:57 +02:00
Adrian Cox
ea42777567 usb: Add endian support macros to interrupt transfers in the EHCI driver.
Update the EHCI driver to support interrupt transfers on PowerPC.

Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
2014-04-30 10:30:56 +02:00
Nobuhiro Iwamatsu
ede4d5e387 usb: ehci: rmobile: Add support ehci host driver of rmobile SoCs
The rmobile SoC has usb host controller.
This supports USB controllers listed in the R8A7790, R8A7791 and R8A7740.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2014-04-30 10:30:56 +02:00
Nikhil Badola
896720ceb2 fsl/usb: Increase TXFIFOTHRESH value for usb write in T4 Rev 2.0
Increase TXFIFOTHRES field value in TXFILLTUNING register of usb for T4 Rev 2.0.
This decreases data burst rate with which data packets are posted from the TX
latency FIFO to compensate for latencies in DDR pipeline during DMA.
This avoids Tx buffer underruns and leads to successful usb writes

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Nikhil Badola
11856919f2 fsl/usb: Workaround for USB erratum-A007075
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
        P1010 rev 1.0
        B4860 rev 1.0, 2.0
        P4080 rev 2.0, 3.0

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Nikhil Badola
0ecb15c8e9 fsl/usb: Fix phy type for Second USB controller
Set correct phy_type value for second USB controller.
This is required for supporting SOCs having 2 USB controllers
working simultaneously, one with UTMI phy and other with ULPI phy

Signed-off-by: Nikhil Badola <B46172@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:45 -07:00
Stefan Agner
8f9fd6caaf usb: tegra: combine header file
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.

Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stefan Agner
b1d615f3f1 usb: tegra: fix PHY configuration
On Tegra30 and later, the PTS (parallel transceiver select) and STS
(serial transceiver select) are part of the HOSTPC1_DEVLC_0 register
rather than PORTSC1_0 register. Since the reset configuration
usually matches the intended configuration, this error did not show
up on Tegra30 devices.

Also use the slightly different bit fields of first USB, (USBD) on
Tegra20 and move those definitions to the Tegra20 specific header
file.

Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Stefan Agner
b03f4b3742 usb: tegra: fix USB2 powerdown for Tegra30 and later
Clear the forced powerdown bit in the UTMIP_PLL_CFG2_0 register
which brings USB2 in UTMI mode to work. This was clearly missing
since the forced powerdown bit is set in reset by default for all
USB ports.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Heiko Schocher
001a831986 usb: dfu: introduce dfuMANIFEST state
on nand flash using ubi, after the download of the new image into
the flash, the "rest" of the nand sectors get erased while flushing
the medium. With current u-boot version dfu-util may show:

Starting download: [##################################################] finished!
state(7) = dfuMANIFEST, status(0) = No error condition is present
unable to read DFU status

as get_status is not answered while erasing sectors, if erasing
needs some time.

So do the following changes to prevent this:

- introduce dfuManifest state
  According to dfu specification
  ( http://www.usb.org/developers/devclass_docs/usbdfu10.pdf ) section 7:
  "the device enters the dfuMANIFEST-SYNC state and awaits the solicitation
   of the status report by the host. Upon receipt of the anticipated
   DFU_GETSTATUS, the device enters the dfuMANIFEST state, where it
   completes its reprogramming operations."

- when stepping into dfuManifest state, sending a PollTimeout
  DFU_MANIFEST_POLL_TIMEOUT in ms, to the host, so the host
  (dfu-util) waits the PollTimeout before sending a get_status again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-23 02:20:09 +01:00
Gerhard Sittig
df4fb1c36d usb: net: introduce support for Moschip USB ethernet
introduce an 'mcs7830' driver for Moschip MCS7830 based (7730/7830/7832)
USB 2.0 Ethernet Devices

see "MCS7830 -- USB 2.0 to 10/100M Fast Ethernet Controller" at
http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=109;74;109

the driver was implemented based on the U-Boot Asix driver with
additional information gathered from the Moschip Linux driver,
development was done on "Delock 61147" and "Logilink UA0025C" dongles

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-12 17:04:31 -04:00
Stephen Warren
eb838e7d84 usb: create common header virtual root hub descriptors
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.

Note that there were some very minor differences between the descriptors
in the various files, such as:

- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content

I assume these aren't relevant.

Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-03-10 18:53:36 +01:00
Stephen Warren
8165e34bf4 usb: ehci: fully align interrupt QHs/QTDs
These data structures are passed to cache-flushing routines, and hence
must be conform to both the USB the cache-flusing alignment requirements.
That means aligning to USB_DMA_MINALIGN. This is important on systems
where cache lines are >32 bytes.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-03-10 18:53:36 +01:00
Stephen Warren
2456b97f0c ush: ehci: initialize altnext pointers in QH
Section 4.10.2 "Advance Queue" of ehci-specification-for-usb.pdf
specifies how an EHCI controller loads a new QTD for processing if the
QH is not already marked as active. It states:

=====
If the field Bytes to Transfer is not zero and the T-bit in the Alternate
Next qTD Pointer is set to zero, then the host controller uses the
Alternate Next qTD Pointer. Otherwise, the host controller uses the Next
qTD Pointer. If Next qTD Pointer’s T-bit is set to a one, then the host
controller exits this state and uses the horizontal pointer to the next
schedule data structure.
=====

Hence, we must ensure that the alternate next QTD pointer's T-bit
(TERMINATE) is set, so the EHCI controller knows to use the next QTD
pointer.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-03-10 18:53:36 +01:00
Stephen Warren
9a04a858eb net: asix: don't pad odd-length TX packets
For Ethernet/USB RX packets, the ASIX HW pads odd-sized packets so that
they have an even size. Currently, asix_recv() does remove this padding,
and asic_send() adds equivalent padding in the TX path. However, the HW
does not appear to need this packing for TX packets in practical testing
with "ASIX Elec. Corp. AX88x72A 000001" Vendor: 0x0b95 Product 0x7720
Version 0.1. The Linux kernel does no such padding for the TX path.

Remove the padding from the TX path:

* For consistency with the Linux kernel.
* NVIDIA has a Tegra simulator which validates that the length of USB
  packets sent to an ASIX device matches the packet length value inside
  the packet data. Having U-Boot and the kernel do the same thing when
  creating the TX packets simplifies the simulator's validation.

