Commit graph

347 commits

Author SHA1 Message Date
Bin Meng
d0b3e3bfbb x86: quark: Add clrbits, setbits, clrsetbits macros for message port access
On Intel Quark, lots of registers on the message port need be
programmed. Add handy clrbits, setbits, clrsetbits macros for
message port access.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-16 19:53:52 -06:00
Bin Meng
2afb62305e x86: quark: Add PCIe/USB static register programming after memory init
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-16 19:53:52 -06:00
Bin Meng
b06862b9d8 x86: quark: Add USB PHY initialization support
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
316fd3920f x86: Enable PCIe controller on quark/galileo
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.

Enable PCIe controller per Quark firmware writer guide.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
5750e5e29a x86: quark: Optimize MRC execution time
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.

To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Saket Sinha
867bcb63e7 x86: Generate a valid ACPI table
Implement write_acpi_table() to create a minimal working ACPI table.
This includes writing FACS, XSDT, RSDP, FADT, MCFG, MADT, DSDT & SSDT
ACPI table entries.

Use a Kconfig option GENERATE_ACPI_TABLE to tell U-Boot whether we need
actually write the APCI table just like we did for PIRQ routing, MP table
and SFI tables. With ACPI table existence, linux kernel gets control of
power management, thermal management, configuration management and
monitoring in hardware.

Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tidied up whitespace and aligned some tabs:
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:13 -07:00
Bin Meng
c78dfb4fd2 x86: superio: Add keyboard controller support to smsc_lpc47m driver
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:12 -07:00
Bin Meng
c17ca6b5cd x86: Remove calculate_relocation_address()
Now that we have generic routine to calculate relocation address,
remove the x86 specific one which is now only used by coreboot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:07 -07:00
Bin Meng
89b870814c x86: coreboot: Increase memrange entry number to 32
Increase lib_sysinfo memrange entry number to 32 to sync with coreboot.
This allows a complete E820 table to be reported to the kernel, as on
some platforms (eg: Bayley Bay) having only 16 entires does not cover
all the memory ranges.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:06 -07:00
Simon Glass
ecf674b772 x86: Drop FSP error defines and use EFI instead
Now that we have an efi.h header we can use that for FSP error defines.
Drop the FSP ones.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:13 -06:00
Simon Glass
2db9374561 x86: Move the GDT into global_data
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:10 -06:00
Simon Glass
93afae5d05 x86: Remove init_gd() function
This is declared but no-longer exists. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
7e4be120e8 x86: Allow pirq_init() to return an error
This function can fail. In this case we should return the error rather than
swallowing it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
412400abaa x86: Split out fsp_init_phase_pci() code into a new function
This code may be useful for boards that use driver model for PCI.

Note: It would be better to have driver model automatically call this
function somehow. However for now it is probably safer to have it under
board control.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Bin Meng
da60fb7934 x86: fsp: Do not assert VPD_IMAGE_REV when DEBUG
When using different release version of Intel FSP, the VPD_IMAGE_REV
is different (ie: BayTrail Gold 3 is 0x0303 while Gold 4 is 0x0304).
Remove the asserting of this so that U-Boot does not hang in a debug
build.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-14 03:24:21 -06:00
Simon Glass
42fde30500 x86: Add support for passing tables into U-Boot
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.

Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00
Simon Glass
96a8d409a7 efi: Add 64-bit payload support
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.

Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00
Simon Glass
6f92ed8f1a x86: Add a way to call 32-bit code from 64-bit mode
The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00
Simon Glass
7dfe8bdeef x86: Add an enum for some commonly-used GDT bits
Rather than add these as open-coded values, create an enum with the commonly
used flags.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00
Ben Stoltz
3dcdd17b43 x86: Add support for U-Boot as an EFI application
Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.

Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:06 -06:00
Simon Glass
ed3b4d3736 x86: Add asm/elf.h for x86-specific ELF definitions
Bring in this file from Linux 4.1. It supports relocation features specific
to x86.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:05 -06:00
Simon Glass
867a6ac86d efi: Add start-up library code
When running as an EFI application, U-Boot must request memory from EFI,
and provide access to the boot services U-Boot needs.

