Now that there is only one sequence number (rather than both requested and
assigned ones) we can simplify this function. Also update its caller to
simplify the logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new sequence number in all cases. Drop the rockchip case because
the sequence number should be 0 anyway, and assigning to the sequence
number is not permitted.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPI Flash controller driver for Cortina Access
CAxxxx SoCs
Signed-off-by: Pengpeng Chen <pengpeng.chen@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Vignesh R <vigneshr@ti.com>
CC: Tom Rini <trini@konsulko.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The designware ssi device has "broken" chip select behaviour [1], and needs
specific manipulation to use the built-in chip select. The existing fix is
to use an external GPIO for chip select, but typically the K210 has SPI3
directly connected to a flash chip with dedicated pins. This makes it
impossible to use the spi_xfer function to use spi, since the CS is
de-asserted in between calls. This patch adds an implementation of
exec_op, which gives correct behaviour when reading/writing spi flash.
This patch also rearranges the headers to conform to U-Boot style.
[1] https://lkml.org/lkml/2015/12/23/132
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
CTRLR0 can have several different layouts depending on the specific device
(dw-apb-ssi vs dwc-ssi), and specific parameters set during synthesis.
Update the driver to support three specific configurations: dw-apb-ssi with
SSI_MAX_XFER_SIZE=16, dw-apb-ssi with SSI_MAX_XFER_SIZE=32, and dwc-ssi.
dw-apb-ssi is the version of the device on Altera/Intel SoCFPGAs, MSCC
SoCs, and Canaan Kendryte K210 SoCs. This is the only version this driver
supported before this change. The register layout before version 3.23a is:
| 31 .. 16 |
| other stuff |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS |
Note that DFS (Data Frame Size) is only 4 bits, limiting transfers to data
frames of 16 bits or less.
In version 3.23a, the SSI_MAX_XFER_SIZE parameter was introduced. This
parameter defaults to 16 (resulting in the same layout as prior versions),
but may also be set to 32. To allow setting longer data frame sizes, a new
DFS_32 register was introduced:
| 31 .. 21 | 20 .. 16 |
| other stuff | DFS_32 |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | all zeros |
The old DFS field no longer controls the data frame size. To detect this
layout, we try writing 0xF to DFS. If we read back 0x0, then this device
has SSI_MAX_XFER_SIZE=32.
dwc-ssi is the version of the device on Intel Keem Bay SoCs and Canaan
Kendryte K210 SoCs. The layout of ctrlr0 is:
| 31 .. 16 |
| other stuff |
| 15 .. 12 | 11 .. 10 | 9 .. 8 | 7 .. 6 | 4 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS_32 |
The semantics of the fields have not changed since the previous version.
However, SSI_MAX_XFER_SIZE is effectively always 32.
To support these different layouts, we model our approach on the one
which the Linux kernel has taken. During probe, the driver calls an init
function stored in driver_data. This init function is responsible for
determining the layout of CTRLR0, and supplying the update_cr0 function.
The style of and information behind this commit is based on the Linux MMIO
driver for these devices. Specific reference was made to the series adding
support for Intel Keem Bay SoCs [1].
[1] https://lore.kernel.org/linux-spi/20200505130618.554-1-wan.ahmad.zainie.wan.mohamad@intel.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This should reduce the size of the struct, and also groups more similar
fields together.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A few registers had slightly different names from what is in the datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using an fdt-specific function causes problems when compiled with a live
tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Define LOG_CATEGORY and change printf and pr_*
to dev_ (when dev is available) or log_ macro.
This patch adds the support of logging feature with log command
(filtering, display of device name in trace) and allows to
suppress traces via the syslog driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Fix up the code style for those declarations that should now fit onto one
line, which is all of them that currently do not.
This is needed for dtoc to detect the structs correctly, at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, enabling CONFIG_APL_SPI_FLASH_BOOT does not build since SPI
and SPI flash are not enabled for TPL. Add a condition to fix this and
tidy up a build warning in the SPI-flash driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add function description for zynq_qspi_init_hw and zynq_qspi_chipselect.