Cc: Lucas Stach <dev@lynxeye.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-03-07 10:59:06 -05:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Tom Rini
a7e8c15f71 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-25 13:55:49 -05:00
Nikhil Badola
91d7746df8 fsl/usb: Limit phy_type comparison to first four characters
Use first four characters for phy_type comparison. Strcmp() should not
be used to check the phy_type string which maybe parsed by hwconfig_subarg().
Hwconfig_subarg() returns part of hwconfig string starting from
phy_type value till the end of the string. Since phy_type could be
either "utmi" or "ulpi", strncmp() should be used so that a comparison
of "utmi;fsl_ddr:bank_intlv=auto" with "utmi" will succeed.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:57 -08:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Tom Rini
130fbeb1c5 blackfin: Add <asm/clock.h> to numerous drivers
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-20 12:00:27 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Masahiro Yamada
6825a95b0b kbuild: use Linux Kernel build scripts
Now we are ready to switch over to real Kbuild.

This commit disables temporary scripts:
  scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
  scripts/{Makefile.build,Makefile.host,Makefile.lib}.

This switch is triggered by the line in scripts/Kbuild.include
  -build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
  +build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj

We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.

Additionally, we need to fix compiler flags which are
locally added or removed.

In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Marek Vasut
f016f8ca3d usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-02-06 04:48:15 +01:00
Marek Vasut
b1c756782c ARM: USB: Remove the IXP EHCI driver
The driver is no longer used, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Lukasz Majewski
fc2d5d04e1 usb:gadget:f_thor: cosmetic: Remove debug memset
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
84c13e6f61 usb:gadget:f_thor: Allocate request up to THOR_PACKET_SIZE not ep->maxpacket
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
e0059eaef1 usb:udc:samsung: Zero copy approach for data passed to Samsung's UDC driver
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.

This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).

This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurement:
Transmission speed: 27.04 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
9c9822188c usb:udc:samsung: Allow burst transfers for non EP0 endpints
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.

Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurement:
Transmission speed: 20.74 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
716662bd19 usb:udc:samsung: Remove redundant cache operation from Samsung UDC driver
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:

1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)

2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.

Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.

3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurements:

Base values (without improvement):
Transmission speed: 9.51 MiB/s

After the change:
Transmission speed: 10.15 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
16b7a29fc6 usb:gadget:ums: Replace malloc calls with memalign to fix cache buffer alignment
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:44 +01:00
Inderpal Singh
7da7651251 usb: exynos5: arndale: Add network support
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
2014-01-13 12:23:28 +01:00
Inderpal Singh
16f9480dfc usb: ehci: exynos: set/reset hsic phys
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2014-01-13 12:23:28 +01:00
Kuo-Jung Su
dcad280056 usb: gadget: fotg210: EP0 fifo empty indication is non-reliable
The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.

However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)

After a couple of tests, it truns out that 1 usec is good enough.

This workaround should be applied to all hardware revisions.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:13 +01:00
Kuo-Jung Su
bd5e301d35 usb: gadget: fotg210: add w1c interrupt status support
Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):

1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)

And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:12 +01:00
Marek Vasut
eb63218b9b usb: ehci: Fix register access
Fix the register access in EHCI HCD. We need to use address of the register
as an ehci_writel() argument.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Marek Vasut
1e1be6d478 usb: ehci: Do not de-init uninited controllers
In case the controller is not initialized, we shall not de-initialize it.
As the control structure will not be filled, we will produce a null ptr
dereference if the controller is not inited.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Marek Vasut
8fb83547b9 usb: ehci-pci: Clarify and cleanup the EHCI controller detection
The detection function of the EHCI PCI controller was really cryptic,
add a beefy comment and clean the portion of the code up a bit. No
change in the logic of the code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Lukasz Majewski
77b9504288 usb: f_dfu: cosmetic: Code cleanup
Code cleanup for dfu_bind_config function

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-12-18 19:53:19 +01:00
Lukasz Majewski
33fac4a6a2 usb: dfu: f_dfu: Provide infrastructure to adjust DFU's Poll Timeout value
It is necessary to deter the host from sending subsequent DFU_GETSTATUS
request in the case of e.g. writing the buffer to medium.

Here the timeout is increased when we fill up the whole buffer. This delay
allows eMMC memory to perform its internal operations.
Otherwise we end up with HOST's error regarding GET_STATUS receive timeout.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-12-18 19:53:19 +01:00
Masahiro Yamada
4f57a90cfa drivers/usb/gadget: select objects by obj-$(CONFIG-...)
Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.

We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-13 09:18:44 -05:00
Albert ARIBAUD
375a4496ff Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-12-06 16:54:42 +01:00
Roger Quadros
835a5559bd usb: ehci-omap: Reset the USB Host OMAP module
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).

On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.

This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.

Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-06 07:02:32 -05:00
Piotr Wilczek
4498cf252b driver:usb:s3c_udc: add support for Exynos4x12
This patch add new defines for usb phy for Exynos4x12.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-02 11:22:32 +09:00
Heiko Schocher
7a0d463f58 usb, g_dnl: make bcdDevice value configurable
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
2013-11-12 09:53:59 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Heiko Schocher
ec9002e4fa usb, g_dnl: make iSerialNumber board configurable
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08 20:46:20 +01:00
Mateusz Kulikowski
522c95647d usb: ohci-hcd: submit_common_msg: report actual_length properly
submit_common_msg should report amount of data passed from/to device.
Instead, it always returned size requested by Host.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
351e9b2069 usb: ums: add ums exit feature by ctrl+c or by detach usb cable
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.

Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.

