Commit graph

103 commits

Author SHA1 Message Date
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Lubomir Popov
ee28edac43 OMAP5: Enable access to auxclk registers
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.

Also remove unrelated TPS62361 defines from clocks.h

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10 08:54:46 -04:00
Sricharan R
92b0482c17 ARM: DRA7xx: EMIF: Change settings required for EVM board
DRA7 EVM board has the below configuration. Adding the
settings for the same here.

   2Gb_1_35V_DDR3L part * 2 on EMIF1
   2Gb_1_35V_DDR3L part * 4 on EMIF2

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
e9d6cd042d ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc's
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Nishanth Menon
18c9d55ac6 ARM: OMAP5: DRA7xx: support class 0 optimized voltages
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.

This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.

This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
63fc0c775c ARM: DRA7xx: power Add support for tps659038 PMIC
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
4ca94d8186 ARM: OMAP4+: pmic: Make generic bus init and write functions
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
4d0df9c1e9 OMAP3+: introduce generic ABB support
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:

* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
  performance at the cost of power.  Used to operate safely at high
  OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
  save power.  Used to save power at lower OPPs.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2013-06-10 08:43:09 -04:00
Tom Rini
edfcf85a0a am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>
The location of valid scratch space is dependent on SoC, so move that
there.  On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR.  On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space.  Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-06 08:57:45 -04:00
SRICHARAN R
4a0eb75752 ARM: OMAP: Cleanup boot parameters usage
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
fda06812a0 ARM: OMAP: Correct save_boot_params and replace with 'C' function
Currently save_boot_params saves the boot parameters passed
from romcode. But this is not stored in a writable location
consistently. So the current code would not work for a
'XIP' boot. Change this by saving the boot parameters in
'gd' which is always writable. Also add a 'C' function
instead of an assembly code that is more readable.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
f92f2277a6 ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines common
These defines are same across OMAP4/5. So move them to
omap_common.h. This is required for the patches that
follow.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
Lokesh Vutla
0b1b60c779 ARM: OMAP5: Fix warm reset with USB cable connected
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-05-10 08:25:55 -04:00
Lokesh Vutla
de62688bb6 arm: dra7xx: Add silicon id support for DRA752 soc
Adding CPU detection support for the DRA752 ES1.0 soc.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:39:57 -04:00
Lokesh Vutla
8b12f1779e arm: dra7xx: Add control module changes
Control module register addresses are changed from OMAP5
to DRA7XX socs.
So adding the necessary changes for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
ea8eff1fe0 arm: dra7xx: clock: Add the dplls data
A new DPLL DDR is added in DRA7XX socs. Now clocks to
EMIF CD is from DPLL DDR. So DPLL DDR should be locked
before initializing RAM.
Also adding other dpll data which are different from OMAP5 ES2.0.
SYS_CLK running at 20MHz is introduced in DRA7xx socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4e4129c31 arm: dra7xx: clock: Add the prcm changes
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX.
So adding the necessary register changes for DRA7XX socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4d986ee27 ARM: OMAP5: srcomp: enable slew rate compensation cells after powerup
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
	 The 1 in wkup domain is not enabled because smart i/os
	 of wkup domain work with default compensation code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
SRICHARAN R
47abc3df70 ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendum
Change OPP settings as per the latest 0.5 version of
addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched
here to add dummy dividers.

While here correcting OPP_NOM mpu, core frequency for
OMAP4430 ES2.x

Note that OMAP5430 ES1.0 support is still kept alive and
would be removed in a cleanup later.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
afc2f9dcf1 ARM: OMAP5: clock: Add the prcm register changes required for ES2.0
PRCM register addresses are changed from ES1.0 to ES2.0 due to
PER power domain getting moved to CORE power domain.

So adding the nessecary register changes for the same.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
eed7c0f727 ARM: OMAP5: Add silicon id support for ES2.0 revision.
Adding the CPU detection suport for OMAP5430 and
OMAP5432 ES2.0 SOCs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2013-03-11 11:06:10 -04:00
Lokesh Vutla
c43c8339fe ARM: OMAP4+: Make control module register structure generic
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
3fcdd4a5f8 ARM: OMAP4+: Clean up the pmic code
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
ee9447bfe3 ARM: OMAP4+: Cleanup the clocks layer
Currently there is quite a lot of code which
is duplicated in the clocks code for OMAP 4 and 5
Socs. Avoiding this here by moving the clocks
data to a SOC specific place and the sharing the
common code.