Fix zqspi to priv in function descriptions.
Change the description of priv as pointer to zynq_qspi_priv structure.
Fix other function descriptions to kernel-doc style.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove fixed reference clk used by plat->frequency and use clk
subsystem to get reference clk. As per spi dt bindings
"spi-max-frequency" property should be used by the slave devices.
This property is read by spi-uclass driver for the slave device.
So avoid reading above property from the platform driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove fixed reference clk used by plat->frequency and use clk
subsystem to get reference clk. As per spi dt bindings
"spi-max-frequency" property should be used by the slave devices.
This property is read by spi-uclass driver for the slave device.
So avoid reading above property from the platform driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unused variable 'count' which is causing warning while
compilation.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add fallback compatibility string for R-Car Gen3 and RZ/G2.
Also sorted the compatible string as per SoC ID.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Octeon TX2 sets the TB100_EN bit in the config register. We need to use
a fixed 100MHz clock for this as well to work properly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
commit 71ba2cb0d6 ("board: stm32mp1: correct CONFIG_IS_ENABLED usage for LED")
commit a5ada25e42 ("rockchip: clk: fix wrong CONFIG_IS_ENABLED handling")
commit 5daf6e56d3 ("common: console: Fix duplicated CONFIG in silent env callback")
commit 48bfc31b64 ("MIPS: bootm: Fix broken boot_env_legacy codepath")
Fix all files found by `git grep "CONFIG_IS_ENABLED(CONFIG"` by running
':%s/CONFIG_IS_ENABLED(CONFIG_\(\w+\))/CONFIG_IS_ENABLED(\1)/g' in vim.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree has a way to specify GPIO lines as chip selects. From
the binding docs:
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use `bus` instead of `dev`.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke,
I'm guessing due to this hunk
@@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags)
if (ret)
return ret;
+ /* combine the requested flags (for IN/OUT) and the descriptor flags */
+ flags |= desc->flags;
ret = _dm_gpio_set_dir_flags(desc, flags);
from commit 695e5fd546 ("gpio: update dir_flags management"). But
the blame is mostly on the driver itself which seems rather confused:
The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in
each activate/deactivate, dm_gpio_set_dir_flags() is called with
merely GPIOD_IS_OUT, and then the driver call set_value(0) for
activate.
That used to work, but with the above hunk, the ACTIVE_LOW setting
from the request becomes persistent, so the gpio driver ends up being
asked to set the value to 1 in mpc8xxx_spi_cs_activate().
So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate
functions, and use a value of 1 to mean "logically enabled".
Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the
request and make it up to the list of gpio cs in DT to indicate
whether that CS is enabled when driven low (as is of course usually
the case), but that requires changing
arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't
have that hardware to test on. I have, however, tested our
own (mpc8309-based) hardware with this change, and I have also tested
that removing the GPIOD_ACTIVE_LOW from the request and updating our
DT as
- gpios = <&spisel 0 0>;
+ gpios = <&spisel 0 GPIO_ACTIVE_LOW>;
still works.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add an ofdata_to_platdata() callback to access dts in U-boot and
access all platform data in it. This prepares the driver for supporting
both device tree as well as static platform data structures in SPL.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
There are devices which don't use OF_CONTROL or OF_PLATDATA but instead
rely on statically defined platdata. Block dm_scan_fdt_dev() with both
configs to avoid build failures under this condition.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adds support for SPI controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After latest improvements on OF_PLATDATA struct names are generated
based on driver name instead of compatible strings. With this in mind,
using aliases in drivers are not longer needed.
This patch removes code that tried to handle these kind of aliases to
improve readability.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Communication with some SPI slaves just won't cut it if these delays
(before the beginning, and after the end of a transfer) are not added to
the Chip Select signal.