Changes v2:
- add a note to the README

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
0697f206df usb: ums: fix disk capacity miscalculation and code cleanup
This patch prevents:
- ums disk capacity miscalculation because of integer overflow

Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
  initialization before gadget init
- Remove unnecessary code from mass storage driver

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
93c813b3ac usb: ums: code refactoring to improve reusability on other boards.
This patch introduces some cleanups to ums code. Changes:

ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
  usb_mass_storage.h both default values as 0 if board config
  doesn't define them

common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h

cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string

Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
2013-11-08 20:46:19 +01:00
Bo Shen
dcd2f1a0d2 arm: atmel: get rid of too many ifdeffery
Get rid of too many ifdeffery in usb ohci driver

Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:37 +01:00
Bo Shen
d9bef0ad2d arm: atmel: at91sam9n12ek: add usb host support
Add usb host support for at91sam9n12ek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:35 +01:00
Masahiro Yamada
44e32c7144 drivers: usb: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:25:38 -04:00
ramneek mehresh
77354e9d50 powerpc/usb:Differentiate USB controller base address
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-10-24 09:35:09 -07:00
Troy Kisky
7e575c46c3 usb: rename board_usb_init_type to usb_init_type
commit bba679144d
"usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c
So, fix that patch here, and fix a checkpatch warning.
WARNING: Avoid unnecessary line continuations

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-22 17:33:09 -04:00
Troy Kisky
449697f14e usb: udc: add udc.h include file
Move common definitions to udc.h
This allows musb_udc.h to be removed as well.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:38 +02:00
Troy Kisky
0f740cb8e4 usb: gadget: mv_udc: split mv_udc.h file
Move defines only needed by mv_udc.c to a file
in the same directory.

This allows usbtty to compile for mv_udc,
but it still doesn't link.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:36 +02:00
Troy Kisky
7b7924cdf8 usb: gadget: mv_udc: optimize ep_enable
Only get head if not ep0.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:33 +02:00
Troy Kisky
1ebf02787a usb: gadget: mv_udc: optimize bounce
Only perform one copy, either in the bounce
routine for IN transfers, or the debounce
rtn for OUT transfer.

On out transfers, only copy the number
of bytes received from the bounce buffer

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:33 +02:00
Troy Kisky
3b59abf583 usb: gadget: mv_udc: fix full speed connections
Set maximum packet length in queue header to wMaxPacketSize
of endpoint.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:33 +02:00
Troy Kisky
d1a5286099 usb: ehci-mx6: add support for otg port
Previously, only host1 was supported using an index of 0.
Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3.
Since OTG requires usbmode to be set after reset, I added
CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and
mx6qsabreauto.h.

I also added a weak function board_ehci_power to handle
turning power on/off for otg.

Type is type of device connected (USB stick vs Host.)
Init is type of device desired.
Only power up port if type == init == USB_INIT_HOST.
Only return error if type != init.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:33 +02:00
Troy Kisky
8287314888 usb: gadget: mv_udc: don't check CONFIG_USB_MAX_CONTROLLER_COUNT
i.mx6 has 1 otg controller, and 3 host ports. So,
CONFIG_USB_MAX_CONTROLLER_COUNT can be greater than 1
even though only 1 device mode controller is supported.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:29 +02:00
Troy Kisky
127efc4fe8 usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.
This paramter will later be used to initialize OTG ports in
host or device mode.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:27 +02:00
Troy Kisky
06d513ecb6 usb: add enum usb_init_type parameter to usb_lowlevel_init
This parameter will later be used to verify OTG ports.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:45:26 +02:00
Dan Murphy
3d799c7f5e usb: am437x: Add support for am437x xhci USB host
Add the support for the am437x xhci usb host.

The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
ba55453ccf usb: omap: Move the usb phy code to the usb/phy directory
Moving the usb/phy code from xhci-omap to the usb/phy directory
and moving the associated phy code over to the new file.

Newer TI processors adding xHCI support will have different PHY configurations
so therefore abstracting this code away will prevent messing around with the
xhci-omap file itself.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
b216821189 usb: omap5: Update the board_usb_init api
Recent patches declares board_usb_init function prototype for a new
usb architecture.

Turning on the OMAP_XHCI defines cause a redefinition compiler failure.
So update the board_usb_init to the latest prototype.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
41b667b834 usb: omap: Move the xhci-omap header file to common location
Moving the xhci-omap header to a more global location so that
other code can reference this code.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Lukasz Majewski
b958fb9165 usb:g_dnl: Support for TIZEN's THOR function in generic download code
Support of "thor" function in generic download code (g_dnl.c).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:41 +02:00
Lukasz Majewski
c527937796 usb:g_dnl:f_thor: USB download function to support TIZEN's THOR protocol
Implementation of USB download function which supports THOR protocol.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:41 +02:00
Lukasz Majewski
d6eae7b0b1 usb:g_dnl: Add name parameter to g_dnl_bind_fixup function
New parameter, namely *name has been added to g_dnl_bind_fixup().
It is necessary (for compatibility reasons) to assign new USB idProduct
and idVendor for different usb functions.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:41 +02:00
Lukasz Majewski
7b412ab31f usb:g_dnl: Replace static usb_configuration structure with dynamically allocated one
When the usb_configuration structure is declared as static, it is very
hard to assure, that relevant fields (as e.g. config->interfaces[]) are
cleared out before new call to g_dnl related functions.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20 23:42:40 +02:00
Lukasz Majewski
57ffabe371 usb:udc:s3c: Reduce dcache invalidate range for UDC receive buffer
The s3c udc driver sends data in a max packet size. Therefore the dcache
invalidate range shall be equal to max packet, not the entire
DMA_BUFFER_SIZE.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:40 +02:00
Suriyan Ramasami
98f686c26f usb:smsx95xx LED activity for USB net driver
Add LED activity for SMSX95XX USB Ether driver.

Signed-off-by: “Suriyan Ramasami" <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-10-20 23:42:40 +02:00
Mateusz Zalega
16297cfb2a usb: new board-specific USB init interface
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.

New API allows selective initialization of USB controllers whenever needed.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20 23:42:40 +02:00
Troy Kisky
b065eb7fd7 usb: gadget: mv_udc: clear desc upon ep_disable
desc is set at ep_enable, so for symmetry,
clear it at ep_disable.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:40 +02:00
Troy Kisky
01773ccc0d usb: gadget: mv_udc: zero transfer descriptor memory on probe
Since we flush the TD, we may as well set it to a known value.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Troy Kisky
5fc2e99732 usb: gadget: mv_udc: flush item before head
Make sure the transfer descriptor is flushed
before the queue is updated so that the controller
will not see old information.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Troy Kisky
5a90443048 usb: gadget: mv_udc: set is_dualspeed = 1
This controller support full and high speed.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Troy Kisky
d0928794d9 usb: gadget: mv_udc: fix typo in error message
Change 'nfo=' to 'info='

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Troy Kisky
71fc5f91d2 usb: gadget: ether: return error from rx_submit if no request
This prevents a crash if tftpboot is given a bad filename.

rx_req will be released by eth_reset_config
which is called by eth_disconnect,
which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc
which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect
which is called by usb_eth_halt
which is called using the .halt member of eth_device by eth_halt
which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs

I trigger this with the following commands
setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1
setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee
setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1
tftpboot 10800000 10.0.0.1:missing_file

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Troy Kisky
43880ce5be usb: gadget: ether set wMaxPacketSize
set wMaxPacketSize for full speed descriptors
fs_source_desc, fs_sink_desc to 64.

