This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
- Some Kirkwood boards converted to DM_SPI by Chris
- New Armada-385 SoC revision printed by Chris
- Ethernet enable on mcbin by Baruch
- Support 2 DRAM banks on Armada-8k boards by Baruch
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Pine64 LTS is an updated version of the Pine64, copying the
technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and
soldered SPI flash chip, even the broken SD card detect pin has been copied.
Consequently this leads to the .dts (copied from the kernel) just including
the SoPine baseboard .dts, and the defconfig being almost identical.
Nevertheless the boards deserves a separate config.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the
compatible name for the syscon controller, dropping the generic "syscon"
fallback. Using this new DT node will make the Ethernet driver in every
older kernel (or non-Linux kernels) fail to initialise the MAC device.
To allow booting distribution kernels (from installer images via UEFI,
for instance), re-add the syscon compatible string as a fallback. This
works with both older and newer kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 3c28576bb0 ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is a large update of the AST2500 SoC DTS file bringing it to the
level of commit 927c2fc2db19 :
Author: Joel Stanley <joel@jms.id.au>
Date: Sat Jun 2 01:18:53 2018 -0700
ARM: dts: aspeed: Fix hwrng register address
There are some differences on the compatibility property names. scu,
reset and clock drivers are also different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Introduce dtsi for i.MX8QXP, since there is other variants i.MX8DX(P),
so add them there, because i.MX8QXP includes the dtsi of them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