These are a straight copy from Linux:
Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
drivers/spi/spi-fsl-dspi.c
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for the RK3328 SPI controller
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
For many device types it is possible to figure out the name just by
looking at its uclass or parent. Add a function to handle this, since it
allows us to cover the vast majority of cases automatically.
However it is sometimes impossible to figure out an ACPI name for a device
just by looking at its uclass. For example a touch device may have a
vendor-specific name. Add a new "acpi,name" property to allow a custom
name to be created.
With this new feature we can drop the get_name() methods in the sandbox
I2C and SPI drivers. They were only added for testing purposes. Update the
tests to use the new values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to write a SPI descriptor to the generated ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
i.MX platforms provide large AHB mapped space for QSPI, each
controller has 256MB. However, current driver only maps small
size (AHB buffer size) of AHB space, this implementation
causes i.MX failed to boot M4 with QSPI XIP image.
Add config CONFIG_FSL_QSPI_AHB_FULL_MAP (default enabled for i.MX)
to address above problem.
When the config is set:
1. Full AHB space is divided to each CS.
2. A dedicated LUT entry is used for AHB read only.
3. The MODE instruction in LUT is replaced to standard ADDR instruction
4. The address in spi_mem_op is used to SFAR and AHB read
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Add compatible string and driver data for i.MX7ULP.
Meanwhile, the address set to SFA1AD/SFA2AD/SFB1AD/SFB2AD should
align with 1KB, because the lowest 10 bits are reserved by the
registers definition.
For i.MX7ULP which has only 128Bytes AHB buffer, must align it
when setting the registers and selecting cs.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Drop the nondm code from kirkwood_spi.c since there
is no board or any other code using for it.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
The spi bitbanging driver did not implement all spi modes properly. Add
code to support all spi modes, honoring soft_spi_set_mode() and
defaulting to spi mode 0. Previously, CPHA was implemented inversely
(defaulting to CPHA=1) and CPOL=1 was hardcoded.
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Remove below config options and convert them to macros. They have never
been configured to different values than default one. And also it makes
sense to reduce the config_whitelist.
CONFIG_SYS_ZYNQ_SPI_WAIT
CONFIG_SYS_ZYNQ_QSPI_WAIT
CONFIG_XILINX_SPI_IDLE_VAL
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
atmel spi driver now accessible only when DM_SPI enabled.
So, remove nondm code.
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Deadline for DM migration already passed by months.
- Sent couple of zap patches and
- No response on dm conversation
hence removed the driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Order the macros, private structures and simple functions
in a proper way to have more code readability.
No functionality changed.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Deadline for DM migration already passed by months
and no response on full dm conversation hence removed
the nondm code.
Note: Look like there is no user for nondm code
for this driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
At present this logic does not work on link and samus, since their SPI
controller is not a PCI device, but a child of the PCH.
Unfortunately, fixing this involves a lot of extra logic. Still, this was
requested in the review of the fix-up patch, so here it is.
Fixes: 92842147c3 ("spi: ich: Add support for get_mmap() method")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> (on Intel minnowmax)
sh_spi driver is deprecated, no active updates and
no board user, hence dropped the same.
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
CF_SPI kconfig option defined twice with DM_SPI
and non DM_SPI.
Drop the non DM_SPI side kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Board gets reset when performing burst read/write operations. On the
other hand, no such behaviour is observed on small size operations.
In Linux, readl_poll_timeout API already adds delay of 1us which is
further skipped in U-boot. Hence, use new "readl_poll_sleep_timeout" API
which adds delay alongwith timeout functionality.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The guessed reason is that the existing logic of filling
tx fifo with data, rx fifo with NULL for tx transfer and
filling rx fifo with data, tx fifo with NULL for rx transfer
is not clear enough to support the Quad Page Program.
SiFive SPI controllers have specific sets of watermark
registers and SPI I/O directions bits in order to program
SPI controllers clear enough to support all sets of operating
modes.
