CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.
This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.
We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The type should be int, not u8. cfg->wp_enable will finally be
assigned to priv->wp_enable whose type is int.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
This module can be found on the Turris Omnia board connected
via the I2C interface.
Among some cryptographic functions, the chip has a 512 bit
One Time Programmable memory, 88 byte configuration memory
and 512 byte general purpose memory.
The Turris Omnia stores serial number and device MAC address in
the OTP memory.
This commit adds basic support for reading the EEPROM and also
exposes the chips Random Number Generator.
The driver is based on code by
Josh Datko, Cryptotronix, jbd@cryptotronix.com
and also
Tomas Hlavacek, CZ.NIC, tomas.hlavacek@nic.cz
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 drivers/misc/atsha204a-i2c.c
create mode 100644 include/atsha204a-i2c.h
Signed-off-by: Stefan Roese <sr@denx.de>
When CONFIG_CMD_FASTBOOT or CONFIG_USB_FUNCTION_FASTBOOT are defined
in am335x_evm.h, a dependency on g_dnl.c is created. This in turn
creates a dependency on having USB gadget enabled.
As a result we can't create configs with USB gadget disabled.
Since these CONFIG_ variables are now part of kconfig, move them to
the board defconfigs, and out of am335x_evm.h. This both preserves
current defaults, and allows creating configs with USB gadget off.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make make nand_info array static, since all direct users of nand_info array
have been converted to use get_nand_dev_by_index() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
nand_info is used all over the file so abstract it with
get_nand_dev_by_index() which will help for DM conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This function returns the pointer to the value of a node property.
The current name ofnode_read_prop() is confusing. Follow the naming
of_get_property() from Linux.
The return type (const u32 *) is wrong. DT property values can be
strings as well as integers. This is why of_get_property/fdt_getprop
returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The of_n_addr_cells() and of_n_size_cells() functions are useful for
getting the size of addresses in a node, but in a few places U-Boot needs
to obtain the actual property value for a node without walking up the
stack. Add functions for this and just the existing code to use it.
Add a comment to the existing ofnode functions which do not do the right
thing with a flat tree.
This fixes a problem reading PCI addresses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
This function allows a device's status to be read. This indicates whether
the device should be enabled or disabled.
Note: In normal operation disabled devices will not be present in the
driver-model tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Add a function which reads resources from a device, such as the device
hardware address. This uses the "reg" property in the device.
Unlike other functions there is little sense in inlining this when
livetree is not being used because it has some logic in it and this would
just bloat the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
This provides a way to find the number of strings in a string list. Add it
and also fix up the comment for ofnode_read_string_index().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Enable the pre-console buffer, displaying the model and post-relocation
console announce on sandbox. Also add a model name to the device tree.
This allows testing of these features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
At present the U-Boot banner is only displayed on the serial console. If
this is not visible to the user, the banner does not show. Some devices
have a video display which can usefully display this information.
Add a banner which is printed after relocation only on non-serial devices
if CONFIG_DISPLAY_BOARDINFO_LATE is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Move the display options code into a separate function so that the U-Boot
banner can be obtained from other code. Adjust the 'version' command to
use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Some AHCI drivers use SCSI under the hood. Rather than making the AHCI
driver be in the SCSI uclass it makes sense to have the AHCI device create
a SCSI device as a child. That way we can handle any AHCI-specific
operations rather than trying to pretend tha the device is just SCSI.
To handle this we need to provide a way for AHCI drivers to bind a SCSI
device as its child, and probe it. Add functions for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Split out the code that scans a single SCSI bus into a separate function.