Full-speed bulk endpoint can have a maximum packet size of
8, 16, 32, or 64 bytes, so choice 64.

The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize
set to 512. That is the only legal value for high speed bulk endpoints.

Strictly speaking, this patch is not needed because
usb_ep_autoconfig will call ep_matches which will
override wMaxPacketSize for BULK endpoints only with
the size associated with the endpoint setup by the udc driver.
But if you want to rely on this, you may as well combine the
full speed descriptor with the high speed descriptor to
minimize confusion.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:39 +02:00
Dan Murphy
2d2358ac15 OMAP5: USB: Add OMAP xHCI file and header
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Julius Werner
4a271cb1b4 exynos: usb: Switch USB VBUS GPIOs to be device tree configured
Some Exynos boards, such as the SMDK5250, control USB port power through
a GPIO pin. For now this had been hardcoded in the exynos5-dt board
file, but not all boards use the same pin, requiring local changes to
support different boards.

This patch moves the GPIO initialization into the USB host controller
drivers which they belong to, and uses the samsung,vbus-gpio parameter
in the device tree to configure it.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Vivek Gautam
13194f3b5f USB: XHCI: Add xHCI host controller support for Exynos5
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.

Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Vivek Gautam
5853e1335c USB: xHCI: Add stack support for xHCI
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.

Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.

Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found

This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
  infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.

Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Vivek Gautam
e3d7440c22 usb: Move 'bmRequestType' USB device request macros from EHCI header
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00
Wolfgang Denk
16641d52fc Coding Style cleanup: drop some excessive empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
d4c8aa9cb4 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Andrew Murray
99b4eaa68e usb: Prevent using reserved registers on DM36x usb
The musb driver defines and uses MUSB_CSR0_H_DIS_PING, however this
bit is reserved on the DM36x. Thus this patch ensures that the
reserved bit is not accesssed.

It has been observed that some USB devices will fail to enumerate
with errors such as 'error in inquiry' without this patch.

See http://www.ti.com/litv/pdf/sprufh9a for details.

Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Acked-by: Marek Vasut <marex@denx.de>
2013-10-10 07:58:00 -04:00
Tom Rini
9f3fe6da27 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-08 09:51:48 -04:00
Andrew Murray
ddd025bb6e usb: Fix error handling in musb_hcd.c
The wait_until_[rx|tx]ep_ready functions return a u8 to indicate success
containing the value 0, 1 or -1. This patch changes the return type to an
int to accommodate the negative return values.

These functions are used in the file using calls such as if (!wait_until...
Where a -1 is returned it is mishandled and treated as success instead of
a CRC error. This patch addresses this.

Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Acked-by: Marek Vasut <marex@denx.de>
2013-10-07 07:43:46 -04:00
Julius Werner
5077f96f10 usb: ehci: Fix test mode for connected ports
The EHCI controller has some very specific requirements for the USB 2.0
port test modes, which were not closely followed in the initial test
mode commit. It demands that the host controller is completely shut down
(all ports suspended, Run/Stop bit unset) when activating test mode, and
will not work on an already enumerated port.

This patch fixes that by introducing a new ehci_shutdown() function that
closely follows the procedure listed in EHCI 4.14. Also, when we have
such a function anyway, we might as well also use it in
usb_lowlevel_stop() to make the normal host controller shutdown cleaner.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2013-09-27 16:20:52 +02:00
Bo Shen
4585fc5863 USB: gadget: atmel: disconnect before unbind
When unbind the gadget driver, need call disconnect first.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24 17:51:36 +02:00
Lukasz Majewski
a6921adcf2 usb:g_dnl:dfu: Download gadget and DFU function code clean up
The download gadget code and DFU function lacks of proper declarations
for the case when a target board wants to use only one of available usb
functions.

Moreover the relevant declarations have been moved to consistent
localization (like <dfu.h>).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-09-24 17:51:36 +02:00
Lukasz Majewski
69d6cbe748 usb:gadget:Remove redundant #includes for USB composite gadget and its functions
Only the <linux/usb/gadget.h> requires error.h include. Hence, several
includes of error.h at USB gadget functions are not needed.

Moreover unnecessary malloc.h includes were also removed.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-09-24 17:51:36 +02:00
Lukasz Majewski
ba4e95c9f0 usb:g_dnl:ums: Conditional compilation for mass storage function (f_mass_storage)
The mass storage composite function is now compiled in only when
CONFIG_USB_GADGET_MASS_STORAGE is defined.
Such change provides binary size reduction for boards which use USB
download gadget (like am335x_evm) with DFU, but don't use UMS.

For example at am335x_evm board reduction is more than 2KiB for
text and around 120B for data.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-09-24 17:51:35 +02:00
Bo Shen
9e40493fd8 USB: gadget: add atmel usba udc driver
Add atmel usba udc driver support, porting from Linux kernel

The original code in Linux Kernel information is as following

commit e01ee9f509a927158f670408b41127d4166db1c7
Author: Jingoo Han <jg1.han@samsung.com>
Date:   Tue Jul 30 17:00:51 2013 +0900

    usb: gadget: use dev_get_platdata()

    Use the wrapper function for retrieving the platform data instead of
    accessing dev->platform_data directly.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24 17:51:35 +02:00
Troy Kisky
898d686eea usb: gadget: config: fix unaligned access issues
As seen with codesourcery compiler 2010q1, the buf pointer in
usb_request structure is not aligned on 4 bytes boundary causing
data aborts in eth_setup -> conf_buf -> usb_gadget_config_buf.
Make it as align access to fix this issue.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[voice.shen@atmel.com: add commit message]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24 17:51:35 +02:00
Joel Fernandes
5290759cc4 usb: gadget: Fix data aborts during USB ethernet boot
As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned
on 4 byte boundaray causing data aborts in eth_setup -> conf_buf
during dhcp boot over usb_ether. Fix the issue my aligning control_req
buffer using DEFINE_CACHE_ALIGN_BUFFER.

