U-boot proper can use frame buffer address passed from SPL to reserve
the memory area used by framebuffer set in SPL so that splash image
set in SPL continues to get displayed while u-boot proper is running.
Put the framebuffer address and size in a bloblist to make them
available at u-boot proper, if in u-boot proper CONFIG_VIDEO is defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At SPL stage when stack is relocated, the stack pointer needs to be
updated, the stack pointer may point to stack in on chip memory even
though stack is relocated.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
During compilation splash_source puts out below warning for type
conversion in splash_load_fit for bmp_load_addr and fit_header.
Change their type to uintptr_t to fix the warnings.
common/splash_source.c: In function ‘splash_load_fit’:
common/splash_source.c:366:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
366 | img_header = (struct legacy_img_hdr *)bmp_load_addr;
| ^
common/splash_source.c:376:49: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
376 | res = splash_storage_read_raw(location, (u32)fit_header, fit_size);
| ^
common/splash_source.c:401:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
401 | memmove((void *)bmp_load_addr, internal_splash_data, internal_splash_size);
The above warnings are generated if CONFIG_FIT is enabled.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Some devices keep 2 copies of the bootloader_message in the misc
partition and write each in sequence when updating. This ensures that
there is always one valid copy of the bootloader_message. Teach u-boot
to optionally try a backup bootloader_message from a specified offset if
the primary one fails its CRC check.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
The output is garbled when tiny printf() is used. Correct this by adding
a special case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When video is set up in SPL, U-Boot proper needs to use the correct
parameters so it can write to the display.
Put these in a bloblist so they are available to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to see the base of the malloc region. This is visible when
debugging but not in normal usage.
Add it to the global data so that it can be shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
At present this leaves the stack at the pre-relocation value. This is not
ideal since we want to have U-Boot running entirely from the top of
memory.
In addition, the new global_data pointer is not actually used, since
the global_data pointer itself is relocated, then the pre-relocation value
is changed, so the effective value (after relocation) does not update.
Adjust the implementation to follow the 32-bit code more closely, with a
trampoline function which is passed the new stack and global_data pointer.
This ensures that the correct values come through even when relocating.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a bit more detail so it is clear that multiple devices are
supported, but only one per driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In case of OF_SEPARATE (!OF_EMBED), the devicetree blob is placed
after _end, and fdt_find_separate() always returns _end. There is
a .bss section after _end and the section is cleared before relocation.
When GD_FLG_SKIP_RELOC is set, relocation is skipped, so the blob is
still in .bss section, but will be cleared. As a result, the devicetree
become invalid.
To avoid this issue, should relocate it regardless of GD_FLG_SKIP_RELOC
in reloc_fdt().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
memalign() returns a pointer which is to be freed by free(). To call
unmap_sysmem() is incorrect, furthermore it was called in a wrong scope.
Also add a check for allocation error.
Fixes: d7af2baa49 ("crypto/fsl: Fix HW accelerated hash commands")
Cc: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This feature is different enough from bootstd that it probably deserves
its own log category. It cannot use a uclass since it is not a device.
Add a new category.
Signed-off-by: Simon Glass <sjg@chromium.org>
As implemented in the arch/arm/mach-rockchip/tpl.c file,
the CONFIG_TPL_BANNER_PRINT option will not work
if either of these options is not enabled.
Add dependency constraints to the CONFIG_TPL_BANNER_PRINT option
definition to prevent configuration problems
where option is enabled but do not take effect.
Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
CONFIG_SYS_CONSOLE_ENV_OVERWRITE is implemented in common/console.c
when "#if CONFIG_IS_ENABLED(SYS_CONSOLE_IS_IN_ENV)" is met.
It is recommended to add dependency constraints to its definition.
Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
Describe which numeric values can be used for as scratch options for
OpenSBI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, spl_end points to the __bss_end address, which
is an external RAM address instead of the end of the SPL text
section in the internal RAM.
This causes boot failures on imx6-colibri, for example:
```
Trying to boot from MMC1
SPL: Image overlaps SPL
resetting ...
```
Fix this problem by assigning spl_end to _image_binary_end, as this
symbol properly represents the end of the SPL text section.
From u-boot-spl.map:
.end
*(.__end)
0x00000000009121a4 _image_binary_end = .