This will allow it to be used from driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The SCSI uclass currently has no operations. It just uses the global SCSI
functions. Fix this by adding operations to the only two drivers that use
the uclass, and replacing the global functions with those defined locally
in the SCSI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With driver model these functions need a device pointer. Add one even
when CONFIG_DM_SCSI is not defined. This avoids having ugly conditional
function prototypes, When CONFIG_DM_SCSI is not defined we can just ignore
the pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add operations for SCSI. These are not yet implemented, but we have the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With driver model we cannot have static data or assume that there is only
one device of each time. Adjust the code so that 'probe_ent' is not needed
with driver model. Add a new ahci_init_dm() function which can init AHCI
for driver model without re-allocating the uclass data. Move over the only
existing driver to use this new function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Two AHCI drivers use SCSI with CONFIG_DM_SCSI. The SCSI uclass calls
scsi_low_level_init() which is implemented by ahci.c. If
CONFIG_SCSI_AHCI_PLAT is defined it does one thing and if it is not
it does something else.
We don't need to call through scsi_low_level_init() to get the init
completed. Instead, adjust the two drivers to call into AHCI directly.
Drop the post-probe init in the SCSI uclass. This means that driver model
doesn't need to use scsi_low_level_init(). It is a legacy function and
driver model should use a driver's probe() method instead.
While we are here, add a comment to the top of the file explaining what
ahci.c does.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This array relates to the AHCI controller so should be exist out on its
own in the file. Move it into the structure. Adjust functions that need
access to this to take the structure as a parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not a very useful name since once it is probed it still hangs
around. With driver model we will use uclass data for this, so rename the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should not be using typedefs in U-Boot and 'ccb' is a pretty short
name. It is also used with variables. Drop the typedef and use 'struct'
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This name should be lower case. Also the _block suffix is superfluous.
Rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Put the driver-model declarations first since we are migrating to that.
Also drop scsi_init() when driver model is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is only defined by one driver and is empty. Move it into
the SCSI implementation itself. We could remove it, but it should be
useful for debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sometimes it is useful to iterate through all devices in a uclass and
skip over those which do not work correctly (e.g fail to probe). Add two
new functions to provide this feature.
The caller must check the return value each time to make sure that the
device is valid. But the device pointer is always returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some tests which check the behaviour of uclass_first_device() and
uclass_next_device() when probing of a device fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK818 PMIC contains a charger. Add very basic charger functionality
to be able to regulate the USB input current and charger shutdown limits.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change migrates the USB_DWC2 configuration item to Kconfig
and runs moveconfig to adjust header files and defconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Split off into a separate patch:
Ran moveconfig to migrate other boards:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable soc support for SPL and U-boot skeleton.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There are some functions like sdram_size_mb can be re-used for
different rockchip SoCs, just put them into common file.
Add board_get_usable_ram_top() for ram_top init base on
SDRAM_MAX_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added SDRAM_MAX_SIZE definition for RK3036:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
fixup: 3036 fix for sdram_common
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Runtime U-boot dtb selection is generally a two step process. First step
is to simply use an initial generic dtb. The second step is to select
the dtb and perhaps execute additional code ones U-boot knows what board
it is running on. Embedded_dtb_select handles the second step by allowing
board specific code to run and perform what ever necessary configuration
that is needed.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some platforms may append a FIT image to the U-boot image. This function
aids in parsing the FIT image and selecting the correct DTB at runtime.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of the functions within spl_fit will be used for non spl purposes.
Instead of duplicating functions simply break the functions to be reused
into its own file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Only add the new define to image.h, otherwise we see breakage
due to massive include leakage into host tools in some cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
CS Systemes d'Information (CSSI) manufactures 8xx boards for
critical communication systems. Those boards have been
running U-Boot since 2010 and will have to be maintained
until at least 2027.
commit 5b8e76c35e
("powerpc, 8xx: remove support for 8xx") orphaned those boards
by removing support for the mpc8xx CPU.
This commit partially restores support for the 8xx, with the
following limitations:
- Restores support for MPC866 and MPC885 only
- Does not restore IDE, PCMCIA, I2C, USB
- Does not restore examples
- Does not restore POST
- Does not restore Ethernet on SCC
- Does not restore console on SCC
- Does not restore bedbug and kgdb support
As the 866 and 885 do not support the following features,
they are not restored either:
- VIDEO / LCD
- RTC clock
The CPM uCODE patch is not restored either, because:
- 866 and 885 already have support for I2C and SPI relocation
without a uCODE patch
- relocation of SMC, I2C or SPI is only needed for using SCCs
for Ethernet or QMC
The dynamic setup/calculation of clocks is removed, we
expect the target being use with the clock and PLPRCR register
defined in the configuration.
