-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl5nWr8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGaOCACkavhqX4EP1FeRDX7m
Uujnacekt0y0uC54aGqBZ2u8Y+iwFza7rd4RcWOAx1pHq1QggAF+h5So8cOfSjpD
6Uad4ql0EOYuH5xcFYCzmEmOMj25DrIZ0F+nPnxhdK0novBrUO8QD2v4r8TgrcWs
dFxe7RCvop4I54Bq14LzZsCozlYEqHaf5E3fSas2LVeDIBrkzGh6pYhWM62FFRuy
71kIC+y9pfRPXaeiOSDp1ZqPkzQA8xw5AWAx4TCmTZ1DjLLBAoRbe0Iv9fseHct0
BFGD4+G1g0GfrNrjAG2OPAePDXq+6fmoAZFbkDGeoFwGnZXhxEnVnN4w5t+Hl0H4
82tF
=eO+8
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Booting a mainline kernel in secure mode on i.MX7D causes only
one CPU to be brought up.
Change it to booting in non secure mode by default, which
allows the two CPUs to be brought up.
It does have a side effect of not probing the CAAM driver.
If CAAM driver is needed then a secure world OS such as OPTEE needs
to be used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
With CONFIG_SUPPORT_EMMC_BOOT moved to Kconfig, move it to defconfig
files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd0 ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> fastboot 0
$ fastboot flash rootfs rootfs.img
Fixes: 8fa7f65dd0 ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
DFU over TFTP flashing method might be helpful in order to speed-up the
flashing process of big images (as DFU works over USB EP0, which is
quite slow). Also, it's a good backup option in the case when USB got
broken (either in software or hardware), to avoid resorting to SD card
boot.
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd0 ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> setenv ipaddr 192.168.0.100
=> setenv serverip 192.168.0.1
=> setenv updatefile update_uboot.itb
=> dfu tftp mmc 1
Where 'update_uboot.its' file looks like this:
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
u-boot.img.raw-1 {
description = "U-Boot binary";
data = /incbin/("u-boot.img");
compression = "none";
type = "firmware";
load = <0x60000>;
hash-1 {
algo = "sha1";
};
};
};
};
And 'update_uboot.itb' is generated as follows:
$ mkimage -f update_uboot.its update_uboot.itb
Newly flashed U-Boot works fine.
Fixes: 8fa7f65dd0 ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Enable ESM modules for both PMIC and SoC side for proper watchdog
handling on the board.
SPL_BOARD_INIT is also enabled so that the board init function
probing the drivers is called.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Remove saving ENV in eMMC in R5 as the power domains are not
setup. Environment in eMMC cannot be read if we do not boot from
eMMC.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Enable R5F remoteproc support in R5 defconfig so that R5s can
be started in SPL. While at it enable the SPL_FS_EXT4 config
option to load the firmwares from file system.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
-----BEGIN PGP SIGNATURE-----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=h4lQ
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
The board uses 100 MHz clock for UART bitrate generator,
but is configured as 50 MHz on defconfig.
This produces wrong console output.
The first message, "Debug uart enabled" is received as:
"������b"
Fix the issue by configuring the correct clock for the
UART baudrate generator
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This fixes the inadvertent definition of CONFIG_DTB_RESELECT and
CONFIG_MULTI_DTB_FIT in the K2x HS defconfigs, that happened as part of
a resync of the defconfigs.
The inclusion of these config options causes ethernet to stop working on
K2x HS devices as they interfere with the installation of the secure
boot monitor.
This patch also removes the above configs for the K2 GP devices, as they
are not needed, and to keep the differences between the GP and HS
defconfigs to a minimum.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.
Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 02dc1599ba
Commit 02dc1599ba ("configs: enable sata, eSDHC, USB device module in
T2080QDS")
has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Add mmc device partition 0 as the seat of the environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.
Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable DM thermal driver and iMX thermal driver to get accurate
CPU frequency reporting in the boot log.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The CONFIG_DM_74X164 symbols should be moved to the defconfig file,
as indicated in the comments.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This partially reverts changes by commit 2cc393f32f
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DFU, Fastboot and USB mass storage gadget related configs
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable USB Gadget for R5 SPL, A72 SPL and A72 U-Boot to support DFU boot
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Increase R5 SPL early malloc memory pool by ~7K to accommodate SPL USB
DFU boot requirements
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current environment offset overlaps with the sysfw area and whenever
environment is saved in the redundant slot, it overwrites sysfw.itb. Fix
the offset to prevent this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Unit test for 'abootimg' command. Right now it covers dtb/dtbo
functionality in Android Boot Image v2, which was added recently.