Fixes: 77aed22b48 ("spl: spl_legacy: Add extra address checks")
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # DH i.MX6Q DHCOM PDK2
The current mechanism is unnecessarily complex. Simplify the whole mechanism
such that the entire fitImage is signed, IVT is placed at the end, followed
by CSF, and this entire bundle is also authenticated. This makes the signing
scripting far simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
The intent here was to allow ANSI codes to be disabled, since it was
proving impoosible to test operation of the menu code when it kept moving
the cursor. Unfortunately this ended up in the patch.
Correct this by enabling ANSI again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pali Rohár <pali@kernel.org>
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Fixes: 32bab0eae5 ("menu: Make use of CLI character processing")
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Ensure that every write is flushed to memory and afterward reads are
from memory.
Since the algorithm rely on the fact that accessing to not existent
memory lead to write at addr / 2 without this modification accesses
to aliased (not physically present) addresses are cached and
wrong size is returned.
This was discovered while working on a TI AM625 based board
where cache is normally enabled, see commit c02712a748 ("arm: mach-k3: Enable dcache in SPL").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
If only FIT images are enabled and loading the FIT image fails,
spl_nor_load_image() should return an error instead of zero.
Without this patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
Unsupported OS image.. Jumping nevertheless..
image entry point: 0x0
With patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
SPL: failed to boot from all boot devices (err=-6)
.### ERROR ### Please RESET the board ###
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Add support to load the next stage image from an NVMe disk which may
be formatted as an EXT or FAT filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
[trini: Drop hunk changing disk/part.c as that breaks other users]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a generic API to support loading of SPL payload from any supported
filesystem on a given partition of a block device.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Add kconfig options to enable NVME and PCI NVMe support in SPL
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new function fdt_copy_fixed_partitions to copy the fixed
partition nodes from U-Boot device tree to Linux kernel
device tree and to dynamically configure the MTD partitions.
This function fdt_copy_fixed_partitions is only based on device tree
with livetree compatible function and replace the function
fdt_fixup_mtdparts based on mtdparts variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch is a preliminary patch to use ofnode function
is fdt_support to read the U-Boot device tree with livetree
compatible functions.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 9905cae65e ("fs: ext4: check the minimal partition size
to mount"), a valid size needs to be provided when mounting
an ext filesystem. Fix the spl ext driver to use the parition size
instead of 0 when mounting the filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Invoking the sandbox with
/u-boot -c ⧵0xef⧵0xbf⧵0xbd
results in a segmentation fault.
Function b_getch() retrieves a character from the input stream. This
character may be > 0x7f. If type char is signed, static_get() will
return a negative number and in parse_stream() we will use that
negative number as an index for array map[] resulting in a buffer
overflow.
Reported-by: Harry Lockyer <harry_lockyer@tutanota.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per the fit_conf_get_node() API doc, it returns configuration node
offset when found (>=0).
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add method to remove video driver before loading u-boot proper. When
bootstage changes from SPL to u-boot proper, noo method is called to
remove video driver, and at u-boot proper if video driver is not
enabled, the video driver starts displaying garbage on the screen,
because there is no reserved space for video and the frame buffer gets
u-boot proper data written.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Fix comments error in EVENT_DEBUG description:
this get usefui -> this to get useful
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The u-boot hush shell doesn’t support the unset command to clear a
variable and therefore an empty value ("c=") should be a valid value
for the set_local_var function to clear the variable. This partial
reverts commit aa72252963 ("common: cli_hush: avoid dead code") and
only checks for a `=` in the string. Additionally explicit call the
unset_local_var function to remove the variable if the value is empty.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function fdt_simplefb_enable_existing_node() should be static as it is not
used outside common/fdt_simplefb.c.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Avoid using preprocessor compilation directives and instead use simple
logical expressions for better readability since compiler will anyway
optimize out the respective code block if condition is not satisfied.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
To support splash screen at both u-boot proper and SPL use
CONFIG_IS_ENABLED and CONFIG_VAL to check for video related Kconfigs at
respective stages.
Replace CONFIG_CMD_BMP with CONFIG_BMP to enable splash_display function
at u-boot proper and SPL.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add rule to compile bmp.c at SPL and u-boot proper when CONFIG_SPL_BMP
and CONFIG_BMP are defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
To enable splash screen at SPL, need to compile cmd/bmp.c which also
includes bmp commands, since SPL doesn't use commands split bmp.c into
common/bmp.c which includes all bmp functions and cmd/bmp.c which only
contains bmp commands.
