Add a directory in drivers/clk to regroup the clock drivers for all
STM32 Soc with CONFIG_ARCH_STM32 (MCUs with cortex M) or
CONFIG_ARCH_STM32MP (MPUs with cortex A).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Acked-by: Sean Anderson <seanga2@gmail.com>
Change-Id: I955af307963f732167396f0157a30cf2fc91f150
Add support of STM32MP13x the ETZPC part of fdt.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: If2777fbf66b8525a2a447056780aaa04e6b0a9a0
Introduce STM32MP15 function and defines to prepare the
STM32MP13 introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: I909b205e73dcf207e0216aae5905c3c52472020e
Add in U-Boot documentation the quick instruction to
setup the STMicroelectronics STM32MP13x boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a initial config for STM32M13x SOC family, using the stm32mp135f-dk
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Although not recommended, the reset property could be made optional.
This way the driver will probe even if no reset property is provided
in an sdmmc node in DT. This reset is already optional in Linux.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add stm32mp15x prefix to all STM32MP15x board specific functions,
this patch is a preliminary step for STM32MP13x support.
This patch also adds the RCC probe to avoid circular access with
usbphyc probe as clk provider.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for "st,stm32mp135-pinctrl" for STM32MP13x
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of several MAC address in OTP (3 32bits OTP word for
2 MAC address) for SOCs in STM32MP13x family: STM32MP133 and STM32MP135.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add config CONFIG_STM32MP15_PWR to handle the
access to regulators managed by the PWR driver defined in
pwr_regulator.c
This driver is only used in U-Boot by STM32MP15x family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add sub Kconfig for each SOC in the STM32 CPU family.
It is a preliminary step to introduce a new SOC in the STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add mandatory choice for SOC support in ARCH_STM32MP.
This patch is a preliminary step for new SOC introduction
in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move code and defines only needed for CONFIG_STM32MP15x in stm32mp15x.c
when low level init without TFABOOT is supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As the get_otp() helper function in bsec are common for all STM32MP family,
move this function in bsec driver
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SPL is only supported by STM32MP15x not by all the
SOC with STM32MP arch.
Only TFABOOT is supported in next products.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CONFIG_SPL_RAW_IMAGE_SUPPORT default y has been used to replace
CONFIG_SPL_ABORT_ON_RAW_IMAGE for quite some time, so drop
CONFIG_SPL_ABORT_ON_RAW_IMAGE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart3 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn_beacon
Since these boards has CONFIG_DM_SERIAL and/or CONFIG_SPL_DM_SERIAL,
the legacy macro no need to be defined.
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for AM62x SoC identification.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add pinctrl macros for AM62x SoCs. These macro definitions are similar
to that of previous platforms, but adding new definitions to avoid any
naming confusions in the SoC dts files.
checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses
However, we do not need parentheses enclosing the values for this
macro as we do intend it to generate two separate values as has been
done for other similar platforms.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phy used in the 8 bit instance has been changed to the phy used in 4
bit instance on AM62 SoC. This implies the phy configuration required for
both the instances of mmc are similar. Therefore, add a new compatible
for AM62 SoC using the driver data of am64 4 bit instance.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