This helps in addition of a new Soc with minimal
changes.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:09 -04:00
SRICHARAN R
01b753ff7b ARM: OMAP4+: Change the PRCM structure prototype common for all Socs
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.

Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11 11:06:09 -04:00
Tom Rini
f0881250f9 ARM: SPL: Make spl_mmc.c more generic
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>.  Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:58 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Tom Rini
8082fda9fc ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.c
This detection code doesn't (and can't) do anything currently, so
remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
37189a1958 ARM: SPL: Rename omap_boot_mode to spl_boot_mode()
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
8e1b836ec5 ARM: SPL: Rename omap_boot_device to spl_boot_device
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Tom Rini
861a86f460 omap-common: SPL: Add CONFIG_SPL_DISPLAY_PRINT / spl_display_print()
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing.  Change how this works to
be opt-in and only turned on for omap4/5 now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Tom Rini
0689a2ef19 am33xx: Correct MMC1, remove MMC2 support
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Lokesh Vutla
0a0bf7b217 OMAP5: ADD chip detection for OMAP5432 SOC
This patch adds chip detection for OMAP5432

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07 14:07:23 +02:00
Balaji T K
f75231b79a arm: omap5: correct boot device mode7 for eMMC
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:25 +02:00
SRICHARAN R
087189fb54 OMAP4/5: Make the silicon revision variable common.
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:24 +02:00
Simon Schwarz
379c19ab70 omap-common/spl: Add linux boot to SPL
This adds Linux booting to the SPL

This depends on CONFIG_MACH_TYPE patch by Igor Grinberg
(http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809)

Related CONFIGs:
CONFIG_SPL_OS_BOOT
	Activates/Deactivates the OS booting feature
CONFIG_SPL_OS_BOOT_KEY
	defines the IO-pin number u-boot switch - if pressed u-boot is
	booted
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
	Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
	Address where the kernel boot arguments are expected - this is
	normaly RAM-begin + 0x100

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Simon Schwarz
9e70c08b6f devkit8000/spl: init GPMC for dm9000 in SPL
Linux crashes if the GPMC isn't configured for the dm9000.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Matt Porter
24de357a30 SPL: Add YMODEM over UART load support
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Andreas Müller
761ca31e47 omap_rev_string: output to stdout
* avoid potential buffer overflows
* allow SPL-build not to output "Texas Instruments Revision detection unimplemented"

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Tom Rini
ee08a8260a OMAP3: Add SPL_BOARD_INIT hook
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c.  OMAP4
doesn't need i2c enabled in SPL.  Enable SPL_BOARD_INIT on devkit8000.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Aneesh V
9404758e9b omap4460: add ES1.1 identification
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Tom Rini
cc3f705843 OMAP3 SPL: Provide weak omap_rev_string
We add an weak version of omap_rev_string in omap-common/spl.c
and while at it drop the omap3 version.  Move the prototype over
to <asm/omap_common.h> with the other SPL functions.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:35 +02:00
Sandeep Paulraj
d6cac9c83d devkit8000: Fix build break
Found a build erros when i ran MAKEALL.
So fix it.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:55 +02:00
Simon Schwarz
bb085b87e5 omap-common: add nand spl support
Add NAND support for the new SPL structure.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:54 +02:00
Aneesh V
8cf686e19b omap: add MMC and FAT support to SPL
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
  can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
  and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
  payload size and load address from this header. If the
  header is not detected assume u-boot.bin as payload

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
bcae721162 omap: add basic SPL support
- Provide alternate implementations of board_init_f()
  board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
  it to board config header from config.mk

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
3776801d0a omap4: add clock support
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails

This work draws upon previous work done for x-loader by:
	Santosh Shilimkar <santosh.shilimkar@ti.com>
	Rajendra Nayak <rnayak@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Aneesh V
d2f18c275e omap4: utility function to identify the context of hw init
The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
 1. SPL running from SRAM
 2. U-Boot running from FLASH
 3. Non-XIP U-Boot loaded to SDRAM by SPL
 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
    Configuration Header feature

What level of hw initialization gets done depends on this
context. Add a utility function to find this context.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00