Commit graph

3610 commits

Author SHA1 Message Date
David Wu
64a12202ed clk: rockchip: clk_rk3368: Implement "assign-clock-parent"
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:39 +01:00
David Wu
424324d3ca rockchip: pinctrl: rk322x: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:38 +01:00
David Wu
dfb886d4f2 rockchip: pinctrl: Add rk3328 gmac pinctrl support
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:37 +01:00
David Wu
301fff4e57 rockchip: pinctrl: rk3328: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:37 +01:00
David Wu
77c4261130 rockchip: pinctrl: rv1108: Move the iomux definitions into pinctrl-driver
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:36 +01:00
David Wu
0788a31e03 rockchip: grf_rv1108.h: Fix the grf offsets
The last 4 grf registers offset of rv1108 are wrong, fix them
for correct usage.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:36 +01:00
Patrice Chotard
20fe38e75a clk: clk_stm32f: Move SYSCFG clock setup into configure_clocks()
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.

As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.

Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-28 09:39:15 -05:00
Patrice Chotard
68a69ed2a4 clk: clk_stm32f: Remove STMMAC clock setup
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2018-01-28 09:39:15 -05:00
Tom Rini
1d12a7c8cd Merge git://git.denx.de/u-boot-spi 2018-01-26 07:46:34 -05:00
Chris Packham
df16881cea spi: kirkwood_spi: implement workaround for FE-9144572
Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz.  However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.

Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:04:08 +05:30
Rajesh Bhagat
23a12cb3d0 board: common: vid: Add support for LTC3882 voltage regulator chip
Restructures common driver to support LTC3882 voltage regulator
chip.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23 11:19:56 -08:00
Rajesh Bhagat
a1f95ff7d7 armv8: lsch3: Add serdes and DDR voltage setup
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23 11:18:12 -08:00
Lokesh Vutla
10f430f3f1 board: ti: am574x-idk: Add hw data support
Update prcm, voltages and pinmux support for am574x-idk.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
941f2fcc5b arm: dra762: Add support for device package identification
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs

Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
8a8af8a2fd cmd: ti: Generalize cmd_ddr3 command
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7  platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
650fda93c8 arm: emif-common: Add suppport for enabling ECC
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
2018-01-19 15:49:25 -05:00
Lokesh Vutla
e18cd3d796 arm: emif-common: Add ecc specific emif registers
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:25 -05:00
Tero Kristo
72b7af5a04 drivers: dma: ti-edma3: add support for memory fill
Add support for simple memory fill operation. With large data sizes
it is much faster to use EDMA for memory fill rather than CPU.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2018-01-19 15:49:25 -05:00
Vignesh R
e36edcec0a board: ti: dra7xx: Select MCAN instead of DCAN on DRA76 EVM
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-01-19 15:49:23 -05:00
Kishon Vijay Abraham I
29171dcfaa mmc: omap_hsmmc: Fix incorrect bit operations for disabling a bit
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".

Fix it here by using "&= ~()" to reset a bit.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:23 -05:00
Kishon Vijay Abraham I
f0d53e88a6 mmc: omap_hsmmc: Add support for DMA (ADMA2)
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:17 -05:00
Jean-Jacques Hiblot
f844d5f4e6 omap: Update the base address of the MMC controllers
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.

Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Jean-Jacques Hiblot
741726ae4c Revert "omap_hsmmc: update struct hsmmc to accommodate omap3 from DT"
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Tom Rini
8e9801c283 Merge git://git.denx.de/u-boot-imx 2018-01-15 16:44:18 -05:00
Bryan O'Donoghue
aeae70fac5 arm: imx: hab: Define rvt_failsafe()
The hab_rvt_failsafe() callback according to the HABv4 documentation:

"This function provides a safe path when image authentication has failed
and all possible boot paths have been exhausted. It is intended for use by
post-ROM boot stage components, via the ROM Vector Table."