Add library code to perform these tasks. This includes efi_main() which is
the entry point from EFI. U-Boot is built as a shared library.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:42:41 -06:00
Simon Glass
8f3b9694b2 x86: Allow use of global_data with EFI
On x86 the global_data pointer is provided through a somewhat-bizarre and
x86-specific mechanism: the F segment register is set to a pointer to the
start of global_data, so that accesses can use this build-in register.

When running as an EFI application we don't want to mess with the Global
Descriptor Table (GDT) and there is little advantage (in terms of code size)
to doing so.

Allow global_data to be a simple variable in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:42:41 -06:00
Simon Glass
0d9edd2dfb x86: Drop unused copy_fdt_to_ram()
This is now handled by generic U-Boot code so we do not need an x86 version.
It is no-longer called, so remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:42:40 -06:00
Simon Glass
83ec7de3bc x86: Tidy up global_data flags
These flags now overlap some global ones. Adjust the x86-specific flags to
avoid this. Since this requires a change to the start.S code, add a way for
tools to find the 32-bit cold reset entry point. Previously this was at a
fixed offset.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:42:40 -06:00
Bin Meng
3e79a4ab26 x86: baytrail: Update UPD setting for FSP Gold4 release
BayTrail FSP Gold4 release adds one UPD parameter to control IGD
enable/disable.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-05 08:42:39 -06:00
Bin Meng
9830d2ebb4 x86: qemu: Turn on PCIe ECAM address range decoding on Q35
Turn on PCIe ECAM address range decoding on Q35.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:25 -06:00
Bin Meng
e7cd070da6 x86: qemu: Enable I/O APIC chip select on PIIX3
The PIIX3 chipset does not integrate an I/O APIC, instead it supports
connecting to an external I/O APIC which needs to be enabled manually.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:24 -06:00
Bin Meng
abab912813 x86: mpspec: Allow platform to determine how PIRQ is connected to I/O APIC
Currently during writing MP table I/O interrupt assignment entry, we
assume the PIRQ is directly mapped to I/O APIC INTPIN#16-23, which
however is not always the case on some platforms.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:24 -06:00
Bin Meng
31a2dc6955 x86: pci: Assign pci irqs to all functions
We need walk through all functions within a PCI device and assign
their IRQs accordingly.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:22 -06:00
Bin Meng
8ba25eec86 x86: Change pci option rom area MTRR setting to cacheable
Turn on cache on the pci option rom area to improve the performance.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:22 -06:00
Bin Meng
013cf483c9 x86: Display correct CS/EIP/EFLAGS when there is an error code
Some exceptions cause an error code to be saved on the current stack
after the EIP value. We should extract CS/EIP/EFLAGS from different
position on the stack based on the exception number.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:21 -06:00
Masahiro Yamada
5f7e310467 x86: delete unneeded declarations of disable_irq() and enable_irq()
These two declarations in arch/x86/include/asm/interrupt.h conflict
with ones in include/linux/compat.h, so x86 boards cannot include
<linux/compat.h>.

The comment /* arch/x86/lib/interrupts.c */ is bogus now, and we do
not see any definitions of disable_irq() and enable_irq() in there.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-22 07:30:31 -06:00
Bin Meng
a452002259 x86: Configure VESA parameters before loading Linux kernel
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
2015-07-14 18:03:19 -06:00
Bin Meng
43dd22f5fc x86: Setup fixed range MTRRs for legacy regions
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:18 -06:00
Bin Meng
07545d861c x86: Generate a valid MultiProcessor (MP) table
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.

Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:17 -06:00
Bin Meng
7f5df8d42d x86: Add MultiProcessor (MP) table APIs
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:17 -06:00
Bin Meng
a2d73fdba6 x86: Remove inline for lapic access routines
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:17 -06:00
Bin Meng
3d23287828 x86: Add I/O APIC register access routines
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:17 -06:00
Bin Meng
ba9091f55d x86: Clean up ioapic header file
Remove all the dead/unused macros from asm/ioapic.h.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:17 -06:00
Bin Meng
63d54a6705 x86: Clean up lapic codes
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
  defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
  CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
  it is not apic related and only used by ivybridge
- Fix coding convention issues

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:16 -06:00
Bin Meng
6e6f4ce4f8 x86: Move MP initialization codes into a common place
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:16 -06:00
Bin Meng
be3f06bcc4 x86: dm: Clean up cpu drivers
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
  file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
  naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
  the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
  cpu_x86_bind()

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:15 -06:00
Bin Meng
aefaff8ed8 x86: fsp: Move FspInitEntry call to board_init_f()
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.

Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:15 -06:00
Bin Meng
002610f620 x86: fsp: Load GDT before calling FspInitEntry
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.

To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-14 18:03:15 -06:00
Gabriel Huau
5318f18d2c x86: gpio: add pinctrl support from the device tree
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.

Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 03:32:08 -06:00
Bin Meng
65cdd9be3e x86: coreboot: Fix cosmetic issues
Clean up arch/x86/cpu/coreboot.c to fix several cosmetic issues.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 03:03:17 -06:00
Bin Meng
4be2f42bbc x86: qemu: Adjust VGA initialization
As VGA option rom needs to run at C segment, although QEMU PAM emulation
seems to only guard E/F segments, for correctness, move VGA initialization
after PAM decode C/D/E/F segments.

Also since we already tested QEMU targets to differentiate I440FX and Q35
platforms, change to locate the VGA device via hardcoded b.d.f instead of
dynamic search for its vendor id & device id pair.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 02:39:40 -06:00
Bin Meng
0fcb7acf67 x86: qemu: Enable legacy IDE I/O ports decode
QEMU always decode legacy IDE I/O ports on PIIX chipset. However Linux ata_piix
driver does sanity check to see whether legacy ports decode is turned on.
To make Linux ata_piix driver happy, turn on the decode via IDE_TIMING register.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 02:39:39 -06:00
Bin Meng
cc7debc719 x86: qemu: Turn on legacy segments decode
By default the legacy segments C/D/E/F do not decode to system RAM.
Turn on the decode via Programmable Attribute Map (PAM) registers
so that we can write configuration tables in the F segment.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 02:39:39 -06:00
Bin Meng
05b98ec346 x86: quark: Implement PIRQ routing
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 02:39:39 -06:00
Bin Meng
9c7dea602e x86: Refactor PIRQ routing support
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-06-04 02:39:39 -06:00
Bin Meng
a65b25d148 x86: Support QEMU x86 targets
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
   https://patchwork.ozlabs.org/patch/479745/
2015-06-04 02:39:38 -06:00
Simon Glass
ede9709316 x86: Add a CPU driver for baytrail
This driver supports multi-core init and sets up the CPU frequencies
correctly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-30 16:13:50 -06:00
Simon Glass
bcb0c61e1a x86: Allow CPUs to be set up after relocation
This permits init of additional CPU cores after relocation and when driver
model is ready.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-30 16:13:48 -06:00
Simon Glass
86196c65ac x86: Add functions to set and clear bits on MSRs
Since we do these sorts of operations a lot, it is useful to have a simpler
API, similar to clrsetbits_le32().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-30 16:13:46 -06:00
Simon Glass
45b5a37836 x86: Add multi-processor init
Most modern x86 CPUs include more than one CPU core. The OS normally requires
that these 'Application Processors' (APs) be brought up by the boot loader.
Add the required support to U-Boot to init additional APs.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-30 16:13:38 -06:00
Simon Glass
6f41e0e7bc x86: Provide access to the IDT
Add a function to return the address of the Interrupt Descriptor Table.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:34 -06:00
Simon Glass
52845296be x86: Store the GDT pointer in global_data
When we start up additional CPUs we want them to use the same Global
Descriptor Table. Store the address of this in global_data so we can
reference it later.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:34 -06:00
Simon Glass
837a136fc7 x86: Add an mfence macro
Provide access to this x86 instruction from C code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:34 -06:00
Simon Glass
1a06d2a310 x86: Add defines for fixed MTRRs
Add MSR numbers for the fixed MTRRs.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:34 -06:00
Simon Glass
b551173b73 x86: Add atomic operations
Add a subset of this header file from Linux 4.0 to support atomic operations
in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:33 -06:00
Simon Glass
6388e35725 x86: Add support for the Simple Firmware Interface (SFI)
This provides a way of passing information to Linux without requiring the
full ACPI horror. Provide a rudimentary implementation sufficient to be
recognised and parsed by Linux.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:33 -06:00
Simon Glass
ff6a8f3c06 x86: Implement reset_cpu() correctly for modern CPUs
The existing code is pretty ancient and is unreliable on modern hardware.
Generally it will hang.