Tested on am335x_evm platform (beaglebone).
Applies on 2013.10-rc1 branch.

Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
2013-09-24 17:51:34 +02:00
Albert ARIBAUD
4eef93da26 Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-09-04 11:50:25 +02:00
Fabio Estevam
76b6b19614 usb: ehci-mx5: Use 'bool' instead of 'unsigned char'
The 'enable' argument can be better expressed as boolean.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-26 21:56:34 +02:00
Fabio Estevam
c3904128ad usb: ehci-mx5: Remove unneeded write to cscmr1 register
Currently we have the following behavior in ehci_hcd_init()

- Read csmr1 register, clear bit 26 and then set bit 26.

However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-08-26 21:56:34 +02:00
Lukasz Majewski
c4219a82cd usb:dfu:g_dnl: Refactoring the string definition code for g_dnl driver
The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
2013-08-26 21:56:34 +02:00
Lukasz Majewski
cfc2d0d632 usb:dfu:g_dnl: Change number of exported configurations at composite gadget
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.

Moreover more descriptive names were chosen for relevant fields.

Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.

Tested at: Trats - Exynos4210

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
2013-08-26 21:56:34 +02:00
Dan Murphy
120503f32e ARM: OMAP: USB: Fix linker error when ULPI is not defined
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-08-26 21:55:46 +02:00
Dan Murphy
d3d037ae18 ARM: OMAP5: USB: Add OMAP5 common USB EHCI information
* Enable the OMAP5 EHCI host clocks
* Add OMAP5 EHCI register definitions
* Add OMAP5 ES2 host revision

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26 21:55:46 +02:00
Wu, Josh
2f96b06be5 linux/compat.h: move dev_err, dev_info and dev_dbg from usb driver to compat.h
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.

This patch also removed duplicated macro definitions in usb driver.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:50:29 +02:00
Wolfgang Denk
cb3761ea99 SPDX-License-Identifier: convert BSD-3-Clause files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19 15:45:35 -04:00
Stefan Roese
2eb60902a0 net: smsc95xx: Add support for another SMSC95xx variant
This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.

Tested on omap3_beagle.

Signed-off-by: Stefan Roese <sr@denx.de>
2013-08-19 12:34:18 -05:00
Tom Rini
e20cc2ca15 Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-18 14:14:34 -04:00
Lokesh Vutla
32f420b8ec musb: Disable extra prints
There are many musb prints in SPL and U-Boot log.
These prints are required only during musb debug.
So replacing printk with pr_debug in musb_core.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Nikita Kiryanov
8bc3603675 ehci-hcd: fix memory leak in lowlevel init
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.

Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-07-29 23:01:33 +02:00
Roger Quadros
bb1f327d0a usb: ehci-omap: Don't softreset USB High-speed Host (UHH) Module
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.

Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.

See OMAP36xx Errata
  i571: USB host EHCI may stall when entering smart-standby mode
  i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock

On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.

On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
 e.g. NFS root failures with Linux kernel.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-07-29 23:01:33 +02:00
Lukasz Majewski
6bed7ce569 dfu: Implementation of target reset after communication with dfu-util's -R switch
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.

When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2013-07-29 23:01:33 +02:00
Marek Vasut
6dd30af0fa usb: mv_udc: Add bounce buffer
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:33 +02:00
Marek Vasut
f19a343e73 usb: mv_udc: Add proper cache management
Implement functions to flush/invalidate dcache over QH and qTDs
and make use of them where appropriate. Also use them to replace
the old incorrect cache management attempt. This is the first step
towards making this driver work with data cache enabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:33 +02:00
Marek Vasut
ede709c0d2 usb: mv_udc: Implement better qTD item accessor
The code for retrieving qTD item for particular endpoint is hard
to understand, moreover it's duplicated all over the driver. Move
the code into single nice and documented function.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:33 +02:00
Marek Vasut
8a095a68ce usb: mv_udc: Improve allocation of qTD items
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
b5cd45bfad usb: mv_udc: Implement better QH accessor
The code for retrieving QH for particular endpoint is hard to understand,
moreover it's duplicated all over the driver. Move the code into single
nice and documented function.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
5804b8859a usb: mv_udc: Add cacheline length check
Check the length of system cacheline at compile-time and fail
if the system uses too long cachelines.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
ab65da1446 usb: mv_udc: Properly align the endpoint QH and qTD list
The endpoint QH list has to be aligned to 10-bit boundary. We also have
to make sure the list is aligned on a cacheline boundary. Make sure it
is. Furthermore, check if the memory allocation for the QH list didn't
fail. Moveover, improve the comment about the QH list structure.

Finally, the qTD item list has to be aligned only to 5-bit boundary, not
10-bit as it is now, fix this as well.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
ab52df19c1 usb: mv_udc: Move QH and qTD into mv_drv
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
fe48f05817 usb: mv_udc: Init mv_drv.gadget.ops statically
There is no need to init this field at runtime, so init it statically.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
f646317739 usb: mv_udc: Remove QH_MAXNUM macro
The QH_MAXNUM is used in absolutelly incorrect manner and is not
even needed. Remove it and correctly replace it's occurance with
2 * NUM_ENDPOINTS .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:32 +02:00
Marek Vasut
d76630386d usb: mv_udc: Clean up the initial variable check
Clean up the code that checks the validity of a USB gadget driver
in usb_gadget_register_driver(). Moreover, limit the speed of the
driver to either FULL or HIGH, this is more precise and once we
have xHCI support, also more correct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Marek Vasut
be7ed2533d usb: mv_udc: Make use of struct ehci_ctrl
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.

Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Marek Vasut
b959655f18 usb: ehci: Split out struct ehci_ctrl definition
Move the struct ehci_ctrl defition from ehci-hcd.c into ehci.h
so it can be re-used by drivers. In particular, the mv_udc driver
can benefit from this move.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Marek Vasut
2ea4b44832 usb: mv_udc: Clean up the EP initialization
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.

Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Marek Vasut
532d846f89 usb: mv_udc: Move endpoint array into driver data
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Marek Vasut
a7eafcfe45 usb: mv_udc: Unbreak the mv_udc driver
The mv_udc driver is broken for a while and doesn't even compile.
This patch fixes the issues and gets the driver into working state
again. This driver was tested on Freescale i.MX233/i.MX28 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-07-29 23:01:31 +02:00
Wolfgang Denk
eee479cf6a Add LGPL-2.1+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-07-24 09:45:01 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
fbbbc86e8e Merge branch 'master' of git://git.denx.de/u-boot-arm
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
	arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12 10:36:48 -04:00
Jim Lin
7e44d9320e ARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114
Tegra30 and Tegra114 are compatible except PLL parameters.

Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-07-11 14:15:15 -07:00
Mike Dunn
ecc8edbf69 usb: pxa27x_udc: fix compiler warnings
Newer gcc versions warn about unused variables.  This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-07-10 20:18:57 +02:00
Łukasz Majewski
81c065d2a0 dfu: Update DFU's authorship history
The DFU's state machine original implementation author and copyright were
missing.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
2013-07-10 20:18:57 +02:00
Michael Trimarchi
b0857c45c1 usb: omap: ulpi: fix ulpi transceiver access
This patch fix the omap access to the transceiver
configuration registers using the ulpi bus. As reported by
the documentation the bit31 is used only to check if the
transaction is done or still running and the reading and
writing operation have different offset and have different
values. What we need to do at the end of a transaction is
leave the bus in done state. Anyway an error using the ulpi
omap register is not recoverable so any error give out the
usage of this interface.

Tested on a custom OMAP5430 board with a TUSB1210 ULPI PHY
on USBB1.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-07-02 09:21:15 -04:00
Pierre Aubert
befd387242 usb: add support for the USB Ethernet adapter D-Link DUB-E100 H/W Ver C1
This trivial patch adds the definition of the vid/pid for the Ver C1 of the
USB Ethernet adapter D-Link DUB-E100.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Marek Vasut <marex@denx.de>
2013-06-30 18:41:08 +02:00
Lukasz Majewski
e059a400ad dfu:function: Fix number of allocated DFU function pointers
This subtle change fix problem with too small amount of allocated
memory to store DFU function pointers.

One needs to allocate extra space for sentinel NULL pointer in this array
of function pointers.

With the previous code, the NULL value overwrites malloc internal data
and afterwards free(f_dfu->function) crashes.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-06-30 18:41:08 +02:00
Heiko Schocher
7a34278542 usb, musb-new: add wdt trigger
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
2013-06-30 18:41:07 +02:00
Heiko Schocher
c5398cc968 usb, g_dnl: make possibility to fixup the device_desc board specific
add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2013-06-30 18:41:07 +02:00
Heiko Schocher
ad5f977889 usb, dfu gadget: switch to dfu mode in dfu_bind
- set in to_dfu_mode() f_dfu->dfu_state = DFU_STATE_dfuIDLE
  as after every to_dfu_mode call this is done, so move
  this into to_dfu_mode
- switch in dfu_bind() into dfu mode:
  This fixes wrong "dfu-util -l" output, when calling
  "dfu-util -l" after a board reset, without doing a
  download before. See also discussion here:

http://lists.denx.de/pipermail/u-boot/2013-June/157272.html

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-06-30 18:41:07 +02:00
Piotr Wilczek
12595e99e4 usb:composite: use memcpy to avoid unaligned access
This patch memcpy is used instead of an assignment to
avoid unaligned access execption on some ARM platforms.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-06-30 18:41:07 +02:00
Piotr Wilczek
7f3cf4060f drivers:usb: use get|put_unaligned_le16
This patch use get|put_unaligned_le16 to access structure data
to avoid data abort on some ARM platforms.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marex@denx.de>
2013-06-30 18:41:07 +02:00
Axel Lin
e31dc61e7d usb: musb: Use ARRAY_SIZE at appropriate places
Signed-off-by: Axel Lin <axel.lin@ingics.com>
2013-06-26 10:26:06 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Heiko Schocher
c67b0e42a5 usb, composite: after unregister gadget driver set composite to NULL
Without this, second usb_composite_register() call fails always
with -EINVAL.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-06-12 22:22:52 +02:00
Stephen Warren
d3e0747846 usb: ehci: add missing cache managment
Commit 8f62ca6 "usb: ehci: Support interrupt transfers via periodic list"
didn't include any cache management in the new interrupt transfer path.
It also added an extra write to or_asynclistaddr in usb_lowlevel_init(),
without having flushed out the data there.

Add the missing cache management calls, so that the code works again.

This allows the USB keyboard on Tegra's Seaboard/Springbank boards to
work.

Cc: Patrick Georgi <patrick@georgi-clan.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-06-12 22:22:52 +02:00
Kuo-Jung Su
64cfd3f964 usb: gadget: add Faraday FOTG210 USB gadget support
The Faraday FOTG210 is an OTG chip which could operate
as either an EHCI Host or a USB Device at a time.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:52 +02:00
Kuo-Jung Su
e82a316d7f usb: ehci: add Faraday USB 2.0 EHCI support
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:

1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
   also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
   compatible with the general TDI implementation
   found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
   several ways. But since U-boot doesn't support ISOC,
   we don't have to worry about that.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Kuo-Jung Su
1dde1423ad usb: ehci: add weak-aliased function for PORTSC
There is at least one non-EHCI compliant controller (i.e. Faraday EHCI)
not only leave RESERVED and CONFIGFLAG registers un-implemented
but also has their address spaces removed.

As an result, the PORTSC register of Faraday EHCI always
starts from 0x30 instead of 0x44 in standard EHCI.

So that we'll need a weak-aliased function for abstraction.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Kuo-Jung Su
9c6a9d7c8b usb: ehci: prevent bad PORTSC register access
1. The 'index' of ehci_submit_root() is not always > 0.

   e.g.
   While it gets invoked from usb_get_descriptor(),
   the 'index' is always a '0'. (See ch.9 of USB2.0)

2. The PORTSC register is not always required, and thus it
   should only report a port error when necessary.
   It would cause a port scan failure if the ehci_submit_root()
   always gets terminated by a port error.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Vivek Gautam
f6664ba4bc usb: gadget: Use unaligned access for wMaxPacketSize
Use get_unaligned() while fetching wMaxPacketSize to avoid
voilating any alignment rules.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Dalek <luk0104@gmail.com>
Cc: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Julius Werner
4edcf0a3df usb: asix: Move software resets to basic_init
The ASIX driver calls a basic_init() function during get_info(), so that
not all initialization tasks need to be redone on every init().
Unfortunately, the most important one is still triggered too often: the
driver does a full port and MII reset on every asix_init(), requiring up
to several seconds to reestablish the link.