Here is the exact programing sequence that would follow on this
patch and tested via SPI-NOR and MMC_SPI.
- set the frame format proto, endian
- set the frame format dir, set it for tx and clear it for rx
- TX transfer:
fill tx fifo with data.
wait for TX watermark bit to clear.
- RX transfer:
fill tx fifo with 0xff.
write nbytes to rx watermark register
wait for rx watermark bit to clear.
read the rx fifo data.
So, this patch adopts this program sequence and fixes the existing
I/O direction bit.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller has a proto bit field in frame format
register which would be used to configure the SPI I/O protocol
lines used on specific transfer.
Right now the driver is configuring this proto using slave->mode,
for all types of transctions. This makes the driver unable to
function since the proto needs to configure dynamically for
each and every transaction separately at runtime.
Now, the controller driver supports per transfer via spi-mem
exec_opo, so add the fmt_proto flag and fill the per transfer
buswidth so that the controller configures the proto bit at
runtime.
This patch fixes the SPI controller works with SPI NOR flash
on quad read with page program.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller is responsible to handle the
slave devices like mmc spi and spi nor flash.
The controller is designed such a way that it would
handle the slave transactions based on the I/O protocol
numbers, example if spi nor slave send quad write opcode
it has to send alone with I/O protocol number of 4 and
if it try to send data it has to send I/O protocol number
along with 4 line data.
But the current spi-xfer code from spi-mem is combining
the opcode and address in a single transaction, so the
SPI controller will be unable to identify the I/O protocol
number of opcode vs address.
So, add the spi-mem exec_op with spi-xfer of opcode, address
and data as a separate transaction. This doesn't remove
the .xfer of dm_spi_ops since mmc spi will make use of it.
Note: This code might have moved to the spi-mem core area
once we have done the dedicated tests on other controllers
and have real reason to move.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Usually variable name slave is used for spi_slave structure
and slave_plat for the dm_spi_slave_platdata.
Let's follow this meaningful notation by replacing slave
with slave_plat for dm_spi_slave_platdata structure.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit: 0ebb261a0b2d ("spi: spi-mem: Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum")
in linux.
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
This also fixes a bug identified with the atmel-quaspi driver.
The spi-nor core, when erasing sectors, fills the spi_mem_op template
using SPI_MEM_OP_NO_DATA, which initializes all the data members with
value zero. This is wrong because data.dir is treated as SPI_MEM_DATA_IN,
which translates in our driver to read accesses for erases (RICR), while
the controller expects write accesses (WICR).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.
Tested on u-boot-ti/next.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To support the SPI MEM API, instead of modifying the existing U-Boot
driver, this patch adds a port of the existing Linux driver.
This also has the advantage that porting changes and fixes from Linux will
be easier.
Porting of driver left most of the functions unchanged while few of the
changes are:
-Remove lock(mutexes) and irq handler as u-boot is a single core execution.
-Remove invalid masterid as it was required specially for multicore
execution in LS2088ARDB which is not the case in u-boot.
-Remove clock support as changing spi speed is not supported in uboot and
nor in linux.
Currently tested on LS1088ARDB, LS1012ARDB, LS1046ARDB, LS1046AFRWY,
LS1043AQDS, LS1021ATWR, LS2088ARDB, I.MX6ULL EVK.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The build currently fails with
drivers/spi/mpc8xxx_spi.c:64:3: warning: implicit declaration of function ‘dev_err’ [-Wimplicit-function-declaration]
...
drivers/spi/built-in.o: In function `mpc8xxx_spi_set_speed':
drivers/spi/mpc8xxx_spi.c:227: undefined reference to `dev_err'
Fixes: 4856cc7a97 (mpc8xxx_spi: implement real ->set_speed)
Fixes: 1a7b462dee (mpc8xxx_spi: put max_cs to use)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This Tegra QSPI driver hadn't been brought up to date with how
DM drivers are fetching data from the FDT now, and was pulling
in bogus data for base, max freq, etc. Fixed ofdata_to_platdata
to work the same way it does in the tegra114 SPI driver, using
dev_read_ functions.