Add function delclaration for bmp_info in video.h.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_BMP and CONFIG_SPL_BMP which enable displaying bmp images at
u-boot proper and SPL.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
To enable splash screen and loading bmp from boot media, add rules to
compile splash.c and splash_source.c at SPL stage only when
CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_SPLASH_SOURCE are defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The QEMU emulation of m68k does not support DMA timer, the only
timer that is supported is the PIT timer. Implement trivial PIT
timer support for m68k.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Mask macro PART_ACCESS_MASK filter out access bits of emmc register and
macro EXT_CSD_EXTRACT_BOOT_PART() extracts boot part bits of emmc register.
So use EXT_CSD_EXTRACT_BOOT_PART() when extracting boot partition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
* vsnprintf() can truncate cmd, hence it makes no sense to launch such
command (it's broken). Moreover, it's better to signalize to the caller
about such case (for facilitating debugging or bug hunting).
* Fix kernel-doc warnings:
include/command.h:264: info: Scanning doc for run_commandf
include/command.h:268: warning: contents before sections
include/command.h:271: warning: No description found for return value
of 'run_commandf'
* Add printf-like format attribute to validate at compile-time the format
string against parameters's type.
* Fix compilation error in case of -Wall, -Werror, -Wextra:
error: variable ‘i’ set but not used [-Werror=unused-but-set-variable]
* Drop extra ret variable.
Signed-off-by: Evgeny Bachinin <EABachinin@sberdevices.ru>
Reviewed-by: Simon Glass <sjg@chromium.org>
The second call to cli_ch_process() is in the wrong place, meaning that
the one of the characters of an invalid escape sequence is swallowed
instead of being returned.
Fix the bug and add a test to cover this.
This behaviour matches that of the code before cli_getch() was
introduced. This was verified on the commit before b08e9d4b66 i.e.:
7d850f85aa ("sandbox: Enable mmc command and legacy images")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This function does not behave as expected when unknown escape sequences
are sent to it:
- it fails to store (and thus echo) the last character of the invalid
sequence
- it fails to set esc_len to 0 when it finishes emitting the invalid
sequence, meaning that the following character will appear to be part
of a new escape sequence
- it processes the first character of the rejected sequence as a valid
character, just starting the sequence all over again
The last two bugs conspire to produce an "impossible condition #876"
message which is the main symptom of this behaviour.
Fix these bugs and add a test to verify the behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With clang-15 we now will get warnings such as:
warning: a function declaration without a prototype is deprecated in all
versions of C [-Wstrict-prototypes]
And it is easy enough to address this warning here, as we aren't
concerned with re-syncing with an upstream.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
binman signing feature
fix buildman -A bug introduced recently
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmQQ8KIRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYRmwgA1XAHafEOfhaya54nalUgW9qYZe5Ntfqd
4Tg7zj3gadZuv82LuyskEyBKptwRCzgX0Tyx62V3Oop9vJ/cCwjIB4AGhCsMKERf
NqcMd8fbGbJ9jJzOp7gNTHzV4vSmwKM0lRkxbClMFcvMsfVdKcBRPswLLghk5/xL
Uu4Ww4yfe7UCqgBm9uouVaIbcNNcl8p0QnSJT9HvwjGKawPT6uSHOHK9Wpkud0q1
ZyrPpCMA29mifhIU8aH5CJH5G61UbGcVSDhm9lIKwqZg+KJGuYf64JbZoY9JI2/z
pOUHLZx7fVHoFyWKWfVkA9l6HRjZTRc0nJhYFx5HyNUOU50hMENeTQ==
=ko2P
-----END PGP SIGNATURE-----
Merge tag 'dm-next-12mar23a' of git://git.denx.de/u-boot-dm into next
More tests and fixes for fdt command
binman signing feature
fix buildman -A bug introduced recently
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce proof of concept for binman's new option which provides sign
and replace FIT containers in binary images.
