Add missing zynq_board_read_rom_ethaddr() prototype reported by sparse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This is the same patch as was done earlier.
Please look at Linux patch:
"arm64: zynqmp: Use only earlycon bootargs instead of full one"
(sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reference is needed for pinctrl driver where some signals can be
routed directly to platform management unit (PMU).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Using "cpu_pos_mask()" function to detect the real online cpus,
and discard the needless cpu nodes on kernel dts.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
This area of the image contains symbols whose values are filled in by
binman. If this feature is not used, the table is empty.
Add this to the ARM SPL link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
It is tedious to define both mask and bit-shift. <linux/bitfield.h>
provides a convenient way to get access to register fields with a
single shifted mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use DIV_ROUND_CLOSEST(). To make the JK value even more precise,
I used a bigger coefficient, then divide it by 512.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
missed to write the computed value to the SSCPLLCTRL2 register.
Fixes: 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the link error for the combination of
CONFIG_ARCH_UNIPHIER_LD11=n
CONFIG_ARCH_UNIPHIER_LD20=n
CONFIG_ARCH_UNIPHIER_PXS3=y
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77995 D3 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77970 V3M .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The TBS Tablet sports an LVDS display, an eMMC, an external SD, USB devices
and USB OTG.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 21f4486faa ("armv8: update gd after relocate") sets x18
without checking the return value of spl_relocate_stack_gd().
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Kever Yang <kever.yang@rock-chips.com>
CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is suplement for patch which handle below errata:
A-009007, A-009008, A-008997, A-009798
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Instruction prefetch feature is by default enabled during core
release. This patch add support of disabling instruction prefetch
by setting core mask in PPA. Here each core mask bit represents a
core and prefetch is disabled at the time of core release.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After updating dtc-1.4.5 version, there are too many warning.
This patch is to fix about exynos4 series.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After relocation, when error happends, it is hard to track
ELR and LR with asm file objdumped from elf file.
So subtract the gd->reloc_off the reflect the compliation address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove unnecessary DECLARE_GLOBAL_DATA_PTR and header includes.
<common.h> has been replaced with <linux/errno.h> and <linux/printk.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi
NEO2), which may not work properly at 1008MHz if the chip's quality is
not so good.
Lower the default CPUx frequency of H5 to 816MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the RK3399-Q7, we want to trigger a full platform reset (so the
various software stacks supported don't have to deal with the same
complexities over and over again) in case that anything other than a
power-on reset occurred.
To do so, this defines the /config/sysreset-gpio property and has it
point to a GPIO that will perform a power-on reset of the entire
platform.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
USB1 is connected to the on-module USB 3.0 hub and power to the hub
(actually it's a reset signal, modeled as a fixed regulator, that will
be released) should be enabled only during the first probing of the
device to avoid the hub from entering its low-power mode (where it
tries to attach on a fixed interval, but we always miss the timeslot
when U-Boot has the controller listening).
This adds a 'tsd,usb-port-power' stringlist to enable the
infrastructure in the board-specific usb_hub_reset_devices to find and
control the fixed regulator associated with control of the USB hub.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
According to rk3036 TRM, should be set to '1' for the pll
integer mode, while the '0' means the frac mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After the MASK MACRO update, we need to update the driver at the same time.
This is a fix to:
37943aa rockchip: rk3036: clean mask definition for cru reg
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There is a fixed div-2 between PLL and clk_ddr/clk_ddrphy,
so we need to double to pll output and then ddr can work
in correct frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
evb-rk3128 is an evb from Rockchip based on rk3128 SoC:
- 2 USB2.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3128 pinctrl driver and grf/iomux structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
RK3128 is a SoC from Rockchip with quad-core Cortex-A7 CPU
and mali400 GPU. Support Nand flash, eMMC, SD card, USB 2.0 host
and device, HDMI/LVDS/MIPI display.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Check if we are booting from NAND and let the bootrom
continue to load the rest of the bootloader
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
It's the first 8 bits of the bootrom error register that
contain the boot error/fallback error code. Let's check that
and continue to boot from UART.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
In U-Boot, this device tree is compatible with both the Torpedo and
SOM-LV kits. Let's rename it in the device tree since the U-Boot code and
show a more generic OMAP3 name. The code auto detects between the two and
loads the proper DTB file for Linux. This would eliminate the SOM-LV showing
the name Torpedo during boot and hopefully eliminate some confusion.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
MPU's region setup can be factorized between STM32F4/F7/H7 SoCs family
and used a common MPU's region config.
Only one exception for STM32H7 which doesn't have device area
located at 0xA000 0000.
For STM32F4, configure_clocks() need to be moved from arch_cpu_init()
to board_early_init_f().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Align the RCC compatible string with the one used by kernel.