Once invoked the part will drop down to its BootROM USB recovery mode.
Should it be the case that the part is in secure boot mode - only an
appropriately signed binary will be accepted by the ROM and subsequently
executed.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
07eefaf16e arm: imx: hab: Make imx_hab_is_enabled global
It will be helpful to boot commands to know if the HAB is enabled. Export
imx_hab_is_enabled() now to facilitate further work with this data-point in
a secure-boot context.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
57f6548606 arm: imx: hab: Prefix authenticate_image with imx_hab
Tidy up the HAB namespace a bit by prefixing external functions with
imx_hab. All external facing functions past this point will be prefixed in
the same way to make the fact we are doing IMX HAB activities clear from
reading the code. authenticate_image() could mean anything
imx_hab_authenticate_image() is on the other hand very explicit.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
1addedadc4 arm: imx: hab: Define rvt_check_target()
The hab_rvt_check_target() callback according to the HABv4 documentation:

"This function reports whether or not a given target region is allowed for
 either peripheral configuration or image loading in memory. It is intended
 for use by post-ROM boot stage components, via the ROM Vector Table, in
 order to avoid configuring security-sensitive peripherals, or loading
 images over sensitive memory regions or outside recognized memory devices
 in the address map."

It is a useful function to support as a precursor to calling into
authenticate_image() to validate the target memory region is good.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
cd2d46003c arm: imx: hab: Add IVT header definitions
The various i.MX BootROMs containing the High Assurance Boot (HAB) block
rely on a data structure called the Image Vector Table (IVT) to describe to
the BootROM where to locate various data-structures used by HAB during
authentication.

This patch adds a definition of the IVT header for use in later patches,
where we will break the current incorrect dependence on fixed offsets in
favour of an IVT described parsing of incoming binaries.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
c5800b2541 arm: imx: hab: Fix authenticate_image input parameters
u-boot command "hab_auth_img" tells a user that it takes

- addr - image hex address
- offset - hex offset of IVT in the image

but in fact the callback hab_auth_img makes to authenticate_image treats
the second 'offset' parameter as an image length.

Furthermore existing code requires the IVT header to be appended to the end
of the image which is not actually a requirement of HABv4.

This patch fixes this situation by

1: Adding a new parameter to hab_auth_img
   - addr   : image hex address
   - length : total length of the image
   - offset : offset of IVT from addr

2: Updates the existing call into authenticate_image() in
   arch/arm/mach-imx/spl.c:jump_to_image_no_args() to pass
   addr, length and IVT offset respectively.

This allows then hab_auth_img to actually operate the way it was specified
in the help text and should still allow existing code to work.

It has the added advantage that the IVT header doesn't have to be appended
to an image given to HAB - it can be prepended for example.

Note prepending the IVT is what u-boot will do when making an IVT for the
BootROM. It should be possible for u-boot properly authenticate images
made by mkimage via HAB.

This patch is the first step in making that happen subsequent patches will
focus on removing hard-coded offsets to the IVT, which again is not
mandated to live at the end of a .imx image.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
08a81cad2f arm: imx: hab: Move CSF_PAD_SIZE to hab.h
CSF_PAD_SIZE should be defined in hab.h, move it to that location now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
191d8bd509 arm: imx: hab: Move IVT_SIZE to hab.h
The size of the IVT header should be defined in hab.h move it there now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
adbb051f08 arm: imx: hab: Make authenticate_image return int
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.

Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.

The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.

The first step is fixing the return type in authenticate_image() so do that
now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Stephen Warren
8163faf952 ARMv8: add optional Linux kernel image header
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12 09:52:11 -07:00
Tom Rini
1a62f8597c Merge git://git.denx.de/u-boot-video 2018-01-11 13:43:36 -05:00
Tom Rini
6bf634223a Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-11 11:18:49 -05:00
Tom Rini
e38c66edae Merge git://git.denx.de/u-boot-usb 2018-01-11 11:18:29 -05:00
Hannes Schmelzer
3215192922 mach-omap2: add AM335x Display PLL register definition
Adds the register definition of the Display DPLL

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:16:34 +01:00
Sumit Garg
1cabeb88eb ls1088ardb: Add SD Secure boot target support
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[YS: run moveconfig.py -s]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:32:45 -08:00
Ahmed Mansour
44262327aa drivers/misc: Share qbman init between archs
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware

- Create new board/freescale/common/fsl_portals.c to house shared
  device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
  both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
  setup to disable interrupts on all QMan and BMan portals. It is
  needed because the interrupts are enabled by default for all portals
  including unused/uninitialised portals. When the kernel attempts to
  go to deep sleep the unused portals prevent it from doing so

Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:47 -08:00
Yuantian Tang
1b76f3b8ab armv8: layerscape: sata: refine port register configuration
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:14 -08:00
Patrice Chotard
c8f787760e board: stm32f429-disco: switch to DM STM32 pinctrl and gpio driver
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.

Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Patrice Chotard
4a56fd484a board: stm32f429-disco: switch to DM STM32 clock driver
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.

Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.

Enable also CLK flag.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Patrice Chotard
2d18d72858 board: stm32f429-disco: switch to DM STM32 serial driver
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.

The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Eddie Cai
bf2b72bef1 usb: rockchip: add the rockusb gadget
this patch implement rockusb protocol on the device side. this is based on
USB download gadget infrastructure. the rockusb function implements the rd,
wl, rid commands. it can work with rkdeveloptool

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-10 11:11:05 +01:00
Elaine Zhang
538f67c332 rockchip: clk: bind reset driver
Bind rockchip reset to clock-controller with rockchip_reset_bind().

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-09 11:13:32 +01:00
Stefan Agner
46718353b2 imx: initialize and use generic timer on i.MX 6UL/ULL
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.

This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-08 17:33:06 +01:00
Fabio Estevam
290e7cfdbf mx6ull: Handle the CONFIG_MX6ULL cases correctly
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.

This fixes a boot regression.

Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
2018-01-04 16:29:04 +01:00
Eran Matityahu
af104ae5b8 imx: spl: Fix NAND bootmode detection
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.

Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
2018-01-03 14:01:38 +01:00
Fabio Estevam
4555c26142 imx: Add a common way for detecting NXP boards revision
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.

Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-29 11:18:59 +01:00
Tom Rini
eeab579aa8 Merge git://git.denx.de/u-boot-rockchip 2017-12-18 18:39:18 -05:00
Tom Rini
1a3fc354b5 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-12-18 18:39:00 -05:00
Kever Yang
270288544e rockchip: update boot0 hook
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.

The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.

Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-18 16:56:05 +01:00
Michal Simek
2d2af5d834 arm64: zynqmp: Add missing zynq_board_read_rom_ethaddr() prototype
Add missing zynq_board_read_rom_ethaddr() prototype reported by sparse.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2017-12-14 20:08:44 +01:00
Wenbin song
a8f33034f2 armv8: ls1043a/ls2080a: check SoC by device ID
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-13 13:40:29 -08:00
Tuomas Tynkkynen
a72c618068 ARM: pxa: Remove unused ifdefs
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 21:34:10 -05:00
Tuomas Tynkkynen
b82e667f79 ata: Migrate CONFIG_LIBATA to Kconfig
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:16:05 -05:00
Tuomas Tynkkynen
9fd95ef0d3 ata: Migrate CONFIG_SCSI_AHCI to Kconfig
And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:13:19 -05:00
Tom Rini
0c4d24823e Merge git://git.denx.de/u-boot-uniphier 2017-12-04 10:24:35 -05:00
Peng Fan
90351547ce armv8: mmu: fix page table mapping
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-04 10:23:52 -05:00
Neil Armstrong
c7be3e5a79 ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.

But mainline U-Boot and Linux has the old address and size fixed.

These SoCs have a register interface to get the two firmware reserved
memory start and sizes.

This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.

Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].

[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html

Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()

Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception

Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-04 10:17:29 -05:00
Neil Armstrong
6915b10331 ARM: arch-meson: add ethernet common init function
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04 09:59:02 -05:00
Masahiro Yamada
6ae3900a86 mtd: nand: Rename nand.h into rawnand.h
This header was renamed to rawnand.h in Linux.

The following is the corresponding commit in Linux.

  commit d4092d76a4a4e57b65910899948a83cc8646c5a5
  Author: Boris Brezillon <boris.brezillon@free-electrons.com>
  Date:   Fri Aug 4 17:29:10 2017 +0200

      mtd: nand: Rename nand.h into rawnand.h

      We are planning to share more code between different NAND based
      devices (SPI NAND, OneNAND and raw NANDs), but before doing that
      we need to move the existing include/linux/mtd/nand.h file into
      include/linux/mtd/rawnand.h so we can later create a nand.h header
      containing all common structure and function prototypes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-04 22:00:00 +09:00
Philipp Tomsich
4fc495e9e2 rockchip: clk: rk3128: fix DCLK_VOP_DIV_CON_MASK
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.

Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-02 00:27:42 +01:00
Philipp Tomsich
cd401abcd5 rockchip: clk: rk3128: fix NANDC_PLL_SEL_MASK
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.

Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-02 00:27:31 +01:00
Kever Yang
e129c480e4 rockchip: rk3128: add pinctrl driver
Add rk3128 pinctrl driver and grf/iomux structure definition.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:26 +01:00
Kever Yang
9246d9e541 rockchip: rk3128: add clock driver
Add rk3128 clock driver and cru structure definition.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:26 +01:00
Patrice Chotard
014a953c4a stm32: migrate clock structs in include/stm32_rcc.h
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
4e97e25723 clk: clk_stm32fx: add clock configuration for mmc usage
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.

STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.

Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
c88c6a9e03 clk: stm32fx: migrate define from rcc.h to driver
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
d0a768b1c8 clk: stm32f7: retrieve PWR base address from DT
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Tom Rini
b06c46de63 Xilinx changes for v2018.1
Zynq:
 - Add support for Syzygy and cc108 boards
 - Add support for mini u-boot configurations (cse)
 - dts updates
 - config/defconfig updates in connection to Kconfig changes
 - Fix psu_init handling
 
 ZynqMP:
 - SPL fixes
 - Remove slcr.c
 - Fixing r5 startup sequence
 - Add support for external pmufw
 - Add support for new ZynqMP chips
 - dts updates
 - Add support for zcu102 rev1.0 board
 
 Drivers:
 - nand: Support external timing setting and board init
 - ahci: Fix wording
 - axi_emac: Wait for bit, non processor mode, readl/write conversion
 - zynq_gem: Fix SGMII/PCS support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
 MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
 =BqNN
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.1

Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling

ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board

Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
2017-11-29 08:26:07 -05:00
Masahiro Yamada
ed3986ca30 bitops: collect BIT macros to include/linux/bitops.h
Same macros are defined in various places.  Collect them into
include/linux/bitops.h like Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Michal Simek
494fffe70d arm64: zynqmp: Add support for CG/EG/EV device detection
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.

These efuse bits are setup for certain devices.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Siva Durga Prasad Paladugu
e042d36e17 arm64: zynqmp: Provide a Kconfig option to use specified memory for MMU table
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Michal Simek
62e950fad3 arm64: zynqmp: Remove slcr with mio status pin detection
This code is not used on this platform and it is not called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:55 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Fabio Estevam
e2162d709f imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.

It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.

While at it, rename it to imx_wdog_disable_powerdown().

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-27 10:34:49 +01:00
Fabio Estevam
23ecca2cd8 mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:31 +01:00
Philipp Tomsich
8c2bb589e2 rockchip: pinctrl: rk3399: add support for I2C8
The RK3399 has a total of 9 I2C controllers.  To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.

For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-26 00:39:08 +01:00
Andy Yan
b4d23f7643 rockchip: add support for enter to bootrom download mode
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Andy Yan
e3067793c3 rockchip: make boot_mode related codes reused across all platforms
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Kever Yang
6ba54058ed rockchip: sysreset: merge into one common driver
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
b82bd1f8d4 rockchip: back-to-bootrom: allow passing a cmd to the bootrom
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it.  There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.

All the existing call-sites are adjusted to match the changed function
signature.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ecfd71891a rockchip: back-to-bootrom: replace assembly-implementation with C-code
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.

This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b4806d6f1f arm: provide a PCS-compliant setjmp implementation
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers.  One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.

To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
7776cc011d arm: make save_boot_params_ret prototype visible for AArch64
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).

This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b377d22264 rockchip: boot0 hook: support early return for RK3188/RK3066-style BROM
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.

To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
16d761e3dd bcm281xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
62269f02ab bcm235xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 5
- ran 'whitespace-cleanup'
2017-11-21 23:57:21 +01:00
Kever Yang
cee7470cd8 rockchip: boot0: align to 0x20 for armv7 '_start'
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
ef70a42f0f arm: boot0 hook: move boot0 hook before '_start'
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.

To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
  (1) if a boot0-hook is present it is inserted at the start of
      the image
  (2) if a boot0-hook is present, emitting the ARM vector table
      (and the _start) symbol are suppressed in vectors.S and
      the boot0-hook has full control over where and when it
      wants to emit these

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Beniamino Galvani
456efb5127 odroid-c2: enable I2C
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-20 10:11:44 +01:00
Beniamino Galvani
f8d9ca1833 i2c: add Amlogic Meson driver
Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-20 10:11:34 +01:00
Martyn Welch
54d8d4942f arm: mx5: Add more register definitions
Add register definitions require for video configuration.

Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Martyn Welch
065a1ece7a pwm: imx: Enable PWM support on i.MX53
Add missing parts for i.MX53 PWM support

Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Landheer-Cieslak, Ronald
48c7f77128 Add UART base addresses for additional UARTs
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.

Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17 10:53:45 -05:00
Stephen Warren
49e93875a6 arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17 07:44:13 -05:00
Neil Armstrong
ea990816fe arm: meson: Add supplementary ethernet registers definitions
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17 07:44:13 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Lukasz Majewski
9c8979cdb7 imx7: Add include guards for include/asm/arch-mx7/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
e895e996ab imx5: Add include guards for include/asm/arch-mx5/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
90d0e38c1e imx6: Add include guards for include/asm/arch-mx6/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
ec1b26973c imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCs
This commit provides generic function to set the RGMII/HSIC IO voltage
level on iMX6 devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Patrice Chotard
e36591c350 spear: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for SPEAR
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
1537d38619 stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
fb48bc448c sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Fabio Estevam
e1f0715f64 wandboard: Add support for the MX6QP variant
Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-31 11:01:38 +01:00
Tom Rini
2d5e6b4aac Merge git://git.denx.de/u-boot-video 2017-10-29 10:11:08 -04:00
Tom Rini
bb3d9ed3a9 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-27 21:59:10 -04:00
Sumit Garg
9b3f40ad09 armv8: sec_firmware: Add support for loadables in FIT
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.

Brief description of implementation:
  Add two more address pointers (loadable_h, loadable_l) as arguments to
  sec_firmware_init() api.
  Create new api: sec_firmware_checks_copy_loadable() to check if loadables
  node is present in SEC firmware FIT image. If present, verify loadable
  image and copies it to secure DDR memory.
  Populate address pointers with secure DDR memory addresses where loadable
  is copied.

Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Sumit Garg
9781d9ff5f armv8: layerscape: Allocate 66 MB DDR for secure memory
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Vasily Khoruzhick
79f285ddeb sunxi: video: split out PLL configuration code
It will be reused in new DM LCD driver.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2017-10-27 09:39:19 +02:00
Quentin Schulz
c96f598be7 sunxi: clk: fix N formula for CPUX clocks
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).

This results in a clock set to a frequency that isn't specified as
possible for CPUs.

Let's use the correct formula.

Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-25 10:05:05 +02:00
Tom Rini
26f9184e09 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-12 13:36:58 -04:00
Diego Dorta
e2000731ae mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functions
When compiling with W=1 errors are observed:

drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)

drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)

Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:18 +02:00
Diego Dorta
342b4b09b1 mx6: clock: Add a prototype for do_mx6_showclocks()
When compiling with W=1 the following warning is observed:

arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])

Remove this warning by adding the function prototype into arch-mx6/clock.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:01 +02:00
Uri Mashiach
c5c6f37a04 imx: mx7: SPL support for i.MX7
Add configuration file and spl_boot_device function for the i.MX7 SPL.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
258bad41ac imx: mx7: DDR controller configuration for the i.MX7 architecture
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
8bf2d77806 imx: mx7: fix the CCM_ macros
The CCM_ macros use the CCM_BASE_ADDRESS macro, which doesn't exist.
Replace the CCM_BASE_ADDRESS macros with CCM_BASE_ADDR.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2017-10-12 17:31:16 +02:00
Diego Dorta
9f272573b7 imx: sys_proto: Add a prototype for board_mmc_get_env_dev()
When compiling with W=1 the following warning is observed:

board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)

Remove this warning by adding the function prototype into sys_proto.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-10-12 17:31:16 +02:00
York Sun
fb97b8621e armv8: layerscape: Enable falcon boot
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
2017-10-09 08:48:45 -07:00
zijun_hu
34f9a92583 ARMv8: make master CPU checking logic more clear
macro branch_if_master checks master CPU via (Aff3 & (Aff2:Aff1:Aff0))
it is simple but a little obscure.

fix by checking Affx fields within MPIDR_EL1 directly.