We can use port 0xcf9 to initiate reset on more modern hardware (say in the
last 10 years). Update the reset_cpu() function to do this, and add a new
'full reset' function to perform a full power cycle.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-29 21:02:31 -06:00
Bin Meng
f82a7840f1 x86: quark: Turn on legacy segments decode
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:50 -06:00
Gabriel Huau
4a34e4b86f x86: baytrail: fix the GPIOBASE address
The correct GPIOBASE address on the baytrail is 0x48

Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
afbf1404c1 x86: queensbay: Implement PIRQ routing
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
b5b6b01960 x86: Support platform PIRQ routing
On x86 boards, platform chipset receives up to four different
interrupt signals from PCI devices (INTA/B/C/D), which in turn
will be routed to chipset internal PIRQ lines then routed to
8259 PIC finally if configuring the whole system to work under
the so-called PIC mode (in contrast to symmetric IO mode which
uses IOAPIC).

We add two major APIs to aid this, one for routing PIRQ and the
other one for generating a PIRQ routing table.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
5e2400e8f8 x86: Write configuration tables in last_stage_init()
We can write the configuration table in last_stage_init() for all x86
boards, but not with coreboot since coreboot already has them.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
e3e7fa2cd1 x86: Add a function to assign IRQ numbers to PCI device
Add a function to assign an IRQ number to PCI device's interrupt
line register in its configuration space, so that the PCI device
can have its interrupt working under PIC mode after OS boots up.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
24ff8e70e1 x86: Clean up arch/x86/include/asm/e820.h
There are lots of unused codes defined in e820.h, clean it up.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:49 -06:00
Bin Meng
19268834fb x86: Set serial port IRQ for SMSC LPC47M
For starting a Linux console on the superio serial port under
interrupt mode, the IRQ number must be configured.

Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:48 -06:00
Bin Meng
9704f23b00 x86: queensbay: Avoid using PCH prefix
The prefix PCH was taken from ivybridge port. However Queensbay
platform official document does not mention PCH. It is composed
of TunnelCreek processor and Topcliff IOH chipset. For accuracy,
avoid using PCH prefix in the macro.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:48 -06:00
Simon Glass
ba4575626e dm: x86: spi: Convert ICH SPI driver to driver model
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.

Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:14 -06:00
Simon Glass
aad78d2732 dm: x86: pci: Convert chromebook_link to use driver model for pci
Move chromebook_link over to driver model for PCI.

This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)

This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:09 -06:00
Simon Glass
a219daeafe dm: x86: pci: Add a PCI driver for driver model
Add a simple x86 PCI driver which uses standard functions provided by the
architecture.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:09 -06:00
Simon Glass
31f57c2873 x86: Add a x86_ prefix to the x86-specific PCI functions
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.

In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-16 19:27:41 -06:00
Masahiro Yamada
0a9e7ee5bd generic-board: select SYS_GENERIC_BOARD for some architectures
We have done with the generic board conversion for all the boards
of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86.