This patch confines that software reset into the asix_basic_init()
function so that it will only be executed once. This saves about a
second of boot time on systems using BOOTP.

Note: this patch was previously submitted many moons ago as:

   usb: usbeth: asix: Do a fast init if link already established

That patch seens to have been lost or forgotten, so this is a rebased
version. It is tested on snow with a Asix USB dongle (Cisco).

Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
2013-06-12 22:22:51 +02:00
Simon Glass
ed10e66aba usb: Correct CLEAR_FEATURE code in ehci-hcd
This commit broke USB2 on link (Chromebook Pixel):

  020bbcb usb: hub: Power-cycle on root-hub ports

However the root cause seems to be a missing mask and missing 'break'
in ehci-hcd.c. This patch fixes both.

On link, 'usb start' with a USB keyboard and memory stick inserted now
finds both. The keyboard works as expected. Also ext2ls shows a directory
listing from the memory stick.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-06-12 22:22:50 +02:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Albert ARIBAUD
a19b0dd62d Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	common/cmd_fpga.c
	drivers/usb/host/ohci-at91.c
2013-05-30 14:45:06 +02:00
Bo Shen
e5e8bb05a4 USB: ohci-at91: support sama5d3x devices
Add OHCI support for sama5d3x devices

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-21 11:54:13 +02:00
Lubomir Popov
e7dcecea9b OMAP5: Enable USB Ethernet support with LAN9730
Added the LAN9730 to list of supported devices. This chip is used
in the sEVM, uEVM and som5_evb. Tested on the som5_evb with dhcp
and ping.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-05-14 15:37:58 -04:00
Albert ARIBAUD
cac423a730 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-05-11 22:24:28 +02:00
Albert ARIBAUD
ec7023db8d Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/mtd/nand/mxc_nand_spl.c
	include/configs/m28evk.h
2013-05-11 09:25:36 +02:00
Nishanth Menon
b29c2f0c14 twl4030: make twl4030_i2c_read_u8 prototype consistent
u-boot standard i2c read prototype is
i2c_read(addr, reg, 1, &buf, 1)

twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val)

Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10 08:25:54 -04:00
Nishanth Menon
0208aaf6c2 twl4030: make twl4030_i2c_write_u8 prototype consistent
u-boot standard i2c register write prototype is
i2c_reg_write(u8 addr, u8 reg, u8 val)

twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)

Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10 08:25:54 -04:00
Vivek Gautam
4f4eab4d14 usb: common: Use a global definition for 'min3'
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
2013-05-06 02:16:37 +02:00
Bo Shen
158947d276 USB: ohci-at91: make OHCI work on at91sam9g10 SoC
The at91sam9g10 need to configure HCK0 to make OHCI work

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-05-05 23:54:22 +02:00
Julius Werner
7d9aa8fd87 usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.

Signed-off-by: Julius Werner <jwerner@chromium.org>
2013-05-05 23:54:21 +02:00
Mike Dunn
e0e89e236f pxa27x_udc: remove call to unimplemented set_GPIO_mode()
If CONFIG_USB_DEV_PULLUP_GPIO is defined, a link error occurs because the
set_GPIO_mode() helper function is not implemented.  This function doesn't do
much except make the code a little more readable, so I just manually coded its
equivalent and removed the prototype from the header file.  It is invoked no
where else in the code.

While I was at it, I noticed that two other function prototypes in the same
header file are also neither implemented nor invoked anywhere, so I removed them
as well.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-05-05 23:47:05 +02:00
Jim Lin
b068deb363 USB: EHCI: Add weak functions to support new chip
Add ehci_get_port_speed() and ehci_set_usbmode() weak functions
for platform driver to support new chip.

Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-05-05 23:46:41 +02:00
Benoît Thébaudeau
ba5dfc11ba imx: mx5: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2013-05-05 17:55:05 +02:00
Albert ARIBAUD
1812201997 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	drivers/video/exynos_fb.c
2013-04-12 22:07:57 +02:00
Benoît Thébaudeau
e53232250b arm: Remove support for unused s3c64xx
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:08 +02:00
Bin Liu
76b09b8561 musb: set MUSB speed based on CONFIG
Do not config MUSB to highspeed mode if CONFIG_USB_GADGET_DUALSPEED
is not set, in which case Ether gadget only operates in fullspeed.

Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
2013-04-08 11:29:04 -04:00
Bin Liu
4de602f2b0 musb: am335x: disable bulk split-combine feature
On TI AM335x devices, MUSB has bulk split/combine feature enabled
in the ConfigData register, but the current MUSB driver does not
support it yet. Therefore, disable the feature for now, until the
driver adds the support.

One usecase which is broken because of this feature is that Ether
gadget stops working in Fullspeed mode (by un-defining
CONFIG_USB_GADGET_DUALSPEED)

After desabled this feature, MUSB driver send packets in proper size
(no more than 64 bytes) in Fullspeed mode.

This has been validated with Ether gadget in Fullspeed mode on AM335x
EVM.

Signed-off-by: Bin Liu <b-liu@ti.com>
2013-04-08 11:29:04 -04:00
York Sun
472d546054 Consolidate bool type
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.

All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.

Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-04-01 16:33:52 -04:00
Tom Rini
3c47f2f487 Merge branch 'master' of git://git.denx.de/u-boot-usb 2013-03-18 15:33:47 -04:00
Vincent Palatin
ae003d0570 usb: Add multiple controllers support for EHCI PCI
Use the ability to have several active EHCI controller on a system
in the PCI EHCI controller implementation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-18 18:58:55 +01:00
Michael Spang
032868a432 usb: usbeth: smsc95xx: remove EEPROM loaded check
[port of Linux kernel commit bcd218be5aeb by Steve Glendinning]

The eeprom read & write commands currently check the E2P_CMD_LOADED_ bit is
set before allowing any operations.  This prevents any reading or writing
unless a correctly programmed EEPROM is installed.

Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
2013-03-18 18:58:54 +01:00
Vincent Palatin
61755c7908 usb: ehci: Fix aliasing issue in EHCI interrupt code
The interrupt endpoint handling code stores the buffer pointer in the QH
padding field. We need to make it the size of a pointer to avoid strict
aliasing issue with the compiler.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-18 18:58:54 +01:00
Patrick Georgi
8f62ca646f usb: ehci: Support interrupt transfers via periodic list
Interrupt transfers aren't meant to be used from the async list
(the EHCI spec indicates trouble with low/full-speed intr on async).

Build a periodic list instead, and provide an API to make use of it.
Then, use that API from the existing interrupt transfer API.

This provides support for USB keyboards using EHCI.

Use timeouts to ensure we cannot get stuck in the keyboard scanning
if something wrong happens (USB device unplugged or fatal I/O error)

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-18 18:58:54 +01:00
Vivek Gautam
c74b0116b6 usb: ehci: exynos: Enable non-dt path
Enabling the non-dt path for the driver so that
we don't get any build errors for non-dt configuration.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-18 18:58:54 +01:00
Vivek Gautam
24a4775f91 usb: ehci: exynos: Fix multiple FDT decode
With current FDT support driver tries to parse device node
twice in ehci_hcd_init() and ehci_hcd_stop(), which shouldn't
happen ideally.
Making provision to store data in a global structure and thereby
passing its pointer when needed.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-03-18 18:58:53 +01:00
Lukasz Majewski
b528f71394 usb:gadget: USB Mass Storage Gadget support
This patch adds the USB Mass Storage Gadget to u-boot
New command called "ums" is implemented to provide access
to on-device embedded persistent memory.

USB Mass Storage is supposed to work on top of the USB
Gadget framework

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marek.vasut@gmail.com>
2013-03-18 18:58:53 +01:00
Piotr Wilczek
b4d36f6809 usb:composite: USB Mass Storage - f_mass_storage.c from Linux kernel
The f_mass_storage.c source file from v2.6.36 Linux kernel.

commit 8876f5e7d3b2a320777dd4f6f5301d474c97a06c
Author: Michal Nazarewicz <m.nazarewicz@samsung.com>
Date:   Mon Jun 21 13:57:09 2010 +0200

USB: gadget: f_mass_storage: added eject callback

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marek.vasut@gmail.com>
2013-03-18 18:58:53 +01:00
Lukasz Majewski
dee1d99973 usb:composite: USB Mass Storage - storage_common.c from Linux kernel
The storage_common.c source file from v2.6.36 Linux kernel.

commit d26a6aa08b9f12b44fb1ee65625e7480d3d5bb81
Author: Michal Nazarewicz <m.nazarewicz@samsung.com>
Date:   Mon Nov 9 14:15:23 2009 +0100

USB: g_mass_storage: code cleaned up and comments updated

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marek.vasut@gmail.com>
2013-03-18 18:58:53 +01:00
Lukasz Majewski
f7b4162eb1 usb:composite:fix Provide function data when addressing device with only one interface
This commit fixes problems with some non-standard requests send with
device address instead of interface address (bmRequestType.Receipent field).

This happens with dfu-util (debian version: 0.5), which address non standard
requests (like w_value=0x21 and bRequest=GET_DESCRIPTOR) to device.
Without this fix, the above request is STALLED, and hence causes dfu-util
to assume some standard configuration (packet size = 1024B instead of 4096B)
In turn it displays following errors:
Error obtaining DFU functional descriptor
Warning: Assuming DFU version 1.0
Warning: Transfer size can not be detected
...
Warning: Trying default transfer size 1024

This fix allows passing non-standard request to function setup code, where
it shall be handled.

Tested at: 	Trats (exynos4210)
Tested with:DFU and UMS gadgets

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2013-03-18 18:58:52 +01:00
Vipin Kumar
39fd6342a4 usb/host/ehci: Add support for EHCI on spear
Add EHCI support for spear boards

Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
2013-03-16 21:12:02 +01:00
Pantelis Antoniou
a04983d6a9 usb: Fix bug when both DFU & ETHER are defined
When both CONFIG_USB_GADGET & CONFIG_USB_ETHER are defined
the makefile links objects twice.

This patch uses a Makefile specific idiom of
'if defined(CONFIG_USB_GADGET) || defined(CONFIG_USB_ETHER)'
to handle the case.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-03-16 21:12:02 +01:00
Pantelis Antoniou
80eb1bd02d dfu: Properly zero out timeout value
Zero out timeout value; letting it filled with undefined values
ends up with the dfu host hanging.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-03-16 21:12:01 +01:00
Vincent Palatin
2982837e36 usb: ehci: Add 64-bit controller support
On EHCI controller with 64-bit address space support, we must initialize
properly the high word for the PCI bus master accesses.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-16 21:12:01 +01:00
Vincent Palatin
7c38e90aff usb: ehci: generic PCI support
Instead of hardcoding the PCI IDs on the USB controller, use the PCI
class to detect them.

Ensure the busmaster bit is properly set in the PCI configuration.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-16 21:12:01 +01:00
Albert ARIBAUD
b27673ccbd Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2013-03-15 20:50:43 +01:00
Lucas Stach
d7a55e1a4b tegra: usb: move [start|stop]_port into ehci_hcd_[init|stop]
The ehci_hcd entry points were just calling into the Tegra USB
functions. Now that they are in the same file we can just move over the
implementation.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14 11:06:41 -07:00
Lucas Stach
7ae18f3725 tegra: usb: move implementation into right directory
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.

v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14 11:06:41 -07:00
Marek Vasut
afa8721099 mxs: Make ehci-mxs multiport capable
Rework ehci-mxs so it supports both ports on MX28. It was necessary
to wrap the per-port configuration into struct ehci_mxs_port and pull
out the clock configuration function.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-03-07 17:22:57 +01:00
Marek Vasut
47f1331506 mxs: Squash the header file usage in ehci-mxs
The ehci-mxs driver included the register definitions directly.
Use imx-regs.h instead since it contains proper handling of the
differences between mx23 and mx28.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-03-07 17:22:57 +01:00
Stefano Babic
62db0b3d62 USB: drop unneeded header in ehci-mx6
Including header for pads is not needed and breaks board
after renaming pin definitions.

Series-to: u-boot

Series-cc: marex@denx.de,fabio.estevam@freescale.com,eric.nelson@boundarydevices.com

Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-03-07 16:43:47 +01:00