All the clock settings for 8xx prior to 866 is removed as
well as we now only support 866 and 885.
This code is mature and addresses mature boards. Therefore
all code enclosed in '#if 0/#endif' and '#if XX_DEBUG/#endif'
is unneeded.
The following files are not restored by this patch:
- arch/powerpc/cpu/mpc8xx/bedbug_860.c
- arch/powerpc/cpu/mpc8xx/fec.h
- arch/powerpc/cpu/mpc8xx/kgdb.S
- arch/powerpc/cpu/mpc8xx/plprcr_write.S
- arch/powerpc/cpu/mpc8xx/scc.c
- arch/powerpc/cpu/mpc8xx/upatch.c
- arch/powerpc/cpu/mpc8xx/video.c
- arch/powerpc/include/asm/status_led.h
- arch/powerpc/lib/ide.c
- arch/powerpc/lib/ide.h
- doc/README.MPC866
- drivers/pcmcia/mpc8xx_pcmcia.c
- drivers/rtc/mpc8xx.c
- drivers/usb/gadget/mpc8xx_udc.c
- drivers/video/mpc8xx_lcd.c
- examples/standalone/test_burst.c
- examples/standalone/test_burst.h
- examples/standalone/test_burst_lib.S
- examples/standalone/timer.c
- include/mpc823_lcd.h
- include/usb/mpc8xx_udc.h
- post/cpu/mpc8xx/Makefile
- post/cpu/mpc8xx/cache.c
- post/cpu/mpc8xx/cache_8xx.S
- post/cpu/mpc8xx/ether.c
- post/cpu/mpc8xx/spr.c
- post/cpu/mpc8xx/uart.c
- post/cpu/mpc8xx/usb.c
- post/cpu/mpc8xx/watchdog.c
Some of the restored files are not located in a proper location.
In order to keep traceability of the changes, they will be
moved to their correct location and moved to Kconfig in a
followup patch.
This patch also declares CSSI as point of contact for the update
of the 8xx platform, as those boards are the only ones still
being maintained on the 8xx area. A later patch will add
those boards to the tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brppt1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
There is no need to duplicate same option with different name.
Kill HW_WATCHDOG_TIMEOUT_MS in favor of WATCHDOG_TIMEOUT_MSECS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add missing static to serial_stub_puts().
Unexport serial_stub_{getc,tstc} because they are used locally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Highlights this time: bugfixes. With these changes, OpenBSD should
be more happy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TXN1
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2017-07-04
Highlights this time: bugfixes. With these changes, OpenBSD should
be more happy.
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
The UEFI specification states that the tpl, function and context
arguments are to be ignored if neither EVT_NOTIFY_WAIT or
EVT_NOTIFY_SIGNAL are specified. This matches observed behaviour with
an AMI EDK2 based UEFI implementation.
Skip calling the notify function if neither flag is present.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Acked-By: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Discern the SoMs based on the presence of SPI flash to support both
variants of the SoM, one booting from SPI NOR and one booting from
eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The redesigned version of the SoM which was released onto the market
does no longer contain SPI flash, but boots from the eMMC. Move the
environment storage to the eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SoM has been redesigned to work around bug in the SoC and is now
capable of booting from the eMMC. Add support for booting from eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SDHCI1 is the primary boot controller on rev. 2.1 SoM, which
is the version available on the market. Swap the controller order
to match this and future versions of the SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Enable DFU and USB mass storage support for the DENX MA5D4 SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With deprecation of I2C EEPROM we we left without a permamnent
storage for U-Boot environment, but luckily we may simply use SD-card
with FAT partition for that.