Usage as example:
from:
mkimage -G privateky -r -o sha256,rsa4096 -F fit
binman replace -i flash.bin -f fit.fit fit
to:
binman sign -i flash.bin -k privatekey -a sha256,rsa4096 -f fit.fit fit
and to this one if it's need to be extracted, signed with key and put it
back in image:
binman sign -i flash.bin -k privatekey -a sha256,rsa4096 fit
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
In case character 0x20 (space) is used as line separator,
character 0x9 (tab) is treated end of line. Commands which
output a lot of tabs, i.e. various tree printing commands
like 'fdt print' then end up generating a lot of newlines
in the recorded output, and the recorded output is corrupted.
Use character 0x00 (NUL) as separator instead to treat the
tabs as valid part of recorded line.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes: 5454dea313 ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
USB hubs run in host mode not in gadget mode. Hence, compiling usb_hub.c
should not be selected by CONFIG_USB_GADGET.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This needed for unit testing different fonts.
Configured fonts are placed in an array of fonts.
First font is selected by default upon console probe.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agust: fixed build error when bmp logo disabled]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We can use this feature in VPL, so add some options for it. Also fix a
typo in the SPL help while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
As platforms which require this hook need this hook enabled, in order to
function, or do not need this hook, it doesn't make sense to prompt the
user. As all platforms that need this hook now select the symbol, remove
the prompt text.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While it is true that for some Samsung platforms, we call
get_board_type() the main usage of this CONFIG switch is to enable
board_types in global data, which is then used by various platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On some platforms is SYS_MMCSD_FS_BOOT_PARTITION unsupported. So allow to
completely disable MMC FS Boot support via new option SYS_MMCSD_FS_BOOT.
By default MMC FS Boot support is enabled (like it was before) except for
ARCH_MVEBU where MMC FS Boot supported is unsupported due to Marvell
BootROM limitations.
Signed-off-by: Pali Rohár <pali@kernel.org>
The arg->session is not valid if arg->ret != NULL, so can't be
assigned, correct this.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@globallogic.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Add a CONFIG option to deal with this automatically, printing a warning
when U-Boot starts up. This can be useful if the device tree comes from
another project.
We will maintain this through the 2023.07 release, providing 6 months
for people to notice.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 4:
Acked-by: Michal Simek <michal.simek@amd.com>
Reset the serial flags so that the debug UART can be used (if enabled)
in the small window where there is no serial device. This can avoid a hang
in some cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change was made for the benefit of RISC-V but broke other
architectures also. In particular, tracing cannot work without this value.
Add it back for architectures which support it.
Fixes: 3c9fc23c44 ("sandbox: don't refer to symbol _init")
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
-----BEGIN PGP SIGNATURE-----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=HVHT
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc2
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 10 Feb 2023 12:15:45 PM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_VIDEO defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_SPLASH_SOURCE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SAVE_PREV_BL_INITRAMFS_START_ADDR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SAVE_PREV_BL_FDT_ADDR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_OF_EMBED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_NEEDS_MANUAL_RELOC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_HUSH_PARSER defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The change boot order menu in eficonfig can have at most INT_MAX lines
and it is troublesome to scroll down to the "Save" entry.
This commit assigns CTRL+S to save the boot order.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_SHA1SUM defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_HASH defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This is currently in the cmd/ file but we want to call it from a driver.
Move it into a common place. Tidy up the header-file order while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to log things related to filesystems. Add a new
category and place it at the top of one of the FAT files.
Signed-off-by: Simon Glass <sjg@chromium.org>
This was added by mistake and renders the function useless. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 33c60a38bb ("trace: Use notrace for short")
Reported-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
This matches how this would be done in Linux and these functions
do the alignment for us which makes the code look cleaner.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We can enforce the dependencies of this module via Kconfig now, so do so
rather than with #error statements. Further, we can ensure that all
required values are set to their defaults in Kconfig, and in fact
already do so, so remove the tests here. The exception is
CONFIG_UPDATE_LOAD_ADDR which needed to be migrated to Kconfig in the
first place.
Signed-off-by: Tom Rini <trini@konsulko.com>
In this case, using IS_ENABLED(...) to attempt to load the image results
in harder to read and less useful code, along with having to define a
CONFIG value that would be unused. To maintain the current albeit
slightly odd behavior, maintain that if we have both SPL_FS_FAT and
SPL_SATA_RAW_U_BOOT_USE_SECTOR enabled, we use SPL_FS_FAT for the load.
Signed-off-by: Tom Rini <trini@konsulko.com>