Signed-off-by: Tom Warren <twarren@nvidia.com>
When claim_bus was setting the clock, it reset the QSPI controller,
which wipes out any tap delays set by previous bootloaders (nvtboot,
CBoot for example on Nano). Instead of doing that in claim_bus, which
gets called a lot, moved clock setting to probe(), and set tap delays
there, too. Also updated clock to 80MHz to match CBoot. Now QSPI env
save works reliably again.
Signed-off-by: Tom Warren <twarren@nvidia.com>
claim_bus() is passed a udevice *dev, which is the bus device's parent.
In this driver, claim_bus assumed it was the bus, which caused the
'priv' info pointer to be wrong, and periph_id was incorrect. This in
turn caused the periph clock call to assign the wrong clock (PLLM
instead of PLLP0), which caused a kernel warning. I only saw the 'bad'
periph_id when enabling DEBUG due to an assert. Not sure how QSPI was
working w/this errant clock, but it was moot as QSPI wasn't active
unless you probed it, and that wasn't happening until I posted a patch
to enable env save to QSPI for Nano (coming soon).
Signed-off-by: Tom Warren <twarren@nvidia.com>
This feature should not be enabled in release but can be useful for
developers who need to monitor register accesses at some specific places.
Helped me identify a bug in u-boot, by comparing the register accesses
from the u-boot driver with the ones from its linux variant.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[jagan: use 16 bit array with tmp variable]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The sama5d2 QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 24c8ff4684 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Not all boards have the same CSB frequency, nor do every SPI slave
necessarily support running at 16.7 MHz. So implement ->set_speed;
that also allows using a smaller PM (i.e., 0) for slaves that do
support a higher speed.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There are a few problems with the current driver.
First, it unconditionally reads from dout/writes to din whether or not
those pointers are NULL. So for example a simple "sf probe" ends up
writing four bytes at address 0:
=> md.l 0x0 8
00000000: 45454545 45454545 05050505 05050505 EEEEEEEE........
00000010: 00000000 00000000 07070707 07070707 ................
=> sf probe 0
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53618 din 00000000 bitlen 8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 0FB536B8 bitlen 48
SF: Detected s25sl032p with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> md.l 0x0 8
00000000: ff000000 45454545 05050505 05050505 ....EEEE........
00000010: 00000000 00000000 07070707 07070707 ................
(here I've change the first debug statement to a printf, and made it
print the din/dout pointers rather than the uints they point at).
Second, as we can also see above, it always writes a full 32 bits,
even if a smaller amount was requested. So for example
=> mw.l $loadaddr 0xaabbccdd 8
=> md.l $loadaddr 8
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
02000010: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x400 6
device 0 offset 0x400, size 0x6
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 48
SF: 6 bytes @ 0x400 Read: OK
=> sf read 0x02000010 0x400 8
device 0 offset 0x400, size 0x8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53848 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000010 bitlen 64
SF: 8 bytes @ 0x400 Read: OK
=> md.l $loadaddr 8
02000000: 45454545 45450000 aabbccdd aabbccdd EEEEEE..........
02000010: 45454545 45454545 aabbccdd aabbccdd EEEEEEEE........
Finally, when the bitlen is 24 mod 32 (e.g. requesting to read 3 or 7
bytes), the last three bytes and up being the wrong ones, since the
driver does a full 32 bit read and then shifts the wrong byte out:
=> mw.l $loadaddr 0xaabbccdd 4
=> md.l $loadaddr 4
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x444 10
device 0 offset 0x444, size 0x10
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 128
SF: 16 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 3031392e 30342d30 U-Boot 2019.04-0
=> mw.l $loadaddr 0xaabbccdd 4
=> sf read $loadaddr 0x444 0xb
device 0 offset 0x444, size 0xb
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 88
SF: 11 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 31392e00 aabbccdd U-Boot 219......