Let's select SYS_GENERIC_BOARD for those architectures, so we can
tell which architecture has finished the conversion at a glance.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-03-28 09:03:08 -04:00
Tom Rini
db7a7dee68 Merge branch 'master' of git://git.denx.de/u-boot-x86 2015-02-10 10:42:56 -05:00
Michal Simek
0267ba5d86 common: Move dram_init() declaration to common location
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-09 15:08:48 +01:00
Bin Meng
b162257d4f x86: quark: Initialize non-standard BARs
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:44 -07:00
Bin Meng
0a391b1c79 x86: quark: Add Memory Reference Code (MRC) main routines
Add the main routines for Quark Memory Reference Code (MRC).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:42 -07:00
Bin Meng
828d9af5ec x86: Add basic Intel Quark processor support
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:41 -07:00
Bin Meng
3c8ae536ec x86: Define macros for pci configuration space access
Move PCI_REG_ADDR and PCI_REG_DATA from arch/x86/lib/pci_type1.c to
arch/x86/include/asm/pci.h, also define PCI_CFG_EN so that these
macros can be used for pci configuration space access.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:40 -07:00
Bin Meng
faa8323299 x86: quark: Add routines to access message bus registers
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:40 -07:00
Bin Meng
b994efbd2d x86: Add header files for Intel Quark SoC defines
device.h for integrated pci devices' bdf on Quark SoC and quark.h for
various memory-mapped and i/o-mapped base addresses within SoC.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-02-06 12:07:40 -07:00
Simon Glass
3a1a18ff18 x86: Add support for Intel Minnowboard Max
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.

This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).

Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-06 12:07:39 -07:00
Simon Glass
447f8b018e x86: Allow a UART to be set up before the FSP is ready
Since the FSP is a black box it helps to have some sort of debugging
available to check its inputs. If the debug UART is in use, set it up
after CAR is available.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-06 12:07:38 -07:00
Simon Glass
82196cf34f x86: Adjust the FSP types slightly
To avoid casts, find_fsp_header() should return a pointer. Add asmlinkage
to two API functions which use that convention. UPD_TERMINATOR is common
so move it into a common file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-05 22:16:43 -07:00
Simon Glass
1021af4ded x86: Move common FSP code into a common location
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-05 22:16:43 -07:00
Simon Glass
2d934e5703 x86: Rename MMCONF_BASE_ADDRESS and make it common across x86
This setting will be used by more than just ivybridge so make it common.

Also rename it to PCIE_ECAM_BASE which is a more descriptive name.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-05 22:16:43 -07:00
Simon Glass
191c008a21 x86: Implement a cache for Memory Reference Code parameters
The memory reference code takes a very long time to 'train' its SDRAM
interface, around half a second. To avoid this delay on every boot we can
store the parameters from the last training sessions to speed up the next.

Add an implementation of this, storing the training data in CMOS RAM and
SPI flash.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:45 -07:00
Simon Glass
b18c68d891 x86: Use ipchecksum from net/
The existing IP checksum function is only accessible to the 'coreboot' cpu.
Drop it in favour of the new code in the network subsystem.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:44 -07:00
Bin Meng
3b621ccabd x86: Test mtrr support flag before accessing mtrr msr
On some x86 processors (like Intel Quark) the MTRR registers are not
supported. This is reflected by the CPUID (EAX 01H) result EDX[12].
Accessing the MTRR registers on such processors will cause #GP so we
must test the support flag before accessing MTRR MSRs.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-23 17:24:55 -07:00
Bin Meng
4949166906 x86: Save mtrr support flag in global data
CPUID (EAX 01H) returns MTRR support flag in EDX bit 12. Probe this
flag in x86_cpu_init_f() and save it in global data.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-23 17:24:55 -07:00
Simon Glass
bdc88d4eb3 x86: Support ROMs on other archs
We shouldn't assume that the VGA ROM can always be loaded at c0000. This
is only true on x86 machines.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-01-23 17:24:15 -07:00
Bin Meng
b2439aecd3 x86: fsp: Drop get_hob_type() and get_hob_length()
These two are not worth having separate inline functions as they are
really simple, so drop them.

Also changed 'type' parameter of fsp_get_next_hob() from u16 to uint.

Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:02 -08:00
Simon Glass
c72f74e278 x86: ivybridge: Update microcode early in boot
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.