Signed-off-by: zijun_hu <zijun_hu@htc.com>
2017-10-08 16:19:56 -04:00
Maxime Ripard
8829076a5b arm: sunxi: Move spl_boot_device in a separate function
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.

Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.

Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
3a61b080ac musb: sunxi: switch to the device model
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.

Switch to probing both in peripheral and host mode through the DT.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Paul Burton
8f8e6304df arm: Use asm-generic/io.h
Convert the arm architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arm this is primarily a matter of removing code.

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-02 21:52:20 -04:00
Philipp Tomsich
3b4f87735d rockchip: bootrom: add definitions to retrieve BROM boot-source
The Rockchip BROM allows reading where it booted from from SRAM.
This adds the necessary definitions (as received from Kever) for
the location of this information in the RK3399's SRAM and naming
for the constants used.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Jagan Teki
a982d5156d armv7: rk3288: Move configure_l2ctlr to common
configure_l2ctlr will be shared between SPL and TPL so
move them into asm/arch/sys_proto.h

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Jagan Teki
d9a7dcf5b8 armv7: Move L2CTLR read/write to common
L2CTLR read/write functions are common to armv7 so, move
them in to include/asm/armv7.h and use them where ever it need.

Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Backed out the change to arch/arm/mach-tegra/cache.c:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Kever Yang
04e97e48d0 rockchip: rk3036: fix grf macro define
Some of macros definition are not correct, fix them according to TRM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Kever Yang
0176399b79 rockchip: rk322x: add sdram driver
Add driver for rk322x to support sdram initialize in SPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
David Wu
615514c16d rockchip: clk: Add rk3368 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
2e4ce50d1a rockchip: clk: Add rv1108 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:29 +02:00
Sriram Dash
e45ff0ce63 armv8: fsl: ifc: Put IFC related code under CONFIG_FSL_IFC
IFC code is put under CONFIG_FSL_IFC

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:45:17 -07:00
Patrice Chotard
246771b184 board: Add stm32h7 SoC, discovery and evaluation boards support
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.

For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:03 -04:00
Patrice Chotard
40d1a31e63 usb: dwc3: Add dwc3 glue driver support for STi
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.

Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:59 -04:00
Tom Rini
e884656c2c Merge git://www.denx.de/git/u-boot-imx 2017-09-20 12:32:34 -04:00
David Wu
4c94aacd62 rockchip: rk322x: Disable integrated macphy for saving power consuming
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:33 +02:00
Eric Nelson
8590786acf imx: imx7d: remove CamelCase from ENET_xMHz macros
Update these macros to use all upper-case to avoid checkpatch
warnings:

	ENET_25MHz,
	ENET_50MHz,
	ENET_125MHz,

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-18 17:15:28 +02:00
Stefan Agner
7d289d6239 imx: add macro to detect whether USB PHY is active
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.

The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18 16:51:36 +02:00
Suman Anna
2f9455c849 ARM: DRA7: Cleanup old pinctrl macros
Commit 6ae4c3efbd ("ARM: DRA7: Add pinctrl register definitions")
has added new macros for pinmux configuration in line with the kernel
definitions. Cleanup the old pinctrl macros from the common header
file so that they are not used by any new boards.

Signed-off-by: Suman Anna <s-anna@ti.com>
2017-09-14 21:32:56 -04:00
Vishal Mahaveer
ba39608147 ARM: DRA72x: Add support for detection of DRA71x SR 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-12 18:02:29 -04:00
Masahiro Yamada
b27af39935 dma: import linux/dma-direction.h to consolidate enum dma_data_direction
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-09-12 18:02:23 -04:00
Andy Yan
347e30e172 armv8: mmu: add space around operator
Add space around operator "+", make it
match the coding style.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12 18:00:09 -04:00
Andy Yan
4f84cb980f armv8: mmu: remove unused macro definition
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12 18:00:08 -04:00
Tom Rini
8a33cb8b6b Merge git://git.denx.de/u-boot-fsl-qoriq 2017-09-12 12:02:50 -04:00
Steve Kipisz
209742fa88 board: ti: am571x: Add 666MHz support for AM571x IDK
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11 16:22:31 -04:00
Keerthy
c247605510 board: ti: dra76-evm: Add the pmic data
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:40 -04:00
Praneeth Bajjuri
0f9e6aee9d arm: dra76: Add support for ES1.0 detection
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN

Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:38 -04:00