It will allow to use the same clock driver for STM32F4
and STM32F7 and to manage the differences between the 2 SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This node is needed to enable performance mode
when system frequency is set up to 200Mhz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Implement DM driver for the Renesas PRR into RCar cpu info and convert
all users with DM and OF enabled to this new driver. This means all of
the boards with DM and OF enabled can fetch PRR address from DT, which
is useful on ie. V3M which has different PRR address than the rest of
Gen3 SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The checkboard() function showing hard-coded board model for which the
U-Boot was built is superseded on Gen3 by show_board_info() displaying
the Model from device tree. Add small ifdef to stop compiling the
function into U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since both R8A7795 and R8A7796 now use the same files, unify the
Makefile entry to CONFIG_RCAR_GEN3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Unify the R7A7795 and R8A7796 memory maps in memmap-gen3 and, for now,
select which one is used based on which SoC is selected. Since this is
done in C code instead of statically assigned now, the decision can be
taken by PRR SoC match as well, which will be done in a subsequent patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace the ad-hoc values in the PRR CPU ID table with macros,
so that users can use rmobile_get_cpu_type() can compare the
returned value with these macros to figure out on which CPU they
are running.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These files no longer contain anything useful, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These old PFC tables are no longer needed as there is now a proper
PFC pinmux driver in drivers/pinctrl/renesas . Remove them .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the RCar Gen3 no longer uses the SH SDHI driver, but rather
uses the Matsushita SD driver, which loads all the properties from
device tree, these macros are no longer used, remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for ULCB to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
=BqNN
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Putting board_nand_init() function inside NAND driver was not appropriate
due to it doesn't allow board vendor to customise their NAND
initialization code such as adding NAND lock/unlock code.
This commit was to move the board_nand_init() function from NAND driver
to board.c file. This allow customization of board_nand_init() function.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sparse is return warning about this:
arch/arm/mach-zynq/slcr.c: In function 'zynq_slcr_get_mio_pin_status':
arch/arm/mach-zynq/slcr.c:185:16: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add proper support for EMIT_WRITE operation which is write only.
Do not use EMIT_MASKWRITE which is read-modify-write.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is based on work done in topic board where the first address
word also storing operation which should be done. This is reducing size
of configuration data.
This patch is not breaking an option to copy default ps7_init_gpl* files
from hdf file but it is doing preparation for ps7_init* consolidation.
The patch is also marking ps7_config as weak function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing declaration to header.
Warning log:
arch/arm/mach-zynq/spl.c:94:12: warning: symbol 'ps7_post_config' was
not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This work-around has been here in U-Boot because the AIDET and GPIO
drivers were missing in the upstream Linux. Both are now available
in Linus' tree:
- drivers/irqchip/irq-uniphier-aidet.c
- drivers/gpio/gpio-uniphier.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable watchdog in dts for zcu102.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes SMMU work by moving the iommus node under the dwc3 child
entry from parent node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch uncomments snps,quirk-frame-length-adjustment which has
the value to adjust the SOF/ITP generated from the controller.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds OTG interrupt support in device tree. It will add
an extra interrupt line number dedicated to OTG events. This will
enable OTG interrupts to serve in DWC3 OTG driver.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds CCI support for USB when CCI is enabled in design.
This patch also adds 'reg' property for Xilinx USB 3.0 IP. The 'reg'
property is added in order to modify a register in that to enable
coherency in Hardware.
Also add address to unit name to avoid dtc warning
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for reading silicon revision using zynqmp nvmem
driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.
Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch sets host quirk2 bit field for No 1.8V supported in case of
1.0 silicon. The 1.0 silicon doesn't have support for UHS-I modes. This
property will ensure the SD runs on High Speed mode.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the phy_zynqmp.c driver to use reset-controller
framework for asserting/de-asserting reset for High Speed modules.
Also fix documentation and dtsi.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add the reset nodes in zynqmp.dtsi which are used by
reset-controller framework
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Only silicon v1 requires this termination fix. With new nvmem soc
revision nvmem detection driver this can be autodetected at run time and
this flag is not needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for zynqmp nvmem firmware driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added pin control support in device tree for zynqmp.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc reports issues with it.
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Used defines rather than raw values for gpio configurations.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some user space libraries reading platform compatible string and based
on that changing behavior. Mark revB board with revB string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently DP power domain (pd_dp) is not attached to any of the DP nodes which is
causing genpd to trigger a power down request for DP domain, making all DP related
peripherals unusable. So assign power domains for all DP related nodes to enable
proper accounting of DP power domain usage.
Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch disables the smmu and also removes the mmu-masters
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the calibration property with required value,
calculated based on rtc input crystal oscillator frequency (32.768Khz).
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All gpio controllers should contain this property.
This property is not checked by the code that's why this issue wasn't
found earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The correct register size is 0x10000, otherwise
it overlaps with other register space.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch will add names to the clocks used by GPU.
Signed-off-by: Madhurkiran Harikrishnan <madhurki@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This will simplify dt overlay structure for the whole PL.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract from Linux mainline patch:
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.
These efuse bits are setup for certain devices.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
A53 can do speculative and may result in ECC failures
if TCM's are not initialized. So, it is always better
to disable dcaches before accessing TCM and enable back.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.
Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In
if (a || b)
else if (!a)
the constraint (!a) is always true if else is reached and
can be removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3
Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.
Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome. Instead this check can easily be performed in
the C-code.
This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.
Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 has a total of 9 I2C controllers. To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.
For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Enter download mode if the download key pressed.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Converted printfs in boot_mode.c to debug/pr_err:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig. This migrates those over to
Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it. There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.
All the existing call-sites are adjusted to match the changed function
signature.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.
With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.
Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.
This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers. One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.
To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32. By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.
Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).
This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.
To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 5
- ran 'whitespace-cleanup'
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
instruction load and running by bootrom;
Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.
To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
(1) if a boot0-hook is present it is inserted at the start of
the image
(2) if a boot0-hook is present, emitting the ARM vector table
(and the _start) symbol are suppressed in vectors.S and
the boot0-hook has full control over where and when it
wants to emit these
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mark bandgap node as uboot,dm-spl so that it can be accessed in spl
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a driver for the I2C controller available on Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.
Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
We need to update gd in assamble code after relocate,
this is a fix to:
adc421e arm: move gd handling outside of C code
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