For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:02 -08:00
Simon Glass
aff2523f69 x86: Add support for MTRRs
Memory Type Range Registers are used to tell the CPU whether memory is
cacheable and if so the cache write mode to use.

Clean up the existing header file to follow style, and remove the unneeded
code.

These can speed up booting so should be supported. Add these to global_data
so they can be requested while booting. We will apply the changes during
relocation (in a later commit).

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:00 -08:00
Simon Glass
6c911c4322 x86: Drop RAMTOP Kconfig
We don't need this in U-Boot since we calculate it based on available memory.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-01-13 07:24:58 -08:00
Bin Meng
949dbc12db x86: Simplify the fsp hob access functions
Remove the troublesome union hob_pointers so that some annoying casts
are no longer needed in those hob access routines. This also improves
the readability.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-12 17:03:41 -08:00
Bin Meng
8f9052fd98 pci: Make pci apis usable before relocation
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.

Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-12 17:03:41 -08:00
Bin Meng
255fd5caa5 x86: Clean up the FSP support codes
This is the follow-on patch to clean up the FSP support codes:

- Remove the _t suffix on the structures defines
- Use __packed for structure defines
- Use U-Boot's assert()
- Use standard bool true/false
- Remove read_unaligned64()
- Use memcmp() in the compare_guid()
- Remove the cast in the memset() call
- Replace some magic numbers with macros
- Use panic() when no valid FSP image header is found
- Change some FSP utility routines to use an fsp_ prefix
- Add comment blocks for asm_continuation and fsp_init_done
- Remove some casts in find_fsp_header()
- Change HOB access macros to static inline routines
- Add comments to mention find_fsp_header() may be called in a
  stackless environment
- Add comments to mention init(&params) in fsp_init() cannot
  be removed

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-18 17:26:08 -07:00
Bin Meng
adfe3b247a x86: crownbay: Add SPI flash support
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-18 17:26:07 -07:00
Bin Meng
b71eec3129 x86: ich6-gpio: Add Intel Tunnel Creek GPIO support
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.

Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-18 17:26:06 -07:00
Bin Meng
b2e02d2865 x86: Add basic support to queensbay platform and crownbay board
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.

Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-18 17:26:06 -07:00
Masahiro Yamada
e6126a5872 x86: move arch-specific asmlinkage to <asm/linkage.h>
Commit 65dd74a674 (x86: ivybridge: Implement SDRAM init) introduced
x86-specific asmlinkage into arch/x86/include/asm/config.h.

Commit ed0a2fbf14 (x86: Add a definition of asmlinkage) added the
same macro define again, this time, into include/common.h.
(Please do not add arch-specific stuff to include/common.h any more;
it is already too cluttered.)

The generic asmlinkage is defined in <linux/linkage.h>.  If you want
to override it with an arch-specific one, the best way is to add it
to <asm/linkage.h> like Linux Kernel.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-12-15 07:22:53 -07:00
Bin Meng
bceb9f0fc8 x86: Support Intel FSP initialization path in start.S
Per Intel FSP architecture specification, FSP provides 3 routines
for bootloader to call. The first one is the TempRamInit (aka
Cache-As-Ram initialization) and the second one is the FspInit
which does the memory bring up (like MRC for other x86 targets)
and chipset initialization. Those two routines have to be called
before U-Boot jumping to board_init_f in start.S.

The FspInit() will return several memory blocks called Hand Off
Blocks (HOBs) whose format is described in Platform Initialization
(PI) specification (part of the UEFI specication) to the bootloader.
Save this HOB address to the U-Boot global data for later use.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-13 22:32:05 -07:00
Bin Meng
95a5a47466 x86: Add post failure codes for bist and car
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-13 22:32:05 -07:00
Bin Meng
8e04d4c537 x86: queensbay: Adapt FSP support codes
Use inline assembly codes to call FspNotify() to make sure parameters
are passed on the stack as required by the FSP calling convention.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2014-12-13 22:32:05 -07:00
Bin Meng
752a0b085b x86: Initial import from Intel FSP release for Queensbay platform
This is the initial import from Intel FSP release for Queensbay
platform (Tunnel Creek processor and Topcliff Platform Controller
Hub), which can be downloaded from Intel website.