Running test:
$ ./test/py/test.py --bd sandbox --build -k test_abootimg
shows that 1/1 tests passes successfully.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SFI is quite poor and useless resource provider. Moreover it makes hard
to develop and extend functionality in the Linux kernel.
Enable a necessary minimum to use ACPI on Intel Edison.
Linux kernel have been prepared for this change since v5.4, where the last
crucial driver, i.e. for Basin Cove PMIC, has been submitted.
Note, that stock image won't suffer by this change since it doesn't have
ACPI enabled on the kernel level.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable command line editing, because it is extremely convenient.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Migrate CONFIG_DESIGNWARE_WATCHDOG to Kconfig and update the headers
accordingly, no functional change. The S10 enables the WDT only in
SPL, but does not enable it in U-Boot itself, hence disable it in
the config again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
This enables readning the cpuid from e-fuse, and deriving a static
MAC address from it.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip use CONFIG_SPL_OPTEE for OPTEE support, which is load and run
before U-Boot, but not use CONFIG_OPTEE which is after U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Raspberry Pi 4 SoC features an integrated Gigabit Ethernet
controller, connected as a platform device.
Enable the new driver in the three applicable defconfigs, to allow
TFTP booting on the board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
[Andre: Add joined and 32-bit configs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable support for DFU over USB. This requires to enable USB gadget,
DWC2 UDC OTG driver and DFU command. DFU entities are defined for the
following firmware objects: u-boot.bin, uboot.env, config.txt, and
zImage/Image.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Orange Pi Win has gigabit ethernet port, but default U-Boot
configuration for that board enabled ethernet driver but
didn't enable realtek phy.
Fix that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch includes the following:
1. Add fastboot command to erase the whole EMMC_USER
2. Add fastboot command to flash image at EMMC_BOOT1
3. Add fastboot command to erase the whole EMMC_BOOT1
4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.
So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB
support for the two R40 boards U-Boot supports.
For this we need to add the GPIO pin that powers the USB port(s), also
enable the usual suspects (OHCI/EHCI support).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The M2 Berry features the normal Gigabit PHY connected to the SoC's MAC,
so enable the sun8i-emac driver to support Ethernet on the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS1028A QDS boards have a MDIO MUX and they require the driver for it for
PHYs to work.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
setexpr command is used while running secure boot
(chain of trust with confidentiality) feature.
Enable CONFIG_CMD_SETEXPR to enable setexpr command.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 and rev2 SoC has different pcie controller.
The pcie controller device tree node fields "compatible"
and registers names needs to be updated accordingly.
Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt
which updates the "compatible" and registers names.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Common device tree fixup for NXP SoCs. Based on
SoC and revision call pcie_layerscape or pcie_layerscape_gen4
fixup.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1012afwry
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1088ardb
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1046afrwy
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable USB keyboard to be used as input device at U-Boot prompt. Both
serial and USB keyboard will be active inputs simultaneously.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable configs related to USB Host mode, Peripheral mode and DFU.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently the DM37 and OMAP35 boards do not boot due to SPL
bring too large.
SPL doesn't need GPIO, I2C nor MMC sector access since it uses
a FAT file system.
This patch unifies all these boards to remove these unused features
from their defconfigs
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add new defconfig files for the J721e High Security EVM.
These defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync new additions to non-HS defconfig with HS defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync new additions to non-HS defconfig with HS defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adding the configurations to the evm_defconfig file
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig
for ST board with NOR support (STM32MP15xx-EV1 boards)
- CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB)
- CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH)
This Patch prepares the U-Boot support of boards with STM32MP15x SOC
not provided by STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Clearfog: Fix SD booting (Baruch)
- Misc updates to MMC handling in SPL to support booting from
main data partition (vs hardware boot partition) on MVEBU (Baruch)
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig
to fix the mt7623 compile error after building others mediatek target
platform
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Armada 38x ROM skips the first SD card offset when loading SPL. This
affects the location of the main U-Boot image. SPL MMC code now supports
U-Boot image offset based on run-time detection of the boot partition.
Use this feature to make the same generated image support both SD card
and eMMC boot partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL needs DM GPIO to read the SD card-detect signal. This complements
the fix in commit 70bae02f71 ("arm: mvebu: clearfog: fix boot from SD
card").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For DM_ETH support , it's require to disable this config.
When this config is enable, This generate a error with spl in linker script
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Some i.MX8QXP MEK boards do not have MAC address stored
and hang during eth driver probe:
Error: ethernet@5b040000 address not set.
(Board hangs)
To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that
a valid MAC address can be used in such case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Qemu v4.2.0 maps bootmode registers to address space which was the reason
why board_late_init() was disabled and accesses were failing.