Having environment on SD-card is much more convenient as it
allows us to preserve all the settings when moving from one board to
another. Moreover instead of 256 bytes of EEPROM we're now virtually
unlimited in stuff being placed in environment like complicated scripts
etc which are usually required in case of full-scale distros.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With eb5ba3aefd "i2c: Drop use of CONFIG_I2C_HARD" in place we
cannot use I2C EEPROM any longer so we're dropping all references to
both EEPROM and I2C which was only used for EEPROM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL_MAX_SIZE is the internal memory size minux the space
used by bootrom.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As all x86 boards have been switched over to use DM USB, remove
CONFIG_USB_MAX_CONTROLLER_COUNT which is not used by DM USB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Decrease malloc size to 1MB from 256MB. Huge malloc
space is adding huge delay in mem_malloc_init() because
we are enabling CONFIG_SYS_MALLOC_CLEAR_ON_INIT
which clear the whole malloc space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CPU_RELEASE_ADDR is used only when CONFIG_ARMV8_MULTIENTRY
is enabled. ZynqMP is running ATF which takes care about this
that's why no need to have this macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
To prevent possible double inclusions in future.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For better readability and setup-handling we refactor the default
environment.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This define isn't used anymore in the u-boot source tree, so we drop it
from the config header.
We drop it also from the 'config_whitelist.txt'
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
the BMP logo loading has become obsolete and is not used any more. So we
drop the support for it.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brxre1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The terminator endif of ifdef _NAND_H_ should be at the
end of file as a fail safe.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
Use eMMC (instead of SD card) to store U-Boot environment. Use
"reserved" partition for U-Boot environment.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).
[1] 7a53a1a811 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).
[1] 7a53a1a811 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
When we don't have CONFIG_BLK defined we don't have a forward
declaration of struct udevice, and thus get a warning about it on
blk_get_from_parent(), which we only have when CONFIG_BLK is set. Move
the declaration of blk_get_from_parent() to be with the other CONFIG_BLK
parts.
Fixes 9f103b9cb5 ("dm: blk: Add a way to obtain a block device from ...")
Signed-off-by: Tom Rini <trini@konsulko.com>
As only FIT image is supported now, this patch is to support loading
32-bit uImage, dtb and rootfs separately.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
Signed-off-by: Tom Rini <trini@konsulko.com>
At present CP15 init is disabled on tegra. Use the correct option so that
this init is performed on boot. This enables the instruction cache, for
example, which is critical to the machine running at full speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is some inconsistency between uses of CONFIG_RTC_DS13xx and
CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from
these variables.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
The addresses of the registers in TI TPS65217 are not continuous.
There is a gap between ENABLE(0x16) and DEFUVLO(0x18). No 0x17
register available.
Fixup the enum values by adding a 'reserved' placeholder to correct
the addresses higher than 0x17.
Series-to: Heiko Schocher <hs@denx.de>
Signed-off-by: Brock Zheng Techyauld Ltd <yzheng@techyauld.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add support to bind the regulators/child nodes with the pmic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Many devices support a child block device (e.g. MMC, USB). Add a
convenient way to get this device given the parent device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
With video output support for the RK3399-Q7 (Puma) available, we want
CMD_BMP enabled and the support for 16bit, 24bit and 32bit BMPs
defined.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- enable SYS_WHITE_ON_BLACK via defconfig
Reviewed-by: Simon Glass <sjg@chromium.org>
The regs_otg field in uintptr_t of the platform data structure for
dwc2-otg has thus far been an unsigned int, but will eventually be
casted into a void*.