For more details, check http://www.intel.com/fsp.

Note: U-Boot coding convention was applied to these codes, so it
looks completely different from the original Intel release.
Also update FSP support codes license header to use SPDX ID.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2014-12-13 22:32:05 -07:00
Bin Meng
a2927e09bc x86: Add a simple superio driver for SMSC LPC47M
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-13 22:32:05 -07:00
Bin Meng
2795573a8c x86: ich6-gpio: Move setup_pch_gpios() to board support codes
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-13 22:32:04 -07:00
Masahiro Yamada
afc366f01b Replace <compiler.h> with <linux/compiler.h>
Including <linux/compiler.h> is enough for general use.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-12-08 09:35:46 -05:00
Simon Glass
effcf067df x86: Add initial video device init for Intel GMA
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 07:11:16 -07:00
Simon Glass
e34aef1de3 x86: Add GDT descriptors for option ROMs
Option ROMs require a few additional descriptors. Add these, and remove the
enum since we now have to access several descriptors from assembler.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:14 -07:00
Simon Glass
24774278c9 x86: ivybridge: Add northbridge init functions
Add init for the northbridge, another part of the platform controller hub.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:14 -07:00
Simon Glass
d1ef1132bb x86: Drop some msr functions that we don't support
These are not available in U-Boot as yet, so drop them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:14 -07:00
Simon Glass
bb80be3916 x86: Add init for model 206AX CPU
Add the setup code for the CPU so that it can be used at full speed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:14 -07:00
Simon Glass
0c9075e9ad x86: Add LAPIC setup code
Add code to set up the Local Advanced Peripheral Interrupt Controller.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-25 06:34:11 -07:00
Bin Meng
1dae2e0eb6 x86: Refactor interrupt_init()
Rename interrupt_init() in arch/x86/lib/pcat_interrupts.c to
i8259_init() and create a new interrupt_init() in
arch/x86/cpu/interrupt.c to call i8259_init() followed by a
call to cpu_init_interrupts().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:02 -07:00
Bin Meng
a549f7497b x86: Remove cpu_init_r() for x86
Since cpu_init_interrupts() was moved out of cpu_init_r(), it is
useless to keep cpu_init_r() for x86, thus remove it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:02 -07:00
Simon Glass
18739e2ccc x86: Add Intel speedstep and turbo mode code
Intel chips have a turbo mode where they can run faster for a short period
until they reach thermal limits. Add code to adjust and query this feature.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:02 -07:00
Simon Glass
a6d4c45306 x86: ivybridge: Set up XHCI USB
Add init for XHCI so that high-speed USB can be used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:02 -07:00
Simon Glass
9baeca4b89 x86: ivybridge: Set up EHCI USB
Add init for EHCI so that USB can be used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:01 -07:00
Simon Glass
3ac839352d x86: ivybridge: Add SATA init
Add code to set up the SATA interfaces on boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:01 -07:00
Simon Glass
8c74a57318 x86: ivybridge: Add PCH init
Add required init for the Intel Platform Controller Hub in ivybridge.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:00 -07:00
Simon Glass
3e0332c0b9 x86: Add a simple header file for ACPI
We don't use many features yet, so this only has a few declarations.
It will be expanded as needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:00 -07:00
Simon Glass
4e7a6acac7 x86: ivybridge: Add support for BD82x6x PCH
Add basic setup for the PCH.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:34:00 -07:00
Simon Glass
a0bd851ece x86: Set up edge triggering on interrupt 9
Add this additional init in case it is needed by the OS.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-25 06:34:00 -07:00
Simon Glass
e94ea6f656 x86: pci: Add handlers before and after a PCI hose scan
Some boards will want to do some setup before and after a PCI hose
is scanned.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-25 06:34:00 -07:00
Simon Glass
a2f5d091cc x86: Add ioapic.h header
Add definitions for the I/O Advanced Peripheral Interrupt Controller.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-25 06:33:59 -07:00
Simon Glass
65dd74a674 x86: ivybridge: Implement SDRAM init
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.

SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.

U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).

It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.

There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.

With this patch, link boots to a prompt.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:15 +01:00
Simon Glass
3eafce0527 x86: ivybridge: Add LAPIC support
The local advanced programmable interrupt controller is not used much in
U-Boot but we do need to set it up. Add basic support for this, which will
be extended as needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:15 +01:00
Simon Glass
1b4f25ff8e x86: ivybridge: Add support for early GPIO init
When not relying on Coreboot for GPIO init the GPIOs must be set up
correctly. This is currently done statically through a rather ugly method.
As the GPIOs are figured out they can be moved to the device tree and set
up as needed rather than all at the start.

In this implementation, board files should call ich_gpio_set_gpio_map()
before the GPIO driver is used in order to provide the GPIO information.
We use the early PCI interface so that this driver can now be used before
relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:14 +01:00
Simon Glass
8e0df066ff x86: ivybridge: Add early init for PCH devices
Many PCH devices are hard-coded to a particular PCI address. Set these
up early in case they are needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:14 +01:00
Simon Glass
77f9b1fb62 x86: ivybridge: Perform Intel microcode update on boot
Microcode updates are stored in the device tree. Work through these and
apply any that are needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:14 +01:00
Simon Glass
f5fbbe9579 x86: ivybridge: Perform initial CPU setup
Set up the flex ratio (controls speed versus heat output) and a few other
very early things.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:13 +01:00
Simon Glass
eddbad224b x86: Add msr read/write functions that use a structure
It is convenient to be able to adjust MSRs with a structure that splits the
two 32-bit halves into separate fields, as they are often dealt with
separately. Add a few functions to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:13 +01:00
Simon Glass
3f70a6f577 x86: Add clr/setbits functions
These are available on other architectures. Make them available on x86 also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:13 +01:00
Simon Glass
2b6051541b x86: ivybridge: Add early LPC init so that serial works
The PCH (Platform Controller Hub) includes an LPC (Low Pin Count) device
which provides a serial port. This is accessible on Chromebooks, so enable
it early in the boot process.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:12 +01:00
Simon Glass
6fb3b72e87 x86: pci: Allow configuration before relocation
Add simple PCI access routines for x86 which permit use before relocation.
The normal PCI stack is still used, but for pre-relocation use there can
only ever be a single hose. After relocation, fall back to the normal
access, although even then on x86 machines there is normally only a single
PCI bus.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:12 +01:00
Simon Glass
7430f10864 x86: Support use of PCI before relocation
Add support for using PCI before SDRAM is available, using early malloc()
and global_data.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:34:12 +01:00
Simon Glass
d188b18f65 x86: Refactor PCI to permit alternate init
We want access PCI earlier in the init sequence, so refactor the code so
that it does not require use of a BSS variable to work. This will allow us
to use early malloc() to store information about a PCI hose.

Common PCI code moves to arch/x86/cpu/pci.c and a new
board_pci_setup_hose() function is provided by boards to set up the (single)
hose used by that board.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:34:11 +01:00
Simon Glass
70a09c6c3d x86: chromebook_link: Implement CAR support (cache as RAM)
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:11 +01:00
Simon Glass
d1cd045982 x86: Emit post codes in startup code for Chromebooks
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.

On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:34:11 +01:00
Simon Glass
8ef07571a0 x86: Add chromebook_link board
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.

This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:34:11 +01:00
Simon Glass
727c1a9871 x86: Replace fill_processor_name() with cpu_get_name()
This implementation has a 'cpu' prefix and returns a pointer to the string,
avoiding the need for copying.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:24:12 +01:00
Simon Glass
003504b6fe x86: Remove unnecessary find_fdt(), prepare_fdt() functions
These are no-longer needed so drop them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:24:12 +01:00
Simon Glass
21b9b14b49 x86: Add processor functions to halt and get stack pointer
Add a function to get the stack pointer and another to halt the CPU.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21 07:24:12 +01:00