With new Qemu board_late_init() can be called without any issue.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zcu1285 is the same as zcu1275 but it is using Avnet FMC
http://www.ultrazed.org/product/network-fmc-module
Unfortunately not everything is connected now that's why this is only
describing system which Xilinx is using.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Decrease amount of the similar defconfigs and use generic one instead.
The change was declared by commit 4b37c13dc3
("arm64: zynqmp: Introduce virtual defconfig") and this patch removes
configs for the most of the boards.
Utra96/zcu100/zcu102/zcu102 and ZynqMP based System controllers *a2197*.
have been also boot tested to make sure that funcionality
remains the same.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These options are taken from zcu102/104 platforms. Also use OF_SEPARATE
instead of OF_BOARD. Maybe at some point this option will be taken back but
as of now board detection is not ready.
export DEVICE_TREE="zynqmp-zcu102-revA"
make xilinx_zynqmp_virt_defconfig
make -j
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In past SPL_ZYNQMP_TWO_SDHCI symbol was introduced to handle boards with
two sdhci controllers. The problem was that U-Boot is registering
controllers based on aliases in DT but bootmode targets specific controller
ID. That's why on boards with one "second" sdhci controller bootmode was
pointing to second controller(MMC2) but alias was setup to mmc0 (the first
controller). And SPL requires to point to mmc0 in this case.
Long time ago commit f101e4bd37
("spl: add support for alternative boot device") added support for handling
multiple bootmodes in SPL. Use this functionality and setup second sdhci
controller as backup boot device.
Below is table with behavior:
HW/bootmode bootorder
sd0/sd0 mmc0/mmc1 (mmc1 never called)
sd1/sd1 mmc1/mmc0 (mmc0 fails and mmc1 is called)
sd0+sd1/sd0 mmc0/mmc1 (mmc1 never called)
sd0+sd1/sd1 mmc1/mmc0 (mmc0 never called)
All other bootmodes are not affected but order can be extended to cover
advance boot flows.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These commands are useful in connection to usb and other devices that's why
enable it by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
[*] https://patchwork.ozlabs.org/patch/1182212/#2291600
[**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o)
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass<sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
The M25P80 and M25P32 SPI flashes from Numonix/Micron
will be replaced by Marconix MX25L80 and MX25L32 flashes.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch only fixes a typo.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl4UvR4ACgkQxIHbvCwF
GsRJZhAAmlsRBUS3fvFV5GtB8bkWcSU4/s3TVYJui0fOhY02ZDIKkrubZzDx/Lgv
9OaVwjQ3JSmq5XkDmXqzNDzYkxitQ5Qf/cFiBF5HpA3USkOttb3GIfgj0qD6DGzM
cKyhgJm7bZoMN/mkIzkWsry1ASwYpB3ipyoJAfRfryw9ok4j9RfJ7pPieeycGWGJ
0sZsJI0v7e6xt5Qsytk5sZNvlCFhyhl2OMYliAlRKBryh31Ahr2e6KEwsJh7VyCP
4K12eBTqIJq1qHk7Lr0g1CnMCdeOT8J7qvX1+kvt3HupxTMkYRv2AR5CQWRKck5E
RsmcKmiTHz/76w6Gk7kLan7y0UCSHnfHQ3aSEkkx4O/v4OC85VteyLAEriS7J9Hx
xSNyoj01U2wG3SLrUjkAZv6JgyC8uCezRzOHOqN25Q2mRROVq781mcMfRXwdq6cD
L4rrTsIDPzNF19wDa7P5tK6JMF8BDifLNuMTQj5LdJYMHJTJZBWG/vTNFPEldaIP
D9RPoCibTolpiuCYneeXJURHGm5yme7KoxAPiMU+fAWO1F6SO25zxYA7MAiY4OYw
zk7Ipaat0luIu1gC2ICYxrLnsMBq9glABrdq99i0DpUg9n9N/7SpcJSj2DMrFGmY
u4yenWM1KTgjLoVHRhpTbCzF15GlYN4SHXV5iYO+Pof5WQYnv8w=
=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
enable CONFIG_CMD_ERASEENV to make it easy to erase env.
Use savedefconfig to generate new defconfig.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable support for random number generator on sandbox configs. This is
aimed primarily at adding unit test support for rng uclass.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable support for the rng device on the stm32mp15 configs.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Khadas VIM3L uses the same board layout as VIM3, but with an S905D3 chip
instead of A311D. Board config is derived from khadas-vim3_defconfig and
sei610_defconfig. README is based on README.khadas-vim3; the difference
is that VIM3L uses FIP files from the g12a folder in vendor sources not
the g12b folder.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added vim3l readme into w400 MAINTAINERS]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.