Fix all of that by always using a character size of 8, and reject
transfers that are not a whole number of bytes. While it ends being
more work for the CPU, we're mostly bounded by the speed of the SPI
bus, and we avoid writing to the mode register in every loop.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Currently, max_cs is write-only; it's just set in
mpc8xxx_spi_ofdata_to_platdata and not otherwise used.
My mpc8309 was always resetting during an "sf probe 0". It turns out
dm_gpio_set_dir_flags() was being called with garbage, since nothing
had initialized priv->gpios[0] - our device tree used "cs-gpios"
rather than "gpios", so gpio_request_list_by_name() had returned 0.
That would have been a lot easier to figure out if the chip select
index was sanity checked, so rename max_cs to cs_count, and reject a
xfer with a too large cs index.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
When ich_spi_exec_op_hwseq() is called to erase a 4k block
(opcode = SPINOR_OP_BE_4K), it expects to find a length value in
op->data.nbytes, but that value is always 0. As a result, the while loop
is never executed and no erase is carried out.
Fix this by dropping the loop code entirely, only keeping the relevant
parts of the loop body.
See http://patchwork.ozlabs.org/patch/1222779/ for more detailed
background information and discussion.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
TI's AM654 SoC has a Cadence OSPI IP. Add a new compatible string for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add chip select number check in spi_find_chip_select().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
When two instances of AXI QSPI with flash are added and tested
simultaneously the spi driver operations are relocated twice.
As a result code is accessing addresses outside of RAM when
relocated second time which is causing a crash.
Tested on Microblaze.
Similar change was done in past by:
commit f238b3f0fb ("watchdog: dm: Support manual relocation for watchdogs")
commit 2588f2ddfd ("dm: sf: Add support for all targets which requires MANUAL_RELOC")
commit 1b4c2aa25b ("gpio: dm: Support manual relocation for gpio")
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Note, that the size is further divided into 'minus 1' while writing
into CTRLR1.
This change fixed two different read issues,
1. sf read failure when with > 0x10000
2. Boot from SPI flash failed during spi_flash_read call in
common/spl/spl_spi.c
Observed and Tested in
- Rockpro64 with Gigadevice flash
- ROC-RK3399-PC with Winbond flash
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Apollo Lake to the ICH driver. This involves adjusting the
mmio address and skipping setting of the bbar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In TPL we want to reduce code size and support running with CONFIG_PCI
disabled. Add special code to handle this using a fixed BAR programmed
into the SPI on boot. Also cache the SPI flash to speed up boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add this method so that the memory-mapped location of the SPI flash can
be queried.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Apollo Lake (APL) only supports hardware sequencing. Add support for this
into the SPI driver, as an option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel Fast SPI interface is similar to ICH. Add of-platdata support
for this using the "intel,fast-spi" compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This incorrectly shortens read operations if there is a maximum write size
but no maximum read size. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to store the mmio base in platdata. It reduces the amount of
casting needed. Update the code and move the struct to the C file at the
same time, as we will need to use with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use debug() instead of printf() to reduce code size and change a bool
return value to the use the 'bool' type. Also drop the global data
declaration since it not actually used. Finally, set the log category.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use dev_get_driver_data() to obtain the device type. It has the same
effect and is shorter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reduce the size of the probe function but putting this code into its own
function.
Also remove the assumption that the PCH is always a parent of the SPI
controller, as this is not the case APL platforms. Use driver model to
find the PCH instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is annoying to have some of the init code in a different part of the
file. Move ich_init_controller() to just above probe() to keep things
together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't normally need this on x86 unless the size of SPI flash devices is
larger than 16MB. This can be enabled by particular SoCs as needed, since
it adds to code size.
Drop the default enabling of this option on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have to have an xfer() method even if it does nothing. This
is not correct, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