This raises the following error with GCC 6.3 and buildman:
../drivers/usb/gadget/dwc2_udc_otg.c: In function 'dwc2_udc_probe':
../drivers/usb/gadget/dwc2_udc_otg.c:821:8: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
reg = (struct dwc2_usbotg_reg *)pdata->regs_otg;
^
This changes regs_otg to a uintptr_t to ensure that it is large enough
to hold any valid pointer (and fix the associated warning).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RV1108 is embedded with an ARM Cortex-A7 single core and a DSP core
from Rockchip. It is designed for varies application scenario such
as car DVR, sports DV, secure camera and UAV camera.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add config of max root ports and add config to enable xhci
controller.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add defconfig for usb and ehci and ohci controller, config maximal
number of ports of the root hub for ohci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our efuse driver for the RK3399 ready, we can add the
board-specific code that consumes the cpuid from the efuse block and
postprocesses it into the system serial (using the same CRC32 based
derivation as in Linux).
We expose the cpuid via two distinct environment variables:
serial# - the serial number, as derived in Linux
cpuid# - the raw 16 byte CPU id field from the fuse block
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels
Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
At present bootstage only supports U-Boot proper. But SPL can also consume
boot time so it is useful to have the record start there.
Add bootstage support to SPL. Also support stashing the timing information
when SPL finishes so that it can be picked up and reported by U-Boot
proper. This provides a full boot time record, excluding only the time
taken by the boot ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a few places that should use const *, such as
bootstage_unstash(). Update these to make it clearer when parameters are
changed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should return a proper error number instead of just -1. This helps the
caller to determine what when wrong. Update a few functions to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards cannot access pre-relocation data after relocation. Reserve
space for this and copy it during preparation for relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are several code style and comment nits. Fix them and also remove
the comment about passing bootstage to the kernel being TBD. This is
already supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage uses the data section of the image to store its
information. There are a few problems with this:
- It does not work on all boards (e.g. those which run from flash before
relocation)
- Allocated strings still point back to the pre-relocation data after
relocation
Now that U-Boot has a pre-relocation malloc() we can use this instead,
with a pointer to the data in global_data. Update bootstage to do this and
set up an init routine to allocate the memory.
Now that we have a real init function, we can drop the fake 'reset' record
and add a normal one instead.
Note that part of the problem with allocated strings remains. They are
reallocated but this will only work where pre-relocation memory is
accessible after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we provide a default version of this function for use by
bootstage. However it uses the system timer and therefore likely requires
driver model. This makes it impossible to time driver-model init.
Drop the function and require boards to provide their own. Add a sandbox
version also. There is a default implememtation in lib/time.c for boards
which use CONFIG_SYS_TIMER_COUNTER.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SD card automatic installation system depends on the default
environment of the previous U-Boot.
Add the missing environment variables.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Supported boot devices are raw QSPI and raw SD card.
Add support for a FAT16/32 file system for SD card.
The SOC's boot ROM only supports FAT file system.
Therefore remove the SPL support for the EXT file system.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Instead, use
the asm/hardware.h header to provide the required declarations, and drop
the common.h changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These declarations should not be in common. Remove those that are not
needed and move the others to an arch-specific location.
Signed-off-by: Simon Glass <sjg@chromium.org>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Set up a new asm/ppc.h header file to hold this arch-specific stuff. It
should not be in common.h. It probably should be refactored to use
asm/arch instead, but that is a job for the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
With a small tweak we can avoid including these files for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not actually needed anywhere, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than including this arch-specific header file in common.h, include
it from within nds32's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within mips's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than including this arch-specific header file in common.h, include
it from within arm's u-boot.h header.
Also drop the comment about something to be fixed. It has been there
forever and it is not clear what it means.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within x86's u-boot.h header.
Also drop the comment about something to be fixed. It is not clear what
needs fixing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within sandbox's u-boot.h header.
Also drop the comment about something to be fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within arc's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add fallbacks needed to keep all boards building
while they are migrated to use Kconfig symbols
instead of defines in <board>_config.h files for
FAT filesystem.
These should eventually go away once Kconfig select
or imply statements are put in place and duplicated
defines in <board>_config.h removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[trini: Update logic since CMD_FAT / CONFIG_SPL_FAT_SUPPORT are
selecting FS_FAT]
Signed-off-by: Tom Rini <trini@konsulko.com>
